The ADV7175A/ADV7176A can operate in either 8-bit or 16-bit YCrCb mode.
* 8-Bit YCrCb Mode
This default mode accepts multiplexed YCrCb inputs through
the P7-P0 pixel inputs. The inputs follow the sequence Cb0, Y0
Cr0, Y1 Cb1, Y2, etc. The Y, Cb and Cr data are input on a
rising clock edge.
* 16-Bit YCrCb Mode
This mode accepts Y inputs through the P7–P0 pixel inputs and
multiplexed CrCb inputs through the P15–P8 pixel inputs. The
data is loaded on every second rising edge of CLOCK. The inputs
follow the sequence Cb0, Y0 Cr0, Y1 Cb1, Y2, etc.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes incorrect return value. Errors should be returned
as negative numbers.
Reported-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pidgin uses gstreamer (and libv4l) to work. Without implementing this ioctl,
it won't detect properly the size range, and driver will fail.
So, this patch is required, in order to use an em27xx webcam, like
Silvercrest.
The pigdin/gstreamer/libv4l needs to be fixed, as it shouldn't assume
that all drivers will implement this optional ioctl, but, at least now,
devices with em28xx have a better chance of working with pidgin.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Safety reasons. We shouldn't be trying to reconfigure a risc
processor instruction queue unless it's stopped.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previous driver over-reported errors and stopped the video fifo
(causing video to stop) if 1) A risc error occured 2) The risc processor
detected that it has missing lines in the video frame 3) The risc fifo
is about to overflow.
The previous driver reported all three of these cases as risc errors
when this is technically not correct. So, the function was cleaned up.
1. Ensure that risc opcode related errors are correctly shown as such,
and not overly reported for non-risc-opcode cases.
2. Ensure that line sync and overflow errors are not reported as opcode errors.
3. Ensure that only the risc-op-code case can stop the fifo and dump channel
/ risc processor information.
The net result is that if video becomes unstable, cable disconnect, this will
not trigger a stop of the video firmware (due to missing lines errors).
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. Removed the verbose 'dump channel state to console', very noisy in
weak signal conditions.
2. No need for the video buffer timeout to stop the risc engine here.
Clearer and easier to maintain if start_video_dma() is the single
place that this is done.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Inform applications that multiple audio inputs are available on
non-tv inputs.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure audio is established at driver start.
Ensure the correct defaults are established for the audio path if
the cards struct has nothing defined.
Allow the caller to select one of the two baseband input paths.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code to program the flatiron internal i2c ADC and pass the
appropriate audio mux enums to the cx25840 driver.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The change effects cx23885 boards only and preserves support for existing
boards. Essentially, if we're using baseband audio into the cx23885 AV
core then we have to patch registers. The cx23885 driver will call
with either CX25840_AUDIO8 to signify tuner audio or AUDIO7 to
signify baseband audio. If/When we become more comfortable with this change
across a series of products then we may decide to relax the cx23885 only
restriction.
[liplianin@netup.ru: fix missing state declaration]
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Coding style and printk's cleaned up in following patches.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change is probably good for other boards also, but the change
has limited scope and is reasonably safe.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Coding style and printk's are cleaned up in subsequent patches
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A handlful of coding style issue cleaned up in the following patches.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_g_tuner should not do any memset for the parameters. Core
already does that. In particular, V4L2 core now does some handling
for the tuner type, and the tuner-core module relies on that.
So, doing any memset there is a very bad idea.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[stoth@kernellabs.com: add it to the makefile and fix snd_card binding]
[liplianin@netup.ru: videobuf: Remove the videobuf_sg_dma_map/unmap functions]
Signed-off-by: Mijhail Moreyra <mijhail.moreyra@gmail.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stb0899_status stb0899_check_data the first read of STB0899_VSTATUS
could read old (from previous search) LOOP status bit and the search
fails on a good frequency.
With the patch more transponder could be locked and locks about 2*
faster.
Signed-off-by: Lutz Sammer<johns98@gmx.net>
Reviewed-by: Manu Abraham<manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code here treated user pointers correctly, but the __user tags
weren't used correctly so it caused Sparse warnings:
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the tuner is constantly powered causing these effects.
1. Remembering last tune channel causing corruptions of changing channel.
2. Causing corruption on other frontend.
3. Higher current in standby of demodulator with clock running.
Power sequence now follows;
Power Up
Tuner on -> Frontend suspend off -> Tuner clk on
Power Down
Frontend suspend on -> Tuner clk off -> Tuner off
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tvp5150 video decoder has two operation modes to configure the video
standard used.
If auto-switch mode is enable, the device can sense the signal and detect which
video standard the device is operating. Also the device can be forced to use a
user defined video standard.
Each operation mode uses a different register and the bitmask values to
represent each standard is different.
So we add video standard constants for both autoswitch and no-autoswitch mode.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both mt9t001.c and mt9p031.c have two identical issues, those
being that they will need module.h inclusion for the upcoming
cleanup going on there, and that their dependencies don't limit
selection of configs that will fail to compile as follows:
The related config options are CONFIG_MEDIA_CONTROLLER and
CONFIG_VIDEO_V4L2_SUBDEV_API. Looking at the code, it appears
that the driver was never intended to work without these enabled,
so add a dependency on CONFIG_VIDEO_V4L2_SUBDEV_API, which in
turn already has a dependency on CONFIG_MEDIA_CONTROLLER.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As msp3400 allows standards detection, add support for it. That
efectivelly means that devices with msp3400 can now implement
VIDIOC_QUERYSTD, and it will provide very good detection for
the standard, specially if combined with a video decoder detection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using V4L2_STD_ALL when no standard is detected,
trust that the maximum allowed standards are already filled by
the V4L2 core. It is better this way, as the bridge and/or the audio
decoder may have some extra restrictions to some video standards.
This also allow other devices like audio and tuners to contribute to
standards detection, when they support such feature.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with the V4L2 API spec:
"When detection is not possible or fails, the set must contain
all standards supported by the current video input or output."
The V4L2 core has the mask with all supported standards already. So,
apply it. Driver and subdevs can then just remove standards from the
mask, as they're able of detecting audio, video and frames frequency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several bugs at saa7115 standards detection:
After the fix, the driver is returning the proper standards,
as tested with 3 different broadcast sources:
On an invalid channel (without any TV signal):
[ 4394.931630] saa7115 15-0021: Status byte 2 (0x1f)=0xe0
[ 4394.931635] saa7115 15-0021: detected std mask = 00ffffff
With a PAL/M signal:
[ 4410.836855] saa7115 15-0021: Status byte 2 (0x1f)=0xb1
[ 4410.837727] saa7115 15-0021: Status byte 1 (0x1e)=0x82
[ 4410.837731] saa7115 15-0021: detected std mask = 00000900
With a NTSC/M signal:
[ 4422.383893] saa7115 15-0021: Status byte 2 (0x1f)=0xb1
[ 4422.384768] saa7115 15-0021: Status byte 1 (0x1e)=0x81
[ 4422.384772] saa7115 15-0021: detected std mask = 0000b000
Tests were done with a WinTV PVR USB2 Model 29xx card.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.
Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.
Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.
Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.
Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This lock should be released as well on the error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Patrick Boettcher <Patrick.Boettcher@dibcom.fr>
Cc: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Negate has higher precedence than bitwise AND. I2C_M_RD is 0x1 so
the original code is equivelent to just checking if (!msg->flags).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.
This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These are necessary to prevent dead-locks e.g. if one thread waits
in dqbuf at one end and another tries to queue a buffer at the
other end.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Pawel Osciak <pawel@osciak.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes mbus configuration between Mixer, SDO and HDMI. The SDO
accepts only YUV444 on input. The HDMI in DVI mode accepts only RGB888. Now
Mixer is choosing proper output format depending on mbus format.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Current version of the driver does not support HDMI features
not present in DVI standard. Therefore DVI mode is used to
keep compatibility with DVI devices.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The TVOUT driver requires PM_RUNTIME support for proper clock
enabling.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplifies the locking by moving the em28xx_init_extension() call until
em28xx_usb_probe() has finished with the dev->lock mutex. It therefore
makes the second and subsequent "plugging" events logically identical to
the first "plugging" event when the em28xx-dvb and em28xx-alsa modules
must be loaded (i.e. registered).
Basically, em28xx_usb_probe() requests that em28xx-dvb be loaded and
also triggers udev to initialise the V4L2 devices. These two events are
serialised by the dev->lock mutex but the order that they happen in is
undefined. But this has always been the case anyway.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch just removes the prototypes for the two functions that I've already
deleted in my previous patches.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the deadlock that occurs with either multiple PCTV 290e adapters or when a single PCTV 290e adapter is replugged.
For DVB devices, the device lock must now *not* be held when adding/removing either a device or an extension to the respective lists. (Because em28xx_init_dvb() will want to take the lock instead).
Conversely, for Audio-Only devices, the device lock *must* be held when adding/removing either a device or an extension to the respective lists.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the stv090x driver only set the status bits to SCVYL when
there is a lock. This patch set the right bits even if there is no lock.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With VDR streaming HDTV into network, generating an interrupt once per 16kb,
implemented in this patch, seems to support more robust throughput with HDTV.
Fix leaking almost 64kb data from the previous TS after changing the TS.
One effect of the old version was, that the DMA transfer and driver's
DMA buffer access might happen at the same time - a race condition.
Signed-off-by: Marko M. Ristola <marko.ristola@kolumbus.fi>
Reviewed-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I noticed a stray 0x00 at init on DiSEqC bus (KNC1 DVB-S2) with a DiSEqC
tool analyzer.
I removed the register from initialization table and all seem to go well
(at least for my KNC board).
Signed-off-by: Florent Audebert <florent.audebert@anevia.com>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch closes the race on the device and extension lists at USB disconnect
time. Previously, the device was removed from the device list during
em28xx_release_resources(), and then passed to the em28xx_close_extension()
function so that all extensions could run their fini() operations. However, this
left a (brief, theoretical, highly unlikely ;-)) window between these two calls
during which a new module could call em28xx_register_extension(). The result
would have been that the em28xx_usb_disconnect() function would also have passed
the device to the new extension's fini() function, despite never having called
the extension's init() function.
This patch also restores em28xx_close_extension()'s symmetry with
em28xx_init_extension(), and establishes the property that every device in the
device list must have been initialised for every extension in the extension list.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
(Resending because Mauro reported losing some emails on IRC)
Provide CX2388[578] IR receive timeout (RTO) reports in the
final space raw event sent up the chain to the raw IR pulse
decoders. This should allow the lirc decoder to actually
measure the inter-transmission gap properly.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to put the IRQ number in driver's private platform
data structure as this can also be passed in struct i2c_lient.irq.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to generic media bus signal polarity flags and allow
configuring the FIELD signal polarity.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts some ifdef'd wrapper functions from macros to static inline
functions to kill the following warnings issued by GCC:
CC [M] drivers/media/rc/ir-raw.o
drivers/media/rc/ir-raw.c: In function ‘init_decoders’:
drivers/media/rc/ir-raw.c:353:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:354:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:355:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:356:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:357:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:359:2: warning: statement with no effect [-Wunused-value]
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the choice of the alternate setting has been enhanced in the gspca main,
forcing its number here is no more useful.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG quality was guessed as around 82%. Information in ms-win drivers
says it should be 85%.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams ask for a greater time to start.
This patch increases the delay before timeout error on capture start.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is based on Anders Blomdell's source proposed in april 2009.
It has been extended to handle the tp6810 bridge and the soi763a sensor.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adapted from a patch from Sarah Sharp (2010/05/03).
The xHCD handler checks the USB bandwidth on usb_set_interface()
instead of on usb_submit_urb().
Now, the same treatment is applied in case of error of both functions.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously image transfer used to use the highest altsetting, which, most of
the time, took the whole USB bandwidth.
Now, the altsetting is chosen according to an estimation of the bandwidth
needed for image transfer.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sd_isoc_init() did only a set interface which is done in gspca main.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct tuner settings for more accuracy. This now makes the tuner
section more compatible with other versions of the IT913X
series.
TODOs
Version 2 chip
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add remote support for KWORLD UB499-2T-T09
The remote supplied is the same as KWORLD_315U.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an improved version of the patch I sent a little ago.
The problem was:
On my DC-1125 webcam chip from Syntek, whenever the webcam turns
on, the LED light on it is turned on also and never turns off again unless
system is shut downed or restarted.
The previous version seemed to break some other laptop webcam work. Thanks
to Andrea Anacleto for the bug report and solution.
Signed-off-by: Andrea Anacleto <andreaanacleto@libero.it>
Signed-off-by: Arvydas Sidorenko <asido4@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ioctls on the subdevs node currently don't dispatch the register access debug
driver callbacks. Add the dispatching with the same security checks are for
non subdev video nodes (i.e. only capable(CAP_SYS_ADMIN may call the register
access ioctls).
Signed-off-by: Martin Hostettler <martin@neutronstar.dyndns.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove VPBE_DISPLAY_SD_BUF_SIZE as it is no longer used.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC driver uses usb_alloc_coherent() to allocate DMA data buffers.
On systems without coherent DMA this ends up allocating buffers in
uncached memory. The subsequent memcpy's done to coalesce the DMA
chunks into contiguous buffers then run VERY slowly. On a MIPS test
system the memcpy is about 200 times slower. This issue prevents the
system from keeping up with 720p YUYV data at 10fps.
The following patch uses kmalloc to alloc the DMA buffers instead of
usb_alloc_coherent on systems without coherent DMA. With this patch
the system was easily able to keep up with 720p at 10fps.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVCIOC_CTRL_ADD, UVCIOC_CTRL_MAP_OLD, UVCIOC_CTRL_GET and
UVCIOC_CTRL_SET ioctls are deprecated and were scheduled for removal for
v2.6.42. As v2.6.42 == v3.2, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Imaging Source CCD cameras use a vendor specific interface class
even though they are actually UVC compliant.
Signed-off-by: Arne Caspari <arne@unicap-imaging.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a merge conflict]
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The protocol differs by having two toggle bits in the scancode. Since
one of the bits is otherwise unused, we can safely handle the bits
unconditionally.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ati_remote_dump() function tries to not print "Weird byte" warning
for 1-byte responses that contain 0xff or 0x00, but it doesn't work
properly as it simply falls back to the "Weird data" warning in the else
clause.
Fix that by adding an inner if clause.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The keycode mangling algorithm is kept the same, so the new external
keymap has the same values as the old static table.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver will be migrated to the RC driver API in a following
commit.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The type of a media entity is default for this driver. This patch makes it
explicitly defined as MEDIA_ENT_T_V4L2_SUBDEV_FLASH.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register values changed according to the data sheet and Texas Instruments DaVinci_PSP_03_02_00_37.
- TVP7002_RGB_COARSE_CLAMP_CTL changed to the default value in data sheet.
- TVP7002_HPLL_PHASE_SEL deleted because the registers write to reserved bits. The default value works fine.
Signed-off-by: Mats Randgaard <mats.randgaard@tandberg.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following build error occurs with 3.1-rc5:
CC drivers/media/video/omap3isp/ispccdc.o
This patch adds the missing 'linux/slab.h' include to fix the problem.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvc_mc_register_entity() function wrongfully selects the
media_entity associated with a UVC entity when creating links. This
results in access to uninitialized media_entity structures and can hit a
BUG_ON statement in media_entity_create_link(). Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_disconnect() calls dev_get_drvdata() and dev_set_drvdata()
on the device it received in v4l2_device_register(). Get a reference to
the device in v4l2_device_register() to make sure it won't disappear as
long as we need it.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that have no v4l2_device release callback might free the
v4l2_device instance in the video_device release callback. Make sure we
don't access the v4l2_device instance after it gets freed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the bus has been reset on resume, set the alternate setting to 0.
This should be the default value, but some devices crash or otherwise
misbehave if they don't receive a SET_INTERFACE request before any other
video control request.
Microdia's 0c45:6437 camera has been found to require this change or it
will stop sending video data after resume.
uvc_video.c]
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DSS2 driver does not support the configuration of the update_mode of a
panel anymore. Remove the setting of update_mode done in omap_vout_probe().
Ignore configuration of TE since omap_vout driver doesn't support manual update
displays anyway.
Signed-off-by: Archit Taneja <archit@ti.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FEC fix patch fixed locking on 11,681 Ghz, but not on 12,692 Ghz for
me.
Reviewed-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reduce buffer size of Interupt urb to 128 bytes and polling
interval to 8.
The devices buffer appears to only handle a maxium of 40 bytes.
If the buffer is full a slowing effect is noticed causing occasionnal
dropped streaming packets.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 04/09/11 00:49, Mauro Carvalho Chehab wrote:
> This is an automatic generated email to let you know that the following patch were queued at the
> http://git.linuxtv.org/media_tree.git tree:
>
> Subject: [media] em28xx: use atomic bit operations for devices-in-use mask
> Author: Chris Rankin<rankincj@yahoo.com>
> Date: Sat Aug 20 08:21:03 2011 -0300
>
> Use atomic bit operations for the em28xx_devused mask, to prevent an
> unlikely race condition should two adapters be plugged in
> simultaneously. The operations also clearer than explicit bit
> manipulation anyway.
>
> Signed-off-by: Chris Rankin<rankincj@yahoo.com>
> Signed-off-by: Mauro Carvalho Chehab<mchehab@redhat.com>
>
> drivers/media/video/em28xx/em28xx-cards.c | 33 ++++++++++++++---------------
I think you missed this line in the merge.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MT9T001 is a parallel 3MP sensor from Aptina (formerly Micron)
controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports binning and
cropping, and the gain, exposure, test pattern and black level controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If streaming can't be enabled on the pipeline, the DMA buffers queue is
not emptied. If the buffers then get freed the queue will end up
referencing free memory. This is usually not an issue, as the DMA queue
will be reinitialized the next time streaming is enabled, before
enabling the hardware.
However, if the sensor connected at the pipeline input is free-running,
the CCDC will start generating interrupts as soon as it gets powered up,
before the streaming gets enabled on the hardware. This will make the
CCDC interrupt handler access freed memory, causing a crash.
Reinitialize the DMA buffers queue in isp_video_streamon() if the error
path to make sure this situation won't happen.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code handles subdevs with no s_stream operation correctly, but
returns -ENOIOCTLCMD by mistake if the first subdev in the chain has no
s_stream operation. Return 0 in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
adp1653.c uses interfaces that are provided by <linux/module.h>
and needs to include that header file to fix build errors.
and more.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon devices have either 1 or 2 usb interfaces on them, each wired
up to its own urb callback. The interface 0 urb callback is wired up
before the imon context's rc_dev pointer is filled in, which is
necessary for imon 0xffdc device auto-detection to work properly, but we
need to make sure we don't actually run the callback routines until
we've entirely filled in the necessary bits for each given interface,
lest we wind up oopsing. Technically, any imon device could have hit
this, but the issue is exacerbated on the 0xffdc devices, which send a
constant stream of interrupts, even when they have no valid key data.
CC: Andy Walls <awalls@md.metrocast.net>
CC: Chris W <lkml@psychogeeks.com>
Reported-by: Chris W <lkml@psychogeeks.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch provides wider carrier search.
As with existing code search starts at MSB aligned. The boundary
is widened to start at -9. In order to save time, if no carrier is
detected at the start it advances to the next alignment until carrier
is found.
The stv0288 will detect a DVB-S2 carrier on all steps , a
time out of 11 steps is introduced to drop out of the loop.
In stv0288_set_symbol carrier and timing loops are restored to
default values (inittab) before setting the symbol rate on each tune. A
slight drift was noticed with full scan in the higher IF frequencies of
each band.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is now not needed as the sensor identification is done
through the media controller API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SR030PC30, NOON010PC30, M5MOLS are camera sensors so better place
for them is under the "Camera sensors" Kconfig section.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the now unneeded check for the platform data in s_power
handler and the platform data pointer in struct noon010_info.
Also do not reset the configured output resolution and pixel
format when cycling sensor's power.
Add small delay for proper reset signal shape.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace g/s_mbus_fmt ops with the pad level get/set_fmt operations.
Add media entity initialization and set subdev flags so the host driver
creates a subdev device node for the driver.
A mutex was added for serializing the subdev operations. When setting
format is attempted during streaming an (EBUSY) error will be returned.
After the device is powered up it will now remain in "power sleep"
mode until s_stream(1) is called. The "power sleep" mode is used
to suspend/resume frame generation at the sensor's output through
s_stream op.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use resource_size function on resource object
instead of explicit computation.
The semantic patch that makes this output is available
in scripts/coccinelle/api/resource_size.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_stream does nothing in current form so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the auto cluster core changed to a different scheme of how to
handle volatile controls (including how to switch from auto to manual mode)
the pwc code can be simplified to use that new core support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem tackled in this patch is how to handle volatile autoclusters
correctly. A volatile autocluster is a cluster of related controls where one
control is the control that toggles between manual and auto mode and the other
controls are the values for the manual mode. For example autogain and gain,
autoexposure and exposure, etc.
If the hardware lets you read out the automatically calculated manual values
while in automode, then those manual controls should be marked volatile.
gain value as calculated by the autogain circuitry, then you would mark the
gain control as volatile (i.e. continuously changing).
The question in such use cases is what to do when switching from the auto
mode to the manual mode. Should we switch to the last set manual values or
should the volatile values be copied and used as the initial manual values.
For example: suppose the mode is manual gain and gain is set to 5. Then
autogain is turned on and the gain is set by the hardware to 2. Finally
the user switches back to manual gain. What should the gain be? 2 or 5?
After a long discussion the decisions was made to keep the last value as
calculated by the auto mode (so 2 in the example above).
The reason is that webcams that do such things will adapt themselves to
the current light conditions and when you switch back to manual mode you
expect that you keep the same picture. If you would switch back to old
manual values, then that would give you a suddenly different picture,
which is jarring for the user.
Additionally, this would be difficult to implement in applications that
store and restore the control values at application exit and start.
If you want to keep the old manual values when you switch from auto to
manual, then there would have to be a way for applications to get hold
of those old values while in auto mode, but there isn't.
So this patch will do all the heavy lifting in v4l2-ctrls.c: if you go
from auto mode to manual mode and the manual controls are volatile, then
g_volatile_ctrl will be called to get the current values for the manual
controls before switching to manual mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
