Now that the IPMI DMI code creates a platform device for IPMI devices
in the firmware, use that instead of handling all the DMI work
in the IPMI drivers themselves.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Andy Lutomirski <luto@kernel.org>
The null check on client->adapter->name is redundant as name is an
array of I2C_NAME_SIZE chars and hence can never be null. We may as
well remove this redundant check.
Detected by CoverityScan, CID#1375918 ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We should unlock and re-enable IRQs if this allocation fails.
Fixes: 259307074b ("ipmi: Add SMBus interface driver (SSIF) ")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
msg_written_handler() may set ssif_info->multi_data to NULL
when using ipmitool to write fru.
Before setting ssif_info->multi_data to NULL, add new local
pointer "data_to_send" and store correct i2c data pointer to
it to fix NULL pointer kernel panic and incorrect ssif_info->multi_pos.
Signed-off-by: Joeseph Chang <joechang@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 3.19-
When added by ACPI, the information does not contain the slave address
of the BMC. However, that information is available from SMBIOS. So
if we add a device that doesn't have a slave address, look at the other
devices that are duplicate interfaces and see if they have a slave
address.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
.alert() is meant to be generic, but there is currently no way
for the device driver to know which protocol generated the alert.
Add a parameter in .alert() to help the device driver to understand
what is given in data.
This patch is required to have the support of SMBus Host Notify protocol
through .alert().
Tested-by: Andrew Duggan <aduggan@synaptics.com>
For hwmon:
Acked-by: Guenter Roeck <linux@roeck-us.net>
For IPMI:
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Unlike everywhere else in the IPMI specification, the I2C address
specified in the SPMI table is not shifted to the left one bit with
the LSB zero. Instead it is not shifted with the MSB zero.
Reported-by: Sanjeev <singhsan@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This patch replaces timeval with timespec64 as 32 bit 'struct timeval'
will not give current time beyond 2038.
The patch changes the code to use ktime_get_real_ts64() which returns
a 'struct timespec64' instead of do_gettimeofday() which returns a
'struct timeval'
This patch also alters the format string in pr_info() for now.tv_sec
to incorporate 'long long' on 32 bit architectures.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are broken on some platforms, this gives people a chance to work
around it until the firmware is fixed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Constify the ACPI device ID array, it doesn't need to be writable at
runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Lots of little fixes for multi-part messages:
The values was not being re-initialized, if something went wrong
handling a multi-part message and it got left in a bad state, it
might be an issue.
The commands were not correct when issuing multi-part reads, the
code was not passing in the proper value for commands. Also clean
up some minor formatting issues.
Get the block number from the right location, limit the maximum send
message size to 63 bytes and explain why, and fix some minor sylistic
issues.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The SSIF interface can optionally have an SMBus alert come in when
data is ready. Unfortunately, the IPMI spec gives wiggle room to
the implementer to allow them to always have the alert enabled,
even if the driver doesn't enable it. So implement alerts.
If you don't in this situation, the SMBus alert handling will
constantly complain.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
commit d6c5dc18d8 ("ipmi: Remove uses of return value of seq_printf")
incorrectly changed the return value of various proc_show functions
to use seq_has_overflowed().
These functions should return 0 on completion rather than 1/true
on overflow. 1 is the same as #define SEQ_SKIP which would cause
the output to not be emitted (skipped) instead.
This is a logical defect only as the length of these outputs are
all smaller than the initial allocation done by the seq filesystem.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Some of the adapters have spaces in their names, but that's really
hard to pass in as a module or kernel parameters. So ignore the
spaces.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The code was using an normal completion, but that caused stuck
task errors after a while. Use an interruptible one to avoid that.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The seq_printf like functions will soon be changed to return void.
Convert these uses to check seq_has_overflowed instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
