Add the RTS/CTS property for auart0 which means we enable the
DMA support for it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These systems all use saif0 as the mclock provider to codec sgtl5000.
Reflect that in device tree source, so that sgtl5000 can find the clock
by calling clk_get().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of using a custom binding for retrieving the GPIO that activates the
LCD from devicetree, use a standard regulator.
This approach has the advantage to be more generic.
For example: in the case of a board that has a PMIC supplying the LCD voltage,
the current approach would not work, as it only searches for a GPIO pin.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.12: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx28evk has a free slot U50 that can be used to populate an I2C EEPROM.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx28evk has a free slot (J89) which can be used to populate an SPI NOR Flash.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
hog_pins is used to setup the pin functions, and it is not neccesarily used only
for GPIO pins, so use only 'hog' to describe a more generic term.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The presence and muxing of lcdif control pins can vary much on different
boards. Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.
Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand. Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts. Make this explicit by removing "okay" status.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
add gpmi-nand device tree support.
add gpmi-nand pinctrl support.
Also enable the gpmi support for mx28-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch includes basic dt support which can boot via nfs rootfs.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
