The e1000 driver has a workaround for 82544 on PCI-X where if the
terminating byte of a buffer is at addresses 0-3 mod 8, then 4 bytes
are shaved off it and defered to a new segment. This is due to an
erratum that could otherwise cause TX hangs.
Unfortunately this breaks TSO because it may cause the TCP header to
be split over two segments which itself causes TX hangs. The solution
is to pull 4 bytes of data up from the next segment rather than pushing
4 bytes off. This ensures the TCP header remains in one piece and
works around the PCI-X hang.
This patch is based on one from Jesse Brandeburg.
This bug has been trigered by both CONFIG_DEBUG_SLAB as well as Xen.
Note that the only reason we don't see this normally is because the
TCP stack starts writing from the end, i.e., it writes the TCP header
first then slaps on the IP header, etc. So the end of the TCP header
(skb->tail - 1 here) is always aligned correctly.
Had we made the start of the IP header (e.g., IPv6) 8-byte aligned
instead, this would happen for normal TCP traffic as well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
--
Visit Openswan at http://www.openswan.org/
Email: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently after an interface up, the link state is detected 2 seconds later
when the first watchdog timer runs. This patch changes that by triggering
the hardware to generate a link-change interrupt from the up() function
instead. This has the result that the link state gets detected immediately
and without races. This has the potential to speed up booting since a normal
distribution boot process waits for a link before DHCP is attempted.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 3 extra packet redirect counters for tracking purposes to make sure
we can test that all packets arrive properly.
Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>,
rewritten to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the user to vary the size that copybreak works. Currently cb is enabled
for packets < 256 bytes, but various tests indicate that this should be
configurable for specific use cases. In addition, this parameter allows us
to force never/always during testing to get full and predictable coverage of
both code paths.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Assign the PBA to be large enough to contain at least 2 jumbo frames on
all adapters. This dramatically increases performance on several adapters
and fixes TX performance degradation issues where the PBA was misallocated
in the old algorithm.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
the driver has (ancient) code for messing with TIPG from the 82542 days.
Unfortunately this code was running on our current adapters and setting
TIPG for fiber to be +1 over the copper value. This caused 1.45Mpps
to be sent instead of 1.487Mpps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For older adapters we know that they are of the PCI bus type, so we can
just set this.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This bugfix makes sure that the driver data reflects the full new situation
before the adapter is reinitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In rare occasions, ESB2 systems would end up started without the RX
unit being turned on. Add a check that runs post-init to work around
this issue.
Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>,
rewritten to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CONFIG_DEBUG_SLAB changes alignments of the data structures the slab
allocators return. These break certain workarounds for TSO on the 82544.
Since DEBUG_SLAB is relatively rare and not used for performance sensitive
cases, the simplest fix is to disable TSO in this special situation.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the user has forced gigabit speed, phy power management must be disabled;
otherwise the NIC would try to negotiate to a linkspeed of 10/100 mbit on
shutdown, which would lead to a total loss of link. This loss of link breaks
Wake-on-Lan and IPMI.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several bugs existed in how we handle manageability issues all
over the driver. This patch consolidates all the managability
release and init code in two single functions and call them from
appropriate locations. This fixes several BMC packet redirect issues
and powerup/down hiccups.
Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>, rewritten
to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 82543 chip does not count tx_carrier_errors properly in FD mode;
report zeros instead of garbage.
Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>, rewritten
to use feature flags by me.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The dynamic interrupt rate control patches omitted proper counting
for jumbo's and TSO resulting in suboptimal interrupt mitigation strategies.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The lower 2 bits of a user-supplied itr setting (via ethtool) need to be
masked off: These lower two bits are used as control bits.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
... into anonymous union of __wsum and __u32 (csum and csum_offset resp.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ia64:
drivers/built-in.o(.text+0xd9a72): In function `e1000_xmit_frame':
: undefined reference to `csum_ipv6_magic'
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a new dynamic itr algorithm, with 2 modes, and make it the default
operation mode. This greatly reduces latency and increases small packet
performance, at the "cost" of some CPU utilization. Bulk traffic
throughput is unaffected.
The driver can limit the amount of interrupts per second that the
adapter will generate for incoming packets. It does this by writing a
value to the adapter that is based on the maximum amount of interrupts
that the adapter will generate per second.
Setting InterruptThrottleRate to a value greater or equal to 100 will
program the adapter to send out a maximum of that many interrupts per
second, even if more packets have come in. This reduces interrupt
load on the system and can lower CPU utilization under heavy load,
but will increase latency as packets are not processed as quickly.
The default behaviour of the driver previously assumed a static
InterruptThrottleRate value of 8000, providing a good fallback value
for all traffic types,but lacking in small packet performance and
latency. The hardware can handle many more small packets per second
however, and for this reason an adaptive interrupt moderation algorithm
was implemented.
Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in
which it dynamically adjusts the InterruptThrottleRate value based on
the traffic that it receives. After determining the type of incoming
traffic in the last timeframe, it will adjust the InterruptThrottleRate
to an appropriate value for that traffic.
The algorithm classifies the incoming traffic every interval into
classes. Once the class is determined, the InterruptThrottleRate
value is adjusted to suit that traffic type the best. There are
three classes defined: "Bulk traffic", for large amounts of packets
of normal size; "Low latency", for small amounts of traffic and/or
a significant percentage of small packets; and "Lowest latency",
for almost completely small packets or minimal traffic.
In dynamic conservative mode, the InterruptThrottleRate value is
set to 4000 for traffic that falls in class "Bulk traffic". If
traffic falls in the "Low latency" or "Lowest latency" class, the
InterruptThrottleRate is increased stepwise to 20000. This default
mode is suitable for most applications.
For situations where low latency is vital such as cluster or
grid computing, the algorithm can reduce latency even more when
InterruptThrottleRate is set to mode 1. In this mode, which operates
the same as mode 3, the InterruptThrottleRate will be increased
stepwise to 70000 for traffic in class "Lowest latency".
Setting InterruptThrottleRate to 0 turns off any interrupt moderation
and may improve small packet latency, but is generally not suitable
for bulk throughput traffic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add a generic MSI interrupt routine that is IO read-free, speeding up
MSI interrupt handling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This file needs some cleanups and reordering - logically order it
so that relevant defines and code are together with properly quoted
defaults.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Spec fix: don't set IDE unless we are actually setting the tx
int delay time.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
ICH8 will soon be followed by newer chipsets bearing the same acronym,
thus we remove the '8' and make it independent of the version number in
the platform name.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add a netif_wake/start_queue counter to the ethtool statistics to indicated
to the user that their transmit ring could be too small for their workload.
Signed-off-by: Jesse brandeburg <jesse.brandeburg@intel.com>
Cc: Jamal Hadi <hadi@cyberus.ca>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add support for a Low Profile quad-port PCI-E adapter and 2 variants
of the ICH8 systems' onboard NIC's.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This memsetting was added in a paranoid rage debugging TX hangs, but
are no longer of importance. We can beef up the performance quite a
bit removing them. Make sure to fill in next_to_watch to allow this.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Order pci-e capability struct according to bus/pci bus width ordering
preserving the hard pci spec numbers.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On ich systems during PHY power down to D3, the voltage regulators
were left on.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IA64 SMP systems were seeing TX issues with multiple cpu's attempting
to write tail registers unordered. This mmiowb() fixes the issue.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Enable early receives on 82573 for jumbo frame performance. Jumbo's
are only supported on 82573L with ASPM disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Enable TSO for IPV6. All e1000 hardware supports it. This reduces CPU
utilizations by 50% when transmitting IPv6 frames.
Fix symbol naming enabling ipv6 TSO. Turn off TSO6 for 10/100.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove debugging code disabling MULR (multiple reads). It's not usable
for a wide audience and there are no known problems with MULR right
now.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
e1000: Fix suspend/resume powerup and irq allocation
From: Auke Kok <auke-jan.h.kok@intel.com>
After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.
Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the length (rx_bytes counter) adjustment of 4 bytes down to after the
TBI_ACCEPT workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
82571 and newer chispets don't need to limit desc. length to 4kb and can
handle 8kb sizes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allocations using alloc_page are taking too long for normal MTU, so
use LPE only for jumbo frames.
Signed-off-bu: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Threshold bitmasks for prefetch, host and writeback were clearing
bits that they were not supposed to. The leftmost 2 bits in the byte
for each threshold are reserved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The MANC register should not be read for PCI-E adapters at all, as well as
82543 and older where 82543 would master abort when this register was
accessed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
During the handling of the PCI error recovery sequence, the current e1000
driver erroneously blocks a device reset for any but the first PCI
function. It shouldn't -- this is a cut-n-paste error from a different
driver (which tolerated only one hardware reset per hardware card).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Memory allocated for new tx_ring and rx_ring leaks if
e1000_setup_XX_resources() fails.c Also this patch reduces stack usage
(removed tx_new and rx_new) and uses kzalloc instead kmalloc+memset(0)
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several minor issues exist in the low-level device handling code of
e1000. The NVM and EEPROM writing/reading code was updated which fixes
unneeded delays, adds proper eeprom aqcuiring steps and handle shadow
ram and flash access. Minor cosmetic adjustments to the polarity code
adding symbols. PHY reset code mistakenly distinguished between MAC
types instead of PHY types, and was fixes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We were plagued by our interrupt handler posting a watchdog event which
could occur when our adapter was going down in case a late packet arrived
just before e1000_down() finished. This caused the watchdog timer to start
after the NIC was down and keep rescheduling it every N seconds. Once
the driver unloaded it would panic.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Manageability is using one more RAR entry than we anticipated earlier
for ICH8.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add code to display the detected PCI-E bus width.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
When powering down the PHY (if WoL is disabled) we should only check
copper PHY's and handle PCI-E adapters differently.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several hardware bits were set all over the driver and have been
consolidated into a single function.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Disable jumbo frames for 82573L alltogether and when ASPM is enabled
since the hardware has problems with it. For the NICs that do support
this in the 82573 series we set ERT_2048 to attempt to receive as much
traffic as early as we can.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several manageability capability detection parts hinted towards
our code being incomplete for PCI-E. According to spec, we do not
want to poke any MANC bits at all.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
With a patch, ethtool can now signify the driver to advertise more
than just a single speed/duplex setting. This allows you to tell the
card to advertise in 10/100 in any speed if you don't have a gigabit
switch for instance.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add 4 multicast and broadcast hardware counters (rx/tx), and eliminate
as many non-hardware counters as possible.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We keep getting requests from people that think that this might be
an exploitable hole where we would overwrite 4 bytes in the netdev
struct if the pci name would exceed 15 characters. In reality this
will never happen but we fix it anyway.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This update to the copyright header adds the mailinglist, and aligns it
with the kernel licensing as well as remove the offending 'all rights
reserved'.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Replace CHECKSUM_HW by CHECKSUM_PARTIAL (for outgoing packets, whose
checksum still needs to be completed) and CHECKSUM_COMPLETE (for
incoming packets, device supplied full checksum).
Patch originally from Herbert Xu, updated by myself for 2.6.18-rc3.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch in -mm3 titled
"gregkh-pci-pci-don-t-enable-device-if-already-enabled.patch" causes
pci_enable_device() to be a no-op if the kernel thinks that the device is
already enabled. This change breaks the PCI error recovery mechanism in
the e1000 device driver, since, after PCI slot reset, the card is no longer
enabled. This is a trivial fix for this problem. Tested.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The commit 'e1000: Remove 0x1000 as supported device' (Jeff Kirsher,
673a052fde) Removes PIC device ID 8086:1000
from the list of supported devices. A fix was submitted for the original
issue (commit 6a9516989f).
This commit reverts commit 673a052fde and
re-enables 82542rev3 chips completely.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 581d708eb4 (oct. 5 2005) introduced
partial Multiqueue support for e1000 which broke macro smartness in setting
up head/tail registers for 82542 rev3 chipsets, making these adapters
completely non-working since 2.6.15.
This commit sets the proper head and tail registers for read and write
descriptor rings. Ths fix was tested on an 82542 rev3 NIC and newer NICs.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the needlessly global e1000_phy_igp_get_info() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Device 0x10a4 is a double 82571 on a single PCI-Express card and
has 4 gigabit capable ports.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
WoL is constantly giving problems and needed a rewrite. Consolidates
all WoL capabilities into a single function, and disables WoL for all
other ports on the device except for port A.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove the code that reads part_num from the EEPROM. This part number
is never displayed or queryable by the user.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Memory leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: We
should free resources allocated for previous rings if following allocation
fails.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
irq leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: if
e1000_up fails in e1000_open() we do not free allocated irq
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disable aggressive clocking on esb2 with SERDES port as it causes
hardware problems.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allow NVM to setup LPLU for IGP2 and IGP3. Only IGP needs LPLU D3
disabled during init here.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Explicitly lock two more ethtool entry points completely instead
of the hardware reset only to prevent a race condition.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove pci ID 8086:1000 from the list fo supported devices. This device
has not functioned with the driver for very long (since v. 5.2.4!)
and we lack the resources to come with a substantial fix. There are only
few cards of this type out there.
Signed-off-by: Jeff Kirsher <Jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
A panic was reported when receiving 1522 size packets if using
the default MTU. we should set the initial rx buffer length to the
value that e1000changemtu sets so that we can receive any packet
that would not be dropped by LPE=0.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke.jan.h.kok@intel.com>
After removing the hardware CRC stripping which causes problems with
SOL and related issues, we need to compensate for this changed size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The original suggested fix for netpoll was found to be racy on SMP
kernels. While it is highly unlikely that this race would ever be seen
in the real world due to current netpoll usage models, we implemented
this updated fix to address concerns.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Use the new names.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the wrapper function skb_is_gso which can be used instead
of directly testing skb_shinfo(skb)->gso_size. This makes things a little
nicer and allows us to change the primary key for indicating whether an skb
is GSO (if we ever want to do that).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device ID's of the supported ICH8 LAN devices.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The workaround for the ich8 lock loss problem is only needed for
a very small amount of systems. This adds an option for the user
to disable the workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This hooks up the ich8 structure into the driver itself.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This implements the core new functions needed for ich8's internal
NIC. This includes:
* ich8 specific read/write code
* flash/nvm access code
* software semaphore flag functions
* 10/100 PHY (fe - no gigabit speed) support for low-end versions
* A workaround for a powerdown sequence problem discovered that
affects a small number of motherboard.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Hardware is reported to have problems with ERT. We disable it for
all hardware to make sure we are not seeing unexplainable user
problems.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We were not checking the return value of get_speed_and_duplex
properly, whih may contain an error value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
M88 rev 2 PHY needs a longer downshift to function properly. This adds
a much longer downshift counter for this specific device.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several e1000 adapters were not blinking correctly or inconsistently. This
patch cleans this up and makes them all behave the same as far as possible.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
CRC stripping is breaking SMBUS-connected BMC's. We disable this
feature to make it work. This fixes related bugs regarding SOL.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
A certain AMD64 bridge (8132) has an option to turn on write combining
which breaks our adapter. To circumvent this we need to flush every write.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We can take uninitialized values into account which minimizes code
and allows us to simplify the parameter checking code greatly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Changing a printk message to make clear that this message is originating
from e1000.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Smart Power Down is a power saving feature in newer e1000 hardware. We
disable it because it causes time to link to be long, but make it a
user choice.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
buffer_info is already filled at the end of this while() loop.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
e1000_suspend is called even when !CONFIG_PM. The non-PM code inside of it
is properly #ifdef'd. This fixes the compiler warnings when !CONFIG_PM.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
In relation to the irq work done earlier we also move the PHY powerup
and powerdown functions into separate functions and move the calls to
_close and _open, making the PHY stay in it's power state as long as
the device is _up.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
After studying the driver mac reset code it was found that there
were multiple race conditions possible to reset the unit twice or
bring it e1000_up() double. This fixes all occurences where the
driver needs to reset the mac.
We also remove irq requesting/releasing into _open and _close so
that while the device is _up we will never touch the irq's. This fixes
the double free irq bug that people saw.
To make sure that the watchdog task doesn't cause another race we let
it run as a non-scheduled task.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Ethtool was reporting that loopback failed randomly on esb2
systems. Upon study it was found that the phy manual was changed
with respect to the loopback mode bits. The new value fixes it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Having separate fields in sk_buff for TSO/UFO (tso_size/ufo_size) is not
going to scale if we add any more segmentation methods (e.g., DCCP). So
let's merge them.
They were used to tell the protocol of a packet. This function has been
subsumed by the new gso_type field. This is essentially a set of netdev
feature bits (shifted by 16 bits) that are required to process a specific
skb. As such it's easy to tell whether a given device can process a GSO
skb: you just have to and the gso_type field and the netdev's features
field.
I've made gso_type a conjunction. The idea is that you have a base type
(e.g., SKB_GSO_TCPV4) that can be modified further to support new features.
For example, if we add a hardware TSO type that supports ECN, they would
declare NETIF_F_TSO | NETIF_F_TSO_ECN. All TSO packets with CWR set would
have a gso_type of SKB_GSO_TCPV4 | SKB_GSO_TCPV4_ECN while all other TSO
packets would be SKB_GSO_TCPV4. This means that only the CWR packets need
to be emulated in software.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a PCI bus error/fault triggers a PCI bus reset, attempts to get the
ethernet packet count statistics from the hardware will fail, returning
garbage data upstream. This patch skips statistics data collection if the
PCI device is not on the bus.
This patch presumes that an earlier patch,
[PATCH] PCI Error Recovery: e1000 network device driver
has already been applied.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a PCI bus error/fault triggers a PCI bus reset, attempts to get
the ethernet packet count statistics from the hardware will fail,
returning garbage data upstream. This patch skips statistics data
collection if the PCI device is not on the bus.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Various PCI bus errors can be signaled by newer PCI controllers.
This patch adds the PCI error recovery callbacks to the intel gigabit
ethernet e1000 device driver. The patch has been tested, and appears
to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures. Remove them for now. We'll let them
stay in mm for a while, or find a better solution to enable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.
This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
(cherry picked from c653e6351e commit)
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Seems there was a bit of a fix needed to due a bad merge in the legacy
receive path. Fixes a panic due to skb_over_panic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
