Make sure the device and the kernel are performing the multipath hash
according to the same parameters by updating the device whenever the
relevant netevent is generated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used the hardware's defaults for multipath hash
computation. This patch aligns the hardware's multipath parameters with
the kernel's.
For IPv4 packets, the parameters are determined according to the
'fib_multipath_hash_policy' sysctl during module initialization. In case
L3-mode is requested, only the source and destination IP addresses are
used. There is no special handling of ICMP error packets.
In case L4-mode is requested, a 5-tuple is used: source and destination
IP addresses, source and destination ports and IP protocol. Note that
the layer 4 fields are not considered for fragmented packets.
For IPv6 packets, the source and destination IP addresses are used, as
well as the flow label and the next header fields.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RECRv2 register is used for setting up the router's ECMP hash
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct containing the work item queued from the netevent handler is
named after the only event it is currently used for, which is neighbour
updates.
Use a more appropriate name for the struct, as we are going to use it
for more events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need to respond to netevents notifying us about
multipath hash updates by configuring the device's hash parameters.
Embed the netevent notifier in the router struct so that we could
retrieve it upon notifications and use it to configure the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
It fixes a problem for the last chunk where 'chunk_size' is smaller than
MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding
previous data.
Fixes: 6882b0aee1 ("mlxsw: Introduce support for I2C bus")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.
In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.
Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a FIB rule on a spectrum platform silently aborts FIB offload:
$ ip ru add pref 99 from all to 192.168.1.1 table 10
$ dmesg -c
[ 623.144736] mlxsw_spectrum 0000:03:00.0: FIB abort triggered. Note that FIB entries are no longer being offloaded to this device.
This patch reworks FIB rule handling to return a message to the user:
$ ip ru add pref 99 from all to 8.8.8.8 table 11
Error: spectrum: FIB rules not supported. Aborting offload.
spectrum currently only checks whether the fib rule is a default rule or
an l3mdev rule, both of which it knows how to handle. Any other it aborts
FIB offload. Move the processing to check the rule type inline with the
user request. If the rule is an unsupported one, then a work queue entry
is used to abort the offload. Change the rule delete handling to just
return since it does nothing at the moment.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace recurring magic number in PPCNT register with a define.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the HW stats cache to be local. Rename it for better clarity.
It holds the results of the last result of HW stats that are being read
periodically, in order to have answer for stats request immediately.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the spectrum_mr_tcam.c include the spectrum_mr_tcam.h header file.
Cleans up sparse warning:
symbol 'mlxsw_sp_mr_tcam_ops' was not declared. Should it be static?
Fixes: 0e14c7777a ("mlxsw: spectrum: Add the multicast routing hardware logic")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is only used internally in spectrum_mr.c and is not declared
in the header file, thus make it static.
Cleans up sparse warning:
symbol 'mlxsw_sp_mr_dev_vif_lookup' was not declared. Should it be static?
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix various endianness issues in comparisons and assignments. The fix is
entirely cosmetic as all the values fixed are endianness-agnostic.
Cleans up sparse warnings:
spectrum_mr.c:156:49: warning: restricted __be32 degrades to integer
spectrum_mr.c:206:26: warning: restricted __be32 degrades to integer
spectrum_mr.c:212:31: warning: incorrect type in assignment (different
base types)
spectrum_mr.c:212:31: expected restricted __be32 [usertype] addr4
spectrum_mr.c:212:31: got unsigned int
spectrum_mr.c:214:32: warning: incorrect type in assignment (different
base types)
spectrum_mr.c:214:32: expected restricted __be32 [usertype] addr4
spectrum_mr.c:214:32: got unsigned int
spectrum_mr.c:461:16: warning: restricted __be32 degrades to integer
spectrum_mr.c:461:49: warning: restricted __be32 degrades to integer
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the dump the per netlink packet entry counter should be zeroed out
when new packet is created.
Fixes: 190d38a52a ("mlxsw: spectrum_dpipe: Add support for adjacency table dump")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KVD linear is currently partitioned into two partitions. One for
single entries and another for groups of 32 entries.
Add another partition consisting of groups of 512 entries which will
allow us to more accurately represent the nexthop weights in non-equal
cost multi-path routing.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory region where adjacency entries (nexthops) are stored is
called the KVD linear and is configured during initialization with a
size of 64K.
Extend this area with 32K more entries, that will be partitioned into 64
groups of 0.5K entries, thereby allowing us to support weighted nexthops
with high accuracy.
Change the ratio between both types of hash entries, so as to prevent
reduction in the number of double hash entries, which are used for IPv6
neighbours and routes with a prefix length greater than 64.
Note that the user will be able to control all these sizes once the
devlink resource manager is introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the driver assumed all the nexthops have an equal weight
and wrote each to a single adjacency entry.
This patch takes the `weight` parameter into account and populates the
adjacency group according to the relative weight of each nexthop.
Specifically, the weights of all the nexthops that should be offloaded
are first normalized and then used to calculate the upper adjacency
index of each nexthop. This is done according to the hash-threshold
algorithm used by the kernel for IPv4 multi-path routing.
Adjacency groups are currently limited to 32 entries which limits the
weights that can be used, but follow-up patches will introduce groups of
512 entries.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device has certain restrictions regarding the size of an adjacency
group.
Have the router determine the size of the adjacency group according to
available KVDL allocation sizes and these restrictions.
This was not needed until now since only allocations of up 32 entries
were supported and these are all valid sizes for an adjacency group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the first step towards non-equal-cost multi-path support, store each
nexthop's weight.
For IPv6 nexthops always set the weight to 1, as it only supports ECMP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current KVDL allocation API allows the user to specify the requested
number of entries, but the user has no way of knowing how many entries
were actually allocated.
This works because existing users (e.g., router) request the exact
number they end up using. With the introduction of large adjacency
groups, this will change, as the router will have the ability to choose
from several allocation sizes, where larger allocations provide higher
accuracy with respect to requested weights and better resilience against
nexthop failures.
One option is to have the router try several allocations of descending
size until one succeeds, but a better way is to simply allow it to query
the actual allocation size and then size its request accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KVD linear (KVDL) allocator currently consists of a very large
bitmap that reflects the KVDL's usage. The boundaries of each partition
as well as their allocation size are represented using defines.
This representation requires us to patch all the functions that act on a
partition whenever the partitioning scheme is changed. In addition, it
does not enable the dynamic configuration of the KVDL using the
up-coming resource manager.
Add objects to represent these partitions as well as the accompanying
code that acts on them to perform allocations and de-allocations.
In the following patches, this will allow us to easily add another
partition as well as new operations to act on these partitions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adjacency group size is part of the match on the adjacency group and
should therefore be exposed using dpipe.
When non-equal-cost multi-path support will be introduced, the group's
size will help users understand the exact number of adjacency entries
each nexthop occupies, as a nexthop will no longer correspond to a
single entry.
The output for a multi-path route with two nexthops, one with weight 255
and the second 1 will be:
Example:
$ devlink dpipe table dump pci/0000:01:00.0 name mlxsw_adj
pci/0000:01:00.0:
index 0
match_value:
type field_exact header mlxsw_meta field adj_index value 65536
type field_exact header mlxsw_meta field adj_size value 512
type field_exact header mlxsw_meta field adj_hash_index value 0
action_value:
type field_modify header ethernet field destination mac value e4:1d:2d:a5:f3:64
type field_modify header mlxsw_meta field erif_port mapping ifindex mapping_value 3 value 1
index 1
match_value:
type field_exact header mlxsw_meta field adj_index value 65536
type field_exact header mlxsw_meta field adj_size value 512
type field_exact header mlxsw_meta field adj_hash_index value 510
action_value:
type field_modify header ethernet field destination mac value e4:1d:2d:a5:f3:65
type field_modify header mlxsw_meta field erif_port mapping ifindex mapping_value 4 value 2
Thus, the first nexthop occupies 510 adjacency entries and the second 2,
which leads to a ratio of 255 to 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum tunnels do not default to ttl of "inherit" like the Linux ones
do. Configure TIGCR on router init so that the TTL of tunnel packets is
copied from the overlay packets.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are converted to use block callbacks for TC_SETUP_CLS*.
So it is now safe to remove the calls to ndo_setup_tc from cls_*
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced block callback infrastructure and
convert ndo_setup_tc calls for matchall and flower offloads to block
callbacks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of to convert the generic fib_notifier_info into
the event specific data structure.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack argument down to mlxsw_sp_rif_create and mlxsw_sp_vr_create
to set an error message on RIF or VR overflow. Now on overflow of
either resource the user gets an informative message as opposed to
failing with EBUSY.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for inetaddr_validator and inet6addr_validator. The
notifiers provide a means for validating ipv4 and ipv6 addresses
before the addresses are installed and on failure the error
is propagated back to the user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an EMAD is transmitted, a timeout work item is scheduled with a
delay of 200ms, so that another EMAD will be retried until a maximum of
five retries.
In certain situations, it's possible for the function waiting on the
EMAD to be associated with a work item that is queued on the same
workqueue (`mlxsw_core`) as the timeout work item. This results in
flushing a work item on the same workqueue.
According to commit e159489baa ("workqueue: relax lockdep annotation
on flush_work()") the above may lead to a deadlock in case the workqueue
has only one worker active or if the system in under memory pressure and
the rescue worker is in use. The latter explains the very rare and
random nature of the lockdep splats we have been seeing:
[ 52.730240] ============================================
[ 52.736179] WARNING: possible recursive locking detected
[ 52.742119] 4.14.0-rc3jiri+ #4 Not tainted
[ 52.746697] --------------------------------------------
[ 52.752635] kworker/1:3/599 is trying to acquire lock:
[ 52.758378] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c4fa4>] flush_work+0x3a4/0x5e0
[ 52.767837]
but task is already holding lock:
[ 52.774360] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.784495]
other info that might help us debug this:
[ 52.791794] Possible unsafe locking scenario:
[ 52.798413] CPU0
[ 52.801144] ----
[ 52.803875] lock(mlxsw_core_driver_name);
[ 52.808556] lock(mlxsw_core_driver_name);
[ 52.813236]
*** DEADLOCK ***
[ 52.819857] May be due to missing lock nesting notation
[ 52.827450] 3 locks held by kworker/1:3/599:
[ 52.832221] #0: (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.842846] #1: ((&(&bridge->fdb_notify.dw)->work)){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.854537] #2: (rtnl_mutex){+.+.}, at: [<ffffffff822ad8e7>] rtnl_lock+0x17/0x20
[ 52.863021]
stack backtrace:
[ 52.867890] CPU: 1 PID: 599 Comm: kworker/1:3 Not tainted 4.14.0-rc3jiri+ #4
[ 52.875773] Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016
[ 52.886267] Workqueue: mlxsw_core mlxsw_sp_fdb_notify_work [mlxsw_spectrum]
[ 52.894060] Call Trace:
[ 52.909122] __lock_acquire+0xf6f/0x2a10
[ 53.025412] lock_acquire+0x158/0x440
[ 53.047557] flush_work+0x3c4/0x5e0
[ 53.087571] __cancel_work_timer+0x3ca/0x5e0
[ 53.177051] cancel_delayed_work_sync+0x13/0x20
[ 53.182142] mlxsw_reg_trans_bulk_wait+0x12d/0x7a0 [mlxsw_core]
[ 53.194571] mlxsw_core_reg_access+0x586/0x990 [mlxsw_core]
[ 53.225365] mlxsw_reg_query+0x10/0x20 [mlxsw_core]
[ 53.230882] mlxsw_sp_fdb_notify_work+0x2a3/0x9d0 [mlxsw_spectrum]
[ 53.237801] process_one_work+0x8f1/0x12f0
[ 53.321804] worker_thread+0x1fd/0x10c0
[ 53.435158] kthread+0x28e/0x370
[ 53.448703] ret_from_fork+0x2a/0x40
[ 53.453017] mlxsw_spectrum 0000:01:00.0: EMAD retries (2/5) (tid=bf4549b100000774)
[ 53.453119] mlxsw_spectrum 0000:01:00.0: EMAD retries (5/5) (tid=bf4549b100000770)
[ 53.453132] mlxsw_spectrum 0000:01:00.0: EMAD reg access failed (tid=bf4549b100000770,reg_id=200b(sfn),type=query,status=0(operation performed))
[ 53.453143] mlxsw_spectrum 0000:01:00.0: Failed to get FDB notifications
Fix this by creating another workqueue for EMAD timeouts, thereby
preventing the situation of a work item trying to flush a work item
queued on the same workqueue.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Formerly, IPIP entries were created lazily by next hops that referenced
an offloadable IP-in-IP netdevice. However now that they are created
eagerly as a reaction to events on such netdevices, the reference
counting is useless. Hence drop it.
The routes whose next hops reference an offloaded IP-in-IP netdevice
actually linger around a bit after their device is unregistered.
However, mlxsw_sp_ipip_entry_destroy() also destroys the backing
loopback, and mlxsw_sp_rif_destroy() transitively (via
mlxsw_sp_nexthop_rif_gone_sync()) calls mlxsw_sp_nexthop_ipip_fini(),
which unlinks the IPIP entry from a next hop. Thus no dangling pointers
are left behind for the brief window after netdevice is gone, but routes
not yet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPIP entries are created as soon as an offloadable device is created.
That means that when such a device is later moved to a different VRF,
the loopback device that backs the tunnel is wrong.
Thus when an offloadable encapsulating netdevice moves from one VRF to
another, make sure that the loopback is updated as necessary.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.
To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.
Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER port attribute switchdev
notification.
To do that, add the mrouter flag to struct mlxsw_sp_bridge_device, which
indicates whether the bridge device was set to be mrouter port. This field
is set when:
- A new bridge is created, where the value is taken from the kernel
bridge value.
- A switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent.
In addition, change the bridge MID entries to include the router port when
the bridge device is configured to be mrouter port. The MID entries are
updated in the following cases:
- When a new MID entry is created, update the router port according to the
bridge mrouter state.
- When a SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent, update all
the bridge's MID entries.
This is aligned with the case where a bridge slave is configured to be
mrouter port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum, MDB entries point to MID entries, that indicate which ports a
packet should be forwarded to. Add the support in creating MID entries that
forward the packet to the Spectrum router port.
This will be later used to handle the bridge mrouter port switchdev
notifications.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum hardware, the router port is a virtual port that is the gateway
to the routing mechanism. Hence, in order for a packet to be L3 forwarded,
it must first be L2 forwarded to the router port inside the hardware.
Further patches in this patchset are going to introduce support in bridge
device used as an mrouter port. In this case, the router port index will be
needed in order to update the MDB entries to include the router port. Thus,
export the mlxsw_sp_router_port function, which returns the index of the
Spectrum router port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that actually takes care of bridge offload introduces a few
more non-trivial constraints with regards to bridge enslavements.
Propagate extack there to indicate the reason.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add link enp1s0np1 name enp1s0np1.20 type vlan id 20
$ ip link add name br0 type bridge
$ ip link set dev enp1s0np1.10 master br0
$ ip link set dev enp1s0np1.20 master br0
Error: spectrum: Can not bridge VLAN uppers of the same port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to physical ports, enslavement of VLAN devices can also fail.
Use extack to indicate why the enslavement failed.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add name bond0 type bond mode 802.3ad
$ ip link set dev enp1s0np1.10 master bond0
Error: spectrum: VLAN devices only support bridge and VRF uppers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I increased the scale of supported VRFs by having
all of them share the same LPM tree.
In order to avoid look-ups for prefix lengths that don't exist, each
route removal would trigger an aggregation across all the active virtual
routers to see which prefix lengths are in use and which aren't and
structure the tree accordingly.
With the way the data structures are currently laid out, this is a very
expensive operation. When preformed repeatedly - due to the invocation
of the abort mechanism - and with enough VRFs, this can result in a hung
task.
For now, avoid this optimization until it can be properly re-added in
net-next.
Fixes: fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw fails device enslavement for a number of reasons. Use the extack
facility to return an error message to the user stating why the enslave
is failing.
Messages are prefixed with "spectrum" so users know it is a constraint
imposed by the hardware driver. For example:
$ ip li add br0.11 link br0 type vlan id 11
$ ip li set swp11 master br0
Error: spectrum: Enslaving a port to a device that already has an upper device is not supported.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success if the kmalloc_array() call fails.
Fixes: 0e14c7777a ("mlxsw: spectrum: Add the multicast routing hardware logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw_afa_block_create() doesn't return error pointers, it returns NULL
on error.
Fixes: 0e14c7777a ("mlxsw: spectrum: Add the multicast routing hardware logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support of trap-and-forward route action in the multicast routing
offloading logic. A route will be set to trap-and-forward action if one (or
more) of its output interfaces is not offload-able, i.e. does not have a
valid Spectrum RIF.
This way, a route with mixed output VIFs list, which contains both
offload-able and un-offload-able devices can go through partial offloading
in hardware, and the rest will be done in the kernel ipmr module.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the current multicast route actions, which include trap
route action and a forward route action, add the trap-and-forward multicast
route action, and implement it in the multicast routing hardware logic.
To implement that, add a trap-and-forward ACL action as the last action in
the route flexible action set. The used trap is the ACL2 trap, which marks
the packets with offload_mr_forward_mark, to prevent the packet from being
forwarded again by the kernel.
Note: At that stage the offloading logic does not support trap-and-forward
multicast routes. This patch adds the support only in the hardware logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a multicast route is configured with trap-and-forward action, the
packets should be marked with skb->offload_mr_fwd_mark, in order to prevent
the packets from being forwarded again by the kernel ipmr module.
Due to this, it is not possible to use the already existing multicast trap
(MLXSW_TRAP_ID_ACL1) as the packet should be marked differently. Add the
MLXSW_TRAP_ID_ACL2 which is for trap-and-forward multicast routes, and set
the offload_mr_fwd_mark skb field in its handler.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use trap/discard flex action to implement trap and forward. The action will
later be used for multicast routing, as the multicast routing mechanism is
done using ACL flexible actions in Spectrum hardware. Using that action, it
will be possible to implement a trap-and-forward route.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When considering whether to set RTNH_F_OFFLOAD flag on an IPv6 route,
mlxsw_sp_fib6_entry_offload_set() looks up the mlxsw_sp_nexthop
corresponding to a given route, and decides based on whether the next
hop's offloaded flag was set. When looking for the matching next hop, it
also takes into account the device of the route, which must match next
hop's RIF.
IPIP next hops however hitherto didn't set the RIF. As a result, IPv6
routes forwarding traffic to IP-in-IP netdevices are never marked as
offloaded, even when they actually are.
Thus track RIF of IPIP next hops the same way as that of ETHERNET next
hops.
Fixes: 8f28a30976 ("mlxsw: spectrum_router: Support IPv6 overlay encap")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a new RIF, bumping RIF count of the containing VR is the
last thing to be done. Symmetrically, when destroying a RIF, RIF count
is first dropped and only then the rest of the cleanup proceeds.
That's a problem for loopback RIFs. Those hold two VR references: one
for overlay and one for underlay. mlxsw_sp_rif_destroy() releases the
overlay one, and the deconfigure() callback the underlay one. But if
both overlay and underlay are the same, and if there are no other
artifacts holding the VR alive, this put actually destroys the VR. Later
on, when mlxsw_sp_rif_destroy() calls mlxsw_sp_vr_put() for the same VR,
the VR will already have been released and the kernel crashes with NULL
pointer dereference.
The underlying problem is that the RIF under destruction ends up
referencing the overlay VR much longer than it claims: all the way until
the call to mlxsw_sp_vr_put(). So line up the reference counting
properly to reflect this. Make corresponding changes in
mlxsw_sp_rif_create() as well for symmetry.
Fixes: 6ddb7426a7 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event that mfc->mfc_un.res.ttls[i] is 255 for all
values of i from 0 to MAXIVS-1, the err is not set at all and hence
has a garbage value on the error return at the end of the function,
so initialize it to 0. Also, the error return check on err and goto
to err: inside the for loop makes it impossible for err to be zero
at the end of the for loop, so we can remove the redundant err check
at the end of the loop.
Detected by CoverityScan CID#1457207 ("Unitialized scalar value")
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Spectrum router logic not ignore the RTNL_FAMILY_IPMR FIB
notifications.
Past commits added the IPMR VIF and MFC add/del notifications via the
fib_notifier chain. In addition, a code for handling these notifications in
the Spectrum router logic was added. Make the Spectrum router logic not
ignore these notifications and forward the requests to the Spectrum
multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that multicast routes hold the minimum MTU of all the
egress RIFs and trap packets that don't meet it, notify the mulitcast
router code on RIF MTU changes.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality for calling the multicast routing offloading logic upon
MFC and VIF add and delete notifications. In addition, call the multicast
routing upon RIF addition and deletion events.
As the multicast routing offload logic may sleep, the actual calls are done
in a deferred work. To ensure the MFC object is not freed in that interval,
a reference is held to it. In case of a failure, the abort mechanism is
used, which ejects all the routes from the hardware and triggers the
traffic to flow through the kernel.
Note: At that stage, the FIB notifications are still ignored, and will be
enabled in a further patch.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mlxsw Spectrum driver offloads only either the RT_TABLE_MAIN
FIB table or the VRF tables, so the RT_TABLE_LOCAL table is squashed to the
RT_TABLE_MAIN table to allow local routes to be offloaded too.
By default, multicast MFC routes which are not assigned to any user
requested table are put in the RT_TABLE_DEFAULT table.
Due to the fact that offloading multicast MFC routes support in Spectrum
router logic is going to be introduced soon, squash the default table to
MAIN too.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the multicast routing hardware API introduced in previous patch
for the specific spectrum hardware.
The spectrum hardware multicast routes are written using the RMFT2 register
and point to an ACL flexible action set. The actions used for multicast
routes are:
- Counter action, which allows counting bytes and packets on multicast
routes.
- Multicast route action, which provide RPF check and do the actual packet
duplication to a list of RIFs.
- Trap action, in the case the route action specified by the called is
trap.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the multicast router offloading logic, which is in charge of handling
the VIF and MFC notifications and translating it to the hardware logic API.
The offloading logic has to overcome several obstacles in order to safely
comply with the kernel multicast router user API:
- It must keep track of the mapping between VIFs to netdevices. The user
can add an MFC cache entry pointing to a VIF, delete the VIF and add
re-add it with a different netdevice. The offloading logic has to handle
this in order to be compatible with the kernel logic.
- It must keep track of the mapping between netdevices to spectrum RIFs,
as the current hardware implementation assume having a RIF for every
port in a multicast router.
- It must handle routes pointing to pimreg device to be trapped to the
kernel, as the packet should be delivered to userspace.
- It must handle routes pointing tunnel VIFs. The current implementation
does not support multicast forwarding to tunnels, thus routes that point
to a tunnel should be trapped to the kernel.
- It must be aware of proxy multicast routes, which include both (*,*)
routes and duplicate routes. Currently proxy routes are not offloaded
and trigger the abort mechanism: removal of all routes from hardware and
triggering the traffic to go through the kernel.
The multicast routing offloading logic also updates the counters of the
offloaded MFC routes in a periodic work.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate error instead of doing WARN_ON right away.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling nexthop counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adjacency table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on nexthops based on dpipe's adjacency
table counter status. This patch also adds the ability for getting the
counter value, which will be used by the dpipe adjacency table dump
implementation in the next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to add the ability for setting counters on nexthops the RATR
register should be extended.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial support for router adjacency table. The table does lookup
based on the nexthop-group index and the local nexthop offset. After
locating the nexthop entry it sets the destination MAC address and the
egress RIF.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing the ability to dump the
adjacency table via dpipe, and to count the table size. The current table
implementation avoids tunnel entries, thus a helper for checking if
the nexthop group contains tunnel entries is also provided. The mlxsw's
nexthop representative struct stays private to the router module.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_is_last helper to check for last neighbor.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep nexthops in a linked list for easy access.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds field for mlxsw's meta header which will be used to
describe the match/action behavior of the adjacency table.
The fields are:
1. Adj_index - The global index of the nexthop group in the adjacency
table.
2. Adj_hash_index - Local index offset which is based on packets hash
mod the nexthop group size.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix indentation in mlxsw_meta header's description.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a mrouter is registered or leaves a mid, don't update the HW.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mdb flush the port is being removed from all the mids it is registered
to. But if the port is mrouter, all the mids floods to it.
This patch remove mrouter ports from mids it is not registered to in the
mdb flush.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a port starts / stops being mrouter, update all the mdb entries
in the HW to flood / stop flooding mc packets there.
The change should happen only if the port is not in the mid. (If it is,
the mid should flood mc packets to this port anyway)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mc is enabled, whenever a mc packet doesn't hit any mdb entry it is
being flood to the ports marked as mrouters. However, all mc packets should
be flooded to them even if they match an entry in the mdb.
This patch adds the mrouter ports to every mdb entry that is being written
to the HW.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is being removed from a bridge, flush the bridge mdb to remove
the mids of that port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multicast is disabled, flood mc packets only to port that are marked
BR_MCAST_FLOOD (instead to all).
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic mc flood function to decide whether to flood mc to a port
when mc is being enabled / disabled.
Move this function in the file to avoid forward declaration.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all the mdb entries from the HW when mc is being disabled and
re-write them when it is being enabled.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't write multicast related data to the HW when mc is disabled.
Also, don't allocate mid id to new mids (so the remove function could know
that they weren't wrote to the HW)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break mid deletion into two function, so it will be possible in the future
to delete a mid entry for other reasons then switchdev command (like port
deletion).
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attach mid getting and releasing mid id to the HW write / remove, and add
a flag to indicate whether the mid is in the HW. It is done because mid id
is also HW index to this mid.
This change allows adding in the following patches the ability to have a
mid in the mdb cache but not in the HW. It will be useful for being able
to disable the multicast.
It means that the mdb is being written / delete to the HW in the mid
allocation / removing function, not after them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the smid write function into two, one that cleans the ports that
might be still written there and one that changes an exiting mid entry.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of saving all the mids in the same list, save them per vlan
device. This change allows a more efficient mid find.
Also, in the next patches, there will be added a lot of loops over all the
mids in bridge device for multicast disable, mrouter change and ndb flush.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is a bitmap for the ports registered to each mid, there is no
need for a ref count, since it will always be the number of set bits in
this bitmap. Any check of the ref count was replaced with checking if the
bitmap is empty.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bitmap of ports to the mid struct to hold the ports that are
registered to this mid.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the naming of mc_router to mrouter to keep consistency.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three new traps needed for multicast routing:
- PIM: Trap for PIM protocol control packets.
- RPF: Trap for packets that fail the RPF check on a specific hardware
route entry.
- MULTICAST: Generic trap for multicast. It is used for routes that trap
the packets to the CPU.
The RPF and MULTICAST traps have rate limiters as these traps may have
line-rate of packets trapped. The PIM trap has a rate limiter similarly to
other L3 control protocols. The rate limiters are implemented by adding
three new trap groups for the newly introduced traps.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw_sp_rif struct, defined as private struct in spectrum_router.c
will be used in the multicast router source file. Due to the fact that the
dev field will be needed by the multicast router logic, add an access
function to it.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn on two bits on the Spectrum RIF configuration:
- IPv4 multicast: when a multicast packet arrives on a RIF, send it to go
through multicast routes lookup.
- IPv4 multicast forwarding enable: when multicast packet arrives on a
RIF, allow it to be forwarded by multicast routes. If this bit is not
set, multicast packets will go through multicast routing lookup but will
be dropped at the egress of the ports.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RRCR register is used for copying and moving TCAM multicast routes
from different offsets. It will be used to allow routes relocation for
parman ops as part of the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RMFT-V2 register is used to configure and query the multicast table and
will be used by the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast ERIF list entries resource indicates the number of entries
that can be put in one rigr2 register operation. While the register can
hold up to MLXSW_REG_RIGR2_MAX_ERIFS ( = 32) ERIF entries, the actual
number allowed by firmware is indicated with this resource.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RIGR-V2 register is used to add, remove and query egress interface list
of a multicast forwarding entry and it will be used by the multicast
router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for allocation of regions in the TCAM table and it
will be used by the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MLXSW_REG_PXXX_FLEX_ACTION_SET_LEN is relevant for the multicast router
registers too, so rename it to have a general name which is not bound to a
specific register.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the trap ACL action to be configured with different traps. This
allows the multicast router offloading code to use that same ACL action
with the multicast router traps. By using different traps, the multicast
router can have different trap policies and can handle the packet
differently.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum multicast forwarding is done using an ACL action. Add the
mcrouter ACL action that will be used to offload the multicast router
logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A flexible action instance allows, given a set of ops, creating, committing
and sharing a set of ACL action blocks. The flexible action instance in
question is using the spectrum KVD linear space to store the flexible
action sets.
Move this flexible action instance to the common spectrum struct to allow
other users (such as multicast router) to get that functionality.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast router offloading code is going to require the counter_pools
initialization to occur before the router initialization, thus, change the
spectrum initialization order to fix it.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.
This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.
Fixes: 65e65ec137 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Andreas Rammhold <andreas@rammhold.de>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the offloading of mirred actions under
matchall classifiers, mlxsw would find the destination port
associated with the offloaded action and utilize it for undoing
the configuration.
Depending on the order by which ports are removed, it's possible that
the destination port would get removed before the source port.
In such a scenario, when actions would be flushed for the source port
mlxsw would perform an illegal dereference as the destination port is
no longer listed.
Since the only item necessary for undoing the configuration on the
destination side is the port-id and that in turn is already maintained
by mlxsw on the source-port, simply stop trying to access the
destination port and use the port-id directly instead.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not handle correctly the access to the upper page
in case of SFP/SFP+ EEPROM. In that case the offset should be local
and the I2C address should be changed.
Fixes: 2ea109039c ("mlxsw: spectrum: Add support for access cable info via ethtool")
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces callbacks and tunnel type to offload GRE tunnels.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct mlxsw_sp_rif is a router-private structure, and therefore
everything related to it is as well: parameters, and derived RIF types
including loopbacks. IPIP module needs access to some details of
loopback interfaces, but exporting all the RIF shebang would create too
large an interface.
So instead export just the bare minimum necessary: accessors for RIF
index and underlay VRF ID.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These traps are generated for packets that fail checks for source IP,
encapsulation type, or GRE key. Trap these packets to CPU for follow-up
handling by the kernel, which will send ICMP destination unreachable
responses.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local route that points at IPIP's underlay device (decap route) can
be present long before the GRE device. Thus when an encap route is
added, it's necessary to look inside the underlay FIB if the decap route
is already present. If so, the current trap offload needs to be
withdrawn and replaced with a decap offload.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike encapsulation, which is represented by a next hop forwarding to
an IPIP tunnel, decapsulation is a type of local route. It is created
for local routes whose prefix corresponds to the local address of one of
offloaded IPIP tunnels. When the tunnel is removed (i.e. all the encap
next hops are removed), the decap offload is migrated back to a trap for
resolution in slow path.
This patch assumes that decap route is already present when encap route
is added. A follow-up patch will fix this issue.
Note that this patch only supports IPv4 underlay. Support for IPv6
underlay will be subject to follow-up work apart from this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing bits to recognize IPv6 next hops as IPIP ones to enable
offloading of IPv6 overlay encapsulation.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces some common code for tracking of offloaded IP-in-IP
tunnels, and support for offloading IPv4 overlay encapsulating routes in
particular. A follow-up patch will introduce IPv6 overlay as well.
Offloaded tunnels are kept in a linked list of mlxsw_sp_ipip_entry
objects hooked up in mlxsw_sp_router. A network device that represents
the tunnel is used as a key to look up the corresponding IPIP entry.
Note that in the future, more general keying mechanism will be needed,
because parts of the tunnel information can be provided by the route.
IPIP entries are reference counted, because several next hops may end up
using the same tunnel, and we only want to offload it once.
Encapsulation path hooks into next hop handling. Routes that forward to
a tunnel are now considered gateway routes, thus giving them the same
treatment that other remote routes get. An IPIP next hop type is
introduced.
Details of individual tunnel types are kept in an array of
mlxsw_sp_ipip_ops objects. If a tunnel type doesn't match any of the
known tunnel types, the next-hop is not considered an IPIP next hop.
The list of IPIP tunnel types is currently empty, follow-up patches will
add support for GRE. Traffic to IPIP tunnel types that are not
explicitly recognized by the driver traps and is handled in slow path.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the router, some next hops may reference an encapsulating netdevice,
such as GRE or IPIP. To properly offload these next hops, mlxsw needs to
keep track of whether a given next hop is a regular Ethernet entry, or
an IP-in-IP tunneling entry.
To facilitate this book-keeping, add a type field to struct
mlxsw_sp_nexthop. There is, as of this patch, only one next hop type:
MLXSW_SP_NEXTHOP_TYPE_ETH. Follow-up patches will introduce the IP-in-IP
variant.
There are several places where next hops are initialized in the IPv4
path. Instead of replicating the logic at every one of them, factor it
out to a function mlxsw_sp_nexthop4_type_init(). The corresponding fini
is actually protocol-neutral, so put it to mlxsw_sp_nexthop_type_fini(),
but create a corresponding protocoled _fini function that dispatches to
the protocol-neutral one.
The IPv6 path is simpler, but for symmetry with IPv4, create the same
suite of functions with corresponding logic.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 counterpart of the previous patch: introduce a function to
determine whether a given route is a gateway route.
The new function takes a mlxsw_sp argument which follow-up patches will
use. Thus mlxsw_sp_fib6_entry_type_set() got that argument as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IPv4 IP-in-IP offload, routes that direct traffic to IP-in-IP
devices need to be considered gateway routes as well. That involves a
bit more logic, so extract the current test to a separate function,
where the logic can be later added.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading L3 tunnels, an adjacency entry is created that loops the
packet back into the underlay router. Loopback interfaces then hold the
corresponding information and are created for IP-in-IP netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback RIFs, which will be introduced in a follow-up patch, differ
from other RIFs in that they do not have a FID associated with them.
To support this, demote FID allocation from mlxsw_sp_rif_create to
configure op of the existing RIF types, and likewise the FID release
from mlxsw_sp_rif_destroy to deconfigure op.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Details of individual tunnel types are kept in an array of
mlxsw_sp_ipip_ops objects. Follow-up patches will use the list to
determine whether a constructed RIF should be a loopback, and to decide
whether a next hop references a tunnel.
The list is currently empty, follow-up patches will add support for GRE.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spectrum_ipip module that will be introduced in the follow-up
patches needs to know the data type.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support IPIP, the driver needs to be able to construct an IPIP
adjacency. Change mlxsw_reg_ratr_pack to take an adjacency type as an
argument. Adjust the one existing caller.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other interface types, loopback RIFs do not have MAC address. So
drop the corresponding argument from mlxsw_reg_ritr_pack() and move it
to a new function. Call that from callers of mlxsw_reg_ritr_pack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTDP register is used for configuring the tunnel decap properties of
NVE and IPinIP.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To implement IP-in-IP decapsulation, Spectrum uses LPM entries of type
IP2ME with tunnel validity bit and tunnel pointer set. The necessary
register fields are already available, so add a function to pack the
RALUE as appropriate.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enum is used with reg_ratr_trap_id, so move it next to the register
definition.
While at it, drop the enumerator initializers.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, adjacencies have always been of type Ethernet (with value of 0),
and thus there was no need to explicitly support RATR type. However to
support IP-in-IP adjacencies, this type and a suite of IP-in-IP-specific
attributes need to be added.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the register so that loopback RIFs can be created and loopback
properties specified.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the abort mechanism is invoked a default route directing packets to
the CPU is programmed in all the virtual routers currently in use. This
can result in packet loss in case a new VRF is configured.
Upon abort, program the default route in all virtual routers, whether
they are in use or not.
The patch is directed at net-next since post-abort fixes aren't critical
and packet loss due to a missing default route will be insignificant
compared to packet loss caused by the CPU port policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I relied on the fact that anycast routes use the loopback device as
their nexthop device to trap packets hitting them to the CPU.
After commit 4832c30d54 ("net: ipv6: put host and anycast routes on
device with address") this is no longer the case and such routes are
programmed with a forward action (note the 'offload' flag):
anycast cafe:: dev enp3s0np7 proto kernel metric 0 offload pref medium
This will prevent the router from locally receiving packets destined to
the Subnet-Router anycast address.
Fix this by specifically programming anycast routes with action trap,
which results in the following output:
anycast cafe:: dev enp3s0np7 proto kernel metric 0 pref medium
Fixes: 4832c30d54 ("net: ipv6: put host and anycast routes on device with address")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling IPv6 neighbor counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on IPv6 neighbors based on dpipe's host6
table counter status.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 host table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the host entry filler helper to be applicable for both IPv4/6
addresses.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper for accessing destination IP in case of IPv6 neighbor.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 host table initial support. The action behavior for both IPv4/6
tables is the same, thus the same action dump op is used. Neighbors with
link local address are ignored.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neighbors with link local addresses are not offloaded to the host table,
yet, the are maintained in the driver for adjacency table usage. When
dumping the IPv6 host neighbors this link local neighbors should be
ignored. This patch exports this helper for dpipe usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the neighbor traversal the neighbors from different families
should be ignored.
Fixes: c58035a74aba ("mlxsw: spectrum_dpipe: Add support for IPv4 host table dump")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes no sense to have dpipe compiled in when devlink is not enabled,
because the devlink dpipe registation is noop function. So don't compile
it in. This also fixes missing extern structs errors.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: a86f030915 ("mlxsw: spectrum_dpipe: Add support for IPv4 host table dump")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling neighbor counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv4 host table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on neighbors based on dpipe's host table
counter status. This patch also adds the ability for getting the counter
value, which will be used by the dpipe host table implementation in the
next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing support for neighbor
counters. The flow counter's type enum is used by many registers, yet,
until now it was used only by mgpc and thus it was private. This patch
updates the namespace for more generic usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change label name for case of erif table init failure.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing the ability to dump the
host table via dpipe, and to count the table size. The mlxsw's neighbor
representative struct stays private to the router module.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry clear routine can be shared between the drivers, thus it is
moved inside devlink.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the dpipe table's size was static and known at registration
time. The host table does not have constant size and it is resized in
dynamic manner. In order to support this behavior the size is changed
to be obtained dynamically via an op.
This patch also adjust the current dpipe table for the new API.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ERIF's table operations name space.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If action is gact goto_chain, offload it to HW by jumping to another
ruleset.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to lookup ruleset in order to offload goto_chain termination
action. This patch adds it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For goto_chain action we need to know group_id of a ruleset to jump to.
Provide infrastructure in order to get it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflect chain index coming down from TC core and create a ruleset per
chain. Note that only chain 0, being the implicit chain, is bound to the
device for processing. The rest of chains have to be "jumped-to" by
actions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the value of the mrouter flag in struct mlxsw_sp_bridge_port when
it is being changed.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made an embarrassing mistake and used 'IPV6' instead of 'CONFIG_IPV6'
around the function that updates the kernel about IPv6 neighbours
activity. This can be a problem if the kernel has more neighbours than a
certain threshold and it starts deleting those that are supposedly
inactive.
Fixes: b5f3e0d430 ("mlxsw: spectrum_router: Fix build when IPv6 isn't enabled")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 routes currently lack nexthop flags as in IPv4. This has several
implications.
In the forwarding path, it requires us to check the carrier state of the
nexthop device and potentially ignore a linkdown route, instead of
checking for RTNH_F_LINKDOWN.
It also requires capable drivers to use the user facing IPv6-specific
route flags to provide offload indication, instead of using the nexthop
flags as in IPv4.
Add nexthop flags to IPv6 routes in the 40 bytes hole and use it to
provide offload indication instead of the RTF_OFFLOAD flag, which is
removed while it's still not part of any official kernel release.
In the near future we would like to use the field for the
RTNH_F_{LINKDOWN,DEAD} flags, but this change is more involved and might
not be ready in time for the current cycle.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to limited ASIC resources the maximum number of routes is limited by
the nexthop resource. In order to improve the routing scale nexthop
consolidation should be performed.
This patch adds support for IPv6 neighbor consolidation. The hash value
is calculated based on the nexthop set, by performing bitwise xor on the
ifindexs of the nexthops, in a similar way to IPv4's kernel implementation.
In case of collision a full match is performed between the sets which
include address and ifindex comparison.
Non gateway nexthop groups are not inserted to the hash table due to
lack of nexthop device (ifindex).
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does preparation before introducing IPv6 nexthop group
consolidation. Currently the nexthop group hash table is used only by
IPv4 and uses fixed key size. In order to support the IPv6's variable
length key the current table is changed.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of LPM trees available for lookup is much smaller than the
number of virtual routers, which are used to implement VRFs. In
addition, an LPM tree can only be used by one protocol - either IPv4 or
IPv6.
Therefore, in order to increase the number of supported virtual routers
to the maximum we need to be able to share LPM trees across virtual
routers instead of trying to find an optimized tree for each.
Do that by allocating one LPM tree for each protocol, but make sure it
will only include prefixes that are actually used, so as to not perform
unnecessary lookups.
Since changing the structure of a bound tree isn't recommended, whenever
a new tree it required, it's first created and then bound to each
virtual router, replacing the old one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on the LPM tree to be assigned to the virtual router
before binding the two, lets pass it explicitly.
This will later allow us to return upon binding error instead of having
to perform a rollback of the assignment.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in returning a value from function whose return value
is never checked.
Even if the return value was checked, there wouldn't be anything to do
about it, as these functions are either called from error or deletion
paths.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these structures const as they only stored in the profile field of
a mlxsw_driver structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking handle, which does not have the inner class
information and drivers wrongly assume clsact->egress as ingress, use
the newly introduced classid identification helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prio is not cls_flower specific, but it is meaningful for all
classifiers. Seems that only mlxsw cares about the value. Obviously,
cls offload in other drivers is broken.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To sync-up with the naming in the rest of the driver, rename the cls arg.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlxsw_sp_setup_tc be a splitter for specific setup_tc types and push
out cls_flower and cls_matchall specific codes into separate functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be aligned with the rest of the types, rename
TC_SETUP_MATCHALL to TC_SETUP_CLSMATCHALL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.
Since the initial introduction of IGMP snooping in commit 3a49b4fde2
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.
The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.
For now, upon module removal, traverse the MID list and release each
one.
Fixes: 3a49b4fde2 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.
Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.
Remove the warnings in such situations and return normally.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d96 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have all the necessary IPv6 infrastructure in place, so stop
ignoring these notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without resorting to ACLs, the device performs route lookup solely based
on the destination IP address.
In case source-specific routing is needed, an error is returned and the
abort mechanism is activated, thus allowing the kernel to take over
forwarding decisions.
Instead of aborting, we can trap specific destination prefixes where
source-specific routes are present, but this will result in a lot more
code that is unlikely to ever be used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we got a replace event, then the replaced route must exist. If
the route isn't capable of multipath, then replace first matching
non-multipath capable route.
If the route is capable of multipath and matching multipath capable
route is found, then replace it. Otherwise, replace first matching
non-multipath capable route.
The new route is inserted before the replaced one. In case the replaced
route is currently offloaded, then it's overwritten in the device's table
by the new route and later deleted, thus not impacting routed traffic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow directly connected and remote unicast IPv6 routes to be programmed
to the device's tables.
As with IPv4, identical routes - sharing the same destination prefix -
are ordered in a FIB node according to their table ID and then the
metric. While the kernel doesn't share the same trie for the local and
main table, this does happen in the device, so ordering according to
table ID is needed.
Since individual nexthops can be added and deleted in IPv6, each FIB
entry stores a linked list of the rt6_info structs it represents. Upon
the addition or deletion of a nexthop, a new nexthop group is allocated
according to the new configuration and the old one is destroyed.
Identical groups aren't currently consolidated, but will be in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only allow FIB offload in the presence of default rules or an l3mdev
rule. In a similar fashion to IPv4 FIB rules, sanitize IPv6 rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification block currently only handles IPv4 events, but we
want to start handling IPv6 events soon, so lay the groundwork now.
Do that by preparing the work item and process it according to the
notified address family.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to add IPv6 notifications in the FIB notification chain, but
the driver currently doesn't support these, so ignore them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification chain is currently soley used by IPv4 code.
However, we're going to introduce IPv6 FIB offload support, which
requires these notification as well.
As explained in commit c3852ef7f2 ("ipv4: fib: Replay events when
registering FIB notifier"), upon registration to the chain, the callee
receives a full dump of the FIB tables and rules by traversing all the
net namespaces. The integrity of the dump is ensured by a per-namespace
sequence counter that is incremented whenever a change to the tables or
rules occurs.
In order to allow more address families to use the chain, each family is
expected to register its fib_notifier_ops in its pernet init. These
operations allow the common code to read the family's sequence counter
as well as dump its tables and rules in the given net namespace.
Additionally, a 'family' parameter is added to sent notifications, so
that listeners could distinguish between the different families.
Implement the common code that allows listeners to register to the chain
and for address families to register their fib_notifier_ops. Subsequent
patches will implement these operations in IPv6.
In the future, ipmr and ip6mr will be extended to provide these
notifications as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we provide offload indication using the nexthop's flags we must
refresh the offload indication whenever the offload state within the
group changes.
This didn't matter until now, as offload indication was provided using
the FIB info flags and multipath routes were marked as offloaded as long
as one of the nexthops was offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch removed the reliance on the counter in the FIB info to
set the offload indication, so we no longer need to keep an offload
state on each FIB entry and can just set or unset the RTNH_F_OFFLOAD
flag in each nexthop.
This is also necessary because we're going to need to refresh the
offload indication whenever the nexthop group associated with the FIB
entry is refreshed. Current check would prevent us from marking a newly
resolved nexthop as offloaded if the FIB entry is already marked as
offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patch, use the nexthop flags to provide
offload indication instead of the FIB info's flags.
In case a nexthop in a multipath route can't be offloaded (gateway's MAC
can't be resolved, for example), then its offload flag isn't set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'trans->tid' is only assigned later in the function, resulting in a zero
transaction ID. Use 'tid' instead.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
Express the same logic more succinctly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer logical operator that expresses the intent to bitwise one that
happens to give the same result.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames IP2ME-specific registers reg_ralue_v and
reg_ralue_tunnel_ptr to reg_ralue_ip2me_*.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments really belong to the individual enumerators. The comment
at the register should instead reference the enum.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
