We now initialise the PCM driver through the MSP DAI, so there is
no need to register it though platform code anymore. This patch
strips out all PCM platform registration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
GPIO numbers for the newly created gpio-regulator will differ from
board to board. Therefore it's not sensible to leave this information
in the top level DTSI file. Let's move them out to the DTS files
where they can correctly vary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Not all supported boards will require a MMCI gpio-regulator,
therefore it's a good idea to only enable the node when and if
it is required. Let's disable it by default.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
UARTs no longer require call-back information, since the reset
call-back was removed in 43b5f0d692.
The only AUXDATA dependencies remaining for UARTs are DMA settings.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the 3 UART nodes required to enable serial ports on the u9540.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Device Tree machine description for the ux5x0 was moved
recently and as a consequence missed the addition of SMP
operations. Without this patch SMP doesn't work and only one
CPU is present after booting.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is the intention to convert the MMC voltage changing from
GPIO flipping to using a proper GPIO regulator interface. A
prerequisite of that is to enable the GPIO regulator
functionality. As this affects all ux5x0 based boards we'll
do it here instead of in the Kconfigs.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On boot the Nomadik GPIO controller complains that an IRQ can't be
configured as active high level-sensitive, so this patch converts
it to be low-to-high edge triggered instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a very simple mechanism to change and SDI's voltage which
consists of toggling some GPIOs. This scenario can be better handled
if we convert it to a GPIO regulator. This patch provides one which
can be read from Device Tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
So far, each ST-Ericsson board supported by Device Tree has been similar
enough to run though a single DT_MACHINE_INIT call. On the back of that
it has been suggested that we should reduce the number of compatible
strings in our dt_compat structure. After subsequent discussion with Arnd
Bergmann the conclusion was to list entries by platform as opposed to by
board.
The other suggestion was to use a single string which would cover all
supported platforms, but any wildcard entries would include unsupported
chipsets, such as the u5500 and potential new chips which no not yet have
DT functionality. Hence, the best solution which encompasses all supported
platforms, but no unsupported ones was to list the currently enabled four
chipsets; u8500, u8540, u9500 and u9540 instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The u8500 and u9540 DT_MACHINE_START calls are almost identical
at the moment, referencing exactly the same function pointers.
Until this changes we may as well convert the original one to
be more generic and use that instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When enabling ST-Ericsson's ccu9540 development board the board's
full name has not been used. This patch adapts all references of
the board's short name to how it should be referenced.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the 3 UART nodes required to enable serial ports on the u9540.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'st-ericsson,u8500' is too much of a broad name to be used for
any of the supported development boards supported by ST-Ericsson.
As such it was never used. It has no place to remain in the board
compatible list, hence why it's being removed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch allows the STMPE keypad driver to be successfully probed
and initialised during a Device Tree enabled boot sequence. It
contains all of the required properties needed to setup and map
each key on the 6x3 keypad located on the ST User Interface Board.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we apply the STMPE Multi-Functional Device's node to the
ST User Interface Board Device Tree file. It includes all of
the properties required for correct device initialsation.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regulator_has_full_constraints() call is not required if we
are booting with Device Tree as it's assumed in this case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible to connect a BU21013 Touch Screen to all version
of the HREF which support the ST-UIB. This patch applies all the
necessary settings to the pre-v60 and v60+ HREF Device Trees.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As there will be a Device Tree created for the UIBs, there is no
need to call the UIB initiation functions. Each device will be
detailed and registered from the Device Tree instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a skeleton creation which will be populated with the devices
found on one of ST-Ericsson's (UIB) User Interface Board.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We're currently carrying two 'struct bu21013_platform_device's which
are identical for no apparent reason. Here we remove the extra burden
and apply the same information to the two different instances of the
bu21012_tp driver registration.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To aid the kernel in its effort to move to DT only booting, we're
transplanting all Device Tree related code to cpu-db8500 which will
remain persistent throughout the transition. This change paths the
way for complete removal of board-mop500, which will be done once
the all DMA settings are moved into the respective DT source files.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Most devices have now been successfully DT:ed and each supported
platform has its own Device Tree source file. Hence the majority
of the platform specific device registration calls can now be
successfully removed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we ensure the SFH7741 Proximity Sensor is registered through
gpio-keys when booting with Device Tree enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In ux500 platform code we currently support a number of devices.
Two of these devices are fairly similar, but have key differences.
Early (pre-v60) HREFs and the more up-to-date versions (v60+), and
they both need to be supported by Device Tree. Here we apply a DT
source file for the earlier versions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are two main versions of the ST-Ericsson hardware reference board,
each with subtle differences. These versions are described in current
platform data as 'mop500' for HREF v1.1 & v2.0 and 'hrefv60+' for latter
incarnations. However, the boards have much in common, so this patch
creates a .dtsi (Device Tree Source Include) file which describes the
similarities between the two boards and individual 'hrefprev60' and
'hrefv60plus' .dts files which depict the differences.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Snowball's external SD/MMC slot is only capable of 4 bit data
transfer, not 8 bits as previously thought. This is a simple
fixup moving to the correct settings.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the DB8500 Reference Manual SDI devices are described as being
part of peripheral blocks. This is more in line with how these devices
are actually represented in hardware, so here we detail which
peripheral block each of the SDI devices belong in the node name.
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An earlier change prevented User Interface Boards (UIBs) from being
initialised on boards which did not support them. This change had
the undesired effect of reordering the UIB initialisation calls with
I2C registration. Here we ensure UIBs are only setup after all
required infrastructure is already in place.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we
had a few of these patches cause regressions themselves and had to
work out how to deal with those in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IDdm
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
This reverts commit 92063cee11, it
was applied prematurely, causing this build error for
imx_v4_v5_defconfig:
arch/arm/mach-imx/clk-imx25.c: In function 'mx25_clocks_init':
arch/arm/mach-imx/clk-imx25.c:206:26: error: 'pwm_ipg_per' undeclared (first use in this function)
arch/arm/mach-imx/clk-imx25.c:206:26: note: each undeclared identifier is reported only once for each function it appears in
Sascha Hauer explains:
> There are several gates missing in clk-imx25.c. I have a patch which
> adds support for them and I seem to have missed that the above depends
> on it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the introduction of CONFIG_ARCH_MULTIPLATFORM, versatile is
no longer the default platform, so we need to enable
CONFIG_ARCH_VERSATILE explicitly in order for that to be selected
rather than the multiplatform configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The split of 370 and XP into two Kconfig options and the multiplatform
kernel support has changed a few Kconfig symbols, so let's update the
mvebu_defconfig file with the latest changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
patch 738a0fd7 "ARM: at91: fix external interrupts in non-DT case"
fixed a run-time error on some at91 platforms but did not apply
the same change to at91x40, which now doesn't build.
This changes at91x40 in the same way that the other platforms
were changed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Here is one patch, a revert of a omap serial driver patch that was causing
problems, for your 3.7-rc tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCKwvoACgkQMUfUDdst+ymoNACeKWk+71cE4eNIDm72ZXI1W+Vr
IKwAn1ucM5516OgesMlNrQ6tiKQFWo6M
=4ou2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fix from Greg Kroah-Hartman:
"Here is one patch, a revert of a omap serial driver patch that was
causing problems, for your 3.7-rc tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: omap: fix software flow control"
From Kukjin Kim <kgene.kim@samsung.com>:
One is spi stuff for fix the device names for the different subtypes of
the spi controller. And the other is adding missing .smp field for
exynos4-dt and fixing memory sections for exynos4210-trats board.
* 'v3.7-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set .smp field of machine descriptor for exynos4-dt
ARM: dts: Split memory into 4 sections for exynos4210-trats
ARM: SAMSUNG: Add naming of s3c64xx-spi devices
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit 871ae57adc, which is
scheduled for v3.8 and accidently got into v3.7-rc series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
