Now that we don't have hwmod entry for pcie PHY remove the
ti,hwmod property from PCIE PHY's. Otherwise we will get:
platform 4a094000.pciephy: Cannot lookup hwmod 'pcie1-phy'
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable the pm_runtime of the device upon remove. This is
added to balance the pm_runtime_enable() invoked in the probe.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The current OMAP dmtimer probe does not check for the return
status of pm_runtime_get_sync() before initializing the timer
registers. Any timer with missing hwmod data would return a
failure here, and the access of registers without enabling the
clocks for the timer would trigger a l3_noc interrupt and a
kernel boot hang. Add proper checking so that the probe would
return a failure graciously without hanging the kernel boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The family information in the soc-bus data is currently
not classified properly for AM33xx devices, and a read
of /sys/bus/soc/devices/soc0/family currently shows
"Unknown". Fix the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds missing dma DTS definitions for omap aes and sham drivers.
Without it kernel drivers do not work for device tree based booting
while it works for legacy booting on general purpose SoCs.
Note that further changes are still needed for high secure SoCs. But since
that never worked in legacy boot mode either, those will be sent separately.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
I upgraded my u-boot and noticed that wl12xx stopped working.
Turns out the kernel is not setting the quirk for the MMC2
copy clock while the eariler bootloader I had was setting it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HNIc
-----END PGP SIGNATURE-----
Merge tag 'for-v4.0-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.0/fixes
ARM: OMAP2+: first set of hwmod and PRCM fixes for v4.0-rc
This series fixes the following bugs:
- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
in the OMAP4 PRM code.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/
Enable TWL4030_USB which is used at least on Nokia N900/N950/N9 (OMAP3)
and BeagleBoard.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This was incorrectly reading the irq status registers during the save
and clear, instead of the irq enable. This worked because there is only
one user for the prcm interrupts currently, namely the io-chain. Whenever
the function was called, an io-chain interrupt was both pending and
enabled.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Deasserting hardreset increases the usecount for the hwmod parent clockdomain
always, however usecount is only decreased at end in certain error cases.
This causes software supervised clockdomains to remain always on, preventing
idle. Fixed by always releasing the hwmods clockdomain parent when exiting
the function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Carlos Hernandez <ceh@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fixed hwmod data for pcie by having the correct module mode offset.
Previously this module mode offset was part of pcie PHY which was wrong.
Now this module mode offset was moved to pcie hwmod and removed the hwmod data
for pcie phy. While at that renamed pcie_hwmod to pciess_hwmod in order
to match with the name given in TRM.
This helps to get rid of the following warning
"omap_hwmod: pcie1: _wait_target_disable failed"
[Grygorii.Strashko@linaro.org: Found the issue that actually caused
"omap_hwmod: pcie1: _wait_target_disable failed"]
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add struct lock_class_key to omap_hwmod struct and use it to set unique
lockdep class per hwmod.
This will ensure that lockdep will know that each omap_hwmod->_lock should
be treated as separate class and will not give false warning about deadlock
or other issues due to nested use of hwmods.
DRA7x's ATL hwmod is one example for this since McASP can select ATL clock
as functional clock, which will trigger nested oh->_lock usage. This will
trigger false warning from lockdep validator as it is dealing with classes
and for it all hwmod clocks are the same class.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The Kconfig options for the asm9260 timer is wrong as it can be selected by
another platform with allyes config and thus leading to a compilation failure
as some non arch related code is pulled by the compilation.
Fix this by having the platform Kconfig to select the timer as it is done for
the others drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Conflicts:
drivers/clocksource/Kconfig
Fixes: http://bugs.elinux.org/issues/127
the bb.org community was seeing random reboots before this change.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit 87517d26d8 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SATA operation depends on PIPE3 PHY and if we want
to boot from SATA drives, we have to have the PIPE3 PHY
driver built-in.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we have i2c0 sleep pinctrl state but were passing
default state anyhow. Fix that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This regulator is used on AM437x Industrial Development Kit.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As it turns out, tps62362 is actually on I2C bus0,
not bus1. This has gone unnoticed because Linux
doesn't use (as of now) that regulator at all, it's
setup by the bootloader and left as is.
While at that, also add missing reg property for
our regulator.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Offset for smc91x must be zero otherwise smc91x linux kernel driver does not
detect smc91x ethernet hardware in qemu N900 machine.
The 0x300 offset was used to supress a warning the smsc911x
driver produces about non-standard offset as 0x300 seems to
be the EEPROM default. As only three address lines are
connected both 0 and 0x300 will work just fine with 0 being
correct. The warning about the non-standard offset can be
fixed by writing to EEPROM as that's needed in any case to
set the MAC address.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[tony@atomide.com: updated comments, just use 0 instead of 0x0]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With legacy boot i2c buses on Nokia N900 are numbered i2c1, i2c2 and i2c3.
Commit 20b80942ef ("ARM: dts: OMAP3+: Add i2c aliases") fixed the
numbering with DT boot, but introduced a regression on N900 - aliases
become i2c0, i2c1 and i2c2. Fix that by providing the correct aliases in
the board dts.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: this is needed for legacy user space to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the USB completely because of an unconfigured USB phy, and
I only tested it to make sure the Mentor chips are detected and
clocked without a phy.
After testing the USB with actual devices I noticed a few issues
that should be fixed to avoid confusion:
- The USB id pin on dm8168-evm is hardwired and can be changed
only by software. As there are two USB-A type connectors, let's
start both in host mode instead of otg.
- The Mentor core is configured in such a way on dm8168-evm that
it's not capable of multipoint at least on revision c board
that I have.
- We need ranges for the syscon to properly set up the phy as
children of the SCM syscon area.
- Let's not disable the second interface, the board specific
dts files can do that if really needed. Most boards should
just keep it enabled to ensure the device is idled properly.
Note that also a phy and several musb fixes are still needed to
make the USB to work properly in addition to this fix.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM fix from Russell King:
"Just one fix this time around. __iommu_alloc_buffer() can cause a
BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or
__GFP_HIGHMEM set. The patch from Alexandre addresses this"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()
A few fixes that came in too late to make it into the first set of pull
requests but would still be nice to have in -rc1. The majority of these
are trivial build fixes for bugs that I found myself using randconfig
testing, and a set of two patches from Uwe to mark DT strings as 'const'
where appropriate, to resolve inconsistent section attributes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=hrfV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few fixes that came in too late to make it into the first set of
pull requests but would still be nice to have in -rc1.
The majority of these are trivial build fixes for bugs that I found
myself using randconfig testing, and a set of two patches from Uwe to
mark DT strings as 'const' where appropriate, to resolve inconsistent
section attributes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: make of_device_ids const
ARM: make arrays containing machine compatible strings const
ARM: mm: Remove Kconfig symbol CACHE_PL310
ARM: rockchip: force built-in regulator support for PM
ARM: mvebu: build armada375-smp code conditionally
ARM: sti: always enable RESET_CONTROLLER
ARM: rockchip: make rockchip_suspend_init conditional
ARM: ixp4xx: fix {in,out}s{bwl} data types
ARM: prima2: do not select SMP_ON_UP
ARM: at91: fix pm declarations
ARM: davinci: multi-soc kernels require AUTO_ZRELADDR
ARM: davinci: davinci_cfg_reg cannot be init
ARM: BCM: put back ARCH_MULTI_V7 dependency for mobile
ARM: vexpress: use ARM_CPU_SUSPEND if needed
ARM: dts: add I2C device nodes for Broadcom Cygnus
ARM: dts: BCM63xx: fix L2 cache properties
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
There doesn't seem to be any valid reason to allocate the pages array
with the same flags as the buffer itself. Doing so can eventually lead
to the following safeguard in mm/slab.c's cache_grow() to be hit:
if (unlikely(flags & GFP_SLAB_BUG_MASK)) {
pr_emerg("gfp: %un", flags & GFP_SLAB_BUG_MASK);
BUG();
}
This happens when buffers are allocated with __GFP_DMA32 or
__GFP_HIGHMEM.
Fix this by allocating the pages array with GFP_KERNEL to follow what is
done elsewhere in this file. Using GFP_KERNEL in __iommu_alloc_buffer()
is safe because atomic allocations are handled by __iommu_alloc_atomic().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const structs in arch/arm as const, too.
While at it also add some __initconst annotations.
Acked-by: Jason Cooper <jason@lakedameon.net>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The definition
static const char *axxia_dt_match[] __initconst = {
...
defines a changable array of constant strings. That is you must not do:
*axxia_dt_match[0] = 'k';
but
axxia_dt_match[0] = "different string";
is fine. So the annotation __initconst is wrong and yields a compiler
error when other really const variables are added with __initconst.
As the struct machine_desc member dt_compat is declared as
const char *const *dt_compat;
making the arrays const is the better alternative over changing all
annotations to __initdata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Like in 3.19, I once more have a multi-stage cleanup for one asm-generic
header file, this time the work was done by Michael Tsirkin and cleans
up the uaccess.h file in asm-generic, as well as all architectures for
which the respective maintainers did not pick up his patches directly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVONFpmCrR//JCVInAQIoYRAA1T3ID1bQLqdi8TU1X+vzutXzGFRhRFii
u18GYeN6sGTcfqQD0GsNSaH7G8XehF3cgJ9eo4h9YkRPIG/0T0FO+dqdB0uRh8iy
GKcUqVhgvCFpOBDUJC6FgMvgWWyVrgSUBqG6qSXck/PDcMSsUa/m/GcLhR/sHWGn
EGEAzYNvJgdOaJ1z0vfPFK6mPwFwmYzIss5XFuoBAKKN856fBlxofkQqdpKjGDFH
n0UziaJ5tbCdlZ9M9Y5JN9RU8yBCcOmGHnHUAQHz3BXOt9sD7o5jDuzsUbj+vUGJ
gzNc8kee9Pyy8ZA1F959gspaxe5Oumq7NLgs3HDjK6ZDRKpJvZb6iXi56f15chlZ
dItTbFSxCHOFs0d8XJKNbmPt44pJ/qKO+03lMIGttMkIm7hXfvyMWSPZV9G0Pu1y
zbWEDgW2Mdrdt0saNSD46IEp+c7E5P3D9JSctQRdQjReoCbOHwqrSHi1Zeg97XL4
I1E0KwDqFUw3P1dXr5ahXmR50ZigBGjN5Fz3N7GmJt2x4PRSS2Sw92hyCrL0YM8J
56FdRA7UJ0V/SzmAko3F5wWmhabc6L+qrVA42R6U3SNSjU8hwppOkYKDINNhPZfL
SGy1oQS6Jj10WxLOVp66NC7XxXzBybDcQnatz4XtNN8P5sfekUGSGBeMyMsHl7IJ
9MT3xym+DWU=
=LROx
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic uaccess.h cleanup from Arnd Bergmann:
"Like in 3.19, I once more have a multi-stage cleanup for one
asm-generic header file, this time the work was done by Michael
Tsirkin and cleans up the uaccess.h file in asm-generic, as well as
all architectures for which the respective maintainers did not pick up
his patches directly"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (37 commits)
sparc32: nocheck uaccess coding style tweaks
sparc64: nocheck uaccess coding style tweaks
xtensa: macro whitespace fixes
sh: macro whitespace fixes
parisc: macro whitespace fixes
m68k: macro whitespace fixes
m32r: macro whitespace fixes
frv: macro whitespace fixes
cris: macro whitespace fixes
avr32: macro whitespace fixes
arm64: macro whitespace fixes
arm: macro whitespace fixes
alpha: macro whitespace fixes
blackfin: macro whitespace fixes
sparc64: uaccess_64 macro whitespace fixes
sparc32: uaccess_32 macro whitespace fixes
avr32: whitespace fix
sh: fix put_user sparse errors
metag: fix put_user sparse errors
ia64: fix put_user sparse errors
...
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
Commit 20e783e39e ("ARM: 8296/1: cache-l2x0: clean up aurora cache
handling") removed the only user of the Kconfig symbol CACHE_PL310.
Setting CACHE_PL310 is now pointless. Remove its Kconfig entry, and one
select of this symbol.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
