hard_header_len provides limitations for things like AF_PACKET, such
that we don't allow transmitting packets smaller than this.
needed_headroom provides a suggested minimum headroom for SKBs, so that
we can trivally add our headers to the front.
The latter is the correct field to use in this case, while the former
mostly just prevents sending small AF_PACKET frames.
In any case, mwifiex already does its own bounce buffering [1] if we
don't have enough headroom, so hints (not hard limits) are all that are
needed.
This is the essentially the same bug (and fix) that brcmfmac had, fixed
in commit cb39288fd6 ("brcmfmac: use ndev->needed_headroom to reserve
additional header space").
[1] mwifiex_hard_start_xmit():
if (skb_headroom(skb) < MWIFIEX_MIN_DATA_HEADER_LEN) {
[...]
/* Insufficient skb headroom - allocate a new skb */
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.gbhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unneeded variable ret used to store return value.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The simple_strtol() function is deprecated since it does not
check for the range overflow. Use kstrtoint() instead.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unused fab_version member from struct rtw_hal.
Some of the checks being made were nonsense.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports only STA as primary interface in repeater mode.
Since the only meaningful usage of AP + STA interface combination
is repeater, reject such combination with AP as primary interface.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Quantenna Pearl device exposes multiple (up to 3) radio interfaces under
single PCIe function. So far all the wiphy devices were attached to the
same pcie device. As a result, all different wireless network devices
were reported under the same sysfs directory for pcie device, e.g.:
$ ls /sys/class/net/wlan0/device/net/
wlan0 wlan1
It turns out that such behavior may confuse various users of wireless
subsystem. For instance, it turned out to be the case for:
- Linux init systems, e.g. for renaming based on parent device
- OpenWRT configuration scripts
Suggested solution is to add an intermediate virtual platform device
for each radio interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that edmg field of cfg80211_chan_def structure is properly
initialized by zeros. Otherwise cfg80211_chandef_valid may return
false if edmg fields contain some garbage.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable WPA3 OWE support in AP mode. Driver currently supports cards that
offload OWE processing to userspace. This patch adds all the required
tools for such offloading. Firmware requests OWE processing sending new
UPDATE_OWE event to driver, which uses cfg80211_update_owe_info_event to
notify userspace software. After OWE processing is completed, userspace
sends calculated IEs to firmware using update_owe_info cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable WPA3 SAE support in AP mode. Driver currently supports cards
that offload SAE authentication to userspace. So allow userspace
software to subscribe and to send AUTH frames. Besides, enable
AP mode support in external_auth cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some unexplained reason, commit d1d1a96bdb ("rtlwifi: rtl8188ee:
Remove local configuration variable") broke at least one system. As
the only net effect of the change was to remove 2 bytes from the start
of struct phy_status_rpt, this patch adds 2 bytes of padding at the
beginning of the struct.
Fixes: d1d1a96bdb ("rtlwifi: rtl8188ee: Remove local configuration variable")
Cc: Stable <stable@vger.kernel.org> # V5.4+
Reported-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Tested-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: ath11k@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to
reconfigure HW's maximum txpower.
This fixes 0dBm txpower setting when user attaches to an interface for
the first time with the following scenario:
ieee80211_do_open()
ath9k_add_interface()
ath9k_set_txpower() /* Set TX power with not yet initialized
sc->hw->conf.power_level */
ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and
raise IEEE80211_CONF_CHANGE_POWER */
ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */
This issue can be reproduced with the following:
$ modprobe -r ath9k
$ modprobe ath9k
$ wpa_supplicant -i wlan0 -c /tmp/wpa.conf &
$ iw dev /* Here TX power is either 0 or 3 depending on RF chain */
$ killall wpa_supplicant
$ iw dev /* TX power goes back to calibrated value and subsequent
calls will be fine */
Fixes: 283dd11994 ("ath9k: add per-vif TX power capability")
Cc: stable@vger.kernel.org
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The CONFIG_ATH5K_AHB could be enabled on ATH25 system without enabling
ATH5K driver itself. This does not make sense because CONFIG_ATH5K_AHB
controls object build within drivers/net/wireless/ath/ath5k/ so enabling
it without CONFIG_ATH5K brings nothing.
Add proper dependency to CONFIG_ATH5K_AHB.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware is in a bad state or not initialized fully, sending
the DBGC_SUSPEND_RESUME command fails but we can still collect logs.
Instead of aborting the entire dump process, simply ignore the error.
By removing the last callpoint that was checking the return value, we
can also convert the function to return void.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 576058330f ("iwlwifi: dbg: support debug recording suspend resume command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.dcec37b2efd4.I8dcd190431d110a6a0e88095ce93591ccfb3d78d@changeid
The TLV offset is only used to read registers, while the offset used for
the FIFO addresses are hard coded in the driver and not given by the
TLV.
If we try to apply the TLV offset when reading the FIFOs, we'll read
from invalid addresses, causing the driver to hang.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 8d7dea25ad ("iwlwifi: dbg_ini: implement Rx fifos dump")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.fbab869c26fa.I4ddac20d02f9bce41855a816aa6855c89bc3874e@changeid
We were erroneously checking the length of the tlv instead of checking
the pointer returned by kmemdup() when allocating dbg_conf_tlv[].
This was probably a typo. Fix it by checking the returned pointer
instead of the length.
Reported-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151128.06e00e6e980f.I9a890ce83493b79892a5f690d12016525317fa7e@changeid
The AP may set the LDPC capability only in HE (IEEE80211_HE_PHY_CAP1),
but we were checking it only in the HT capabilities.
If we don't use this capability when required, the DSP gets the wrong
configuration in HE and doesn't work properly.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: befebbb30a ("iwlwifi: rs: consider LDPC capability in case of HE")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151128.492d167c1a25.I1ad1353dbbf6c99ae57814be750f41a1c9f7f4ac@changeid
First set of patches for v5.7. Lots of mt76 patches as they missed the
v5.6 deadline and hence they were postponed to the next version.
Otherwise nothing special standing out.
mt76
Major changes:
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
brcmfmac
* support BRCM 4364 found in MacBook Pro 15,2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeYQnTAAoJEG4XJFUm622bVEkH/13OGWPYjWQXeAFeMFiukSp0
NJk9s6xRQmzuLxJsharKfwpr1hVm93ZZpGCG8RGCRAlMJqRnRT9q429YNFcpbWFY
NIfsioktIk7wbyXiw6p73z+vlvRgCYTQ/QCr19731xRli2JCNh9ZYzAOA6I6iX8v
7nCcRLLm4NM/+L+iybBumgNB4/5CCRgQTJQqbtvrgDQYXLMtu6HqcHQ1ldzivM9U
cs9c25tthC5Zv7YhAscVRDys4ca1o/gJr7VB6surTqLCx02LmgUjBZQ9ZFqabSBa
hkumUGivGkRN6yW1CDYu+Gok5ij0a/A3QQ9Hy5gAq1KrjtUKXbZeFVNSBSiKtQQ=
=kUdG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
First set of patches for v5.7. Lots of mt76 patches as they missed the
v5.6 deadline and hence they were postponed to the next version.
Otherwise nothing special standing out.
mt76
Major changes:
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
brcmfmac
* support BRCM 4364 found in MacBook Pro 15,2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* EEPROM fixes
* MAC address handling fixes
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* minor cleanups/fixes for all drivers
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAl5G3tEACgkQ130UHQKnbvXVtgCdEBlcmjViCqkCPXStdSxUy9o9
JCsAn2TnPduCoTCB1jo1foJbNXn5XzuG
=Z/l3
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2020-02-14' of https://github.com/nbd168/wireless
mt76 patches for 5.7
* dual-band concurrent support for MT7615
* fixes for rx path race conditions
* EEPROM fixes
* MAC address handling fixes
* coverage class support for MT7615
* beacon fixes for USB devices
* MT7615 LED support
* minor cleanups/fixes for all drivers
* set_antenna support for MT7615
* tracing improvements
* preparation for supporting new USB devices
* tx power fixes
If the hardware receives an oversized packet with too many rx fragments,
skb_shinfo(skb)->frags can overflow and corrupt memory of adjacent pages.
This becomes especially visible if it corrupts the freelist pointer of
a slab page.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that there is support for BIGTK configuration and AP/STA
functionality for using BIP with Beacon frames, indicate support for the
Beacon protection functionality.
Johannes: move this to hwsim, since it's not clear that all drivers
using mac80211 will do this correctly - lots of them modify the
beacon before transmission e.g. to update the TIM element, and that
would obviously break the signature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-7-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As of 6-DEC-2019, NXP has acquired Marvell’s Wireless business
unit. This change is to update the license text accordingly.
Signed-off-by: James Cao <zheng.cao@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of rx_mask in mt7615_eeprom_parse_hw_cap routine since it is not
actually used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename usb stat_wq in wq in order to be reused not just for gathering hw
tx statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set RX scatter gather number to 4 in order to extend the maximum AMSDU
size to 11,454.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As previous devices, mt7622 relies on multiple hw queues while for
mt7615 we have just on per band hw queue and the mcu demux the traffic
according to the packet AC. In order to dump all configured hw queues,
rely on mt76_queues_read for mt7622 in mt7615 debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwriting the RMAC_CHFREQ register is not reliable enough, as the firmware
could potentially write it again.
Since there is no PHY index indication in the rx info, we need to use another
way:
If both PHYs are using different channels, find the PHY where chfreq matches
the register value.
The only corner case remaining is when both PHYs are using the same channel.
In that case, the per-packet noise value on the primary PHY will have
information belonging to the chains of the secondary PHY from the previous
received packet of that PHY. The secondary PHY will set noise to 0 for extra
chains.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not set the tx/rx start bits in MT_MAC_SYS_CTRL from within initvals.
The driver sets these later when the hardware is ready
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The second PHY receives no packets unless there is an active vif present.
Set the WANT_MONITOR_VIF flag to deal with that
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To adapt new firmware version.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To adapt new firmware version.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reduce command/event times, newer firmware adds a tag
sta_rec_wtbl to take care of WTBL operations.
MCU_EXT_CMD_WTBL_UPDATE is deprecated.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add fw_ver in mt7615_dev to check firmware version, and adjust
mt7615_mcu_send_sta_rec() to adapt firmware v2 changes.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Operating command is simpler and just as clear
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu_add_wtbl and mcu_set_ht_cap into mcu_set_sta to simplify flow.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move set_bmc_wtbl into sta_rec function to simplify flow.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Setting the tx power by manipulating EEPROM may in some cases not be enough,
since it only covers the base target power and not per-rate offsets.
In other cases, it could limit tx power of rates too much, possibly reducing
throughput or range.
Use firmware support for applying per-rate limit and power offsets for
different values of Nss.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7622 does not have the CR4 microcontroller sitting in the data path.
Because of that, it uses the chip's native tx descriptor format instead of
something parsed and converted by the firmware.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
MT7622 does not have a CR4 microcontroller, so it only uses its own N9
firmware.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When sending EEPROM data to the MCU, MT7622 uses a longer buffer
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7622 queue mapping is different from MT7615 and requires an extra dma
scheduler init and a few register tweaks
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7622 uses more interrupt bits for queue tx completion events.
Enabling those extra bits is harmless on MT7615
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The beginning of the struct is guaranteed to be 4-byte aligned, and this
attribute allows the compiler to generate more efficient code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ring is used for looping back tx powersave filtered frames, so it could
use some more room, in case more than one aggregate was queued
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes a theoretical issue where it could potentially overwrite an existing
descriptor entry (and leaking its skb)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Avoids a theoretical corner case where the hardware could try to process
a stale descriptor after a watchdog reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Define MT_DRV_RX_DMA_HDR flag in drv_flag in order to not skip rx frame
dma header since new devices (e.g. mt7663u) reports rx frame info in the
usb dma header
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to support mt7663u usb dongles
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_skb_dma_info utility routine in mt76-usb module in order
to be reused adding mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7663u devices rely on a different endpoint mapping. Take it into account
in mt76u_alloc_tx routine
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76u_alloc_mcu_queue utility routine to allocate mcu hw rx queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Resume all possible rx queues after suspend. This is a preliminary patch
to support mt7663u devices
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76_queue parameter to mt76u_rx_urb_alloc signature since this
routine will be used to allocate urbs for mcu hw queue used by new
chipset generation (e.g. mt7663u). Check sg_max_size in in
mt76u_urb_alloc in order to use linear urb for mcu queue
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_alloc_rx_queue routine to allocate rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stop/free all configured rx queues (data/mcu) in
mt76u_stop_rx/mt76u_free_rx. This is a preliminary patch to support new
devices (e.g. mt7663u) that rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_free_rx_queue utility routine to free rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu buffer allocation in mt76x2u/mt76x0u drivers since newer
chipsets (e.g. mt7663u) does not rely on synchronous mcu communication
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add queue_id parameter to mt76u_submit_rx_buffers in order to reuse it
adding mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reuse mt76u_complete_rx for both data and mcu rx queue, rely
on mt76_queue as urb context in mt76u_complete_rx. Moreover set usb rx
endoint according to rx queue in mt76u_submit_rx_buf. This is a
preliminary patch to add mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_queue parameter to mt76u_refill_rx signature in order to
reuse it for mcu hw rx queue
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_queue pointer in mt76u_get_next_rx_entry in order to add
support for new devices (e.g 7663u) that reports fw events through hw rx
mcu queue
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_process_rx_queue routine to process rx hw queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
New devices (e.g. mt7663u) do not rely on stats workqueue to load tx
statistics but will be reported by the firmware. Check tx_status_data
pointer in mt76u_tx_tasklet in order to reuse tx tasklet for new devices
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Starting from 'commit ee8040139ab1 ("mt76: do not overwrite
max_tx_fragments if it has been set")' we can avoid overwriting
max_tx_fragments for mt76x02u devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move WIPHY_FLAG_HAS_CHANNEL_SWITCH in mt76-core module since now all
drivers support Channel Switch Announcement
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce dfs radar pattern specs in mt7615 driver in order to make
dfs debugging easier. Radar pulse/pattern thresholds are taken from
vendor SDK.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce token tracing support in mt7615_mac_tx_free routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mac_txdone tracepoint in common code in order to
be reused by mt7603 and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move dev_irq tracepoint in common code in order to be reused by mt7603
and mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a set_antenna callback to setup per phy tx/rx streams.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
No need to send both MCU_EXT_CMD_SET_RX_PATH and MCU_EXT_CMD_CHANNEL_SWITCH
together to MCU.
Split them out by passing the proper command in the corresponding flow.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7615 supports dual-wiphy which means that it can run on 2.4G and 5GHz
channels simultaneously, and driver should configure each band.
Add missing register settings, and refine band related definitions to
avoid duplicate codes.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following compilation warning in mt76_eeprom_override routine
when CONFIG_OF is not set and label 'out' is not actually used
drivers/net/wireless/mediatek/mt76/eeprom.c: In function ‘mt76_eeprom_override’:
drivers/net/wireless/mediatek/mt76/eeprom.c💯1: warning: label ‘out’ defined but not used [-Wunused-label]
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on FIELD_PREP macro for led register definitions and
remove open coding
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize brightness_set and blink_set callbacks to
mt7615_led_set_brightness and mt7615_led_set_blink in order to enable
LED support in mt7615 driver
Tested-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During the cleanup of the aggregation session, a rx handler (or release timer)
on another CPU might still hold a pointer to the reorder buffer and could
attempt to release some packets.
Clearing pointers during cleanup avoids a theoretical use-after-free bug here.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before extracting the tid out of the packet, check if it was qos-data.
Only accept tid values 0-7
Also, avoid accepting the hardware queue as skb queue mapping, it could
lead to an overrun. Instead, derive the hardware queue from the tid number,
in order to avoid issues with packets being filtered multiple times.
This also fixes a mismatch between hardware and software queue indexes.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MCU_EXT_CMD_EFUSE_BUFFER_MODE needs more time on initialization, and
with only 10 seconds it sometimes runs into timeouts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We do not call mt76x02_mac_set_beacon() with NULL skb any longer and
we do not need to return error value.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With current implementation we do not cleanup beacon memory, so is not
needed to call mt76x02_mac_set_beacon() with NULL skb.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For transferring data over USB the optimal size is endpoint maxpacket.
For my hardware maxpaket for control endpoint is 64 bytes and changing
to this value from 128 bytes further shorten TBTT work time from
3ms to 1ms.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch enables channel switch support on mt76 usb interfaces.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use larger batches for usb copy to speed this operation up. Otherwise it
would be too slow for copying new beacons or broadcast frames over usb.
Assure, that always a multiple of 4 Bytes is copied, as outlined in
850e8f6fbd "mt76: round up length on mt76_wr_copy" from Felix Fietkau.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch removes a mt76_wr_copy call from the beacon path to hw.
The skb which is used in this place gets therefore build with txwi
inside its data. For mt76 usb drivers, this saves one synchronuous
copy call over usb, which lets the beacon work complete faster.
In mmio case, there is not enough headroom to put the txwi into the
skb, it is therefore using an additional mt76_wr_copy, which is fast
over mmio. Thanks Stanislaw for pointing this out.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On adding vifs the idx can become 1 + (7 & 7) = 8 for APs.
Check against that, as only AP vif idx 0-7 is possible.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sending beacons to the hardware always happens in batches. In order to
speed up beacon processing on usb devices, this patch splits out common
code an calls it only once.
Beacons are sequentially written into the beacon memory area, by
tracking its usage with the dev->beacon_data_count. For MBSS support
and buffered traffic dev->beacon_data_count is used to create the bypass
mask.
The code is also adapted for the mmio part of the driver, but should not
have any performance implication there.
MBSS tests were performed with AVM AC860 USB NIC with temporary support
for 5 BSS'. Different combinations of active vifs were created and
brought up. Afterwards connection and data transfer was tested for the
announced BSS'.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 hw does not send beacons from beacon slots, if the corresponding
bitmask is set accordingly. Therefore we can omit clearing the beacon
memory. Clearing uses many usb calls, if usb drivers are used. These
calls unnecessarily slow down the beacon tasklet. Thanks to Stanislaw
Gruzska for pointing this out.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before this patch, mt76 handled rx traffic for all TIDs equally,
when released from reorder buffer early. This patch uses an AC specific
reorder timeout, in order to release partial aggregated frames for video
ACs earlier. Voice ACs are currently not aggregated (thanks to Felix for
this hint). For example, ath10k also uses AC specific reorder timeouts
(reported by firmware in that case).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add the capability to configure acktimeout for mt7615 driver. Moreover
configure slottime according to the value provided by mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set 0 as minimum configurable value for coverage_class since mt76 does
not support dynack
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix coverage_class type in mt76x02_dev data structure since
coverage_class can be negative to enable dynack (just supported by
ath9k). Set 0 as minimum value for coverage_class
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Print fw_ver and build_date members of struct mt7615_fw_trailer
similarly to what appears in the output of 'dmesg' when the MCU firmware
is loaded.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some compilers (tested with 4.8.5 from CentOS 7) fail properly process
FIELD_GET inside an inline function, which ends up in a BUILD_BUG_ON.
Convert inline function to a macro.
Fixes commit bf92e76851 ("mt76: mt7615: add support for per-chain
signal strength reporting")
Reported in https://lkml.org/lkml/2019/9/21/146
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x0e users reported some devices (e.g TP-Link Archer VR200v) have
been flashed with big endian radio partition. Add the possibility to
specify eeprom endianness using big-endian dts property and in case
covert eeprom data in little endian
Tested-by: Kevin Schmidt <kevin.patrick.schmidt@googlemail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reset MT_MIB_STAT_CCA after channel switch since it is used to track busy
time starting from 'commit dcff8d4dc3 ("mt76: mt7603: switch to a
different counter for survey busy time")'
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure the MAC address is checked before function returns.
If CONFIG_OF is set and the device node is null, the function will
return directly, and an invalid MAC address will not be checked.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To avoid having the hardware potentially write to memory behind stale
descriptors, set the dma-done flag on all of them before cleaning up
allocated rx buffers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MT7615 firmware needs to know the association id at creation time,
which is unavailable during the transition from notexist to none in
.sta_state.
This can cause a number of issues, probably also breaking powersave
support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Loading the mcu firmware and waiting for it to boot takes a long time,
which adds a significant amount to the system boot time.
Fix this by running the mcu init from a workqueue and waiting for it to
complete before starting the phy or issuing mcu commands via debugfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is only used for testing for now. In the future it will be possible to
enable the second PHY through an proper API via device tree
Running:
echo 1 > /sys/kernel/debug/ieee80211/phyX/mt76/dbdc
will register a second wiphy (and limit the primary one to 2 spatial streams).
The second wiphy will only be able to run on 5 GHz, while the primary one can
operate in both bands (if supported by the device).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Beacons and management frames need to explicitly select the alternate tx
queues in order to be sent out on the right phy
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Program the RMAC CHFREQ registers to properly indicate the band that the
frames are received on.
Add some sanity checks to the programmed values, because the firmware
programs these registers differently
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move chainmask to struct mt7615_phy and instead of needlessly making the
format similar to values for older chips, make it refer to the actual chain
bits used for the rx/tx path.
This is important for multiple wiphy support, where for a secondary phy,
antenna_mask will start at 0, and chainmask will start at the chain offset
(bit 2)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are two DFS detectors on the chip. When using 160 MHz channel bandwidth
(not supported in dual-wiphy mode), both are used. Otherwise, one detector is
used per wiphy.
Rework the code to start/stop them separately per phy and to indicate the
radar event on the right phy based on the detector index
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Prevent the overwriting of max_tx_fragments if it has already been set
in chip-specific init routine.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for an extra wiphy in mt76_set_channel and mt76_get_survey
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is preparation for supporting multiple wiphys per device to support the
concurrent dual-band feature of MT7615D
On the first wiphy, hw->priv will point to struct mt76_dev, which contains a
struct mt76_phy at the start. For the secondary wiphy, hw->priv will point
to a mt76_phy encapsulated in a driver specific struct
To simplify access to struct mt76_phy members from drivers, the driver specific
device struct is changed to add a union of struct mt76_dev and struct mt76_phy
as the first element
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In associating and configuring beamformee, bfee->role is not
correctly set before rtw_chip_ops::config_bfee().
Fix it by setting it correctly.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The logic for checking required NVM sections was recently fixed in
commit b3f20e0982 ("iwlwifi: mvm: fix NVM check for 3168
devices"). However, with that fixed the else is now taken for 3168
devices and within the else clause there is a mandatory check for the
PHY_SKU section. This causes the parsing to fail for 3168 devices.
The PHY_SKU section is really only mandatory for the IWL_NVM_EXT
layout (the phy_sku parameter of iwl_parse_nvm_data is only used when
the NVM type is IWL_NVM_EXT). So this changes the PHY_SKU section
check so that it's only mandatory for IWL_NVM_EXT.
Fixes: b3f20e0982 ("iwlwifi: mvm: fix NVM check for 3168 devices")
Signed-off-by: Dan Moulding <dmoulding@me.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some tests shows that using AMSDU to aggregate TCP ACKs to specific
APs will degrade the throughput on 2.4G band in 20MHz bandwidth
(< 10 Mbps, should be ~100 Mbps for 2x2). Also found that there's
barely no negative impact if we disable TX AMSDU on 2.4G to connect
to other APs. So it seems like we can just tell mac80211 to not to
aggregate MSDUs when transmitting on 2.4G band.
Note that we still can TX AMSDU on 5G band and benefit from it by
having 50 ~ 70 Mbps throughput improvement.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
According to some experiments, the original RF register protection
setting of 8822c cannot perfectly make sure that there is no hardware
PI write (direct) during direct write. Modify the setting so that the
hardware block of PI would be turned off via rtw8822c_rstb_3wire()
during the direct write, to avoid RF register racing.
Note that 8822b uses SIPI write (indirect), so 8822b does not
have such problem.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware value of secondary channel offset isn't very intuitive. This
commit adds enumeration, so we can easier to check the logic with the
suffix of enumeration name, likes _UPPER or _LOWER.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sk_buff structs need to be freed with kfree_skb(), not kfree().
Fixes: b6c12908a3 ("rtw88: Add wowlan net-detect support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Appearently the hw pointer can be NULL while the module is loaded and
in that case rsi_shutdown() crashes due to the unconditional dereference.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Though hardware isn't implement CCMP-256, GCMP and GCMP-256, it's possible
to fallback to use software de-/en-cryption implemented by mac80211.
Without adding these chipers, kernel log will show something if we connect
to a WPA3 enterprise AP, likes
wlan0: failed to set key (1, ff:ff:ff:ff:ff:ff) to hardware (-524)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver could possibly be dead-locked while canceling works with
*_sync() with mutex lock held. Those cancel_delayed_work_sync()
functions will wait until the work is done, but if we hold the
lock, they will never acquire the lock.
To prevent this, simply release the lock and acquire again after
the works have been canceled. And to avoid the works being queued
again, check if the device is at RTW_FLAG_RUNNING state, otherwise
just return and do nothing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver is coming up, mac80211 will set changed as ~0 (0xffffffff),
and driver could enter IDLE state (power off) before switching channel or
other config event. So move rtw_enter_ips() to the last, to make sure the
driver completed the config events before going to IDLE state.
So, moves leave/enter IPS config to be first/last one according to flag
IEEE80211_CONF_IDLE. If there're more configureations we want to add in
the future, they must locate between leave/enter IPS.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since RTL8822CE has enabled reference clock auto calibration,
there is no need to add any clock delay for covering the timing
gap of the reference clock.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
vif is not used, remove it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With commit 216b44000a ("brcmfmac: Fix use after free in
brcmf_sdio_readframes()") applied, we see locking timeouts in
brcmf_sdio_watchdog_thread().
brcmfmac: brcmf_escan_timeout: timer expired
INFO: task brcmf_wdog/mmc1:621 blocked for more than 120 seconds.
Not tainted 4.19.94-07984-g24ff99a0f713 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
brcmf_wdog/mmc1 D 0 621 2 0x00000000 last_sleep: 2440793077. last_runnable: 2440766827
[<c0aa1e60>] (__schedule) from [<c0aa2100>] (schedule+0x98/0xc4)
[<c0aa2100>] (schedule) from [<c0853830>] (__mmc_claim_host+0x154/0x274)
[<c0853830>] (__mmc_claim_host) from [<bf10c5b8>] (brcmf_sdio_watchdog_thread+0x1b0/0x1f8 [brcmfmac])
[<bf10c5b8>] (brcmf_sdio_watchdog_thread [brcmfmac]) from [<c02570b8>] (kthread+0x178/0x180)
In addition to restarting or exiting the loop, it is also necessary to
abort the command and to release the host.
Fixes: 216b44000a ("brcmfmac: Fix use after free in brcmf_sdio_readframes()")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: franky.lin@broadcom.com
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most part of scan command data is always present, so no need
to keep it in TLV. Simplify scan command processing moving
most part of its parameters into a fixed part of
qlink_cmd_scan message.
Use fixed dwell time values for normal scan when device is not
connected, and allow wireless card decide on dwell times by
itself if it's operating as a STA and is connected. When
connected, card can select dwell times dynamically based on
traffic conditions to get best results.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With an addition of 6GHz band support, channel number can no longer be
used to uniquely identify a specific channel. Modify channel switch
command to use chandef data.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that all elements in QLINK protocol message are aligned to
4 bytes. For this purpose add necessary amount of padding bytes to
each message. Besides, add padding for non-aligned variable length
fields, e.g. SSID, so that the first byte of the next variable length
element is aligned. to 4 bytes. Finally, introduce TLV parsing helpers
to reduce boilerplate TLV parsing code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each radio on a given wifi device may have different max scan SSIDs
limitation, so take this information from a per-radio info structure.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switch to extendable implementation of channel survey dump to make sure
that any new channel statistics can be added in the future without any
backwards compatibility issues. For this purpose use a separate variable
length bitmap to pass the list of valid statistics in firmware response.
Besides, switch to using channel frequency instead of IEEE channel
number to prepare for adding support of 6GHz band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Information about interface combinations is now available in a fixed
portion of struct qlink_resp_get_mac_info. Use that information to
get interface combinations. TLV type QTN_TLV_ID_NUM_IFACE_COMB is
not needed anymore and can be dropped.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
