Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies. Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
http://bugzilla.kernel.org/show_bug.cgi?id=12239
The image writing code dropped a reference to the current swap device.
This doesn't show up if the hibernation succeeds - because it doesn't
affect the image which gets resumed. But it means multiple _failed_
hibernations end up freeing the swap device while it is still use!
swsusp_write() finds the block device for the swap file using swap_type_of().
It then uses blkdev_get() / blkdev_put() to open and close the block device.
Unfortunately, blkdev_get() assumes ownership of the inode of the block_device
passed to it. So blkdev_put() calls iput() on the inode. This is by design
and other callers expect this behaviour. The fix is for swap_type_of() to take
a reference on the inode using bdget().
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the resume code does not currently wait for device probing to finish.
Even without async function calls this is dicey and not correct,
but with async function calls during the boot sequence this is going
to get hit more...
This patch adds the synchronization using the newly introduced helper.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
there's a few places that currently loop over driver_probe_done(), and
I'm about to add another one. This patch abstracts it into a helper
to reduce duplication.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On hardware like the T61 it can take a couple of seconds for the battery
to start charging after the power is connected, and we incorrectly tell
userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either
the last full charge, or the design charge.
http://bugzilla.kernel.org/show_bug.cgi?id=12632
Signed-off-by: Richard Hughes <hughsient@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix multiuser mounts so server does not invalidate earlier security contexts
[CIFS] improve posix semantics of file create
[CIFS] Fix oops in cifs_strfromUCS_le mounting to servers which do not specify their OS
cifs: posix fill in inode needed by posix open
cifs: properly handle case where CIFSGetSrvInodeNumber fails
cifs: refactor new_inode() calls and inode initialization
[CIFS] Prevent OOPs when mounting with remote prefixpath.
[CIFS] ipv6_addr_equal for address comparison
The current implementation of the TX software time stamping fallback is
faulty because it accesses the skb after ndo_start_xmit() returns
successfully. This patch removes the fallback, which fixes kernel panics
seen during stress tests. Hardware time stamping is not affected by this
removal.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Bug fix on UP
Checkin 6ec68bff3c:
x86, mce: reinitialize per cpu features on resume
introduced a call to mce_cpu_features() in the resume path, in order
for the MCE machinery to get properly reinitialized after a resume.
However, this function (and its successors) was flagged __cpuinit,
which becomes __init on UP configurations (on SMP suspend/resume
requires CPU hotplug and so this would not be seen.)
Remove the offending __cpuinit annotations for mce_cpu_features() and
its successor functions.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When two different users mount the same Windows 2003 Server share using CIFS,
the first session mounted can be invalidated. Some servers invalidate the first
smb session when a second similar user (e.g. two users who get mapped by server to "guest")
authenticates an smb session from the same client.
By making sure that we set the 2nd and subsequent vc numbers to nonzero values,
this ensures that we will not have this problem.
Fixes Samba bug 6004, problem description follows:
How to reproduce:
- configure an "open share" (full permissions to Guest user) on Windows 2003
Server (I couldn't reproduce the problem with Samba server or Windows older
than 2003)
- mount the share twice with different users who will be authenticated as guest.
noacl,noperm,user=john,dir_mode=0700,domain=DOMAIN,rw
noacl,noperm,user=jeff,dir_mode=0700,domain=DOMAIN,rw
Result:
- just the mount point mounted last is accessible:
Signed-off-by: Steve French <sfrench@us.ibm.com>
Samba server added support for a new posix open/create/mkdir operation
a year or so ago, and we added support to cifs for mkdir to use it,
but had not added the corresponding code to file create.
The following patch helps improve the performance of the cifs create
path (to Samba and servers which support the cifs posix protocol
extensions). Using Connectathon basic test1, with 2000 files, the
performance improved about 15%, and also helped reduce network traffic
(17% fewer SMBs sent over the wire) due to saving a network round trip
for the SetPathInfo on every file create.
It should also help the semantics (and probably the performance) of
write (e.g. when posix byte range locks are on the file) on file
handles opened with posix create, and adds support for a few flags
which would have to be ignored otherwise.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Fixes kernel bug #10451http://bugzilla.kernel.org/show_bug.cgi?id=10451
Certain NAS appliances do not set the operating system or network operating system
fields in the session setup response on the wire. cifs was oopsing on the unexpected
zero length response fields (when trying to null terminate a zero length field).
This fixes the oops.
Acked-by: Jeff Layton <jlayton@redhat.com>
CC: stable <stable@kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
...if it does then we pass a pointer to an unintialized variable for
the inode number to cifs_new_inode. Have it pass a NULL pointer instead.
Also tweak the function prototypes to reduce the amount of casting.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Move new inode creation into a separate routine and refactor the
callers to take advantage of it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Fixes OOPs with message 'kernel BUG at fs/cifs/cifs_dfs_ref.c:274!'.
Checks if the prefixpath in an accesible while we are still in cifs_mount
and fails with reporting a error if we can't access the prefixpath
Should fix Samba bugs 6086 and 5861 and kernel bug 12192
Signed-off-by: Igor Mammedov <niallain@gmail.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (26 commits)
drm/radeon: update sarea copies of last_ variables on resume.
drm/i915: Keep refs on the object over the lifetime of vmas for GTT mmap.
drm/i915: take struct mutex around fb unref
drm: Use spread spectrum when the bios tells us it's ok.
drm: Collapse identical i8xx_clock() and i9xx_clock().
drm: Bring PLL limits in sync with DDX values.
drm: Add locking around cursor gem operations.
drm: Propagate failure from setting crtc base.
drm: Check for a NULL encoder when reverting on error path
drm/i915: Cleanup the hws on ringbuffer constrution failure.
drm/i915: Don't add panel_fixed_mode to the probed modes list at LVDS init.
drm: Release user fbs in drm_release
drm/i915: Unpin the fb on error during construction.
drm/i915: Unpin the hws if we fail to kmap.
drm/i915: Unpin the ringbuffer if we fail to ioremap it.
drm/i915: unpin for an invalid memory domain.
drm/i915: Release and unlock on mmap_gtt error path.
drm/i915: Set framebuffer alignment based upon the fence constraints.
drm: Do not leak a new reference for flink() on an existing name
drm/i915: Fix potential AB-BA deadlock in i915_gem_execbuffer()
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: use the right protections for split-up pagetables
x86, vmi: TSC going backwards check in vmi clocksource
Intel 8257x Ethernet boards have a feature called Serial Over Lan.
This feature works by emulating a serial port, and it is detected by
kernel as a normal 8250 port. However, this emulation is not perfect, as
also noticed on changeset 7500b1f602.
Before this patch, the kernel were trying to check if the serial TX is
capable of work using IRQ's.
This were done with a code similar this:
serial_outp(up, UART_IER, UART_IER_THRI);
lsr = serial_in(up, UART_LSR);
iir = serial_in(up, UART_IIR);
serial_outp(up, UART_IER, 0);
if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
up->bugs |= UART_BUG_TXEN;
This works fine for other 8250 ports, but, on 8250-emulated SoL port, the
chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register.
Due to that, UART_BUG_TXEN is sometimes enabled. However, as TX IRQ keeps
working, and the TX polling is now enabled, the driver miss-interprets the
IRQ received later, hanging up the machine until a key is pressed at the
serial console.
This is the 6 version of this patch. Previous versions were trying to
introduce a large enough delay between serial_outp and serial_in(up,
UART_IIR), but not taking forever. However, the needed delay couldn't be
safely determined.
At the experimental tests, a delay of 1us solves most of the cases, but
still hangs sometimes. Increasing the delay to 5us was better, but still
doesn't solve. A very high delay of 50 ms seemed to work every time.
However, poking around with delays and pray for it to be enough doesn't
seem to be a good approach, even for a quirk.
So, instead of playing with random large arbitrary delays, let's just
disable UART_BUG_TXEN for all SoL ports.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds more documentation of the lowlevel API to avoid future bugs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: proper vcache flush on unmap_kernel_range()
flush_cache_vunmap() should be called before pages are unmapped. Add
a call to it in unmap_kernel_range().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed the old commit 8f5aa26c75
("cpusets: update_cpumask documentation fix") is not a complete fix,
resulting in inconsistent paragraphs. This patch fixes it and does other
fixes and updates:
- s/migrate_all_tasks()/migrate_live_tasks()/
- describe more cpuset control files
- s/cpumask_t/struct cpumask/
- document cpu hotplug and change of 'sched_relax_domain_level' may cause
domain rebuild
- document various ways to query and modify cpusets
- the equivalent of "mount -t cpuset" is "mount -t cgroup -o cpuset,noprefix"
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BUILD_DOCSRC should be controlled by "config" instead of "menuconfig".
I have no idea how I managed to use "menuconfig" here.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "break" would just result in reusing a free'd pointer. I don't have
the cards myself to test it though. :/
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Caused by 736d54533a (sx.c: fix missed unlock_kernel() on error path in
sx_fw_ioctl()). You guys keep breaking things this way in every single
kernel release in at least couple of places... :-(
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It should be Documentation/build/kconfig.txt.
Introduced by commit 2af238e455
("kbuild: make *config usage docs").
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kzfree() is a wrapper for kfree() that additionally zeroes the underlying
memory before releasing it to the slab allocator.
Currently there is code which memset()s the memory region of an object
before releasing it back to the slab allocator to make sure
security-sensitive data are really zeroed out after use.
These callsites can then just use kzfree() which saves some code, makes
users greppable and allows for a stupid destructor that isn't necessarily
aware of the actual object size.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
oprofile for MN10300 seems to have been broken by the advent of the new
tracing framework.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds NETLINK_BROADCAST_ERROR which is a netlink
socket option that the listener can set to make netlink_broadcast()
return errors in the delivery to the caller. This option is useful
if the caller of netlink_broadcast() do something with the result
of the message delivery, like in ctnetlink where it drops a network
packet if the event delivery failed, this is used to enable reliable
logging and state-synchronization. If this socket option is not set,
netlink_broadcast() only reports ESRCH errors and silently ignore
ENOBUFS errors, which is what most netlink_broadcast() callers
should do.
This socket option is based on a suggestion from Patrick McHardy.
Patrick McHardy can exchange this patch for a beer from me ;).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix isdn/sc/shmem.c printk format warning:
drivers/isdn/sc/shmem.c:57: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix decrement timeouts will reach -1 rather than 0, so
the error path does not appear.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing set_bit() to disable data transfer when a memchange
notification is handled
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool.h says the driver should set the magic field in get_eeprom and
verify it in set_eeprom. This patch adds this functionality using an
arbitary driver-specific magic value constant (0x9420).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin recently fixed several instances where variables reach -1,
but 0 is tested afterwards. This patch fixes another, so the timeout
will be correctly detected and a warning printed.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a one liner change to have the driver use by default the v1.4
of the i2400m firmware instead of v1.3. The v1.4 version of the
firmware has been submitted to David Woodhouse for inclusion in the
linux-firmware tree and it is already available at
http://linuxwimax.org/Download.
The reason for this change is that the 1.3 release of the user space
software and firmware has a few issues that will make it difficult to
use with currently deployed commercial networks such as Xohm and
Clearwire.
As well, the new 1.4 release of the user space software (which matches
the 1.4 firmware) has intermitent issues with the 1.3 firmware.
The 1.4 release in http://linuxwimax.org/Download has been widely
deployed and tested with the codebase in 2.6.29-rc, the 1.4 firmware
and the 1.4 user space components.
We understand it is quite late in the rc process for such a change,
but would like to ask for the change to be taken into consideration.
Alternatively, a user could always force feed a 1.4 firmware into a
driver that doesn't have this modification by:
$ cd /lib/firmware
$ mv i2400m-fw-usb-1.3.sbcf i2400m-fw-usb-1.3.real.sbcf
$ ln -sf i2400m-fw-usb-1.4.sbc i2400m-fw-usb-1.3.sbcf
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code adds a module parameter called num_vfs which defines if the
driver should attempt to use sr-iov and if so how many VFs should be
enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support to handle requests from the VF to perform
operations such as completing resets, setting/reading mac address, adding
vlans, adding multicast addresses, setting rlpml, and general
communications between the PF and all VFs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the pf portion of vmdq support. This provides enough support so that
VMDq is enabled, and the pf is functional without enabling vfs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
