Commit Graph

3 Commits

Author SHA1 Message Date
Benoit Parrot
dc28aa072f gpu:drm:tilcdc: get preferred_bpp value from DT
The preferred_bpp value in currently hard-coded to 16.
This causes color corruption on the am335x-evm lcd panel which
requires 32 bpp instead. This changes attempts to use the configured
bpp value from the DT or built-in panel-info struct.

Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2013-06-20 14:08:01 +10:00
Arnd Bergmann
a59e1ff3b8 drm/tilcdc: use only a single module device table
The tilcdc driver fails to be built as a module because of extraneous
MODULE_DEVICE_TABLE entries:

drivers/gpu/drm/tilcdc/tilcdc_slave.o:(.data+0x54): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
drivers/gpu/drm/tilcdc/tilcdc_panel.o:(.data+0x54): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
drivers/gpu/drm/tilcdc/tilcdc_drv.o:(.data+0x184): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here

Since the entire point of these entries is to make the module autoload
when one of the devices is present, it's enough to keep the one entry
for "ti,am33xx-tilcdc", which should always be there if any of the
others are.

Acked-by: Rob Clark <robdclark@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2013-04-26 10:18:46 +10:00
Rob Clark
16ea975eac drm/tilcdc: add TI LCD Controller DRM driver (v4)
A simple DRM/KMS driver for the TI LCD Controller found in various
smaller TI parts (AM33xx, OMAPL138, etc).  This driver uses the
CMA helpers.  Currently only the TFP410 DVI encoder is supported
(tested with beaglebone + DVI cape).  There are also various LCD
displays, for which support can be added (as I get hw to test on),
and an external i2c HDMI encoder found on some boards.

The display controller supports a single CRTC.  And the encoder+
connector are split out into sub-devices.  Depending on which LCD
or external encoder is actually present, the appropriate output
module(s) will be loaded.

v1: original
v2: fix fb refcnting and few other cleanups
v3: get +/- vsync/hsync from timings rather than panel-info, add
    option DT max-bandwidth field so driver doesn't attempt to
    pick a display mode with too high memory bandwidth, and other
    small cleanups
v4: remove some unneeded stuff from panel-info struct, properly
    set high bits for hfp/hsw/hbp for rev 2, add DT bindings docs

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
2013-02-19 17:57:44 -05:00