When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf2 ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@al
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime suspend issues result from the linking change.
Case 1:
a) link down occurs.
b) driver disable tx/rx.
c) autosuspend occurs.
d) hw linking up.
e) device suspends without enabling tx/rx.
f) couldn't wake up when receiving packets.
Case 2:
a) Nway results in linking down.
b) autosuspend occurs.
c) device suspends.
d) device may not wake up when linking up.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then,
according to the value of DRIVER_VERSION, we could know which
patches are used generally without comparing the source code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust napi_disable() and napi_enable() to avoid r8152_poll() start
working before rx ready. Otherwise, it may have race condition for
rx_agg.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the driver to enable WOL if the device doesn't support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Disable U1/U2 during initialization.
- Disable lpm when linking is on, and enable it when linking is off.
- Disable U1/U2 when enabling runtime suspend.
It is possible to let hw stop working, if the U1/U2 request occurs
during some situations. The patch is used to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Zheng Liu <zhliu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.
Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().
Set the default timeout value according to the USB speed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a capability which let the hw could change the settings
automatically when the power change to ON. However, the USB reset
would reset the settings to the hw default, so the driver has to
restore the relative settings. Otherwise, it would influence the
functions of the hw, and the compatibility for the USB hub and
USB host controller.
The relative settings are as following.
- set the power down scale to 96.
- enable the power saving function of USB 2.0.
- disable the ALDPS of ECM mode.
- set burst mode depending on the burst size.
- enable the flow control of endpoint full.
- set fifo empty boundary to 32448 bytes.
- enable the function of exiting LPM when Rx OK occurs.
- set the connect timer to 1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_get_protocol() has been defined and use it to replace
get_protocol().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the
same line.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to accress the hw register if the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tasklet with NAPI.
Add rx_queue to queue the remaining rx packets if the number of the
rx packets is more than the request from poll().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't submit the rx if the device is unplugged, stopped, or
linking down.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rtl_start_rx() from rtl_enable() and put it after calling
netif_carrier_on().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support ndo_features_check to avoid:
- the transport offset is more than the hw limitation when using hw checksum.
- the skb->len of a GSO packet is more than the limitation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine REALTEK_USB_DEVICE for the desired USB interface for probe().
There are three USB interfaces for the device. USB_CLASS_COMM and
USB_CLASS_CDC_DATA are for ECM mode (config #2). USB_CLASS_VENDOR_SPEC
is for the vendor mode (config #1). However, we are not interesting
in USB_CLASS_CDC_DATA for probe(), so redefine REALTEK_USB_DEVICE
to ignore the USB interface class of USB_CLASS_CDC_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a error for r8152_submit_rx(), add the remaining rx
buffers to the list. Then the remaining rx buffers could be
submitted later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The behavior of handling the returned status from r8152_submit_rx()
is almost same, so let r8152_submit_rx() deal with the error
directly. This could avoid the duplicate code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is unplugged or !netif_running(), the workqueue
doesn't need to wake the device, and could return directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the flag of SCHEDULE_TASKLET in bottom_half() to avoid
re-schedule the tasklet again by workqueue.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_LIST_HEAD(&tp->rx_done) would be done in rtl_start_rx(),
so remove the unnecessary one in alloc_all_mem().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PIDs are only used in the id table, so the definitions are
unnacessary. Remove them wouldn't have confusion.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace using VID/PID with using tp->version to initialize the ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move r8152b_get_version() to the location before rtl_ops_init().
Then, the rtl_ops_init() could use tp->version.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the tasklet only be enabled after open(), and be disabled for
the other situation. The tasklet is only necessary after open() for
tx/rx, so it could be disabled by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set RTL8152_UNPLUG when finding -ENODEV. This could accelerate
unloading the driver when the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.
Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tx_underun with tx_underrun for checkpatch.pl.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove calling cancel_delayed_work_sync() for runtime suspend,
because it would cause dead lock. Instead, return -EBUSY to
avoid the device enters suspending if the net is running and
the delayed work is pending or running. The delayed work would
try to wake up the device later, so the suspending is not
necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the mutex to avoid the settings are interrupted by other ones.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add usb_autopm_xxx for rtl8152_get_settings() ,and remove
usb_autopm_xxx from read_mii_word() and write_mii_word().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restart autonegotiation is necessary after setting EEE.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resume the device before setting the MAC address.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to enable EEE and set EEE advertisement.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the EEE definitions with the ones which is declared
in "mdio.h".
Chage some definitions to make them readable.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off would be called when autoresuming, even though
the cable is plugged. This causes some applications do relative
actions when detecting the carrier off. Keep the status of the
carrier, and let it be modified when the linking change occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw is in ALDPS mode, the hw may have no response for accessing
the most registers. Therefore, the ALDPS should be disabled before
accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
wouldn't enter ALDPS mode when linking on. The hw would enter the
ALDPS mode after several seconds when link down occurs and the ALDPS
is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support hw VLAN for tx and rx. And enable them by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace mdelay with usleep_range to avoid busy loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw doesn't have a valid MAC address, give a random one and
set it to the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exchange the location of rtl8152_set_mac_address() and
set_ethernet_addr(). Then, the set_ethernet_addr() could
set the MAC address by calling rtl8152_set_mac_address()
later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable "rx_buf_sz" is used by both tx and rx buffers. Replace
it with "agg_buf_sz".
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the Tx has the features of stopping queue and aggregation,
We don't need many tx buffers. Change the tx number from 10 to 4
to reduce the usage of the memory. This could save 16K * 6 bytes
memory.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the strncpy with strlcpy, and use sizeof to determine the
length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
626: CHECK: Alignment should match open parenthesis
646: CHECK: Alignment should match open parenthesis
655: CHECK: Alignment should match open parenthesis
695: CHECK: Alignment should match open parenthesis
729: CHECK: Alignment should match open parenthesis
739: CHECK: Alignment should match open parenthesis
976: WARNING: externs should be avoided in .c files
1314: CHECK: Alignment should match open parenthesis
1358: WARNING: networking block comments don't use an empty /* line, use /* Comment...
1402: WARNING: networking block comments don't use an empty /* line, use /* Comment...
1521: CHECK: multiple assignments should be avoided
1775: CHECK: Alignment should match open parenthesis
1838: CHECK: multiple assignments should be avoided
1843: CHECK: multiple assignments should be avoided
1847: CHECK: multiple assignments should be avoided
1850: WARNING: Missing a blank line after declarations
1864: CHECK: Alignment should match open parenthesis
1872: CHECK: braces {} should be used on all arms of this statement
1906: CHECK: usleep_range is preferred over udelay
2865: WARNING: networking block comments don't use an empty /* line, use /* Comment...
3088: CHECK: Alignment should match open parenthesis
total: 0 errors, 5 warnings, 16 checks, 3567 lines checked
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the usb speed of the RTL8152 is not high speed, the USB_DEV_STAT[2:1]
should be equal to [0 1]. That is, the STAT_SPEED_FULL should be equal
to 2.
There is a easy way to check the usb speed by the speed field of the
struct usb_device. Use it to replace the original metheod.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transport offset of the IPv4 packet should be fixed and wouldn't
be out of the hw limitation, so the r8152_csum_workaround() should
be used for IPv6 packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum jumbo frame size for RTL8153 is 9K bytes.
Change the max rx packet size to 9K.
Change the use of the shared fifo from 6K (default) to 12K for tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device should be waked up from runtime suspend before dumping
the hw counter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_cow_head() before editing the tx packet header. The header
would be reallocated if it is shared.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support hw IPv6 checksum for TCP and UDP packets.
Note that the hw has the limitation of the range of the transport
offset. Besides, the TCP Pseudo Header of the IPv6 TSO of the hw
bases on the Microsoft document which excludes the packet length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support scatter gather and TSO.
Adjust the tx checksum function and set the max gso size to fix the
size of the tx aggregation buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue dealing with the remain rx packets, even though the allocation
of the skb fail. This could calculate the correct dropped packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move the tx_bottom() from delayed_work to tasklet. It makes the rx
and tx balanced. If the device is in runtime suspend when getting
the tx packet, wakeup the device before trasmitting.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check tx agg list before spin lock to avoid doing spin lock every
times.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use spin_lock and spin_unlock in interrupt context.
The ndo_start_xmit would not be called in interrupt context, so
replace the relative spin_lock_irqsave and spin_unlock_irqrestore
with spin_lock_bh and spin_unlock_bh.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_get_stats() returns the point address of the struct
net_device_stats. This could be got from struct net_device directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some empty lines. Replace the spaces with the tabs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are known issues for switching the drivers between ECM mode and
vendor mode. The interrup transfer may become abnormal. The hardware
may have the opportunity to die if you change the configuration without
unloading the current driver first, because all the control transfers
of the current driver would fail after the command of switching the
configuration.
Although to use the ecm driver and vendor driver independently is fine,
it may have problems to change the driver from one to the other by
switching the configuration. Additionally, now the vendor mode driver
is more powerful than the ECM driver. Thus, disable the ECM mode driver,
and let r8152 to set the configuration to vendor mode and reset the
device automatically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace netif_rx with netif_receive_skb to avoid disabling irq frequently
for increasing the efficiency.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support runtime suspend for RTL8152 and RTL8153.
Move tx_bottom() from tasklet to delayed_work. That avoids to
transmit tx packets after calling autosuspend.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add up method for rtl_ops and asign relative functions. Move
clear_bp() and hw_phy_cfg() from init method to up method of rtl_ops.
Call rtl_ops.up() for ndo_open() and rtl_ops.down for ndo_stop().
Replace allocating the memory in probe() with in ndo_open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY reset is necessary after some hw settings. However, it would
cause the linking down, and so does the set_speed function. Combine
the PHY reset with set_speed function. That could reduce the frequency
of linking down and accessing the PHY register.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the method of enabling the PHY to clear BMCR_PDOWN only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace getting one item from a list with getting the whole list one time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for RTL_VER_01, replace loading the MAC address from PLA_IDR
with from PLA_BACKUP. The default MAC address may be modified by
the other OS, so the PLA_IDR may be not the default MAC address.
The data in the PLA_BACKUP address of the RTL_VER_01 may be destoryed,
so load MAC address from PLA_IDR for RTL_VER_01.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the following functions.
- r8153_u1u2en
- r8153_u2p3en
- r8153_power_cut_en
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some codes with the following three functions.
- rtl_drop_queued_tx
- rxdy_gated_en
- r8152_power_cut_en
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the following functions which is for the further coding.
- rtl_clear_bp
- r8153_clear_bp
- r8153_teredo_off
- r8152b_disable_aldps
- r8152b_enable_aldps
- r8152b_hw_phy_cfg
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The submission of the interrupt transfer should be done after setting
the bit of WORK_ENABLE, otherwise the callback function would have
the opportunity to be returned directly.
Clear the bit of WORK_ENABLE before killing the interrupt transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that the ecm and r8152 drivers couldn't coexist.
- Remove the devices from the blacklist of relative drivers.
- Remove usb_driver_set_configuration() from r8152 driver.
- Modify the id_table of the r8152 driver for the vendor mode only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings and error:
- WARNING: usb_free_urb(NULL) is safe this check is probably not required
- WARNING: kfree(NULL) is safe this check is probably not required
- ERROR: do not use C99 // comments
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 could support RTL8153. Update the relative descriptor.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Replace pr_warn_ratelimited() with net_ratelimit() and netdev_warn().
- Adjust the algnment of some messages.
- Remove the peroid.
- Fix some messages don't have terminating newline.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the boolean value with the error code for the return value
of the rtl_ops_init().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some information of the device may be used in other functions. Move
the relative code to make sure it would be initialzed correctly
before using it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the tabs of the variables declaration with the spaces.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value should be the boolean value, not the error code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new chip RTL8153 which is the USB 3.0 giga ethernet adapter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the contents of rtl8152_enable() into rtl_set_eee_plus() and
rtl_enable().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different chips may have different settings. This makes it easy
to let different chips have the same flow with differnt settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace RX_BUF_THR with RX_THR_HIGH.
Replace RWSUME_INDICATE with RESUME_INDICATE.
Add CRC_SIZE, TX_ALIGN, and RX_ALIGN.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old method to access PHY is through mdio channel. Replace it
with the OCP channel.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the locations of rtl8152_unload() and ocp_reg_write().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data from the hardware should be little endian. Correct the
declaration.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum packet number which a tx aggregation buffer could contain
is the tx_qlen.
tx_qlen = buffer size / (packet size + descriptor size).
If the tx buffer is empty and the queued packets are more than the
maximum value which is defined above, stop the tx queue. Wake the
tx queue if tx queue is stopped and the queued packets are less than
tx_qlen.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code for sending the packet in the rtl8152_start_xmit().
Let rtl8152_start_xmit() to queue the packet only, and schedule a
tasklet to send the queued packets. This simplify the code and make
sure all the packet would be sent by the original order.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx/rx would access the memory which is out of the desired range.
Modify the method of checking the end of the memory to avoid it.
For r8152_tx_agg_fill(), the variable remain may become negative.
However, the declaration is unsigned, so the while loop wouldn't
break when reaching the end of the desied memory. Although to change
the declaration from unsigned to signed is enough to fix it, I also
modify the checking method for safe. Replace
remain = rx_buf_sz - sizeof(*tx_desc) -
(u32)((void *)tx_data - agg->head);
with
remain = rx_buf_sz - (int)(tx_agg_align(tx_data) - agg->head);
to make sure the variable remain is always positive. Then, the
overflow wouldn't happen.
For rx_bottom(), the rx_desc should not be used to calculate the
packet length before making sure the rx_desc is in the desired range.
Change the checking to two parts. First, check the descriptor is in
the memory. The other, using the descriptor to find out the packet
length and check if the packet is in the memory.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split some parts of code into another function to simplify
tx_bottom(). Use while loop to replace the goto loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some declearation of variables in rx_bottom().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use r8152_get_tx_agg for getting tx agg list
- Replace submit rx with goto submit
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the type of contex of tx_agg and rx_agg from void * to
staruc r8152 *.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the interrupt transfer to replace polling link status.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the tx/rx aggregation which could contain one or more packets
for each bulk in/out. This could reduce the loading of the host
controller by sending less bulk transfer.
The rx packets in the bulk in buffer should be 8-byte aligned, and
the tx packets in the bulk out buffer should be 4-byte aligned.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix the conversion between cpu and __le32
- replace some pla_ocp and usb_ocp functions with generic_ocp function
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
