Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
DMA is set to use burst mode also for source channel. It should
descrease memory bandwidth needs.
DMA synchronization is set to use prefetch mechanism. SHAM block is behind
L4 bus and it doesn't have fifo. SHAM block is stalling as long as the new
data is available. It takes time to fetch data from memory and transfer it
via L4 bus. With prefetch enabled, data is waiting in DMA fifo and SHAM block
receives new data block faster.
This increases SHA processing speed up to 30 percent depending on the
bus / memory load.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
warning: (ZCRYPT && CRYPTO && CRYPTO_HW && S390 && ZCRYPT=y) selects
ZCRYPT_MONOLITHIC which has unmet direct dependencies (ZCRYPT=m)
ZCRYPT_MONOLITHIC should not depend on ZCRYPT="m" when it gets
selected if ZCRYPT="y".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
IXP4xx: Fix LL debugging on little-endian CPU.
IXP4xx: Fix sparse warnings in I/O primitives.
IXP4xx: Make mdio_bus struct static in the Ethernet driver.
IXP4xx: Fix ixp4xx_crypto little-endian operation.
IXP4xx: Prevent HSS transmitter lockup by disabling FRaMe signals.
ixp4xx/vulcan: add PCI support
ixp4xx: base support for Arcom Vulcan
Commit id 1636f8ac2b (sparc/of: Move
of_device fields into struct pdev_archdata) missed fixing up the
n2_core.c and greth.c drivers. This patch makes the required changes.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (39 commits)
random: Reorder struct entropy_store to remove padding on 64bits
padata: update API documentation
padata: Remove padata_get_cpumask
crypto: pcrypt - Update pcrypt cpumask according to the padata cpumask notifier
crypto: pcrypt - Rename pcrypt_instance
padata: Pass the padata cpumasks to the cpumask_change_notifier chain
padata: Rearrange set_cpumask functions
padata: Rename padata_alloc functions
crypto: pcrypt - Dont calulate a callback cpu on empty callback cpumask
padata: Check for valid cpumasks
padata: Allocate cpumask dependend recources in any case
padata: Fix cpu index counting
crypto: geode_aes - Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
pcrypt: Added sysfs interface to pcrypt
padata: Added sysfs primitives to padata subsystem
padata: Make two separate cpumasks
padata: update documentation
padata: simplify serialization mechanism
padata: make padata_do_parallel to return zero on success
padata: Handle empty padata cpumasks
...
Both of_bus_type and of_platform_bus_type are just #define aliases
for the platform bus. This patch removes all references to them and
switches to the of_register_platform_driver()/of_unregister_platform_driver()
API for registering.
Subsequent patches will convert each user of of_register_platform_driver()
into plain platform_drivers without the of_platform_driver shim. At which
point the of_register_platform_driver()/of_unregister_platform_driver()
functions can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
In function sg_copy_end_to_buffer, too much data
is copied when a segment in the scatterlist
has .length greater than the requested copy length.
This patch adds the limit checks to fix this bug of over copying,
which affected only the ahash algorithms.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The below patch gets rid of an unused variable ctx reported by
GCC when building the kernel.
CC [M] drivers/crypto/hifn_795x.o
drivers/crypto/hifn_795x.c: In function 'hifn_flush':
drivers/crypto/hifn_795x.c:2021:23: warning: variable 'ctx' set but not used
drivers/crypto/hifn_795x.c: In function 'hifn_process_queue':
drivers/crypto/hifn_795x.c:2142:23: warning: variable 'ctx' set but not used
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Correct ahash_process_req() to properly handle cases
where the total hash amount is a multiple of the blocksize.
The SEC must have some data to hash during the very last
descriptor operation; so up to one whole blocksize
of data is buffered until the final hash.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes the following on IXP425 little-endian:
NPE-C: firmware functionality 0x5, revision 0x2:1
alg: skcipher: Test 1 failed on encryption for ecb(des)-ixp4xx
00000000: 01 23 45 67 89 ab cd e7
alg: skcipher: Test 1 failed on encryption for ecb(des3_ede)-ixp4xx
00000000: 73 6f 6d 65 64 61 74 61
alg: skcipher: Test 1 failed on encryption for ecb(aes)-ixp4xx
00000000: 00 11 22 33 44 55 66 77 88 99 aa bb cc dd ee ff
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Acked-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
The error handling in mv_probe() was a bit messed up. There were some
gotos to the wrong labels so it ended up releasing stuff that that hadn't
been aquired and not releasing stuff that was meant to be released. I
shuffled it around a bit to fix it and make it clearer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
One note is that, unlike with non-HMAC hashes, we can't support
hmac(sha224) using the HMAC_SHA256 opcode.
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the ahash ->digest() ops do essentially the same thing, just
using different parameters.
So instead, have a single n2_hash_async_digest() and use an
n2_ahash_alg container that provides the parameters.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this by putting the async fallback request at the end of an n2
specific ahash request context, then properly adjusting the request
private size in our ahash ->cra_init().
We also need to put the writable state bits into the n2 request
private instead of the n2 cra_ctx.
With help from Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
SEC h/w versions 2.1 and above support sha224 via explicit instruction.
Performing sha224 ahashes on earlier versions is still possible because
they support sha256 (sha224 is sha256 with different initial constants
and a different truncation length). We do this by overriding hardware
context self-initialization, and perform it manually in s/w instead.
Thanks to Lee for his fixes for correct execution on actual sec2.0 h/w.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off by: Lee Nipper <lee.nipper@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the following alorithms to talitos:
md5,
sha1,
sha256,
sha384,
sha512.
These are all type ahash.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Acked-By: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Used talitos_alg_template in talitos_crypto_alg
so that it will accommodate ahash algorithms.
Added some preparation code for ahash allocation and removal.
No actual algorithms yet.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Acked-By: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No functional changes.
Use a union in talitos_alg_template for the crypto_alg
so that we can add a member later for ahash_alg.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Acked-By: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Current deficiencies:
1) No HMAC hash support yet.
2) Although the algs are registered as ASYNC they always run
synchronously.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is in preparation for the generic ablkcipher_walk helpers that
will be added to the crypto layer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Earlier kernel contained omap sha1 and md5 driver, which was not maintained,
was not ported to new crypto APIs and removed from the source tree.
- implements async crypto API using dma and cpu.
- supports multiple sham instances if available
- hmac
- concurrent requests
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fixes some code style issues like:
- Use #include <linux/io.h> instead of <asm/io.h> and #include
<linux/delay.h> instead of <asm/delay.h>
- Use "foo *bar" instead of "foo * bar"
- Add a space after the for or while sentence and before the open
parenthesis '('
- Don't use assignments in a if condition
Signed-off-by: Chihau Chau <chihau@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support processing of data from previous requests (as in hashing
update/final requests).
Signed-off-by: Uri Simchoni <uri@jdland.co.il>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make the copy-back of data optional (not done in hashing requests)
Signed-off-by: Uri Simchoni <uri@jdland.co.il>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Execute some code via function pointers rathr than direct calls
(to allow customization in the hashing request)
Signed-off-by: Uri Simchoni <uri@jdland.co.il>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enqueue generic async requests rather than ablkcipher requests
in the driver's queue
Signed-off-by: Uri Simchoni <uri@jdland.co.il>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix for situations where the source scatterlist spans more data than the
request nbytes
Signed-off-by: Uri Simchoni <uri@jdland.co.il>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Bugfix for situations where the destination scatterlist has a different
buffer structure than the source scatterlist (e.g. source has one 2K
buffer and dest has 2 1K buffers)
Signed-off-by: Uri Simchoni <uri@jdland.co.il>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Some misspelled occurences of 'octet' and some comments were also fixed
as I was on it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
a crypto_cipher cip member was set where a crypto_cipher blk members
should have been.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As the padlock driver for SHA uses a software fallback to perform
partial hashing, it must implement custom import/export functions.
Otherwise hmac which depends on import/export for prehashing will
not work with padlock-sha.
Reported-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
From: Márton Németh <nm127@freemail.hu>
The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The fallback code in cipher mode touch the union fallback.blk instead
of fallback.cip. This is wrong because we use the cipher and not the
blockcipher. This did not show any side effects yet because both types /
structs contain the same element right now.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
This patch updates misc percpu related symbols such that percpu
symbols are unique and don't clash with local symbols. This serves
two purposes of decreasing the possibility of global percpu symbol
collision and allowing dropping per_cpu__ prefix from percpu symbols.
* drivers/crypto/padlock-aes.c: s/last_cword/paes_last_cword/
* drivers/lguest/x86/core.c: s/last_cpu/lg_last_cpu/
* drivers/s390/net/netiucv.c: rename the variable used in a macro to
avoid clashing with percpu symbol
* arch/mn10300/kernel/kprobes.c: replace current_ prefix with cur_ for
static variables. Please note that percpu symbol current_kprobe
can't be changed as it's used by generic code.
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
The PadLock hardware requires the output buffer for SHA to be
128-bit aligned. We currentply place the buffer on the stack,
and ask gcc to align it to 128 bits. That doesn't work on i386
because the kernel stack is only aligned to 32 bits. This patch
changes the code to align the buffer by hand so that the hardware
doesn't fault on unaligned buffers.
Reported-by: Séguier Régis <rguier@e-teleport.net>
Tested-by: Séguier Régis <rguier@e-teleport.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enabling extended addressing in the h/w requires we always assign the
extended address component (eptr) of the talitos h/w pointer. This is
for e500 based platforms with large memories.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
align channel access locks onto separate cache lines (for performance
reasons). This is done by placing per-channel variables into their own
private struct, and using the cacheline_aligned attribute within that
struct.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
don't do request->src vs. assoc pointer math - it's the same as adding
assoclen and ivsize (just with more effort).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds support for Marvell's Cryptographic Engines and Security
Accelerator (CESA) which can be found on a few SoC.
Tested with dm-crypt.
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we encounter partial blocks in finup, we'll invoke the xsha
instruction with a bogus count that is not a multiple of the block
size. This patch fixes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The previous change to allow hashing from states other than the
initial broke compilation on i386 because the inline assembly
tried to squeeze a u64 into a 32-bit register. As we've already
checked for 32-bit overflows we can simply truncate it to u32,
or unsigned long so that we don't truncate at all on x86-64.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto4xx SHA implementation keeps the hash state in the tfm
data structure. This breaks a fundamental requirement of ahash
implementations that they must be reentrant.
This patch disables the broken implementation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch changes crypto4xx to use the new style ahash type.
In particular, we now use ahash_alg to define ahash algorithms
instead of crypto_alg.
This is achieved by introducing a union that encapsulates the
new type and the existing crypto_alg structure. They're told
apart through a u32 field containing the type value.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch makes crypto4xx use crypto_ahash_set_reqsize to avoid
accessing crypto_ahash directly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts the padlock-sha implementation to shash.
In doing so the existing mechanism of storing the data until
final is no longer viable as we do not have a way of allocating
data in crypto_shash_init and then reliably freeing it.
This is just as well because a better way of handling the problem
is to hash everything but the last chunk using normal sha code
and then provide the intermediate result to the padlock device.
This is good enough because the primary application of padlock-sha
is IPsec and there the data is laid out in the form of an hmac
header followed by the rest of the packet. In essence we can
provide all the data to the padlock as the hmac header only needs
to be hashed once.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extend previous workarounds for the prefetch bug to cover CBC mode,
clean up the code a bit.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The VIA Nano processor has a bug that makes it prefetch extra data
during encryption operations, causing spurious page faults. Extend
existing workarounds for ECB mode to copy the data to an temporary
buffer to avoid the problem.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The remove member of the pci_driver hifn_pci_driver uses __devexit_p(),
so the remove function itself should be marked with __devexit. And where
there be __devexit on the remove, so is there __devinit on the probe.
Similarly, the module_init/module_exit functions should be declared with
plain __init/__exit markings, not the hotplug __dev{init,exit} ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we added 64-bit support to padlock the dependency on x86
was lost. This causes build failures on non-x86 architectures.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Almost everything stays the same, we need just to use the extended registers
on the bit variant.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
the ICV check bit only gets set in decrypt entry points
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add these ablkcipher algorithms:
cbc(aes),
cbc(des3_ede).
Added handling of chained scatterlists with zero length entry
because eseqiv uses it.
Added new map and unmap routines.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch is preparation for adding new algorithm types.
Some elements which are AEAD specific were renamed.
The algorithm template structure was changed to
use crypto_alg, and talitos_alg_alloc was made
more general with respect to algorithm types.
ipsec_esp_edesc is renamed to talitos_edesc
to use it in the upcoming ablkcipher routines.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: padlock - Revert aes-all alias to aes
crypto: api - Fix algorithm module auto-loading
crypto: eseqiv - Fix IV generation for sync algorithms
crypto: ixp4xx - check firmware for crypto support
Since the padlock-aes driver doesn't require a fallback (it's
only padlock-sha that does), it should use the aes alias rather
than aes-all so that ones that do need a fallback can use it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- the loaded firmware may not support crypto at all or
only support DES and 3DES but not AES or
support DES, 3DES and AES.
- in case of no crypto support of the firmware, the module load will fail.
- in case of missing AES support, the AES algorithms are not registered
and a warning is printed during module load.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ixp4xx - Fix handling of chained sg buffers
crypto: shash - Fix unaligned calculation with short length
hwrng: timeriomem - Use phys address rather than virt
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- keep dma functions away from chained scatterlists.
Use the existing scatterlist iteration inside the driver
to call dma_map_single() for each chunk and avoid dma_map_sg().
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Tested-By: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (29 commits)
crypto: sha512-s390 - Add missing block size
hwrng: timeriomem - Breaks an allyesconfig build on s390:
nlattr: Fix build error with NET off
crypto: testmgr - add zlib test
crypto: zlib - New zlib crypto module, using pcomp
crypto: testmgr - Add support for the pcomp interface
crypto: compress - Add pcomp interface
netlink: Move netlink attribute parsing support to lib
crypto: Fix dead links
hwrng: timeriomem - New driver
crypto: chainiv - Use kcrypto_wq instead of keventd_wq
crypto: cryptd - Per-CPU thread implementation based on kcrypto_wq
crypto: api - Use dedicated workqueue for crypto subsystem
crypto: testmgr - Test skciphers with no IVs
crypto: aead - Avoid infinite loop when nivaead fails selftest
crypto: skcipher - Avoid infinite loop when cipher fails selftest
crypto: api - Fix crypto_alloc_tfm/create_create_tfm return convention
crypto: api - crypto_alg_mod_lookup either tested or untested
crypto: amcc - Add crypt4xx driver
crypto: ansi_cprng - Add maintainer
...
There is another user of IXP4xx queue manager, fix it.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With the mandatory algorithm testing at registration, we have
now created a deadlock with algorithms requiring fallbacks.
This can happen if the module containing the algorithm requiring
fallback is loaded first, without the fallback module being loaded
first. The system will then try to test the new algorithm, find
that it needs to load a fallback, and then try to load that.
As both algorithms share the same module alias, it can attempt
to load the original algorithm again and block indefinitely.
As algorithms requiring fallbacks are a special case, we can fix
this by giving them a different module alias than the rest. Then
it's just a matter of using the right aliases according to what
algorithms we're trying to find.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds support for AMCC ppc4xx security device driver. This is the
initial release that includes the driver framework with AES and SHA1 algorithms
support.
The remaining algorithms will be released in the near future.
Signed-off-by: James Hsiao <jhsiao@amcc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts the S390 sha algorithms to the new shash interface.
With fixes by Jan Glauber.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Previous commit for interrupt mitigation moved the done interrupt
acknowlegement from the isr to the talitos_done tasklet.
This patch moves the done interrupt acknowledgement back
into the isr so that done interrupts will always be acknowledged.
This covers the case for acknowledging interrupts for channel done processing
that has actually already been completed by the tasklet prior to fielding
a pending interrupt.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Base versions handle constant folding just fine.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use KM_SOFTIRQ instead of KM_IRQ in tasklet context.
Added bug_on on input no-page condition.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix queue management. Change ring size and perform its check not
one after another descriptor, but using stored pointers to the last
checked descriptors.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HIFN uses the transform context to store per-request data, which breaks
when more than one request is outstanding. Move per request members from
struct hifn_context to a new struct hifn_request_context and convert
the code to use this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Resetting the control word is quite expensive. Fortunately this
isn't an issue for the common operations such as CBC and ECB as
the whole operation is done through a single call. However, modes
such as LRW and XTS have to call padlock over and over again for
one operation which really hurts if each call resets the control
word.
This patch uses an idea by Sebastian Siewior to store the last
control word used on a CPU and only reset the control word if
that changes.
Note that any task switch automatically resets the control word
so we only need to be accurate with regard to the stored control
word when no task switches occur.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In commit ec6644d632 "crypto: talitos - Preempt
overflow interrupts", the test in atomic_inc_not_zero was interpreted by the
author to be applied after the increment operation (not before). This off-by-one
fix prevents overflow error interrupts from occurring when requests are frequent
and large enough to do so.
Signed-off-by: Vishnu Suresh <Vishnu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC version 2.1 and above adds the capability to do the IPSec ICV
memcmp in h/w. Results of the cmp are written back in the descriptor
header, along with the done status. A new callback is added that
checks these ICCR bits instead of performing the memcmp on the core,
and is enabled by h/w capability.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
After testing on different parts, another condition was added
before using h/w auth check because different
SEC revisions require different handling.
The SEC 3.0 allows a more flexible link table where
the auth data can span separate link table entries.
The SEC 2.4/2.1 does not support this case.
So a test was added in the decrypt routine
for a fragmented case; the h/w auth check is disallowed for
revisions not having the extent in the link table;
in this case the hw auth check is done by software.
A portion of a previous change for SEC 3.0 link table handling
was removed since it became dead code with the hw auth check supported.
This seems to be the best compromise for using hw auth check
on supporting SEC revisions; it keeps the link table logic
simpler for the fragmented cases.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In talitos_interrupt, upon one done interrupt, mask further done interrupts,
and ack only any error interrupt.
In talitos_done, unmask done interrupts after completing processing.
In flush_channel, ack each done channel processed.
Keep done overflow interrupts masked because even though each pkt
is ack'ed, a few done overflows still occur.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since we ack early, the re-read interrupt status in talitos_error
may be already updated with a new value. Pass the error ISR value
directly in order to report and handle the error based on the correct
error status.
Also remove unused error tasklet.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On Tue, Sep 23, 2008 at 08:06:32PM +0200, Dimitri Puzin (max@psycast.de) wrote:
> With this patch applied it still doesn't work as expected. The overflow
> messages are gone however syslog shows
> [ 120.924266] hifn0: abort: c: 0, s: 1, d: 0, r: 0.
> when doing cryptsetup luksFormat as in original e-mail. At this point
> cryptsetup hangs and can't be killed with -SIGKILL. I've attached
> SysRq-t dump of this condition.
Yes, I was wrong with the patch: HIFN does not support 64-bit addresses
afaics.
Attached patch should not allow HIFN to be registered on 64-bit arch, so
crypto layer will fallback to the software algorithms.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
talitos_remove() can be called from talitos_probe() on failure
exit path, so it can't be __devexit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SEC's h/w IV out implementation DMAs the trailing encrypted payload
block of the last encryption to ctx->iv. Since the last encryption may
still be pending completion, we can sufficiently prevent successive
packets from being transmitted with the same IV by xoring with sequence
number.
Also initialize alg_list earlier to prevent oopsing on a failed probe.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Wolfgang Walter reported this oops on his via C3 using padlock for
AES-encryption:
##################################################################
BUG: unable to handle kernel NULL pointer dereference at 000001f0
IP: [<c01028c5>] __switch_to+0x30/0x117
*pde = 00000000
Oops: 0002 [#1] PREEMPT
Modules linked in:
Pid: 2071, comm: sleep Not tainted (2.6.26 #11)
EIP: 0060:[<c01028c5>] EFLAGS: 00010002 CPU: 0
EIP is at __switch_to+0x30/0x117
EAX: 00000000 EBX: c0493300 ECX: dc48dd00 EDX: c0493300
ESI: dc48dd00 EDI: c0493530 EBP: c04cff8c ESP: c04cff7c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Process sleep (pid: 2071, ti=c04ce000 task=dc48dd00 task.ti=d2fe6000)
Stack: dc48df30 c0493300 00000000 00000000 d2fe7f44 c03b5b43 c04cffc8 00000046
c0131856 0000005a dc472d3c c0493300 c0493470 d983ae00 00002696 00000000
c0239f54 00000000 c04c4000 c04cffd8 c01025fe c04f3740 00049800 c04cffe0
Call Trace:
[<c03b5b43>] ? schedule+0x285/0x2ff
[<c0131856>] ? pm_qos_requirement+0x3c/0x53
[<c0239f54>] ? acpi_processor_idle+0x0/0x434
[<c01025fe>] ? cpu_idle+0x73/0x7f
[<c03a4dcd>] ? rest_init+0x61/0x63
=======================
Wolfgang also found out that adding kernel_fpu_begin() and kernel_fpu_end()
around the padlock instructions fix the oops.
Suresh wrote:
These padlock instructions though don't use/touch SSE registers, but it behaves
similar to other SSE instructions. For example, it might cause DNA faults
when cr0.ts is set. While this is a spurious DNA trap, it might cause
oops with the recent fpu code changes.
This is the code sequence that is probably causing this problem:
a) new app is getting exec'd and it is somewhere in between
start_thread() and flush_old_exec() in the load_xyz_binary()
b) At pont "a", task's fpu state (like TS_USEDFPU, used_math() etc) is
cleared.
c) Now we get an interrupt/softirq which starts using these encrypt/decrypt
routines in the network stack. This generates a math fault (as
cr0.ts is '1') which sets TS_USEDFPU and restores the math that is
in the task's xstate.
d) Return to exec code path, which does start_thread() which does
free_thread_xstate() and sets xstate pointer to NULL while
the TS_USEDFPU is still set.
e) At the next context switch from the new exec'd task to another task,
we have a scenarios where TS_USEDFPU is set but xstate pointer is null.
This can cause an oops during unlazy_fpu() in __switch_to()
Now:
1) This should happen with or with out pre-emption. Viro also encountered
similar problem with out CONFIG_PREEMPT.
2) kernel_fpu_begin() and kernel_fpu_end() will fix this problem, because
kernel_fpu_begin() will manually do a clts() and won't run in to the
situation of setting TS_USEDFPU in step "c" above.
3) This was working before the fpu changes, because its a spurious
math fault which doesn't corrupt any fpu/sse registers and the task's
math state was always in an allocated state.
With out the recent lazy fpu allocation changes, while we don't see oops,
there is a possible race still present in older kernels(for example,
while kernel is using kernel_fpu_begin() in some optimized clear/copy
page and an interrupt/softirq happens which uses these padlock
instructions generating DNA fault).
This is the failing scenario that existed even before the lazy fpu allocation
changes:
0. CPU's TS flag is set
1. kernel using FPU in some optimized copy routine and while doing
kernel_fpu_begin() takes an interrupt just before doing clts()
2. Takes an interrupt and ipsec uses padlock instruction. And we
take a DNA fault as TS flag is still set.
3. We handle the DNA fault and set TS_USEDFPU and clear cr0.ts
4. We complete the padlock routine
5. Go back to step-1, which resumes clts() in kernel_fpu_begin(), finishes
the optimized copy routine and does kernel_fpu_end(). At this point,
we have cr0.ts again set to '1' but the task's TS_USEFPU is stilll
set and not cleared.
6. Now kernel resumes its user operation. And at the next context
switch, kernel sees it has do a FP save as TS_USEDFPU is still set
and then will do a unlazy_fpu() in __switch_to(). unlazy_fpu()
will take a DNA fault, as cr0.ts is '1' and now, because we are
in __switch_to(), math_state_restore() will get confused and will
restore the next task's FP state and will save it in prev tasks's FP state.
Remember, in __switch_to() we are already on the stack of the next task
but take a DNA fault for the prev task.
This causes the fpu leakage.
Fix the padlock instruction usage by calling them inside the
context of new routines irq_ts_save/restore(), which clear/restore cr0.ts
manually in the interrupt context. This will not generate spurious DNA
in the context of the interrupt which will fix the oops encountered and
the possible FPU leakage issue.
Reported-and-bisected-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Later SEC revision requires the link table (used for scatter/gather)
to have an extra entry to account for the total length in descriptor [4],
which contains cipher Input and ICV.
This only applies to decrypt, not encrypt.
Without this change, on 837x, a gather return/length error results
when a decryption uses a link table to gather the fragments.
This is observed by doing a ping with size of 1447 or larger with AES,
or a ping with size 1455 or larger with 3des.
So, add check for SEC compatible "fsl,3.0" for using extra link table entry.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
free edescriptor when returning error (such as -EAGAIN).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
use GFP_ATOMIC when necessary; use atomic_t when allocating submit_count.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
add requests pending/submit count to prevent request queue full
condition by preempting h/w overflow interrupts in software.
We do this due to the delay in the delivery and handling of the
channel overflow error interrupt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Seems that dst == src, but this fixes the logic in case it's not.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove of_node_put calls since there is no corresponding of_node_get.
This patch prevents an exception when talitos is loaded a 2nd time.
This sequence: modprobe talitos; rmmod talitos; modprobe talitos
causes this message: "WARNING: Bad of_node_put() on /soc8349@e0000000/crypto@30000".
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Without CRYPTO_AUTHENC the driver fails to build:
drivers/built-in.o: In function `ixp_module_init':
ixp4xx_crypto.c:(.init.text+0x3250): undefined reference to `crypto_aead_type'
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds support for:
authenc(hmac(sha256),cbc(aes)),
authenc(hmac(sha256),cbc(des3_ede)),
authenc(hmac(md5),cbc(aes)),
authenc(hmac(md5),cbc(des3_ede)).
Some constant usage was changed to use aes, des, and sha include files.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The name authenc(hmac(sha1-talitos),cbc(aes-talitos)) is potentially
ambiguous since it could also mean using the generic authenc template
on hmac(sha1-talitos) and cbc(aes-talitos). In general, parentheses
should be reserved for templates that spawn algorithms.
This patches changes it to the form authenc-hmac-sha1-cbc-aes-talitos.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds support for authenc(hmac(sha1),cbc(des3_ede))
to the talitos crypto driver for the Freescale Security Engine.
Some adjustments were made to the scatterlist to link table conversion
to make 3des work for ping -s 1439..1446.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When loading aes or sha256 via the module aliases, the padlock modules
also try to get loaded. Make the error message for them not being
present only be a NOTICE rather than an ERROR so that use of 'quiet'
will suppress the messages
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the hardware crypto engine provided by the NPE C
of the Intel IXP4xx networking processor series.
Supported ciphers: des, des3, aes
and a combination of them with md5 and sha1 hmac
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the SEC available on a wide range of PowerQUICC devices,
e.g. MPC8349E, MPC8548E.
This initial version supports authenc(hmac(sha1),cbc(aes)) for use with IPsec.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The descriptors need to be invalidated after processing for ring
cleanup to work properly and to avoid using an old destination
descriptor when the src and cmd descriptors are already set up
and the dst descriptor isn't.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move command descriptor setup to seperate function as preparation
for the following DMA setup fixes.
Note 1: also fix a harmless typo while moving it: sa_idx is initialized
to dma->resi instead of dma->cmdi.
Note 2: errors from command descriptor setup are not propagated back,
anymore, they can't be handled anyway and all conditions leading
to errors should be checked earlier.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
All but the last element of the command and result descriptor rings can be
used for crypto requests, fix HIFN_QUEUE_LENGTH.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For combined modes like cbc(aes) the driver is responsible for
initializing ivsize.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the CryptoAPI instantiates a new algorithm, it performs a lookup
by driver name. Since hifn uses the same name for all modes of one
algorithm, the lookup may return an incorrect algorithm.
Change the name to use <mode>-<algo>-<devicename> to provide unique
names for the different combinations and devices.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The scatterlist may contain more data than the crypto request, causing
an underflow of the remaining byte count while walking the list.
Use the minimum of the scatterlist element size and the remaining byte
count specified in the crypto request to avoid this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The check for misalignment of the scatterlist data has two bugs:
- the source buffer doesn't need to be aligned at all
- the destination buffer and its size needs to be aligned to a multiple
of 4, not to the crypto alg blocksize
Introduce symbolic constant for destination buffer alignment requirements,
use it instead of the crypto alg blocksize and remove the unnecessary
checks for source buffer alignment and change cra_alignmask to zero.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ablkcipher_walk may return a negative error value, handle this properly
instead of treating it as a huge number of scatter-gather elements.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hifn_setup_crypto() needs to return -EINPROGRESS on success to indicate
asynchronous processing to the crypto API. This also means it must not
return the errno code returned by hifn_process_queue(), if any.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Without debugging this spams the log with "printk: N messages surpressed"
without any actual messages on error. With debugging its more useful to
always see the message.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HIFN uses little-endian by default, move cpu_to_le32 conversion to hifn_write_0/
hifn_write_1, add sparse annotations and fix an invalid endian conversion in
hifn_setup_src_desc.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Padlock AES setkey routine is the same as exported by the generic
implementation. So we could use it.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Cc: Michal Ludvig <michal@logix.cz>
Tested-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
