Now we cannot distinguish that one sk is a udp or sctp style when
we use ss to dump sctp_info. it's necessary to dump it as well.
For sctp_diag, ss support is not officially available, thus there
are no official users of this yet, so we can add this field in the
middle of sctp_info without breaking user API.
v1->v2:
- move 'sctpi_s_type' field to the end of struct sctp_info, so
that it won't cause incompatibility with applications already
built.
- add __reserved3 in sctp_info to make sure sctp_info is 8-byte
alignment.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dirty_tx isn't updated, then dma_unmap_single
can be called twice.
This fixes a
[ 58.420980] ------------[ cut here ]------------
[ 58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[ 58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]
encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address of the physical interface is only copied to the VLAN
when it is first created, resulting in an inconsistency after MAC
address changes of only newly created VLANs having an up-to-date MAC.
The VLANs should continue inheriting the MAC address of the physical
interface until the VLAN MAC address is explicitly set to any value.
This allows IPv6 EUI64 addresses for the VLAN to reflect any changes
to the MAC of the physical interface and thus for DAD to behave as
expected.
Signed-off-by: Mike Manning <mmanning@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iadev->rx_open[] array holds "iadev->num_vc" pointers (this code
assumes that pointers are 32 bits). So the > here should be >= or else
we could end up reading a garbage pointer from one element beyond the
end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug was there when the driver was first added in back in year 2000.
It causes a Smatch warning:
drivers/atm/firestream.c:849 process_incoming()
error: buffer overflow 'res_strings' 60 <= 63
There are supposed to be 64 entries in this array and the missing
strings are clearly in the 30 40 range. I added them as reserved 37 to
reserved 40. It's possible that strings are really supposed to be added
in the middle instead of at the end, but this approach is safe, in that
it fixes the bug and doesn't break anything that wasn't already broken.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_OBJECTS_TIMERS=y, hrtimer_init_on_stack() requires
a matching call to destroy_hrtimer_on_stack() to clean up timer
debug objects.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
hrtimer_init_on_stack() needs a matching call to
destroy_hrtimer_on_stack(), so both need to be exported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings the PER_LINUX32 /proc/cpuinfo format more in line with
the 32-bit ARM one by providing an additional line:
model name : ARMv8 Processor rev X (v8l)
Cc: <stable@vger.kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Replace explicit computation of vma page count by a call to
vma_pages().
Also, include <linux/mm.h>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
The members child_list and active_list were added to the fence struct
without descriptions for the Documentation. Adding these.
Fixes: b55b54b5db ("staging/android: remove struct sync_pt")
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Split out dma-buf related parts into their own section, add missing
files, and write a bit of overview about how it all fits together.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Pull s390 fixes from Martin Schwidefsky:
"Three bugs fixes and an update for the default configuration"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix info leak in do_sigsegv
s390/config: update default configuration
s390/bpf: fix recache skb->data/hlen for skb_vlan_push/pop
s390/bpf: reduce maximum program size to 64 KB
Apparently nobody noticed that dma-buf.h wasn't actually pulled into
docbook build. And as a result the headerdoc comments bitrot a bit.
Add missing params/fields.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
- Drop the lock before reading out the GPIO direction
setting in drivers supporting the .get_direction()
callback: some of them may be slowpath.
- Flush GPIO direction setting before locking a GPIO as an
IRQ: some electronics or other poking around in the
registers behind our back may have happened, so flush
the direction status before trying to lock the line for
use by IRQs.
- Bail out silently when asked to perform operations on
NULL GPIO descriptors. That is what all the get_*_optional()
is about: we get optional GPIO handles, if they are not
there, we get NULL.
- Handle compatible ioctl() correctly: we need to convert
the ioctl() pointer using compat_ptr() here like everyone
else.
- Disable the broken .to_irq() on the LPC32xx platform.
The whole irqchip infrastructure was replaced in the
last merge window, and a new implementation will be
needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXTTtPAAoJEEEQszewGV1zOEIP/AuYXFdcjFDxHbx+DWdObNSh
XKvpbRliFDyjyGy/omXCUQg0tl0/2SD1wm+I8kMwfKRwmN1S8bt5wIrVEIOOHTwC
lZgj16qzJwS0exmAfRQ5ooQEmF3W8ZcN6aUOMlUy/uwgk8t0wbQPUChT9lSURgMw
qsGnL3ci0QnVbgCngAR6h964LAHYttyOa1scBD6naVQwgrO8g4ad/KiC38vu2z/d
eFsfrX8A5q9w/TS6Zz+Ue7RBBiZb4XRJ5dNsfgS4+W940NDCMq1F73cmE90Hzzs/
4Lx+56Y5cXJn8C90DM1kU/uVfdXU0XPA9R8CC4lT4sO6HSkWEW1ZcOrMpNXshJfZ
DR5h4W03WSD+QT6lZIt0kIo3xFWE/5HFS5xLLPPm2dOnNgwUSru7v0x82RWyClLl
NOVcxJ7rsgUXLc4J+zi+r+Lhtb+2cMuwt2PS8QISeSzYcSSOXmiqRrMsO0SKsr0h
JnEaCvC08Utm1RalATelmtoM4eIYl6kuODX14xdOI8hsvrSKeUF5cekzot6ivHO3
/w286hovt102j51F3wMxRuAOmL5S3GuoypQBiNNDOQhkyMLtuzcjfz//38RW5Ooo
CtoNbL59BnpR4zYT0Xdm5zPTHohJdC1B6/mANCuWZJM40IQ5VVoeJXEshdJ2YQe/
U5m25QNqer2Xm4GJYfGh
=5IlZ
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A bunch of GPIO fixes for the v4.7 series:
- Drop the lock before reading out the GPIO direction setting in
drivers supporting the .get_direction() callback: some of them may
be slowpath.
- Flush GPIO direction setting before locking a GPIO as an IRQ: some
electronics or other poking around in the registers behind our back
may have happened, so flush the direction status before trying to
lock the line for use by IRQs.
- Bail out silently when asked to perform operations on NULL GPIO
descriptors. That is what all the get_*_optional() is about: we
get optional GPIO handles, if they are not there, we get NULL.
- Handle compatible ioctl() correctly: we need to convert the ioctl()
pointer using compat_ptr() here like everyone else.
- Disable the broken .to_irq() on the LPC32xx platform. The whole
irqchip infrastructure was replaced in the last merge window, and a
new implementation will be needed"
* tag 'gpio-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: drop lock before reading GPIO direction
gpio: bail out silently on NULL descriptors
gpio: handle compatible ioctl() pointers
gpio: flush direction status in gpiochip_lock_as_irq()
gpio: lpc32xx: disable broken to_irq support
The GICv3 backend of the vgic is quite barrier heavy, in order
to ensure synchronization of the system registers and the
memory mapped view for a potential GICv2 guest.
But when the guest is using a GICv3 model, there is absolutely
no need to execute all these heavy barriers, and it is actually
beneficial to avoid them altogether.
This patch makes the synchonization conditional, and ensures
that we do not change the EL1 SRE settings if we do not need to.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Both our GIC emulations are "strict", in the sense that we either
emulate a GICv2 or a GICv3, and not a GICv3 with GICv2 legacy
support.
But when running on a GICv3 host, we still allow the guest to
tinker with the ICC_SRE_EL1 register during its time slice:
it can switch SRE off, observe that it is off, and yet on the
next world switch, find the SRE bit to be set again. Not very
nice.
An obvious solution is to always trap accesses to ICC_SRE_EL1
(by clearing ICC_SRE_EL2.Enable), and to let the handler return
the programmed value on a read, or ignore the write.
That way, the guest can always observe that our GICv3 is SRE==1
only.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When we trap ICC_SRE_EL1, we handle it as RAZ/WI. It would be
more correct to actual make it RO, and return the configured
value when read.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When reading back from the list registers, we need to perform
two actions for level interrupts:
1) clear the soft-pending bit if the interrupt is not pending
anymore *in the list register*
2) resample the line level and propagate it to the pending state
But these two actions shouldn't be linked, and we should *always*
resample the line level, no matter what state is in the list
register. Otherwise, we may end-up injecting spurious interrupts
that have been already retired.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When reading back from the list registers, we need to perform
two actions for level interrupts:
1) clear the soft-pending bit if the interrupt is not pending
anymore *in the list register*
2) resample the line level and propagate it to the pending state
But these two actions shouldn't be linked, and we should *always*
resample the line level, no matter what state is in the list
register. Otherwise, we may end-up injecting spurious interrupts
that have been already retired.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When saving the state of the list registers, it is critical to
reset them zero, as we could otherwise leave unexpected EOI
interrupts pending for virtual level interrupts.
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When saving the state of the list registers, it is critical to
reset them zero, as we could otherwise leave unexpected EOI
interrupts pending for virtual level interrupts.
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The SET_MODULE_RONX protections are effectively the same as the
DEBUG_RODATA protections we enabled by default back in commit
57efac2f71 ("arm64: enable CONFIG_DEBUG_RODATA by default"). It
seems unusual to have one but not the other.
As evidenced by the help text, the rationale appears to be that
SET_MODULE_RONX interacts poorly with tracing and patching, but both of
these make use of the insn framework, which takes SET_MODULE_RONX into
account. Any remaining issues are bugs which should be fixed regardless
of the default state of the option.
This patch enables DEBUG_SET_MODULE_RONX by default, and replaces the
help text with a new wording derived from the DEBUG_RODATA help text,
which better describes the functionality. Previously, the DEBUG_RODATA
entry was inconsistently indented with spaces, which are replaced with
tabs as with the other Kconfig entries.
Additionally, the wording of recommended defaults is made consistent for
all options. These are placed in a new paragraph, unquoted, as a full
sentence (with a period/full stop) as this appears to be the most common
form per $(git grep 'in doubt').
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit 12a0ef7b0a ("arm64: use generic strnlen_user and
strncpy_from_user functions"), the definition of __addr_ok() has been
languishing unused; eradicate the sucker.
CC: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We are already using the privileged versions of MMCR0, MMCR1
and MMCRA in the kernel, so for MMCR2, we should better use
the privileged versions, too, to be consistent.
Fixes: 240686c136 ("powerpc: Initialise PMU related regs on Power8")
Cc: stable@vger.kernel.org # v3.10+
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The SIAR and SDAR registers are available twice, one time as SPRs
780 / 781 (unprivileged, but read-only), and one time as the SPRs
796 / 797 (privileged, but read and write). The Linux kernel code
currently uses the unprivileged SPRs - while this is OK for reading,
writing to that register of course does not work.
Since the KVM code tries to write to this register, too (see the mtspr
in book3s_hv_rmhandlers.S), the contents of this register sometimes get
lost for the guests, e.g. during migration of a VM.
To fix this issue, simply switch to the privileged SPR numbers instead.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit ff7925848b.
Now that the contiguous-hint hugetlb regression has been debugged and
fixed upstream by 66ee95d16a ("mm: exclude HugeTLB pages from THP
page_mapped() logic"), we can revert the previous partial revert of this
feature.
Signed-off-by: Will Deacon <will.deacon@arm.com>
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Cc: stable@vger.kernel.org
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A lot of the display drivers for OMAP use the gpio descriptor functions
that are only available in linux/gpio.h if GPIOLIB is enabled and
otherwise produce a build error:
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c: In function 'opa362_enable':
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c:101:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-dpi.c: In function 'panel_dpi_probe_pdata':
drivers/gpu/drm/omapdrm/displays/panel-dpi.c:189:23: error: implicit declaration of function 'gpio_to_desc' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c: In function 'sharp_ls_enable':
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c:120:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
This replaces the existing linux/gpio.h with linux/gpio/consumer.h
where needed. In case of panel-lgphilips-lb035q02.c however, we
also have to include linux/gpio.h to get the definition of gpio_is_valid
and gpio_set_value_cansleep that are used for the non-DT case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: resolved conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver relies on this header to be included
implicitly, but this does not always work, and I get
this error in randconfig builds:
gpu/drm/omapdrm/dss/hdmi_phy.c: In function 'hdmi_phy_dump':
gpu/drm/omapdrm/dss/hdmi_phy.c:34:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_wp.c: In function 'hdmi_wp_dump':
gpu/drm/omapdrm/dss/hdmi_wp.c:26:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_pll.c: In function 'hdmi_pll_dump':
gpu/drm/omapdrm/dss/hdmi_pll.c:30:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
This adds the #include statements in all files that have
a seq_printf statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit 1c278e5e37.
If DRM_OMAP does not select OMAP2_DSS it is possible to build a kernel with
DRM_OMAP only and not selecting OMAP2_DSS. Since omapdrm depends on
OMAP2_DSS this will result on broken kernel build.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3dd regulator: Deprecate regulator_can_change_voltage()
describers it clearly.
Also, regulator_set_voltage() is misused in the driver, as it is
supposed to be used only in cases where the regulator voltage needs to
be changed dynamically at runtime. In DSS's case, we always want a fixed
voltage, set in the .dts files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DDC scl high and low times were set to the minimum values
from the i2c specification, but the i2c specification takes into
account the rise time and fall time to calculate the frequency.
To pass HDMI certification DDC can not exceed 100kHz therefore in
a system where the rise times and fall times are negligible the high
and low times for scl need to be 10us.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The AVI infoframe R0-R3 in the 2nd data byte represents the
Active Format Aspect Ratio. It is four bits long not two bits.
This fixes that mask used to extract the bits before writing the
bits to the hardware registers.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_core_powerdown_disable() is supposed to disable HDMI core's
power-down mode. However, the function sets the power-down bit to 0,
which means "enable power-down".
This hasn't caused any issues as the PD seems to affect only interrupts
from HDMI core, and none of those interrupts are used at the moment. CEC
functionality requires core interrupts, and the PD mode needs to be
fixed.
This patch fixes hdmi_core_powerdown_disable() to actually disable the
PD mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
With certain kernel config options many omapdrm files fail to compile
due to missing include of linux/gpio/consumer.h and linux/of.h.
This patch adds those includes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In some configurations, we can build the OMAP dss driver without
implictly including the pinctrl consumer definitions, causing
a build error:
gpu/drm/omapdrm/dss/dss.c: In function 'dss_runtime_suspend':
gpu/drm/omapdrm/dss/dss.c:1268:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
This adds an explicit #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While we are finishing a device replace operation we can have a concurrent
task trying to do a read repair operation, in which case it will call
btrfs_map_block() to get a struct btrfs_bio which can have a stripe that
points to the source device of the device replace operation. This allows
for the read repair task to dereference the stripe's device pointer after
the device replace operation has freed the source device, resulting in
an invalid memory access. This is similar to the problem solved by my
previous patch in the same series and named "Btrfs: fix race between
device replace and discard".
So fix this by surrounding the call to btrfs_map_block() and the code
that uses the returned struct btrfs_bio with calls to
btrfs_bio_counter_inc_blocked() and btrfs_bio_counter_dec(), giving the
proper serialization with the finishing phase of the device replace
operation.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
While we are finishing a device replace operation, we can make a discard
operation (fs mounted with -o discard) do an invalid memory access like
the one reported by the following trace:
[ 3206.384654] general protection fault: 0000 [#1] PREEMPT SMP
[ 3206.387520] Modules linked in: dm_mod btrfs crc32c_generic xor raid6_pq acpi_cpufreq tpm_tis psmouse tpm ppdev sg parport_pc evdev i2c_piix4 parport
processor serio_raw i2c_core pcspkr button loop autofs4 ext4 crc16 jbd2 mbcache sr_mod cdrom ata_generic sd_mod virtio_scsi ata_piix libata virtio_pci
virtio_ring scsi_mod e1000 virtio floppy [last unloaded: btrfs]
[ 3206.388595] CPU: 14 PID: 29194 Comm: fsstress Not tainted 4.6.0-rc7-btrfs-next-29+ #1
[ 3206.388595] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[ 3206.388595] task: ffff88017ace0100 ti: ffff880171b98000 task.ti: ffff880171b98000
[ 3206.388595] RIP: 0010:[<ffffffff8124d233>] [<ffffffff8124d233>] blkdev_issue_discard+0x5c/0x2a7
[ 3206.388595] RSP: 0018:ffff880171b9bb80 EFLAGS: 00010246
[ 3206.388595] RAX: ffff880171b9bc28 RBX: 000000000090d000 RCX: 0000000000000000
[ 3206.388595] RDX: ffffffff82fa1b48 RSI: ffffffff8179f46c RDI: ffffffff82fa1b48
[ 3206.388595] RBP: ffff880171b9bcc0 R08: 0000000000000000 R09: 0000000000000001
[ 3206.388595] R10: ffff880171b9bce0 R11: 000000000090f000 R12: ffff880171b9bbe8
[ 3206.388595] R13: 0000000000000010 R14: 0000000000004868 R15: 6b6b6b6b6b6b6b6b
[ 3206.388595] FS: 00007f6182e4e700(0000) GS:ffff88023fdc0000(0000) knlGS:0000000000000000
[ 3206.388595] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3206.388595] CR2: 00007f617c2bbb18 CR3: 000000017ad9c000 CR4: 00000000000006e0
[ 3206.388595] Stack:
[ 3206.388595] 0000000000004878 0000000000000000 0000000002400040 0000000000000000
[ 3206.388595] 0000000000000000 ffff880171b9bbe8 ffff880171b9bbb0 ffff880171b9bbb0
[ 3206.388595] ffff880171b9bbc0 ffff880171b9bbc0 ffff880171b9bbd0 ffff880171b9bbd0
[ 3206.388595] Call Trace:
[ 3206.388595] [<ffffffffa042899e>] btrfs_issue_discard+0x12f/0x143 [btrfs]
[ 3206.388595] [<ffffffffa042899e>] ? btrfs_issue_discard+0x12f/0x143 [btrfs]
[ 3206.388595] [<ffffffffa042e862>] btrfs_discard_extent+0x87/0xde [btrfs]
[ 3206.388595] [<ffffffffa04303b5>] btrfs_finish_extent_commit+0xb2/0x1df [btrfs]
[ 3206.388595] [<ffffffff8149c246>] ? __mutex_unlock_slowpath+0x150/0x15b
[ 3206.388595] [<ffffffffa04464c4>] btrfs_commit_transaction+0x7fc/0x980 [btrfs]
[ 3206.388595] [<ffffffff8149c246>] ? __mutex_unlock_slowpath+0x150/0x15b
[ 3206.388595] [<ffffffffa0459af6>] btrfs_sync_file+0x38f/0x428 [btrfs]
[ 3206.388595] [<ffffffff811a8292>] vfs_fsync_range+0x8c/0x9e
[ 3206.388595] [<ffffffff811a82c0>] vfs_fsync+0x1c/0x1e
[ 3206.388595] [<ffffffff811a8417>] do_fsync+0x31/0x4a
[ 3206.388595] [<ffffffff811a8637>] SyS_fsync+0x10/0x14
[ 3206.388595] [<ffffffff8149e025>] entry_SYSCALL_64_fastpath+0x18/0xa8
[ 3206.388595] [<ffffffff81100c6b>] ? time_hardirqs_off+0x9/0x14
[ 3206.388595] [<ffffffff8108e87d>] ? trace_hardirqs_off_caller+0x1f/0xaa
This happens because when we call btrfs_map_block() from
btrfs_discard_extent() to get a btrfs_bio structure, the device replace
operation has not finished yet, but before we use the device of one of the
stripes from the returned btrfs_bio structure, the device object is freed.
This is illustrated by the following diagram.
CPU 1 CPU 2
btrfs_dev_replace_start()
(...)
btrfs_dev_replace_finishing()
btrfs_start_transaction()
btrfs_commit_transaction()
(...)
btrfs_sync_file()
btrfs_start_transaction()
(...)
btrfs_commit_transaction()
btrfs_finish_extent_commit()
btrfs_discard_extent()
btrfs_map_block()
--> returns a struct btrfs_bio
with a stripe that has a
device field pointing to
source device of the replace
operation (the device that
is being replaced)
mutex_lock(&uuid_mutex)
mutex_lock(&fs_info->fs_devices->device_list_mutex)
mutex_lock(&fs_info->chunk_mutex)
btrfs_dev_replace_update_device_in_mapping_tree()
--> iterates the mapping tree and for each
extent map that has a stripe pointing to
the source device, it updates the stripe
to point to the target device instead
btrfs_rm_dev_replace_blocked()
--> waits for fs_info->bio_counter to go down to 0
btrfs_rm_dev_replace_remove_srcdev()
--> removes source device from the list of devices
mutex_unlock(&fs_info->chunk_mutex)
mutex_unlock(&fs_info->fs_devices->device_list_mutex)
mutex_unlock(&uuid_mutex)
btrfs_rm_dev_replace_free_srcdev()
--> frees the source device
--> iterates over all stripes
of the returned struct
btrfs_bio
--> for each stripe it
dereferences its device
pointer
--> it ends up finding a
pointer to the device
used as the source
device for the replace
operation and that was
already freed
So fix this by surrounding the call to btrfs_map_block(), and the code
that uses the returned struct btrfs_bio, with calls to
btrfs_bio_counter_inc_blocked() and btrfs_bio_counter_dec(), so that
the finishing phase of the device replace operation blocks until the
the bio counter decreases to zero before it frees the source device.
This is the same approach we do at btrfs_map_bio() for example.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Merge lib/uuid fixes from Andy Shevchenko.
* emailed patches from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
lib/uuid.c: use correct offset in uuid parser
lib/uuid: add a test module
Use '+ 0' and '+ 1' as offsets, like they were intended, instead of
adding to the result.
Fixes: 2b1b0d6670 ("lib/uuid.c: introduce a few more generic helpers")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears that somehow I missed a test of the latest UUID rework which
landed in the kernel. Present a small test module to avoid such cases
in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- missing selection in public_key that may result in a build failure
- Potential crash in error path in omap-sham
- ccp AES XTS bug that affects requests larger than 4096"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccp - Fix AES XTS error for request sizes above 4096
crypto: public_key: select CRYPTO_AKCIPHER
crypto: omap-sham - potential Oops on error in probe
Commit d30291b985 ("libceph: variable-sized ceph_object_id") changed
dout()s in what is now encode_request() and ceph_object_locator_to_pg()
to use %pE, mostly to document that, although all rbd and cephfs object
names are NULL-terminated strings, ceph_object_id will handle any RADOS
object name, including the one containing NULs, just fine.
However, it turns out that vbin_printf() can't handle anything but ints
and %s - all %p suffixes are ignored. The buffer %p** points to isn't
recorded, resulting in trash in the messages if the buffer had been
reused by the time bstr_printf() got to it.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
handle_reply() may be called twice on the same request: on ack and then
on commit. This occurs on btrfs-formatted OSDs or if cephfs sync write
path is triggered - CEPH_OSD_FLAG_ACK | CEPH_OSD_FLAG_ONDISK.
handle_reply() handles this with the help of done_request().
Fixes: 5aea3dcd50 ("libceph: a major OSD client update")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
For the benefit of every single caller, take osdc instead of map.
Also, now that osdc->osdmap can't ever be NULL, drop the check.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
When adding the gpiochip, the GPIO HW drivers' callback get_direction()
could get called in atomic context. Some of the GPIO HW drivers may
sleep when accessing the register.
Move the lock before initializing the descriptors.
Reported-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In fdeb8e1547
("gpio: reflect base and ngpio into gpio_device")
assumed that GPIO descriptors are either valid or error
pointers, but gpiod_get_[index_]optional() actually return
NULL descriptors and then all subsequent calls should just
bail out.
Cc: stable@vger.kernel.org
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes: fdeb8e1547 ("gpio: reflect base and ngpio into gpio_device")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we're using the compatible ioctl() we need to handle the
argument pointer in a special way or there will be trouble.
Fixes: 3c702e9987 ("gpio: add a userspace chardev ABI for GPIOs")
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>