The thermal core restricts names of thermal zones to under 20
characters. Fix the names for a couple of msm8998 thermal zones.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Andy Gross <agross@kernel.org>
msm8998 has 22 sensors connected in total, 14 on the 1st controller, 8
on the 2nd controller. Increase the number to allow sensors with ID 12
and 13 to be registered.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Andy Gross <agross@kernel.org>
The msm8998-mtp doesn't have TSENS-based sensors wired up for skin and
battery thermal zones. TSENS sensors should be common across all boards
using the SoC and shouldn't be board-specific as these entries.
They also show the following error when trying to read the temperature
cat: read error: Invalid argument
Remove these board-specific erroneous thermal zones.
Fixes: 4449b6f248 ("arm64: dts: qcom: msm8998: Add tsens and thermal-zones")
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Andy Gross <agross@kernel.org>
This patch adds support both digital and analog audio on DB820c.
This board has HDMI port and 3.5mm audio jack to support both digital
and analog audio respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The APQ8096 DB820c platform provides HDMI output. The MDSS block on
8x96 supports a direct HDMI out. Populate the MDSS, MDP and HDMI DT
nodes. Also, add the HDMI HPD and DDC pinctrl nodes with the bias
and driver strength specified for this platform.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add an initial node for the Adreno GPU.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Specify the relative CPU capacity of all SDM845 AP cores.
The values were provided by Qualcomm engineers.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The 8 CPU cores of the SDM845 are organized in two clusters of 4 big
("gold") and 4 little ("silver") cores. Add a cpu-map node to the DT
that describes this topology.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add 'bi_tcxo' as ref clock for the DSI PHYs, it was previously
hardcoded in the PLL 'driver' for the 10nm PHY.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add 'xo_board' as ref clock for the DSI PHYs, it was previously
hardcoded in the PLL 'driver' for the 28nm PHY.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The temperature information from the temp-alarm block itself is very
coarse ("temperature is above/below trip points"). Provide the driver
with the die temperature channel of the ADC on the PMIC for more precise
readings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the Audio DSP (ADSP) and Compute DSP (CDSP) nodes for TrustZone
based remoteproc, supporting booting these cores on e.g. the MTP, and
enable the same for the MTP.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Define the rmtfs memory node. As the memory region specified in version
10 of the memory map is only 1MB a chunk of unallocated memory is
chosen.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Update existing and add missing regions to the reserved memory map, as
described in version 10.
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Wire up the reset controller in the Qcom UFS controller for the PHY.
This will be used to toggle PHY reset during initialization of the PHY.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
blsp1_i2c1 is at 0x0c175000
blsp2_i2c5 is at 0x0c1ba000 (the label is correct)
Fixes: 1e71d0c273 ("arm64: dts: qcom: msm8998: Enumerate i2c controllers")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The compatible flag should be different for each board to match
with the dtb and to let the bootloader pick the appropriate dtb.
Signed-off-by: Khasim Syed Mohammed <khasim.mohammed@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
This adds the gpio-ranges property so that the GPIO pins are initialized
by the GPIO framework and not pinctrl. This fixes a circular dependency
between these two frameworks so GPIO hogging can be used on this board.
This was not tested on this particular hardware, however this same
change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <agross@kernel.org>
This adds the gpio-ranges property so that the GPIO pins are initialized
by the GPIO framework and not pinctrl. This fixes a circular dependency
between these two frameworks so GPIO hogging can be used on this board.
This was not tested on this particular hardware, however this same
change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <agross@kernel.org>
This adds the gpio-ranges property so that the GPIO pins are initialized
by the GPIO framework and not pinctrl. This fixes a circular dependency
between these two frameworks so GPIO hogging can be used on this board.
This was not tested on this particular hardware, however this same
change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <agross@kernel.org>
This adds the gpio-ranges property so that the GPIO pins are initialized
by the GPIO framework and not pinctrl. This fixes a circular dependency
between these two frameworks so GPIO hogging can be used on this board.
This was not tested on this particular hardware, however this same
change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <agross@kernel.org>
We don't have any cooling-devices related to the camera. Use the "hot"
trip type so allow the temperature to be exported to userspace and
remove the "critical" trip.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Maintain naming consistency with what was landed for sdm845. Simplifies
parsing for test tools.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Maintain naming consistency with what was landed for sdm845. Simplifies
parsing for test tools.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Maintain naming consistency with what was landed for sdm845. Simplifies
parsing for test tools.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
sdm845 has a total of 21 temperature sensors. Populate DT with
information about them.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
msm8998 has a total of 22 temperature sensors. Populate DT with
information about them.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The first sensor is on top and the second sensor below the GPU
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The GPU sensor is sensor ID 13 on controller 0
Fixes: 4449b6f248 ("arm64: dts: qcom: msm8998: Add tsens and thermal-zones")
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The silver cluster (typically cpu0-3) are monitored by sensor IDs 1-3 on
tsens controller 0. The gold cluster (typically cpu4-7) are monitored by
sensor IDs 7-10 on tsens controller 0.
Fixes: 4449b6f248 ("arm64: dts: qcom: msm8998: Add tsens and thermal-zones")
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
msm8996 has a total of 21 temperature sensors. Populate DT with
information about them.
There are 2 sensors on each of the cpus - one on the top, the other
below (we only expose one on the top in DT for now). For the GPU, we
expose both, the one on the top and the one below.
Depending on the version of the silicon, sensor 2 is either placed near
the L3 cache or the venus video decoder. It would've been nice to be
able to be version-specific but we don't have DTs that differentiate the
two versions of silicon yet.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
On platforms that have a modem, sensor 0 monitors the modem.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
efficiency comes from downstream. The valid upstream property is
capacity-dmips-mhz but until we can come up with those numbers, remove
this property.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
We've earlier added support to split the register address space into TM
and SROT regions. Split up the regmap address space into two for msm8998
that has a similar register layout.
The order is important (TM before SROT) because we make an assumption
that SROT is always the second address space in order to support legacy
DTs.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
In order to fix dependencies with rpmpd DT entries, the header was
dropped and hardcoded values were added for opp-level, during the
previous merge window.
Add the header back in now and remove the hardcodings, effectively
reverting commit '08585d21de9875a6064b350957faa0460a4c69a6: arm64: dts:
sdm845: Fixup dependency on RPMPD includes'
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable blsp1_uart3, define its pinconf and add the bluetooth node.
It seems provisioning is lacking a valid BD address, preventing the
interface from initializing, so provide a dummy for now.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add host controller and PHY DT nodes.
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The UFS host controller driver needs to set the load on 3 power rails
(l20, l26, s4) but the operation fails silently unless we specify the
regulator-allow-set-load property in the corresponding DT nodes.
Tested-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The property controlled-remotely should not be set by default
for qcs-404 device, it should be set based on the secure boot
options (TZ or ATF) preferred by the platform. Hence, the
controlled-remotely property is moved to platform specific
dts files.
Signed-off-by: Khasim Syed Mohammed <khasim.mohammed@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Include the device tree header for the on-chip interconnect endpoint
resources on sdm845 devices. This will allow using the "interconnects"
property in DT nodes to describe the interconnect path resources they use.
The sdm845 interconnect provider DT node is already present, but the
header file with the resources is not included, so let's fix this.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
