The default of 0 is 500us of link training, but that's not enough for
some platforms. Decoding this correctly means we're using 2.5ms of
link training on these platforms, which fixes flickering issues
associated with enabling PSR.
v2: Unbotch the math a bit.
v3: Drop debug hunk.
v4: Improve commit message.
Tested-by: Lyude <cpaul@redhat.com>
Cc: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: fritsch@kodi.tv
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-2-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit 50db139018)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In BXT DSI there is no regs programmed with few horizontal timings
in Pixels but txbyteclkhs.. So retrieval process adds some
ROUND_UP ERRORS in the process of PIXELS<==>txbyteclkhs.
Actually here for the given adjusted_mode, we are calculating the
value programmed to the port and then back to the horizontal timing
param in pixels. This is the expected value at the end of get_config,
including roundup errors. And if that is same as retrieved value
from port, then retrieved (HW state) adjusted_mode's horizontal
timings are corrected to match with SW state to nullify the errors.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461053894-5058-2-git-send-email-ramalingam.c@intel.com
(cherry picked from commit 042ab0c3c4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With the introduction of a distinct engine->id vs the hardware id, we need
to fix up the value we use for selecting the target engine when signaling
a semaphore. Note that these values can be merged with engine->guc_id.
Fixes: de1add3605
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461932305-14637-3-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 215a7e3210)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Set the lane count for HDMI to 4. This will make it easier to
unduplicate CHV phy code.
This also fixes the the soft reset programming for HDMI with CHV. After
commit a8f327fb84 ("drm/i915: Clean up CHV lane soft reset
programming"), it wouldn't set the right bits for PCS23 since it relied
on a lane count that was never set.
v2: Set lane_count in *_get_config() to please state checker. (0day)
v3: Set lane_count for DDI in DVI mode too. (CI)
v4: Add note about CHV soft lane reset. (Ander)
Fixes: a8f327fb84 ("drm/i915: Clean up CHV lane soft reset programming")
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-2-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit d4d6279abe)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Faced with sporadic machine hangs on gen7, that mimic the issue of
concurrent writes to the same cacheline and seem to start with
commit 9b9ed30936 (drm/i915: Remove forcewake dance from seqno/irq
barrier on legacy gen6+), let us restore the spinlock around the mmio
read.
Fixes: 9b9ed30936 (drm/i915: Remove forcewake dance from seqno/irq...)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461744121-27051-1-git-send-email-chris@chris-wilson.co.uk
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit bcbdb6d011)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Move the intel_enable_gtt() call to happen before we touch the GTT
during resume. Right now it's done way too late. Before
commit ebb7c78d35 ("agp/intel-gtt: Only register fake agp driver for gen1")
it was actually done earlier on account of also getting called from
the resume hook of the fake agp driver. With the fake agp driver
no longer getting registered we must move the call up.
The symptoms I've seen on my 830 machine include lowmem corruption,
other kinds of memory corruption, and straight up hung machine during
or just after resume. Not really sure what causes the memory corruption,
but so far I've not seen any with this fix.
I think we shouldn't really need to call this during init, but we have
been doing that so I've decided to keep the call. However moving that
call earlier could be prudent as well. Doing it right after the
intel-gtt probe seems appropriate.
Also tested this on 946gz,elk,ilk and all seemed quite happy with
this change.
v2: Reorder init_hw vs. enable_hw functions (Chris)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: ebb7c78d35 ("agp/intel-gtt: Only register fake agp driver for gen1")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462559755-353-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit ac840ae535)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
DP dual mode type 1 DVI adaptors aren't required to implement any
registers, so it's a bit hard to detect them. The best way would
be to check the state of the CONFIG1 pin, but we have no way to
do that. So as a last resort, check the VBT to see if the HDMI
port is in fact a dual mode capable DP port.
v2: Deal with VBT code reorganization
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Reduce DEVICE_TYPE_DP_DUAL_MODE_BITS a bit
Accept both DP and HDMI dvo_port in VBT as my BSW
at least declare its DP port as HDMI :(
v3: Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT (Shashank)
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa6234 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462362322-31278-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit d61992565b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To save a bit of power, let's try to turn off the TMDS output buffers
in DP++ adaptors when we're not driving the port.
v2: Let's not forget DDI, toss in a debug message while at it
v3: Just do the TMDS output control based on adaptor type. With the
helper getting passed the type, we wouldn't actually have to
check at all in the driver, but the check eliminates the debug
output more honest
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b2ccb822d3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.
Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.
Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.
v2: Store adaptor type under indel_hdmi->dp_dual_mode
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
and use it for type1 adaptors as well
Cc: stable@vger.kernel.org
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa6234 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b1ba124d8e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add a helper which aids in the identification of DP dual mode
(aka. DP++) adaptors. There are several types of adaptors
specified: type 1 DVI, type 1 HDMI, type 2 DVI, type 2 HDMI
Type 1 adaptors have a max TMDS clock limit of 165MHz, type 2 adaptors
may go as high as 300MHz and they provide a register informing the
source device what the actual limit is. Supposedly also type 1 adaptors
may optionally implement this register. This TMDS clock limit is the
main reason why we need to identify these adaptors.
Type 1 adaptors provide access to their internal registers and the sink
DDC bus through I2C. Type 2 adaptors provide this access both via I2C
and I2C-over-AUX. A type 2 source device may choose to implement either
of these methods. If a source device implements the I2C-over-AUX
method, then the driver will obviously need specific support for such
adaptors since the port is driven like an HDMI port, but DDC
communication happes over the AUX channel.
This helper should be enough to identify the adaptor type (some
type 1 DVI adaptors may be a slight exception) and the maximum TMDS
clock limit. Another feature that may be available is control over
the TMDS output buffers on the adaptor, possibly allowing for some
power saving when the TMDS link is down.
Other user controllable features that may be available in the adaptors
are downstream i2c bus speed control when using i2c-over-aux, and
some control over the CEC pin. I chose not to provide any helper
functions for those since I have no use for them in i915 at this time.
The rest of the registers in the adaptor are mostly just information,
eg. IEEE OUI, hardware and firmware revision, etc.
v2: Pass adaptor type to helper functions to ease driver implementation
Fix a bunch of typoes (Paulo)
Add DRM_DP_DUAL_MODE_UNKNOWN for the case where we don't (yet) know
the type (Paulo)
Reject 0x00 and 0xff DP_DUAL_MODE_MAX_TMDS_CLOCK values (Paulo)
Adjust drm_dp_dual_mode_detect() type2 vs. type1 detection to
ease future LSPCON enabling
Remove the unused DP_DUAL_MODE_LAST_RESERVED define
v3: Fix kernel doc function argument descriptions (Jani)
s/NONE/UNKNOWN/ in drm_dp_dual_mode_detect() docs
Add kernel doc for enum drm_dp_dual_mode_type
Actually build the docs
Fix more typoes
v4: Adjust code indentation of type2 adaptor detection (Shashank)
Add debug messages for failurs cases (Shashank)
v5: EXPORT_SYMBOL(drm_dp_dual_mode_read) (Paulo)
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1462542412-25533-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit ede53344db)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As a part of WaGsvDisableTurbo, Driver makes an early exit from the
Gen9 Turbo enabling function, so doesn't program the Turbo Control register.
But BIOS could leave the Hw Turbo as enabled, so need to explicitly clear
out the Control register just to avoid inconsitency with debugfs
interface, which will show Turbo as enabled only and that is not expected
after adding the WaGsvDisableTurbo. Apart from this there is no problem
even if the Turbo is left enabled in the Control register, as the Up/Down
interrupts would remain masked.
v2: Add explicit clearing of Turbo Control register to *_disable_rps()
also for the similar consistency (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-2-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There are certain registers, which captures the time elapsed in the
in current Up/Down EI, for how long GT has been Idle/Busy/Avg in the
current Up/Down EI and also in the previous Up/Down EI.
These register values are reported by the i915_frequency_info debugfs
interface. The Driver prints the 'us' suffix after the values, albeit
they are actually in raw form & not in microsecond units.
This patch removes the 'us' suffix so that its clear to User that values
are indeed in raw form.
v2: Present the values in microseconds unit also, after platform
specific conversion (Chris)
v3: Add a space between raw & microsecond value (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-3-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Cc: stable@vger.kernel.org # v4.4
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461237606-16491-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
It's possible that BIOS enables PHY0, but it programmes only the first
channel on it. Since we program the PHYs only during driver loading this
is an incorrect configuration from the driver's point of view, since we
may use both channels eventually. Detect this scenario and force
reprogramming the PHY in this case.
The actual scenario for me was that the lane optimization for the second
channel in PHY0 was not setup by BIOS and so a state verification
warning was triggered. Everything else was setup properly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-4-git-send-email-imre.deak@intel.com
If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461255561-1644-1-git-send-email-imre.deak@intel.com
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-2-git-send-email-imre.deak@intel.com
Remove dev local and use to_i915() in gen8_ppgtt_notify_vgt.
v2: use dev_priv directly for QUESTION_MACROS (Joonas Lahtinen)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461323365-21256-1-git-send-email-matthew.auld@intel.com
Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-5-git-send-email-imre.deak@intel.com
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com
Initially we thought that the platform specific suspend/resume sequences
can be shared between the runtime and system suspend/resume handlers.
This turned out to be not true, we have quite a few differences on most
of the platforms. This was realized already earlier by Paulo who
inlined the platform specific resume_prepare handlers. We have the
same problem with the corresponding suspend_complete handlers, there are
platform differences that make it unfeasible to share the code between
the runtime and system suspend paths. Also now we call functions that
need to be paired like hsw_enable_pc8()/hsw_disable_pc8() from different
levels of the call stack, which is confusing. Fix this by inlining the
suspend_complete handlers too.
This is also needed by the next patch that removes a redundant
uninit/init call during system suspend/resume on BXT.
No functional change.
CC: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
[s/uninline/inline in the commit message]
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-2-git-send-email-imre.deak@intel.com
In commit 5f304c8736 ("drm/i915/kbl: Reset secondary power well requests
left on by DMC/KVMR") I forgot about the fact that SKL==KBL most of the
time and that a secondary MISC IO power well request left on by the DMC is
"expected". Tune down the corresponding WARN to be a debug message. This
was caught by CI suspend tests.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461060036-19043-1-git-send-email-imre.deak@intel.com
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The newly-introduced function i915_gem_object_pin_map() returns an
ERR_PTR (not NULL) if the pin-and-map opertaion fails, so that's what we
must check for. And it's nicer not to assign such a pointer-or-error to
a structure being filled in until after it's been validated, so we
should keep it local and avoid exporting a bogus pointer. Also, for
clarity and symmetry, we should clear 'virtual_start' along with 'vma'
when unmapping a ringbuffer.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Now that we keep the GuC client process descriptor permanently mapped,
we don't really need to keep a local copy of the GuC's work-queue-head.
So we can simplify the code a little by not doing this.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Don't use kmap_atomic() for doorbell & process descriptor access.
This patch fixes the BUG shown below, where the thread could sleep
while holding a kmap_atomic mapping. In order not to need to call
kmap_atomic() in this code path, we now set up a permanent kernel
mapping of the shared doorbell and process-descriptor page, and
use that in all doorbell and process-descriptor related code.
BUG: scheduling while atomic: gem_close_race/1941/0x00000002
Modules linked in: hid_generic usbhid i915 asix usbnet libphy mii
i2c_algo_bit drm_kms_helper cfbfillrect syscopyarea cfbimgblt
sysfillrect sysimgblt fb_sys_fops cfbcopyarea drm coretemp i2c_hid
hid video pinctrl_sunrisepoint pinctrl_intel acpi_pad nls_iso8859_1
e1000e ptp psmouse pps_core ahci libahci
CPU: 0 PID: 1941 Comm: gem_close_race Tainted: G U 4.4.0-160121+ #123
Hardware name: Intel Corporation Skylake Client platform/Skylake AIO
DDR3L RVP10, BIOS SKLSE2R1.R00.X100.B01.1509220551 09/22/2015
0000000000013e40 ffff880166c27a78 ffffffff81280d02 ffff880172c13e40
ffff880166c27a88 ffffffff810c203a ffff880166c27ac8 ffffffff814ec808
ffff88016b7c6000 ffff880166c28000 00000000000f4240 0000000000000001
Call Trace:
[<ffffffff81280d02>] dump_stack+0x4b/0x79
[<ffffffff810c203a>] __schedule_bug+0x41/0x4f
[<ffffffff814ec808>] __schedule+0x5a8/0x690
[<ffffffff814ec927>] schedule+0x37/0x80
[<ffffffff814ef3fd>] schedule_hrtimeout_range_clock+0xad/0x130
[<ffffffff81090be0>] ? hrtimer_init+0x10/0x10
[<ffffffff814ef3f1>] ? schedule_hrtimeout_range_clock+0xa1/0x130
[<ffffffff814ef48e>] schedule_hrtimeout_range+0xe/0x10
[<ffffffff814eef9b>] usleep_range+0x3b/0x40
[<ffffffffa01ec109>] i915_guc_wq_check_space+0x119/0x210 [i915]
[<ffffffffa01da47c>] intel_logical_ring_alloc_request_extras+0x5c/0x70 [i915]
[<ffffffffa01cdbf1>] i915_gem_request_alloc+0x91/0x170 [i915]
[<ffffffffa01c1c07>] i915_gem_do_execbuffer.isra.25+0xbc7/0x12a0 [i915]
[<ffffffffa01cb785>] ? i915_gem_object_get_pages_gtt+0x225/0x3c0 [i915]
[<ffffffffa01d1fb6>] ? i915_gem_pwrite_ioctl+0xd6/0x9f0 [i915]
[<ffffffffa01c2e68>] i915_gem_execbuffer2+0xa8/0x250 [i915]
[<ffffffffa00f65d8>] drm_ioctl+0x258/0x4f0 [drm]
[<ffffffffa01c2dc0>] ? i915_gem_execbuffer+0x340/0x340 [i915]
[<ffffffff8111590d>] do_vfs_ioctl+0x2cd/0x4a0
[<ffffffff8111eac2>] ? __fget+0x72/0xb0
[<ffffffff81115b1c>] SyS_ioctl+0x3c/0x70
[<ffffffff814effd7>] entry_SYSCALL_64_fastpath+0x12/0x6a
------------[ cut here ]------------
v4:
Only tear down doorbell & kunmap() client object if we actually
succeeded in allocating a client object (Tvrtko Ursulin)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93847
Original-version-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvtrko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Since we can only swap out shmemfs objects, those are the only ones that
can influence the ability of the shrinker to free pages. Currently, all
non-shmemfs objects have a raised pages_pin_count to protect them from
the shrinker, so this just makes the logic for can_release_pages()
clearer (and safer in future so that we don't over estimate our ability
to free up pages from future non-swappable objects).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-3-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Inside the shrinker we call can_release_pages() to indicate whether or
not we can make forward progress in freeing up memory by unbinding that
object. When adding our report to oom, we should be using the same
logic.
Whilst here, change the reporting from bytes to pages so that it looks
smaller to the user!, is consistent with the neighbouring oom report
itself which displays counts in pages, and makes the unsigned long
overflow less likely.
v2: Split oversized format string into two lines
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
When iterating over the bound list, we expect all objects there to have
their pages pinned (by the bound VMA). So only report those objects with
additional pin count on their pages as "pinned". These should be those
objects used for display and hardware access.
Reported-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-1-git-send-email-chris@chris-wilson.co.uk
Looks like DPF was not implemented for gen8+ but the IER and IMR
are still enabled on initialization.
Since there is no code to handle this interrupt, gate the irq
enablement behind HAS_L3_DPF in case the feature gets enabled
in the future.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Since commit 30d9aa4265 ("drm/i915: Read sink_count dpcd always"),
the status of a DP connector depends on its sink count value.
However, some eDP panels don't set that value appropriately,
causing them to be reported as disconnected.
Fix this by ignoring sink count for eDP.
v2: Rephrased commit message. (Ander)
In case of eDP, returning status as connected if DPCD
read succeeds to avoid any further operations.
Fixes: 30d9aa4265 ("drm/i915: Read sink_count dpcd always")
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460444034-22320-1-git-send-email-shubhangi.shrivastava@intel.com
In commit 7d23e3c37b ("drm/i915: Cleaning up intel_dp_hpd_pulse") some
much needed clean-up was done, but unfortunately part of the change
broke DP MST. The real issue was setting the connector state to
disconnected in the MST case, which is good, but the code then (after
a goto) checks if the connector state is not connected and shuts down
MST if this is the case, which is bad. With this change both SST and
MST seem to be happy.
v2: Add removed check further up in the function to be sure that MST
is shut down when we lose the link. (Ander)
Fixes: commit 7d23e3c37b ("drm/i915: Cleaning up intel_dp_hpd_pulse")
cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460394684-7036-1-git-send-email-jim.bride@linux.intel.com
Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.
v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We need to kunmap pt_vaddr and not pt itself, otherwise we end up
mapping a bunch of pages without ever unmapping them.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Fixes: d1c54acd67 ("drm/i915/gtt: Introduce kmap|kunmap for dma page")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460476663-24890-4-git-send-email-matthew.auld@intel.com
The power cycle delay starts _after_ turning off the panel power. Do the
msleep after frobbing the pmic panel power gpio.
Also toss in a FIXME about optimizing away needless waits.
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: fc45e82199 ("drm/i915: Use the CRC gpio for panel enable/disable")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460996271-29795-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently we're trying to define HSW/BDW power wells by what's not
included. Let's do it the other way around, so that you can actually
tell when the power well would get enabled. This will also allow us to
add new power domains without accidentally adding it to the HSW/BDW
display power domains.
The current set of domains looks rather buggy even:
- POWER_DOMAIN_MODESET is included in the display power well needlessly
- DDI-B to DDI-E were not part of the display power well when they
should be
So let's fix that up while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we're using POWER_DOMAIN_MASK as the power domains for the
display power well on VLV/CHV. That includes all power domains even
though the disp2d/pipe-a power well is not needed for a lot of things.
Let's reduce these to what we actually need.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.
v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com