By dereferencing the MIPI command buffer as a u32* we rely on it being
correctly aligned on ARM, but this may not be the case. Copy it into a
stack variable that will be correctly aligned.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-11-john@metanate.com
Requesting the HS clock from the PHY before we initialize it causes an
invalid signal to be sent out since the input clock is not yet
configured. The PHY databook suggests only asserting this signal when
performing HS transfers, so let's do that.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-10-john@metanate.com
Instead of always sending commands in LP mode, respect the
MIPI_DSI_MSG_USE_LPM flag to decide how to send each message. Also
request acks if MIPI_DSI_MSG_REQ_ACK is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-9-john@metanate.com
We want to check that both the GEN_CMD_EMPTY and GEN_PLD_W_EMPTY bits
are set so we can't just check "val & mask" because that will be true if
either bit is set.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-6-john@metanate.com
In a couple of places here we use "val" for the value that is about to
be written to a register but then reuse the same variable for the value
of a status register before we get around to writing it. Rename the
value to be written to so that we write the value we intend to and not
what we have just read from the status register.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-5-john@metanate.com
This is not needed since we can access the mode via the CRTC from the
enable hook. Also remove the "mode" field that is no longer used.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-4-john@metanate.com
This shows that we only use the mode from the enable function and
prepares us to remove the "mode" field and the mode_set hook in the next
commit.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-3-john@metanate.com
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function, which is the atomic version of "commit" so let's use
the enable hook rather than commit while we're at it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-2-john@metanate.com
If link training at a link rate optimal for a particular
mode fails during modeset's atomic commit phase, then we
let the modeset complete and then retry. We save the link rate
value at which link training failed, update the link status property
to "BAD" and use a lower link rate to prune the modes. It will redo
the modeset on the current mode at lower link rate or if the current
mode gets pruned due to lower link constraints then, it will send a
hotplug uevent for userspace to handle it.
This is also required to pass DP CTS tests 4.3.1.3, 4.3.1.4,
4.3.1.6.
v9:
* Use the trimmed max values of link rate/lane count based on
link train fallback (Daniel Vetter)
v8:
* Set link_status to BAD first and then call mode_valid (Jani Nikula)
v7:
Remove the redundant variable in previous patch itself
v6:
* Obtain link rate index from fallback_link_rate using
the helper intel_dp_link_rate_index (Jani Nikula)
* Include fallback within intel_dp_start_link_train (Jani Nikula)
v5:
* Move set link status to drm core (Daniel Vetter, Jani Nikula)
v4:
* Add fallback support for non DDI platforms too
* Set connector->link status inside set_link_status function
(Jani Nikula)
v3:
* Set link status property to BAd unconditionally (Jani Nikula)
* Dont use two separate variables link_train_failed and link_status
to indicate same thing (Jani Nikula)
v2:
* Squashed a few patches (Jani Nikula)
Acked-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Harry Wentland <Harry.wentland@amd.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/d796cc0c2814d668a47ef43c464f9a4089d46d64.1481883920.git.jani.nikula@intel.com
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so it's not necessary to call
drm_debugfs_remove_files(). Additionally it uses
debugfs_remove_recursive() to clean up the debugfs files, so no need
to do that.
Cc: robdclark@gmail.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-10-noralf@tronnes.org
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so the drm_driver.debugfs_cleanup callback is not
needed. Additionally it uses debugfs_remove_recursive() to clean
up the debugfs files, so no need for adding fake drm_info_node
entries.
Cc: bskeggs@redhat.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-11-noralf@tronnes.org
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so no need to do this explicitly. Additionally it
uses debugfs_remove_recursive() to clean up the debugfs files,
so no need for adding fake drm_info_node entries.
And finally there's no need to clean up on error,
drm_debugfs_cleanup() is called in the error path.
Cc: linux@armlinux.org.uk
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-6-noralf@tronnes.org
Fixed the following style issues
drivers/gpu/vga/vga_switcheroo.c:98: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:99: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:102: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:103: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:129: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:135: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:217: WARNING: line over 80 characters
drivers/gpu/vga/vga_switcheroo.c:218: WARNING: line over 80 characters
drivers/gpu/vga/vga_switcheroo.c:308: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:340: WARNING: line over 80 characters
drivers/gpu/vga/vga_switcheroo.c:1087: WARNING: Block comments use * on subsequent lines
drivers/gpu/vga/vga_switcheroo.c:1087: WARNING: Block comments use a trailing */ on a separate line
Signed-off-by: Joan Jani <igiann@hotmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/HE1PR1001MB1148F38207BC31C860FAF06DC9560@HE1PR1001MB1148.EURPRD10.PROD.OUTLOOK.COM
Use a more common logging style.
Miscellanea:
o Coalesce formats and realign arguments
o Neaten a few macros now using pr_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/76355db47b31668bb64d996865ceee53bd66b11f.1488285953.git.joe@perches.com
It's still just an experiment, but one lesson learned from drm-misc is
that not updating MAINTAINERS just leads to confusion. And this is
easy to revert.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228193657.3559-1-daniel.vetter@ffwll.ch
I had written most of my comments as if I was describing the
individual code files the way I used to for doxygen, while for RST we
want to describe things in a more chapter/section way where there's no
obvious relation to .c files.
Additionally, several of the files had stub descriptions that I've
taken this opportunity to extend.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227201144.10970-4-eric@anholt.net
Commonly used desktop environments such as xfce4 and gnome
on debian sid can flood the graphics drivers with cursor
updates. Because the current implementation is waiting
for a vblank between cursor updates, this will cause the
display to hang for a long time since a typical refresh
rate is only 60Hz.
This is unnecessary and unexpected by user mode software,
so simply swap out the cursor frame buffer without waiting.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224015431.24583-1-mzoran@crowfest.net
In the qxl atomic model, the primary doesn't stay pinned all the time,
instead it is only pinned/unpinned between prepare_fb and cleanup_fb.
So, we no longer need a final unpin of the primary framebuffer when
disabling the crtc.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227204328.18761-9-krisman@collabora.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Every attempt to pin/unpin objects in memory requires
qxl_bo_reserve/unreserve calls around the pinning operation to protect
the object from concurrent access, which causes that call sequence to be
reproduced every place where pinning is needed. In some cases, that
sequence was not executed correctly, resulting in potential unprotected
pinning operations.
This commit encapsulates the reservation inside a new wrapper to make
sure it is always handled properly. In cases where reservation must be
done beforehand, for some reason, one can use the unprotected version
__qxl_bo_pin/unpin.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227204328.18761-3-krisman@collabora.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently the functions that initialize and tear down a connector
iterator use the _get() and _put() suffixes. However, these suffixes
are typically used by reference counting functions.
Make these function names a little more consistent by changing the
suffixes to _begin() and _end(), which is a fairly common pattern in
the rest of the Linux kernel.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228144643.5668-8-thierry.reding@gmail.com
For consistency with other reference counting APIs in the kernel, add
drm_property_blob_get() and drm_property_blob_put() to reference count
DRM blob properties.
Compatibility aliases are added to keep existing code working. To help
speed up the transition, all the instances of the old functions in the
DRM core are already replaced in this commit.
A semantic patch is provided that can be used to convert all drivers to
the new helpers.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228144643.5668-7-thierry.reding@gmail.com
For consistency with other reference counting APIs in the kernel, add
drm_gem_object_get() and drm_gem_object_put(), as well as an unlocked
variant of the latter, to reference count GEM buffer objects.
Compatibility aliases are added to keep existing code working. To help
speed up the transition, all the instances of the old functions in the
DRM core are already replaced in this commit.
The existing semantic patch for the DRM subsystem-wide conversion is
extended to account for these new helpers.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228144643.5668-6-thierry.reding@gmail.com
For consistency with other reference counting APIs in the kernel, add
drm_framebuffer_get() and drm_framebuffer_put() to reference count DRM
framebuffers.
Compatibility aliases are added to keep existing code working. To help
speed up the transition, all the instances of the old functions in the
DRM core are already replaced in this commit.
The existing semantic patch for the DRM subsystem-wide conversion is
extended to account for these new helpers.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228144643.5668-5-thierry.reding@gmail.com
For consistency with other reference counting APIs in the kernel, add
drm_connector_get() and drm_connector_put() functions to reference count
connectors.
Compatibility aliases are added to keep existing code working. To help
speed up the transition, all the instances of the old functions in the
DRM core are already replaced in this commit.
The existing semantic patch for mode object reference count conversion
is extended for these new helpers.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228144643.5668-4-thierry.reding@gmail.com
For consistency with other reference counting APIs in the kernel, add
drm_mode_object_get() and drm_mode_object_put() to reference count DRM
mode objects.
Compatibility aliases are added to keep existing code working. To help
speed up the transition, all the instances of the old functions in the
DRM core are already replaced in this commit.
A semantic patch is provided that can be used to convert all drivers to
the new helpers.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228144643.5668-3-thierry.reding@gmail.com
Subsequent patches will introduce reference counting APIs that are more
consistent with similar APIs throughout the Linux kernel. These APIs use
the _get() and _put() suffixes and will collide with this existing
function.
Rename the function to drm_mode_object_add() which is a slightly more
accurate description of what it does. Also the kerneldoc for this
function gives an indication that it's badly named because it doesn't
actually acquire a reference to anything.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228144643.5668-2-thierry.reding@gmail.com
Use a more common logging style.
Miscellanea:
o Coalesce formats and realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
[danvet: Resolve minor conflict in drm_edid.c]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
