If there are pending page flips when the fd gets closed those page
flips may have events associated to them. When the page flip eventually
completes it will queue the event to file_priv->event_list, but that
may be too late and file_priv->event_list has already been cleaned up.
Thus we leak a bit of kernel memory in the form of the event structure.
To avoid such problems clear out such pending events from
intel_crtc->unpin_work at ->preclose(). Any event that already made it
to file_priv->event_list will get cleaned up by the drm_release_events()
a bit later.
We can ignore the file_priv->event_space accounting since file_priv is
going away. This is already how drm core deals with pending vblank
events, which are maintained by the drm core.
What saves us from a total disaster (ie. dereferencing and alrady
freed file_priv) is the fact that the fb descruction triggers a modeset
and there we wait for pending flips.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Propagate the error from intel_update_plane() up through
intel_plane_restore() to the caller. This will be used for
rollback purposes when setting properties fails.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sprite planes (in fact all display planes starting from gen4)
support 180 degree rotation. Add the relevant low level bits to the
sprite code to make use of that feature.
The upper layers are not yet plugged in.
v2: HSW handles the rotated buffer offset automagically
v3: BDW also handles the rotated buffer offset automagically
Testcase: igt/kms_rotation_crc
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Share the waitqueue that drm_irq uses when performing the vblank evade
trick for atomic pipe updates.
v2: Keep intel_pipe_handle_vblank() (Chris)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Gen < 8, set M2_N2 registers on every mode set. This is required to make
sure M2_N2 registers are set during boot, resume from sleep for cross-
checking the state. The register is set only if DRRS is supported.
v2: Patch rebased
v3: Daniel's review comments
- Removed HAS_DRRS(dev) and added bool has_drrs to pipe_config to
track drrs support
v4: Jesse's review comments
- Made changes to set m2_n2 in intel_dp_set_m_n()
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.
v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Historically we've exposed the full backlight PWM duty cycle range to
the userspace, in the name of "mechanism, not policy". However, it turns
out there are both panels and board designs where there is a minimum
duty cycle that is required for proper operation. The minimum duty cycle
is available in the VBT.
The backlight class sysfs interface does not make any promises to the
userspace about the physical meaning of the range
0..max_brightness. Specifically there is no guarantee that 0 means off;
indeed for acpi_backlight 0 usually is not off, but the minimum
acceptable value.
Respect the minimum backlight, and expose the range acceptable to the
hardware as 0..max_brightness to the userspace via the backlight class
device; 0 means the minimum acceptable enabled value. To switch off the
backlight, the user must disable the encoder.
As a side effect, make the backlight class device max brightness and
physical PWM modulation frequency (i.e. max duty cycle)
independent. This allows a follow-up patch to virtualize the max value
exposed to the userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we use the runtime IRQ enable/disable functions in our suspend
path, we can simply check the pm._irqs_disabled flag everywhere. So
rename it to catch the users, and add an inline for it to make the
checks clear everywhere.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move it from hsw_power_well_post_enable() (intel_pm.c) to i915_irq.c
so we can reuse the nice IRQ macros we have there. The main difference
is that now we're going to check if the IIR register is non-zero when
we try to re-enable the interrupts.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Traditionally we use genX_ for GT/render stuff and the codenames for
display stuff. But the gt and pm interrupt handling functions on
gen5/6+ stuck out as exceptions, so convert them.
Looking at the diff this nicely realigns our ducks since almost all
the callers are already platform-specific functions following the
genX_ pattern.
Spotted while reviewing some internal rps patches.
No function change in this patch.
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the future, we'll need the height of the fb to fetch from memory for
WM computation.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create and attach the drm property to set aspect ratio. If there is no user
specified value, then PAR_NONE/Automatic option is set by default. User can
select aspect ratio 4:3 or 16:9. The aspect ratio selected by user would
come into effect with a mode set.
v2: Modified switch case to include aspect ratio enum changes
v3: Modified the patch according the change in the earlier patch to return
errno in case property creation fails. With this change, property will be
attached only if creation is successful
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.
- Use frontbuffer tracking bits stuff to separate disable and
re-enable.
- Don't re-check everything in the psr work. We have now accurate
tracking for everything, so no need to check for sprites or tiling
really. Allows us to ditch tons of locks.
- That in turn allows us to properly cancel the work in the disable
function - no more deadlocks.
- Add a check for HSW sprites and force a flush. Apparently the
hardware doesn't forward the flushing when updating the sprite base
address. We can do the same trick everywhere else we have such
issues, e.g. on baytrail with ... everything.
- Don't re-enable psr with a delay in psr_exit. It really must be
turned off forever if we detect a gtt write. At least with the
current frontbuffer render tracking. Userspace can do a busy ioctl
call or no-op pageflip to re-enable psr.
- Drop redundant checks for crtc and crtc->active - now that they're
only called from enable this is guaranteed.
- Fix up the hsw port check. eDP can also happen on port D, but the
issue is exactly that it doesn't work there. So an || check is
wrong.
- We still schedule the psr work with a delay. The frontbuffer
flushing interface mandates that we upload the next full frame, so
need to wait a bit. Once we have single-shot frame uploads we can do
better here.
v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.
v3: s/psr_exit/psr_invalidate/ for consistency
v4: Fixup whitespace.
v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.
v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
by Rodrigo.
- Comments Chris requested to clarify the code.
v7: Fix conflict on rebase (Rodrigo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, after i915_pm_suspend display power wells are staying
power ungated. So, after initiating mem sleep "echo mem > /sys/power/state"
Display is staing D0 State. There might be better way/place to power gate
these wells. Also, we need to make sure that if wells are power gated due to
DPMS OFF sequence, they need not be turned off by i915_pm_suspend again.
v2: Extracted helper for intel_crtc_disable and power gating CRTC power wells.
[Daniel]
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Change-Id: I34c80da66aa24c423a5576c68aa1f3a8d0f43848
Signed-off-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To be able to do this we need to separately keep track of how many
crtcs need a given WRPLL and how many actually actively use it. The
common shared dpll framework already has all this, including massive
state readout and cross checking. Which allows us to do this switch in
a fairly small patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly this patch is one big excersize in deleting code and asserts
which are no longer needed. Note that we still abuse the shared dpll
framework a bit since we call the enable/disable functions from the
crtc mode_set and off hooks. But changing the actual hardware sequence
will be done in the next step.
Note that besides the massive amount of changes in this patch the
places and order in which the low-level WRPLL code is called is
absolutely unchanged.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just boring sed job for preparation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an intel_fb_obj() macro that returns the GEM object associated with
a DRM framebuffer. This macro is safe to call on NULL framebuffers (a
NULL object pointer will be returned in this case).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.
Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg
Ver3: moved SYS_RESTART check earlier, new name for pp_div.
Ver4: Minor issue changes
Ver5: Move registration of reboot notifier to edp_connector_init,
Added warning comment to handler about lack of PM notification.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The always-on power well pixel path on haswell is routed such that it
bypasses the panel fitter when we use is. Which means the pfit CRC
source won't work in that configuration.
Add a new disallow-bypass flags to the pfit pipe config state and set
it when we want to use the pf CRC. Results in a bit of flicker, but
should get the job done. We'll also undo do it afterwards to make sure
other tests arent' negatively affected.
Totally untested due to lack of hsw laptops around here.
v2: s/disallow_bypass/force_power_well_on/ to avoid a double negative
(Damien).
v3: force_thru because roadsigns.
v4: Don't forget the power wells! Also note that until the runtime pm
for DPMS series is fully merged the simple disable/enable trick won't
work since the ->crtc_mode_set callback is still required to do nasty
things. This stuff is tricky, but I think by both fixing up
get_crtc_power_domains and the debugfs wa code we should always
grab/drop the additional power well correctly.
v5: Wrap in () as suggested by Damien to avoid setting reserved values
for the edp transcoder path on bdw+
References: https://bugs.freedesktop.org/show_bug.cgi?id=72864
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The digital ports from Ironlake and up have the ability to distinguish
between long and short HPD pulses. Displayport 1.1 only uses the short
form to request link retraining usually, so we haven't really needed
support for it until now.
However with DP 1.2 MST we need to handle the short irqs on their
own outside the modesetting locking the long hpd's involve. This
patch adds the framework to distinguish between short/long to the
current code base, to lay the basis for future DP 1.2 MST work.
This should mean we get better bisectability in case of regression
due to the new irq handling.
v2: add GM45 support (untested, due to lack of hw)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
[danvet: Fix conflicts in i915_irq.c with Oscar Mateo's irq handling
race fixes and a trivial one in intel_drv.h with the psr code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the CMNRESET deassert is part of the cmnlane power well,
intel_reset_dpio() is called too late to make any difference. We've
deasserted CMNRESET by that time, and so the off+on toggle w/a will
never kick in.
Move the workaround to intel_power_domains_init_hw() where it gets
called before we enable the init power domain.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a slightly different way of readoing out the cdclk in
gmbus_set_freq(). Kill that and just call .get_display_clock_speed().
Also need to remove the GMBUSFREQ update from intel_i2c_reset() since
that gets called way too early. Let's do it in intel_modeset_init_hw()
instead, and also pull the initial vlv_cdclk_freq update there from
init_clock gating.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a standard hook for reading out the current cdclk. Move the VLV
code from valleyview_cur_cdclk() to .get_display_clock_speed().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTuaWZAAoJEHm+PkMAQRiGfkIH/2Hhwrg51GWazUYIXVxz5zLU
kPMlaws3vankbhka9HCg02eS3tkzr6shO3F/qlBba+5GUkUDKCcCisIsvk4hgZZg
7YqepTvcaupNxIp4TmTGm1FYVK1GpaWFdJVgg2PDdGFahw3HSlfZoTkBzirNCwga
p/jfeRzathbUixpz9OAC1AEn2gP1AxNRpSt1wShL5rexBb1YRXCPuCEt9B0UsVoR
mzKf5xEsuaZnpCuvWK4S60fjfVhTe8UJ/xGPPfdLyIXU0rvhaKzfeVQO6F5nIQBy
Xvrar1f7oOPZaJRdlmPvAimS7iS8lq/YctuHu7ia1NdJSihtA5sRPf7cWAw2d7s=
=4PrL
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc4' into drm-intel-next-queued
Due to Dave's vacation drm-next hasn't opened yet for 3.17 so I
couldn't move my drm-intel-next queue forward yet like I usually do.
Just pull in the latest upstream -rc to unblock patch merging - I
don't want to needlessly rebase my current patch pile really and void
all the testing we've done already.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse noticed that the punit communication needed to query the VLV power
well status can cause substantial delays. Since we can query the state
frequently, for example during I2C transfers, maintain a cached version
of the HW state to get rid of this delay.
This fixes at least one reported regression where boot time increased by
~4 seconds due to frequent power well state queries on VLV during eDP
EDID read.
This regression has been introduced in
commit bb4932c4f1
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Apr 14 20:24:33 2014 +0300
drm/i915: vlv: check port power domain instead of only D0 for eDP VDD on
Reported-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So these are the guts of the new beast. This tracks when a frontbuffer
gets invalidated (due to frontbuffer rendering) and hence should be
constantly scaned out, and when it's flushed again and can be
compressed/one-shot-upload.
Rules for flushing are simple: The frontbuffer needs one more full
upload starting from the next vblank. Which means that the flushing
can _only_ be called once the frontbuffer update has been latched.
But this poses a problem for pageflips: We can't just delay the
flushing until the pageflip is latched, since that would pose the risk
that we override frontbuffer rendering that has been scheduled
in-between the pageflip ioctl and the actual latching.
To handle this track asynchronous invalidations (and also pageflip)
state per-ring and delay any in-between flushing until the rendering
has completed. And also cancel any delayed flushing if we get a new
invalidation request (whether delayed or not).
Also call intel_mark_fb_busy in both cases in all cases to make sure
that we keep the screen at the highest refresh rate both on flips,
synchronous plane updates and for frontbuffer rendering.
v2: Lots of improvements
Suggestions from Chris:
- Move invalidate/flush in flush_*_domain and set_to_*_domain.
- Drop the flush in busy_ioctl since it's redundant. Was a leftover
from an earlier concept to track flips/delayed flushes.
- Don't forget about the initial modeset enable/final disable.
Suggested by Chris.
Track flips accurately, too. Since flips complete independently of
rendering we need to track pending flips in a separate mask. Again if
an invalidate happens we need to cancel the evenutal flush to avoid
races.
v3:
Provide correct header declarations for flip functions. Currently not
needed outside of intel_display.c, but part of the proper interface.
v4: Add proper domain management to fbcon so that the fbcon buffer is
also tracked correctly.
v5: Fixup locking around the fbcon set_to_gtt_domain call.
v6: More comments from Chris:
- Split out fbcon changes.
- Drop superflous checks for potential scanout before calling intel_fb
functions - we can micro-optimize this later.
- s/intel_fb_/intel_fb_obj_/ to make it clear that this deals in gem
object. We already have precedence for fb_obj in the pin_and_fence
functions.
v7: Clarify the semantics of the flip flush handling by renaming
things a bit:
- Don't go through a gem object but take the relevant frontbuffer bits
directly. These functions center on the plane, the actual object is
irrelevant - even a flip to the same object as already active should
cause a flush.
- Add a new intel_frontbuffer_flip for synchronous plane updates. It
currently just calls intel_frontbuffer_flush since the implemenation
differs.
This way we achieve a clear split between one-shot update events on
one side and frontbuffer rendering with potentially a very long delay
between the invalidate and flush.
Chris and I also had some discussions about mark_busy and whether it
is appropriate to call from flush. But mark busy is a state which
should be derived from the 3 events (invalidate, flush, flip) we now
have by the users, like psr does by tracking relevant information in
psr.busy_frontbuffer_bits. DRRS (the only real use of mark_busy for
frontbuffer) needs to have similar logic. With that the overall
mark_busy in the core could be removed.
v8: Only when retiring gpu buffers only flush frontbuffer bits we
actually invalidated in a batch. Just for safety since before any
additional usage/invalidate we should always retire current rendering.
Suggested by Chris Wilson.
v9: Actually use intel_frontbuffer_flip in all appropriate places.
Spotted by Chris.
v10: Address more comments from Chris:
- Don't call _flip in set_base when the crtc is inactive, avoids redunancy
in the modeset case with the initial enabling of all planes.
- Add comments explaining that the initial/final plane enable/disable
still has work left to do before it's fully generic.
v11: Only invalidate for gtt/cpu access when writing. Spotted by Chris.
v12: s/_flush/_flip/ in intel_overlay.c per Chris' comment.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.
The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.
Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.
v2: Improve the commit message a bit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.
The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.
If this breaks anything then we need to augment the enable/disable
functions accordingly.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse's SOix work required some patches from acpi-next, so pull it in
through a topic barnch.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables the framework for using MMIO based flip calls,
in contrast with the CS based flip calls which are being used currently.
MMIO based flip calls can be enabled on architectures where
Render and Blitter engines reside in different power wells. The
decision to use MMIO flips can be made based on workloads to give
100% residency for Media power well.
v2: The MMIO flips now use the interrupt driven mechanism for issuing the
flips when target seqno is reached. (Incorporating Ville's idea)
v3: Rebasing on latest code. Code restructuring after incorporating
Damien's comments
v4: Addressing Ville's review comments
-general cleanup
-updating only base addr instead of calling update_primary_plane
-extending patch for gen5+ platforms
v5: Addressed Ville's review comments
-Making mmio flip vs cs flip selection based on module parameter
-Adding check for DRIVER_MODESET feature in notify_ring before calling
notify mmio flip.
-Other changes mostly in function arguments
v6: -Having a seperate function to check condition for using mmio flips (Ville)
-propogating error code from i915_gem_check_olr (Ville)
v7: -Adding __must_check with i915_gem_check_olr (Chris)
-Renaming mmio_flip_data to mmio_flip (Chris)
-Rebasing on latest nightly
v8: -Rebasing on latest code
-squash 3rd patch in series(mmio setbase vs page flip race) with this patch
-Added new tiling mode update in intel_do_mmio_flip (Chris)
v9: -check for obj->last_write_seqno being 0 instead of obj->ring being NULL in
intel_postpone_flip, as this is a more restrictive condition (Chris)
v10: -Applied Chris's suggestions for squashing patches 2,3 into this patch.
These patches make the selection of CS vs MMIO flip at the page flip time, and
make the module parameter for using mmio flips as tristate, the states being
'force CS flips', 'force mmio flips', 'driver discretion'.
Changed the logic for driver discretion (Chris)
v11: Minor code cleanup(better readability, fixing whitespace errors, using
lockdep to check mutex locked status in postpone_flip, removal of __must_check
in function definition) (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # snb, ivb
[danvet: Fix up parameter alignement checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The perfect solution for psr_exit is the hardware tracking the changes and
doing the psr exit by itself. This scenario works for HSW and BDW with some
environments like Gnome and Wayland.
However there are many other scenarios that this isn't true. Mainly one right
now is KDE users on HSW and BDW with PSR on. User would miss many screen
updates. For instances any key typed could be seen only when mouse cursor is
moved. So this patch introduces the ability of trigger PSR exit on kernel side
on some common cases that.
Most of the cases are coverred by psr_exit at set_domain. The remaining cases
are coverred by triggering it at set_domain, busy_ioctl, sw_finish and
mark_busy.
The downside here might be reducing the residency time on the cases this
already work very wall like Gnome environment. But so far let's get focused
on fixinge issues sio PSR couild be used for everybody and we could even
get it enabled by default. Later we can add some alternatives to choose the
level of PSR efficiency over boot flag of even over crtc property.
v2: remove exit from connector_dpms. Daniel pointed this is the wrong way and
also this isn't needed for BDW and HSW anyway.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DRM core will translate calls to legacy cursor ioctls into universal
cursor calls automatically, so there's no need to maintain the legacy
cursor support. This greatly simplifies the transition since we don't
have to handle reference counting differently depending on which cursor
interface was called.
The aim here is to transition to the universal plane interface with
minimal code change. There's a lot of cleanup that can be done (e.g.,
using state stored in crtc->cursor->fb rather than intel_crtc) that is
left to future patches.
v4:
- Drop drm_gem_object_unreference() that is no longer needed now that
we receive the GEM obj directly rather than looking up the ID.
v3:
- Pass cursor obj to intel_crtc_cursor_set_obj() if cursor fb changes,
even if 'visible' is false. intel_crtc_cursor_set_obj() will notice
that the cursor isn't visible and disable it properly, but we still
need to get intel_crtc->cursor_addr set properly so that we behave
properly if the cursor becomes visible again in the future without
changing the cursor buffer (noted by Chris Wilson and verified
via i-g-t kms_cursor_crc).
- s/drm_plane_init/drm_universal_plane_init/. Due to type
compatibility between enum and bool, everything actually works
correctly with the wrong init call, except for the type of plane that
gets exposed to userspace (it shows up as type 'primary' rather than
type 'cursor').
v2:
- Remove duplicate dimension checks on cursor
- Drop explicit cursor disable from crtc destroy (fb & plane
destruction will take care of that now)
- Use DRM plane helper to check update parameters
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Pallavi G<pallavi.g@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the system to enter the lowest power mode during system freeze.
v2: delete force wake timer at suspend (Imre)
v3: add GT work suspend function (Imre)
v4: use uncore forcewake reset (Daniel)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those LUT where defined in the original sprite patch introducing intel_plane,
but were never used.
commit b840d907fc
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Dec 13 13:19:38 2011 -0800
drm/i915: add SNB and IVB video sprite support v6
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Pimp commit message as suggested by Damien]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Functions that can't fail are such a bliss to work with, it'd be shame
to miss the occasion. The "failure" mode is the DSI connector not being
created, the rest of the initialization can carry on happily.
We weren't even checking that value anyway.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Also convert the missed return statement due to other patches
merged meanwhile.]
[danvet2: Squash in fixup from Damien to remove empty return; at the
end of intel_dsi_init.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"Because our driver assumes only one panel is PSR capable, and we
already have other PSR information on dev_priv instead of intel_dp. If
we ever support multiple PSR panels, we'll have to move struct
i915_psr to intel_dp anyway." (by Paulo)
v2: Avoid more than one setup. Removing initialization
and trusting allocation. (By Paulo Zanoni).
v3: rebase.
v4: Adding comment.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible for userspace to create a big object large enough for a
256x256, and then switch over to using it as a 64x64 cursor. This
requires the cursor update routines to check for a change in width on
every update, rather than just when the cursor is originally enabled.
This also fixes an issue with 845g/865g which cannot change the base
address of the cursor whilst it is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[Antti:rebased, adjusted macro names and moved some lines, no functional
changes]
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Tested-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Cc: stable@vger.kernel.org
Testcase: igt/kms_cursor_crc/cursor-size-change
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a bit like the CMN reset de-assert we do in DPIO_CTL, except
that it resets the whole common lane section of the PHY. This is
required on machines where the BIOS doesn't do this for us on boot or
resume to properly re-calibrate and get the PHY ready to transmit data.
Without this patch, such machines won't resume correctly much of the time,
with the symptom being a 'port ready' timeout and/or a link training
failure.
Note that simply asserting reset at suspend and de-asserting at resume
is not sufficient, nor is simply de-asserting at boot. Both of these
cases have been tested and have still been found to have failures on
some configurations.
v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.
On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.
As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.
v2: Clarify HSW+ situation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write to the primary plane base address registrer when we
enable/disable the primary plane in response to sprite coverage. Those
writes will cause the flip counter to increment which could interfere
with the detection of CS flip completion. We could end up completing
CS flips before the CS has even executed the commands from the ring.
To avoid such issues, wait for CS flips to finish before we toggle the
primary plane on/off.
v2: Rebased due to atomic sprite update changes
Testcase: igt/kms_mmio_vs_cs_flip/setplane_vs_cs_flip
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.
As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in the drm vblank rework from Ville and me. drm core parts acked
by Dave Airlie
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Just a bit of fun around the placement of drm_vblank_on. This merge
resolution has been tested in drm-intel-nightly for a while already.
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have hardware based disable bits on gmch platforms, so need
to block spurious underrun reports in software. Which means that we
_must_ start out with fifo underrun reporting disabled everywhere.
This is in big contrast to ilk/hsw/cpt where there's only _one_
disable bit for all platforms and hence we must allow underrun
reporting on disabled pipes. Otherwise nothing really works,
especially the CRC support since that's key'ed off the same irq
disable bit.
This allows us to ditch the fifo underrun reporting hack from the vlv
runtime pm code and unexport the internal function from i915_irq.c
again. Yay!
v2: Keep the display irq disabling, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
