This functionality has already been implemented in the cx20442 codec
driver (commit f75a8ff67d, "ASoC: cx20442:
add bias control over a platform provided regulator"), no need to keep
it here duplicated.
Once done, remove the no longer used AMS_DELTA_LATCH2_MODEM_NRESET
symbol from the board header file and a call to the regulator_toggle()
helper function from the old API wrapper found in the board file. While
being at it, simplify the way the modem .pm callback handles the
regulator and drop that helper function and its related consumer setup
completely.
Depends on patches 1/3 and 2/3 for clean apply and keep things working.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the CX20442 codec driver already takes care of enabling the codec
power for itself (commit f75a8ff67d,
"ASoC: cx20442: add bias control over a platform provided regulator"),
but before dropping the old bias control method from the Amstrad Delta
ASoC sound card file, which in fact keeps the modem power always on,
even on the ASoC device close for now, extend the modem setup with a
power management callback which toggles the regulator up to the modem's
needs, reusing the previously set up regulator consumer for this. Also,
drop the MODEM_NRESET pin setup from the modem initialization procedure,
as this operation was already ineffective since patch 1/3, and not
needed because the regulator is set up as initially enabled.
Depends on patch 1/3 "ARM: OMAP1: ams-delta: set up regulator over modem
reset GPIO pin" to apply cleanly.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Amstrad Delta on-board latch2 bit named MODEM_NRESET, now available
as a GPIO pin AMS_DELTA_GPIO_PIN_NMODEM_RESET, is used to power up/down
(bring into/out of a reset state) two distinct on-board devices
simultaneously: the modem, and the voice codec. As a consequence, that
bit is, or can be, manipulated concurrently by two drivers, or their
platform provided hooks.
Instead of updating those drivers to use the gpiolib API as a new method
of controlling the MODEM_NRESET pin state, like it was done to other
drivers accessing latch2 pins, and still being vulnerable to potential
concurrency conflicts, or trying to solve that sharing issue with a
custom piece of code, set up a fixed regulator device on top of that
GPIO pin, with the intention of updating both drivers to manipulate that
regulator, not the GPIO pin directly.
Before the ASoC driver is updated and the modem platform data expanded
with a power management callback for switching its power, the
ams_delta_latch_write() function, which still provides the old API for
accessing latch2 functionality from not updated drivers, is modified to
toggle the regulator instead of the MODEM_NRESET GPIO pin. A helper
function provided for balancing the regulator enable/disable operations,
together with the consumer data needed for tracking the regulator state,
will be removed once the drivers are updated.
Depends on patch series "ARM: OMAP1: ams-delta: replace custom I/O with
GPIO".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The main purpose of this patch is to fix several section mismatch
warnings from the board file and a few board specific drivers,
introduced with recent Amstrad Delta patch series, some of them rising
up only when building with CONFIG_MODULES not set.
While being at it, section tagging of all init data found in the board
file have been revised and hopefully corrected and/or optimized.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While resolving section mismatches introduced with recent patches
to for-next, a few dangerous, driver bind/unbind unaware section
tagging already present in mainline have been identified. Fix them.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't use Amstrad Delta custom I/O functions once GPIO interface is
available for the underlying hardware.
While requesting and initializing GPIO pins used, also take care of one
extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs
to the device and affects its functioning.
Once done, move the driver initialization back to the device_initcall
level, reverting the temporary chane introduced with patch 1/7 "ARM:
OMAP1: ams-delta: register latch dependent devices later". That change
is no longer required once the driver takes care of registering used
GPIO pins, and it's better to initialize the device before others using
the latch2 based GPIO pins, otherwise a garbage is reported on boot,
perhaps due to random data already captured by the FIQ handler while the
keyboard related latch bits are written with random values during
initialization of those other latch2 dependent devices.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[tony@atomide.com: renamed _gpios to ams_delta_gpios]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions for controlling the device,
use GPIO API instead.
While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the Amstrad Delta on-board latches have been converted to GPIO
devices, use the generic driver to control on-board LEDs which hang off
those latches.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once ready, ams-delta specific device drivers currently calling custom
ams_delta_latch[12]_write() functions can be updated to call generic
gpio_set_value() instead, which will make them less platform dependent.
Even more, some custom ams-delta only drivers can perhaps be dropped
from the tree after converting selected ams-delta platform devices to
follow generic GPIO based device models.
The latch_gpios[] table is initially filled with all latch1 and latch2
GPIO pins in order to register and initialize them from the board file
until those are handled by respective existing device drivers (leds,
nand, lcd, serio, asoc, serial). That table will get almost empty after
the transision process is completed, holding only pins not used by any
drivers / connected to unused devices, in order to initialize them from
the board file for power saving purposes.
The new ams_delta_latch_write() function is a unified replacement for
those removed ams_delta_latch[12]_write(), and serves as a temporary
wrapper over gpio_set_value(), providing the old API for those not yet
updated device drivers, and will be removed after all custom drivers are
converted or replaced.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation to converting Amstrad Delta on-board latches to
basic_mmio_gpio devices, registration of platform devices which depend
on latches and will require initialization of their GPIO pins first,
should be moved out of .machine_init down to late_initcall level, as the
gpio-generic driver is not available until device_initcall time. The
latch reset operation, which will be replaced with GPIO initialization,
must also be moved to late_initcall for the same reason.
Since there was already another, separate arch_initcall function for
setting up one of those latch dependent devices, the on-board modem
device, reuse that function, i.e., rename it to a name that matches the
new purpose, extend with other device setup relocated from
.machine_init, and move down to the late_initcall level.
While being at it, add missing gpio_free() in case the modem platform
device registration fails.
Thanks to Tony Lindgren <tony@atomide.com> who suggested this approach
instead of shifting up the gpio-generic driver initialization.
In addition, defer registration of the Amstrad Delta ASoC and serio
devices, done from their device driver files, until late_initcall time,
as those drivers will depend on their GPIO pins already requested from
the board late_init() function until updated to register their GPIO pins
themselves.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7b88e62f5d (ARM: OMAP1: Use generic
map_io, init_early and init_irq) changed omap1 to use generic map_io.
Looks like I missed one board though. Fix this by adding a custom
map_io for Amstrad E3.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This allows removing omap hacks for map_io allowing generic
map_io.
Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pointers to statically declared platform device structures which are
registered with platform_device_register() are then used during run time
to access these structure members, for example from platform_uevent()
and much more. Therefore, these structures should never be placed inside
sections which are dropped after boot. Fix platform devices incorrectly
tagged with __initdata which happen to exist inside OMAP sub-trees.
This bug has exhibited itself on my ARM/OMAP1 based Amstrad Delta
videophone after commit 6d3163ce86, "mm:
check if any page in a pageblock is reserved before marking it
MIGRATE_RESERVE", resulting in reading from several
/sys/device/platform/*/uevent files always ending up with segmentation
faults.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Varadarajan, Charulatha <charu@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed for the following patches so we can initialize the
rest of the hardware timers later on.
As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.
Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
This allows us to remove cpu_is_omap calls from init_irq functions.
There should not be any need for cpu_is_omap calls as at this point.
During the timer init we only care about SoC generation, and not about
subrevisions.
The main reason for the patch is that we want to initialize only
minimal omap specific code from the init_early call.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
after these changes omap1_defconfig and omap2plus_defconfig don't have any
section mismatches any more, making it plausible that the patches earlier
in this series are OK.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following section mismatches:
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x491c): Section mismatch
in reference from the variable fsample_config to the (unknown reference)
.init.data:(unknown)
The variable fsample_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x8f0c): Section mismatch
in reference from the variable ams_delta_config to the (unknown
reference) .init.data:(unknown)
The variable ams_delta_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x93ac): Section mismatch
in reference from the variable ams_delta_camera_device to the (unknown
reference) .init.data:(unknown)
The variable ams_delta_camera_device references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x5e94): Section mismatch in reference from the
variable fsample_config to the (unknown reference) .init.data:(unknown)
The variable fsample_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0xa484): Section mismatch in reference from the
variable ams_delta_config to the (unknown reference)
.init.data:(unknown)
The variable ams_delta_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0xa924): Section mismatch in reference from the
variable ams_delta_camera_device to the (unknown reference)
.init.data:(unknown)
The variable ams_delta_camera_device references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
There is a common requirement for not using OMAP specific omap_readw() /
omap_writew() function calls in drivers/, but replace them with
readw() / writew() on ioremap()ped addresses passed from arch/ instead.
The patch implements this idea for the Amstrad Delta NAND driver. To be
able to use the modified driver, the board file is updated with the
platform device I/O resource declaration, which is passed from there.
Created and tested against linux-2.6.37-rc5, on top of recent patch
'MTD: NAND: ams-delta: convert to platform driver'.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In its current form, the driver may interfere with different hardware on
different boards if built into the kernel, hence is not suitable for
inclusion into a defconfig, inteded to be usable with multiple OMAP1 cpu and
machine types.
Convert it to a platform driver, that should be free from this issue.
Created and tested against linux-2.6.37-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Most keypad drivers make use of the <linux/input/matrix_keypad.h>
defined macros, structures and inline functions.
Convert omap-keypad driver to use those as well, as suggested by a
compile time warning, hardcoded into the OMAP <palt/keypad.h>.
Created against linux-2.6.37-rc5.
Tested on Amstrad Delta.
Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to
board-h4.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches removes a config option that was used to select a FIQ
handler to be build for Amstrad Delta, as required by the on-board serio
interface driver. Not having any problem reports received since it was
introduced in 2.6.35, the FIQ handler can now be built and initialized by
default, thus reqiring no extra config option.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use IOMEM() macro to get rid of the following sparse warning:
arch/arm/mach-omap1/board-ams-delta.c:319:36: warning: incorrect type in initializer (different address spaces)
arch/arm/mach-omap1/board-ams-delta.c:319:36: expected void [noderef] <asn:2>*membase
arch/arm/mach-omap1/board-ams-delta.c:319:36: got void *<noident>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
This patch extends the Amstrad Delta camera support with LEDS trigger that can
be used for automatic control of the on-board camera LED. The led turns on
automatically on camera device open and turns off on camera device close.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds configuration data and initialization code required for camera
support to the Amstrad Delta board.
Three devices are declared: SoC camera, OMAP1 camera interface and OV6650
sensor.
Default 12MHz clock has been selected for driving the sensor. Pixel clock has
been limited to get reasonable frame rates, not exceeding the board
capabilities. Since both devices (interface and sensor) support both pixel
clock polarities, decision on polarity selection has been left to drivers.
Interface GPIO line has been found not functional, thus not configured.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch adds initialization of FIQ related handlers to the Amstrad Delta
videophone board code. FIQ will be used instead of a traditional IRQ for
processing all GPIO generated interrupts, including a keyboard serial clock
line.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of Amstrad Delta modem utilized GPIO line, interrupt is requested from
standard serial8250 driver code without first requesting the GPIO pin itself.
Even if it works with default OMAP GPIO interrupt handler, it appeared not
compatible with recent, optimized version of the board GPIO FIQ handler,
required for fast processing of interrupts generated by other GPIO pin that a
serial keyboard clock hangs off.
This patch fills the board specific modem initialization routine with common
GPIO line reservation and direction setup.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
