Add a linkmode helper to set the flow control advertisement in an
ethtool linkmode mask according to the tx/rx capabilities. This
implementation is moved from phylib, and documented with an
analysis of its shortcomings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of helpers to resolve negotiated flow control. Two helpers
are provided:
- linkmode_resolve_pause() which takes the link partner and local
advertisements, and decodes whether we should enable TX or RX pause
at the MAC. This is useful outside of phylib, e.g. in phylink.
- phy_get_pause(), which returns the TX/RX enablement status for the
current negotiation results of the PHY.
This allows us to centralise the flow control resolution, rather than
spreading it around.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The information about the PHY attached to the PHYLINK instance is useful
but is missing the IRQ prints that phy_attached_info() adds.
phy_attached_info() is a bit long and it would not be possible to use
phylink_info() anyway.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a PHY node, register its time stamper, if any, and attach
the instance to the PHY device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two drivers and generic code which contain exactly the same
code to read the status of a PHY operating without autonegotiation
enabled. Rather than duplicate this code, provide a helper to read
this information.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for restarting autonegotiation(), similar to the clause 45
variant. Use it in __genphy_config_aneg()
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove initialisers that set .aneg_done to genphy_aneg_done - this is
the default for clause 22 PHYs, so the initialiser is redundant.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
"Unsupported (update phy-core.c)/Unsupported (update phy-core.c)"
when the speed and duplex settings are printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We currently match clause 45 PHYs using any ID read from a MMD marked
as present in the "Devices in package" registers 5 and 6. However,
this is incorrect. 45.2 says:
"The definition of the term package is vendor specific and could be
a chip, module, or other similar entity."
so a package could be more or less than the whole PHY - a PHY could be
made up of several modules instantiated onto a single chip such as the
Marvell 88x3310, or some of the MMDs could be disabled according to
chip configuration, such as the Broadcom 84881.
In the case of Broadcom 84881, the "Devices in package" registers
contain 0xc000009b, meaning that there is a PHYXS present in the
package, but all registers in MMD 4 return 0xffff. This leads to our
matching code incorrectly binding this PHY to one of our generic PHY
drivers.
This patch changes the way we determine whether to attempt to match a
MMD identifier, or use it to request a module - if the identifier is
all-ones, then we skip over it. When reading the identifiers, we
initialise phydev->c45_ids.device_ids to all-ones, only reading the
device ID if the "Devices in package" registers indicates we should.
This avoids the generic drivers incorrectly matching on a PHY ID of
0xffffffff.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for clause 37 1000Base-X auto-negotiation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the assignment to OR when dealing with phydev->dev_flags in
phy_attach_direct function, and this is to make sure dev_flags set in
driver's probe callback won't be lost.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move reading the link partner advertisement out of genphy_read_status()
into its own separate function. This will allow re-use of this code by
PHY drivers that are able to read the resolved status from the PHY.
Tested-by: tinywrkb <tinywrkb@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users have been removed we can remove genphy_config_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
__genphy_config_aneg that takes a parameter whether restarting
auto-negotiation is needed (depending on whether content of
vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
we can set non-C22 mode flags before.
Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using linkmode_adv_to_mii_adv_t and linkmode_adv_to_mii_ctrl1000_t
allows to simplify the code. In addition avoiding the conversion to
the legacy u32 advertisement format allows to remove the warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.
Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().
v2:
- patch added to series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A prerequisite for PHYLIB to work in the absence of a struct net_device
is to not access pointers to it.
Changes are needed in the following areas:
- Printing: In some places netdev_err was replaced with phydev_err.
- Incrementing reference count to the parent MDIO bus driver: If there
is no net device, then the reference count should definitely be
incremented since there is no chance that it was an Ethernet driver
who registered the MDIO bus.
- Sysfs links are not created in case there is no attached_dev.
- No netif_carrier_off is done if there is no attached_dev.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that wraps the operation of creating sysfs
links between the netdev->phydev and the phydev->attached_dev.
This is needed to keep the indentation level in check in a follow-up
patch where this function will be guarded against the existence of a
phydev->attached_dev.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a link mode for 100BaseT1, use it in
phy_basic_t1_features so T1 PHY drivers will indicate this mode via
the Ethtool API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.
See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes
The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering that in polling mode each link drop will be latched,
settings can't have changed if link was up and is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't set phydev->autoneg_complete in one exit path.
Fix this.
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_read_status() so far checks phydev->supported, not the actual
PHY capabilities. This can make a difference if the supported speeds
have been limited by of_set_phy_supported() or phy_set_max_speed().
It seems that this issue only affects the link partner advertisements
as displayed by ethtool. Also this patch wouldn't apply to older
kernels because linkmode bitmaps have been introduced recently.
Therefore net-next.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meanwhile we have generic functions for reading the abilities of
Clause 22 / 45 PHY's. This allows to use them as fallback in case
callback get_features isn't set. Benefit is the reduction of
boilerplate code in PHY drivers.
v2:
- adjust the comment in phy_driver_register to match the code
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't consider the case that autoneg process
finishes successfully but both link partners have no mode in common.
In this case there's no link, nevertheless we may be interested in
what the link partner advertised.
Like phydev->link we set phydev->autoneg_complete in
genphy_update_link() and use the stored value in genphy_read_status().
This way we don't have to read register BMSR again.
Fixes: b6163f194c ("net: phy: improve genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the genphy driver populates phydev->supported like this:
First all possible feature bits are set, then genphy_config_init()
reads the available features from the chip and remove all unsupported
features from phydev->supported. This can be simplified by using
genphy_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves few aspects of genphy_read_status():
- Don't initialize lpagb, it's not needed.
- Move initializing phydev->speed et al before the if clause.
- In auto-neg case, skip populating lp_advertising if we
don't have a link. This avoids quite some unnecessary
MDIO reads in case of phylib polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
