Cleaning up the flow of the representors' rx initialization, towards
enabling RSS for the representors.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enabled checksum and TSO offloads for the representors, in
order to increase their performance, which is required to
increase the performance of flows that cannot be offloaded.
Checksum offloads contribute to a general acceleration of all
traffic (to around 150%), whereas the TSO offload contributes
to a prominent acceleration of the representor's TX for traffic
flows with larger than MTU sized packets (to around 200%). This
is the usual case for TCP streams, as the PF, which serves as
the uplink representor, and the VF representors employ GRO before
forwarding the packets to the representor.
GRO was enabled implicitly for the representors beforehand, and
is explicitly enabled here to ensure that the representors preserve
the performance boost it provides (of around 200%) when working in
tandem with the TSO offload by the forwardee, which is the standard
case as both the PF and the VF representors employ HW TSO.
The impact of these changes can be seen in the following
measurements taken on a setup of a VM over a VF, connected
to OVS via the VF representor, to an external host:
Before current changes:
TCP Throughput [Gb/s]
External host to VM ~ 10.5
VM to external host ~ 23.5
With just checksum offloads enabled:
TCP Throughput [Gb/s]
External host to VM ~ 14.9
VM to external host ~ 28.5
With the TSO offload also enabled:
TCP Throughput [Gb/s]
External host to VM ~ 30.5
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The representors' RQ size was not large enough for them to achieve
high enough performance, and therefore needed to be enlarged, while
suffering a minimum hit to its memory usage. To achieve this the
representors RQ size was increased, and its type was changed to be a
striding RQ if it is supported.
Towards that goal the following changes were made:
* Extracted the sequence for setting the standard netdev's RQ parmas
into a function
* Replaced the sequence for setting the representor's RQ params with
the standard sequence
The impact of this change can be seen in the following measurements
taken on a setup of a VM over a VF, connected to OVS via the VF
representor, to an external host:
Before current change:
TCP Throughput [Gb/s]
VM to external host ~ 7.2
With the current change (measured with a striding RQ):
TCP Throughput [Gb/s]
VM to external host ~ 23.5
Each representor now consumes 2 [MB] of memory for its packet
buffers.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow using partial masks for L3 addresses and L4 ports across
the place.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function ‘hclge_get_sset_count’:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:496:31: error: ‘HNAE3_REVISION_ID_21’ undeclared (first use in this function); did you mean ‘FADT2_REVISION_ID’?
if (hdev->pdev->revision >= HNAE3_REVISION_ID_21 ||
^~~~~~~~~~~~~~~~~~~~
FADT2_REVISION_ID
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c: In function ‘hns3_self_test’:
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c:278:15: error: ‘HNS3_SELF_TEST_TYPE_NUM’ undeclared (first use in this function); did you mean ‘HNS3_SELF_TEST_TPYE_NUM’?
int st_param[HNS3_SELF_TEST_TYPE_NUM][2];
^~~~~~~~~~~~~~~~~~~~~~~
HNS3_SELF_TEST_TPYE_NUM
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-09-27
This series contains fixes to the ice driver only.
Jake fixes a potential crash due to attempting to access the mutex which
is already destroyed. Fix this by using rq.count and sq.count to
determine if the queue was initialized. Fixed the current logic for
checking the firmware version to properly handle situations when
firmware major/minor versions differ and when the branch version
differs.
Bruce replaces a memcpy() with a direct assignment, which is preferred.
Also updated the branding strings and device ids supported by the
driver. Fixed the "ethtool -G" command in the driver, which was always
returning EINVAL when changing the descriptor ring size.
Brett update and clarified code comments.
Anirudh updates the driver to ensure we query the firmware for the
transmit scheduler node information before adding it to the driver
database, to ensure we have the current information. Also update the
"get capabilities" command to get device and function capabilities.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The user's coal configuration will be lost after reset, so the tx_coal
and rx_coal fields are added to the struct hns_nic_priv to save the coal
configuration and used to restore the user's configuration after the reset
is complete.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current hns3_get_max_available_channels returns the total number
of queues for the device, which makes ethtool -L set the number of queues
per channel queues incorrectly, so hns3_get_max_available_channels should
return the maximum available number of queues per channel, depending on
the total number of queues allocated and the hardware configurations.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_tm_schd_info_update should return an error when num_tc is greater
than alloc_tqps.
This patch changes the return type of hnae3_register_ae_algo from void
to int.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hns3_nic_change_mtu will try to down the netdev before
setting mtu, and it does not up the netdev when the setting fails,
which causes netdev not up problem.
This patch fixes it by not returning when the setting fails.
Fixes: a8e8b7ff35 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects a unit of 128 bytes when setting
packet buffer. When calculating the packet buffer size,
hclge_rx_buffer_calc does not round up the size as a unit
of 128 byte, which may casue packet lost problem when stress
testing.
This patch fixes it by rounding up packet size when calculating.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds serdes parallel inner loopback support for self test.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fact, our implementation of mac loopback is the implementation of app
loopback now. Current name is wrong. This patch renames mac loopback to
app loopback.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our loop mode includes mac loop, serdes loop and phy loop. Not all of them
are related with mac. This patch corrects their names.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra mac address of pause param is used to do double check
for pause frame. This patch set it to HW. If we do not do that,
pfc pause frame will be transferred protocol stack when normal
flow control mode is enabled.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for sctp checksum offload.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that removed the only users of the oldadv/newadv variables
accidentally left the now-unused declarations behind:
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c: In function 'dpaa_set_pauseparam':
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:14: error: unused variable 'oldadv' [-Werror=unused-variable]
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:6: error: unused variable 'newadv' [-Werror=unused-variable]
Fixes: 70814e819c ("net: ethernet: Add helper for set_pauseparam for Asym Pause")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:873:5: warning:
symbol 'aq_fw1x_set_power' was not declared. Should it be static?
Fixes: a0da96c08c ("net: aquantia: implement WOL support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_delete_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:354:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_join_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:463:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
Since commit 1eec2437d1 ("qed: Make OOO archipelagos into an array"),
'p_archipelago' is no longer in use.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_mini_pending was set to an incorrect value. This was causing EINVAL to
always be returned to 'ethtool -G'. The driver does not support mini or
jumbo rings so the respective settings should be zero.
Also, change the valid range of the number of descriptors in the rings to
make the code simpler and easier for users to understand (this removes the
valid settings of 8 and 16). Add a system log message indicating when the
number is rounded-up from what the user specifies with the 'ethtool -G'
command (i.e. when it is not a multiple of 32), and update the log message
when a user-provided value is out of range to also indicate the stride.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes a couple of changes in the way the driver uses the
"get capabilities" command.
1. Get device capabilities in addition to function capabilities
2. Align to latest spec by using cap_count to determine size of the
buffer in case of length error.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Query the Tx scheduler tree node information from FW before adding it to
the driver's software database. This will keep the node information current
in driver.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously the comment stated that VSI lists should be used when a
second VSI becomes a subscriber to the "VLAN address". VSI lists
are always used for VLAN membership, so replace "VLAN address" with
"MAC address". Also note that VLAN(s) always use VSI list rules.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have MAX_FW_API_VER_BRANCH, MAX_FW_API_VER_MAJOR, and
MAX_FW_API_VER_MINOR that we use in ice_controlq.h to test when a
firmware version is newer than expected. This is currently tested by
comparing each field separately. Thus, we compare the branch field
against the MAX_FW_API_VER_BRANCH, and so forth.
This means that currently, if we suppose that the max firmware version
is defined as 0.2.1, i.e.
Then firmware 0.1.3 will fail to load. This is because the minor version
3 is greater than the max minor version 1.
This is not intuitive, because of the notion that increasing the major
firmware version to 2 should mean any firmware version with a major
version is less than 2 should be considered older than 2...
In order to allow both 0.2.1 and 0.1.3 to load, you would have to define
the "max" firmware version as 0.2.3.. It is possible that such
a firmware version doesn't even exist yet!
Fix this by replacing the current logic with an updated check that
behaves as follows:
First, we check the major version. If it is greater than the expected
version, then we prevent driver load. Additionally, a warning message is
logged to indicate to the system administrator that they need to update
their driver. This is now the only case where the driver will refuse to
load.
Second, if the major version is less than the expected version, we log
an information message indicating the NVM should be updated.
Third, if the major version is exact, we'll then check the minor
version. If the minor version is more than two versions less than
expected, we log an information message indicating the NVM should be
updated. If it is more than two versions greater than the expected
version, we log an information message that the driver should be
updated.
To support this, the ice_aq_ver_check function needs its signature
updated to pass the HW structure. Since we now pass this structure,
there is no need to pass the firmware API versions separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update branding strings and remove device ids 0x1594 and 0x1595.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Direct assignment is preferred over a memcpy()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When shutting down the controlqs, we check if they are initialized
before we shut them down and destroy the lock. This is important, as it
prevents attempts to access the lock of an already shutdown queue.
Unfortunately, we checked rq.head and sq.head as the value to determine
if the queue was initialized. This doesn't work, because head is not
reset when the queue is shutdown. In some flows, the adminq will have
already been shut down prior to calling ice_shutdown_all_ctrlqs. This
can result in a crash due to attempting to access the already destroyed
mutex.
Fix this by using rq.count and sq.count instead. Indeed, ice_shutdown_sq
and ice_shutdown_rq already indicate that this is the value we should be
using to determine of the queue was initialized.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The mvneta controller can handle speeds up to 2500Mbps on the SGMII
interface. This relies on serdes configuration, the lane must be
configured at 3.125Gbps and we can't use in-band autoneg at that speed.
The main issue when supporting that speed on this particular controller
is that the link partner can send ethernet frames with a shortened
preamble, which if not explicitly enabled in the controller will cause
unexpected behaviours.
This was tested on Armada 385, with the comphy configuration done in
bootloader.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival cleanup, list_move_tail will implement the same function that
list_del() + list_add_tail() will do. hence just replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival cleanup, list_move_tail will implement the same function that
list_del() + list_add_tail() will do. hence just replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-09-25
This series contains updates to i40e and xsk.
Mariusz fixes an issue where the VF link state was not being updated
properly when the PF is down or up. Also cleaned up the promiscuous
configuration during a VF reset.
Patryk simplifies the code a bit to use the variables for PF and HW that
are declared, rather than using the VSI pointers. Cleaned up the
message length parameter to several virtchnl functions, since it was not
being used (or needed).
Harshitha fixes two potential race conditions when trying to change VF
settings by creating a helper function to validate that the VF is
enabled and that the VSI is set up.
Sergey corrects a double "link down" message by putting in a check for
whether or not the link is up or going down.
Björn addresses an AF_XDP zero-copy issue that buffers passed
from userspace to the kernel was leaked when the hardware descriptor
ring was torn down. A zero-copy capable driver picks buffers off the
fill ring and places them on the hardware receive ring to be completed at
a later point when DMA is complete. Similar on the transmit side; The
driver picks buffers off the transmit ring and places them on the
transmit hardware ring.
In the typical flow, the receive buffer will be placed onto an receive
ring (completed to the user), and the transmit buffer will be placed on
the completion ring to notify the user that the transfer is done.
However, if the driver needs to tear down the hardware rings for some
reason (interface goes down, reconfiguration and such), the userspace
buffers cannot be leaked. They have to be reused or completed back to
userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When an AF_XDP UMEM is attached to any of the Rx rings, we disallow a
user to change the number of descriptors via e.g. "ethtool -G IFNAME".
Otherwise, the size of the stash/reuse queue can grow unbounded, which
would result in OOM or leaking userspace buffers.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Outstanding Rx descriptors are temporarily stored on a stash/reuse
queue. When/if the HW rings comes up again, entries from the stash are
used to re-populate the ring.
The latter required some restructuring of the allocation scheme for
the AF_XDP zero-copy implementation. There is now a fast, and a slow
allocation. The "fast allocation" is used from the fast-path and
obtains free buffers from the fill ring and the internal recycle
mechanism. The "slow allocation" is only used in ring setup, and
obtains buffers from the fill ring and the stash (if any).
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the zero-copy enabled XDP Tx ring is torn down, due to
configuration changes, outstanding frames on the hardware descriptor
ring are queued on the completion ring.
The completion ring has a back-pressure mechanism that will guarantee
that there is sufficient space on the ring.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
msglen parameter seems to be unused in several virtchnl function.
This patch removes it from signatures of those functions.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When isup is false meaning that interface is going to shut down
set new speed to 0 to avoid double 'NIC Link is Down' messages.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we are trying to change VF settings, it is possible for 2 race
conditions to happen. One, when the VF is created but not yet enabled.
Second, the VF is enabled but the VSI is still not created or not yet
re-created in the VF reset flow.
This patch introduces a helper function to validate that the VF is
enabled and that the VSI is set up. This patch also calls this
function from other functions which could get into these race conditions.
While we are poking around here, remove unnecessary parenthesis that
checkpatch was complaining about.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to slightly simplify the code use the variables for pf and hw
that are declared in i40e_set_mac function.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up promiscuous configuration when a VF reset occurs.
Previously the promiscuous mode settings were still there after the VF
driver removal.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This resolves an issue where the VF link state was not being updated
when the PF is down or up, and the VF link state would always show
that it is running.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B is
not detected on 64bit system.
The issue was observed when bootloader(u-boot) does not check macb
feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
by default. Then macb driver is reading DMACFG register back and only
adding 64bit dma configuration but not cleaning it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for pci_is_pcie() is redundant here because all
chip versions >=18 are PCIe only anyway. In addition use
dma_set_mask_and_coherent() instead of separate calls to
pci_set_dma_mask() and pci_set_consistent_dma_mask().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be slightly simplified by acking even events we're not
interested in. In addition add a comment making clear that the
read has no functional purpose and is just a PCI commit.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The networking core has a default watchdog timeout of 5s. I see no
need to define an own timeout of 6s which is basically the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the Rx flow hash key was a 5-tuple (IP src, IP dst,
IP nextproto, L4 src port, L4 dst port) fixed value that we
configured at probe.
Add support for configuring this hash key at runtime.
We support all standard header fields configurable through ethtool,
but cannot differentiate between flow types, so the same hash key
is applied regardless of protocol.
We also don't support the discard option.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
