If the nvme driver is shutting down its controller, the drievr will not
start the queues up again, preventing blk-mq's hot CPU notifier from
making forward progress.
To fix that, this patch starts a request_queue freeze when the driver
resets a controller so no new requests may enter. The driver will wait
for frozen after IO queues are restarted to ensure the queue reference
can be reinitialized when nvme requests to unfreeze the queues.
If the driver is doing a safe shutdown, the driver will wait for the
controller to successfully complete all inflight requests so that we
don't unnecessarily fail them. Once the controller has been disabled,
the queues will be restarted to force remaining entered requests to end
in failure so that blk-mq's hot cpu notifier may progress.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
nvme_queue is per-cpu queue (mostly). Allocating it in node where blk-mq
will use it.
Signed-off-by: Shaohua Li <shli@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix typos and add the following to the scripts/spelling.txt:
embeded||embedded
Link: http://lkml.kernel.org/r/1481573103-11329-12-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
A device may change capabilities after each reset, e.g. due to a firmware
upgrade. We should thus check for Security Send/Receive and OPAL support
after each reset.
Based on patches from Christoph and Keith.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Adds support for detection of the NVMe controller found in the
following recent MacBooks:
- Retina MacBook 2016 (MacBook9,1)
- 13" MacBook Pro 2016 without Touch Bar (MacBook13,1)
- 13" MacBook Pro 2016 with Touch Bar (MacBook13,2)
Signed-off-by: Daniel Roschka <danielroschka@phoenitydawn.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This will enable the user to control the specific interface for
connection establishment in case the host has more than 1 interface
under the same subnet.
E.g:
Host interfaces configured as:
- ib0 1.1.1.1/16
- ib1 1.1.1.2/16
Target interfaces configured as:
- ib0 1.1.1.3/16 (listener interface)
- ib1 1.1.1.4/16
the following connect command will go through host iface ib0 (default):
nvme connect -t rdma -n testsubsystem -a 1.1.1.3 -s 1023
but the following command will go through host iface ib1:
nvme connect -t rdma -n testsubsystem -a 1.1.1.3 -s 1023 -w 1.1.1.2
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This will enable the usage for nvme rdma target.
Also move from a lookup array to a switch statement.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Discovery controllers don't set the values. They are in reserved
areas of the Identify Controller data structure.
Given the cmd completed, the minimal capsule sizes are supported,
so no need to check nqn to detect discovery controllers and
special case validations.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This driver previously required we have a special check for IO submitted
to nvme IO queues that are temporarily suspended. That is no longer
necessary since blk-mq provides a quiesce, so any IO that actually gets
submitted to such a queue must be ended since the queue isn't going to
start back up.
This is fixing a condition where we have fewer IO queues after a
controller reset. This may happen if the number of CPU's has changed,
or controller firmware update changed the queue count, for example.
While it may be possible to complete the IO on a different queue, the
block layer does not provide a way to resubmit a request on a different
hardware context once the request has entered the queue. We don't want
these requests to be stuck indefinitely either, so ending them in error
is our only option at the moment.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a namespace has already been marked dead, we don't want to kick the
request_queue again since we may have just freed it from another thread.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the device is not present, the driver should disable the queues
immediately. Prior to this, the driver was relying on the watchdog timer
to kill the queues if requests were outstanding to the device, and that
just delays removal up to one second.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
NVMe devices can advertise multiple power states. These states can
be either "operational" (the device is fully functional but possibly
slow) or "non-operational" (the device is asleep until woken up).
Some devices can automatically enter a non-operational state when
idle for a specified amount of time and then automatically wake back
up when needed.
The hardware configuration is a table. For each state, an entry in
the table indicates the next deeper non-operational state, if any,
to autonomously transition to and the idle time required before
transitioning.
This patch teaches the driver to program APST so that each successive
non-operational state will be entered after an idle time equal to 100%
of the total latency (entry plus exit) associated with that state.
The maximum acceptable latency is controlled using dev_pm_qos
(e.g. power/pm_qos_latency_tolerance_us in sysfs); non-operational
states with total latency greater than this value will not be used.
As a special case, setting the latency tolerance to 0 will disable
APST entirely. On hardware without APST support, the sysfs file will
not be exposed.
The latency tolerance for newly-probed devices is set by the module
parameter nvme_core.default_ps_max_latency_us.
In theory, the device can expose "default" APST table, but this
doesn't seem to function correctly on my device (Samsung 950), nor
does it seem particularly useful. There is also an optional
mechanism by which a configuration can be "saved" so it will be
automatically loaded on reset. This can be configured from
userspace, but it doesn't seem useful to support in the driver.
On my laptop, enabling APST seems to save nearly 1W.
The hardware tables can be decoded in userspace with nvme-cli.
'nvme id-ctrl /dev/nvmeN' will show the power state table and
'nvme get-feature -f 0x0c -H /dev/nvme0' will show the current APST
configuration.
This feature is quirked off on a known-buggy Samsung device.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, all NVMe quirks are based on PCI IDs. Add a mechanism to
define quirks based on identify_ctrl's vendor id, model number,
and/or firmware revision.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
nvmf_create_ctrl() relys on the presence of a create_crtl callback in the
registered nvmf_transport_ops, so make nvmf_register_transport require one.
Update the available call-sites as well to reflect these changes.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch defines CNS field as 8-bit field and avoids cpu_to/from_le
conversions.
Also initialize nvme_command cns value explicitly to NVME_ID_CNS_NS
for readability (don't rely on the fact that NVME_ID_CNS_NS = 0).
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Easier for debugging and testing state machine
transitions.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We need to verify that the controller supports the security
commands before actually trying to issue them.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
[hch: moved the check so that we don't call into the OPAL code if not
supported]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Insted of bloating the containing structure with it all the time this
allocates struct opal_dev dynamically. Additionally this allows moving
the definition of struct opal_dev into sed-opal.c. For this a new
private data field is added to it that is passed to the send/receive
callback. After that a lot of internals can be made private as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Scott Bauer <scott.bauer@intel.com>
Reviewed-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When CONFIG_KASAN is enabled, compilation fails:
block/sed-opal.c: In function 'sed_ioctl':
block/sed-opal.c:2447:1: error: the frame size of 2256 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Moved all the ioctl structures off the stack and dynamically allocate
using _IOC_SIZE()
Fixes: 455a7b238c ("block: Add Sed-opal library")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
NVMe supports up to 256 ranges per DSM command, so wire up support
for ranged discards up to that limit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch implements the necessary logic to unlock an Opal
enabled device coming back from an S3.
The patch also implements the SED/Opal allocation necessary to support
the opal ioctls.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of keeping two levels of indirection for requests types, fold it
all into the operations. The little caveat here is that previously
cmd_type only applied to struct request, while the request and bio op
fields were set to plain REQ_OP_READ/WRITE even for passthrough
operations.
Instead this patch adds new REQ_OP_* for SCSI passthrough and driver
private requests, althought it has to add two for each so that we
can communicate the data in/out nature of the request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This can be used to check for fs vs non-fs requests and basically
removes all knowledge of BLOCK_PC specific from the block layer,
as well as preparing for removing the cmd_type field in struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch sets the aborted flag only if an abort was sent, reducing
excessive kernel message spamming for completed IO that wasn't actually
aborted.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
When the lightnvm core had the "gennvm" layer between the device and the
target, there was a need for the core to be able to figure out which
target it should send an end_io callback to. Leading to a "double"
end_io, first for the media manager instance, and then for the target
instance. Now that core and gennvm is merged, there is no longer a need
for this, and a single end_io callback will do.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Enable user-space to issue vector I/O commands through ioctls. To issue
a vector I/O, the ppa list with addresses is also required and must be
mapped for the controller to access.
For each ioctl, the result and status bits are returned as well, such
that user-space can retrieve the open-channel SSD completion bits.
The implementation covers the traditional use-cases of bad block
management, and vectored read/write/erase.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Metadata implementation, test, and fixes.
Signed-off-by: Simon A.F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The number of configuration groups has been limited to one in current
code, even if there is support for up to four. With the introduction
of the open-channel SSD 1.3 specification, only a single
group is exposed onwards. Reflect this in the nvm_id structure.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For the first iteration of Open-Channel SSDs, it was anticipated that
there could be various media managers on top of an open-channel SSD,
such to allow vendors to plug in their own host-side FTLs, without the
media manager in between.
Now that an Open-Channel SSD is exposed as a traditional block device,
there is no longer a need for this. Therefore lets merge the gennvm code
with core and simplify the stack.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The NVMe SCSI emulation doesn't use BLOCK_PC requests, so BLK_MAX_CDB
doesn't have a meaning for it. Instead opencode the value of 16
and refactor the code a bit so that related checks are next to each
other and we only need to use the value in one place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since we moved the cdb parts and define out of the block proper,
we need to include scsi/scsi_request.h for the nvme scsi layer.
Fixes: 82ed4db499 ("block: split scsi_request out of struct request")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@fb.com>
Without this deallocate won't work properly due to the mismatch
of the bio/request size and the actual payload size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Add Kconfig entries to manage what devices get assigned an MQ
scheduler, and add a blk-mq flag for drivers to opt out of scheduling.
The latter is useful for admin type queues that still allocate a blk-mq
queue and tag set, but aren't use for normal IO.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
The new blk_rq_payload_bytes generalizes the payload length hacks
that nvme_map_len did before.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 54adc01055 ("nvme/quirk: Add a delay before checking for adapter
readiness") introduced a quirk to adapters that cannot read the bit
NVME_CSTS_RDY right after register NVME_REG_CC is set; these adapters
need a delay or else the action of reading the bit NVME_CSTS_RDY could
somehow corrupt adapter's registers state and it never recovers.
When this quirk was added, we checked ctrl->tagset in order to avoid
quirking in probe time, supposing we would never require such delay
during probe. Well, it was too optimistic; we in fact need this quirk
at probe time in some cases, like after a kexec.
In some experiments, after abnormal shutdown of machine (aka power cord
unplug), we booted into our bootloader in Power, which is a Linux kernel,
and kexec'ed into another distro. If this kexec is too quick, we end up
reaching the probe of NVMe adapter in that distro when adapter is in
bad state (not fully initialized on our bootloader). What happens next
is that nvme_wait_ready() is unable to complete, except if the quirk is
enabled.
So, this patch removes the original ctrl->tagset verification in order
to enable the quirk even on probe time.
Fixes: 54adc01055 ("nvme/quirk: Add a delay before checking for adapter readiness")
Reported-by: Andrew Byrne <byrneadw@ie.ibm.com>
Reported-by: Jaime A. H. Gomez <jahgomez@mx1.ibm.com>
Reported-by: Zachary D. Myers <zdmyers@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jeffrey Lien <Jeff.Lien@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we don't abuse the cmd field in struct request for nvme command
passthrough this function needs to be converted to the proper accessor
as well.
Fixes: d49187e97e ("nvme: introduce struct nvme_request")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Christoph writes:
The most significant one is that we've agreed on shared maintaince and
a common repository for the PCIe NVMe driver and NVMe over Fabrics. The
target code still only has a subset of the maintainers but goes through
the same tree as well. Keith, Sagi and me will take turns at collecting
patches and sending you pull requests.
Simplify the error handling of nvme_fc_create_hw_io_queues(), this saves us
one variable and one level of indentation.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviwed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Dan Carpenters's tool caught a pointer reference - should have been
just ptr, not &ptr.
Don't bother. Remove the pointer value in the printf. Its irrelevant.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that the broken power state control is gone, it appears to serve
no purpose. Just delete it. NVME devices don't have a concept of
started vs stopped anyway.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is not theoretically possible for this driver to wrap twice while
processing completions. The driver allocates only 'queue_depth - 1'
tags, so there can never be more than that to reap when processing a
completion queue. Removing this misleading comment makes it a little
less likely people with broken controllers will blame the driver for
their spurious interrupts.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some OEMs believe they own the Identify Controller vendor specific
region and will repurpose it with their own values. While not common,
we can't rely on the PCI VID:DID to tell use how to decode the field
we reserved for this as the stripe size so we need to do something else
for the list of devices using this quirk.
The field was supposed to allow flexibility on the device's back-end
striping, but it turned out that never materialized; the chunk is always
the same as MDTS in the products subscribing to this quirk, so this
patch removes the stripe_size field and sets the chunk to the max hw
transfer size for the devices using this quirk.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make sure we are using the correct scnprintf in the sysfs show
function for the CMB.
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by Jon Derrick: <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
- Shared mlx5 updates with net stack (will drop out on merge if Dave's
tree has already been merged)
- Driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- Debug cleanups
- New connection rejection helpers
- SRP updates
- Various misc fixes
- New paravirt driver from vmware
-----BEGIN PGP SIGNATURE-----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=QeGy
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is the complete update for the rdma stack for this release cycle.
Most of it is typical driver and core updates, but there is the
entirely new VMWare pvrdma driver. You may have noticed that there
were changes in DaveM's pull request to the bnxt Ethernet driver to
support a RoCE RDMA driver. The bnxt_re driver was tentatively set to
be pulled in this release cycle, but it simply wasn't ready in time
and was dropped (a few review comments still to address, and some
multi-arch build issues like prefetch() not working across all
arches).
Summary:
- shared mlx5 updates with net stack (will drop out on merge if
Dave's tree has already been merged)
- driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- debug cleanups
- new connection rejection helpers
- SRP updates
- various misc fixes
- new paravirt driver from vmware"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (210 commits)
IB: Add vmw_pvrdma driver
IB/mlx4: fix improper return value
IB/ocrdma: fix bad initialization
infiniband: nes: return value of skb_linearize should be handled
MAINTAINERS: Update Intel RDMA RNIC driver maintainers
MAINTAINERS: Remove Mitesh Ahuja from emulex maintainers
IB/core: fix unmap_sg argument
qede: fix general protection fault may occur on probe
IB/mthca: Replace pci_pool_alloc by pci_pool_zalloc
mlx5, calc_sq_size(): Make a debug message more informative
mlx5: Remove a set-but-not-used variable
mlx5: Use { } instead of { 0 } to init struct
IB/srp: Make writing the add_target sysfs attr interruptible
IB/srp: Make mapping failures easier to debug
IB/srp: Make login failures easier to debug
IB/srp: Introduce a local variable in srp_add_one()
IB/srp: Fix CONFIG_DYNAMIC_DEBUG=n build
IB/multicast: Check ib_find_pkey() return value
IPoIB: Avoid reading an uninitialized member variable
IB/mad: Fix an array index check
...
