PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
v2: Mika pointed out that 24 was hardcoded while it
should consider ref clock that can be either 24KHz
or 19.2KHz on CNL.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499374321-31152-1-git-send-email-rodrigo.vivi@intel.com
The Cursor Coeff is lower 6 bits in the PORT_TX_DW4 register
and hence the CURSOR_COEFF_MASK should be (0x3F << 0)
Fixes: 04416108cc ("drm/i915/cnl: Add registers related to voltage
swing sequences.")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498785241-21138-1-git-send-email-manasi.d.navare@intel.com
Paulo noticed that we were missing few bits clear
before writing values back to the register on
these RMW MMIO operations.
v2: Remove "POST_" from CURSOR_COEFF_MASK. (Paulo).
v3: Remove unnecessary braces. (Jani).
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497897572-22520-1-git-send-email-rodrigo.vivi@intel.com
Enables access to OA unit metrics for BDW, CHV, SKL and BXT which all
share (more-or-less) the same OA unit design.
Of particular note in comparison to Haswell: some OA unit HW config
state has become per-context state and as a consequence it is somewhat
more complicated to manage synchronous state changes from the cpu while
there's no guarantee of what context (if any) is currently actively
running on the gpu.
The periodic sampling frequency which can be particularly useful for
system-wide analysis (as opposed to command stream synchronised
MI_REPORT_PERF_COUNT commands) is perhaps the most surprising state to
have become per-context save and restored (while the OABUFFER
destination is still a shared, system-wide resource).
This support for gen8+ takes care to consider a number of timing
challenges involved in synchronously updating per-context state
primarily by programming all config state from the cpu and updating all
current and saved contexts synchronously while the OA unit is still
disabled.
The driver intentionally avoids depending on command streamer
programming to update OA state considering the lack of synchronization
between the automatic loading of OACTXCONTROL state (that includes the
periodic sampling state and enable state) on context restore and the
parsing of any general purpose BB the driver can control. I.e. this
implementation is careful to avoid the possibility of a context restore
temporarily enabling any out-of-date periodic sampling state. In
addition to the risk of transiently-out-of-date state being loaded
automatically; there are also internal HW latencies involved in the
loading of MUX configurations which would be difficult to account for
from the command streamer (and we only want to enable the unit when once
the MUX configuration is complete).
Since the Gen8+ OA unit design no longer supports clock gating the unit
off for a single given context (which effectively stopped any progress
of counters while any other context was running) and instead supports
tagging OA reports with a context ID for filtering on the CPU, it means
we can no longer hide the system-wide progress of counters from a
non-privileged application only interested in metrics for its own
context. Although we could theoretically try and subtract the progress
of other contexts before forwarding reports via read() we aren't in a
position to filter reports captured via MI_REPORT_PERF_COUNT commands.
As a result, for Gen8+, we always require the
dev.i915.perf_stream_paranoid to be unset for any access to OA metrics
if not root.
v5: Drain submitted requests when enabling metric set to ensure no
lite-restore erases the context image we just updated (Lionel)
v6: In addition to drain, switch to kernel context & update all
context in place (Chris)
v7: Add missing mutex_unlock() if switching to kernel context fails
(Matthew)
v8: Simplify OA period/flex-eu-counters programming by using the
batchbuffer instead of modifying ctx-image (Lionel)
v9: Back to updating the context image (due to erroneous testing,
batchbuffer programming the OA unit doesn't actually work)
(Lionel)
Pin context before updating context image (Chris)
Drop MMIO programming now that we switch to a kernel context with
right values in initial context image (Chris)
v10: Just pin_map the contexts we want to modify or let the
configuration happen on first use (Chris)
v11: Update kernel context OA config through the batchbuffer rather
than on the fly ctx-image update (Lionel)
v12: Rework OA context registers update again by swithing away from
user contexts and reconfiguring the kernel context through the
batchbuffer and updating all the other contexts' context image.
Also take care to lock slice/subslice configuration when OA is
on. (Lionel)
v13: Request rpcs updates on all engine when updating the OA config
(Lionel)
v14: Drop any kind of rpcs management now that we monitor sseu
configuration changes in a later patch (Lionel)
Remove usleep after programming the NOA configs on Gen8+, this
doesn't seem to be needed (Lionel)
v15: Respect coding style for block comments (Chris)
v16: Add missing i915_add_request() in case we fail to emit OA
configuration (Matthew)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com> \o/
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.
v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com
This are the registers and bits needed for the voltage swing
sequence on Cannonlake.
v2: Remove CL_DW5 that was wrongly defined.
v3: Use (1 << 1) instead of (1<<1) as Paulo suggested
Change DW2 swing sel upper and lower macros to do the
bit selection instead of definint a table that doesn't
match the spec. It is based on a Manasi version of it.
Credits-to: Manasi.
v4: Let SCALING_MODE_SEL flexible. (Manasi)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-9-git-send-email-rodrigo.vivi@intel.com
Also new registers can have different mmio offsets
per different lane per port.
v2: Use _PICK as PORT3 instead of creating a new
macro with if per port.
v3: Use _PICK directly on MMIO_PORT6. While MMIO_PORT
isn't flexible enough let's continue with MMIO_PORT6
as we have MMIO_PORT3.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-8-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Although CNL follows PLL initialization more like Skylake
than Broxton we have a completely different initialization
sequence and registers used.
One big difference from SKL is that CDCLK PLL is now
exclusive (ADPLL) and for DDIs and MIPI we need to use
DFGPLLs 0, 1 or 2.
v2: Accept all Ander's suggestions and fixes:
- Registers and bits names prefix
- Group pll functions
- bits masks fixes
- remove read and modify on cfgcr1
- fix cfgcr0 setup
v3: Set SSC_ENABLE for DP.
Fix HDMI_MODE cfgcr0.
Avoid touch cfgcr0 on DP.
Add missed else on dpll_mgr definition so we use cnl one, not hsw.
v3: Centra freq should be always set to default and change bits
definitions to (1 << 1) instead of (1<<1). (by Paulo)
v4: Rebased.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-7-git-send-email-rodrigo.vivi@intel.com
One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.
So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.
v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
so we were disabling interrupts.
Credits-to: Clinton
Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
and clock on in 2 separated reg writes. (Paulo)
Also update bits definitions to use space
(1 << 1) instead of (1<<1). (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com
Implement the CNL display init/uninit sequence as outlined in Bspec.
Quite similar to SKL/BXT. The main complicaiton is probably the extra
procmon setup we must do based on the process/voltage information we
can read out from some register.
v2: s/skl_dbuf/gen9_dbuf/ to follow upstream
bxt needed a cdclk sanitize step, so let's add it for cnl too
v3: s/CHICKEN_MISC_1/CHICKEN_MISC_2/ (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework
v5: Removed unecessary Aux IO forced enable/disable, Fix DW10 setup
Fix procpon Mask. (Credits-to Paulo and Clint)
Remove A0 workaround.
v6: Rebased on top of recent code (Rodrigo).
v7: Respect the order of sanitize_ after set_
(Done by Rodrigo, Requested by Ville)
v8: Commit message updated to matvh v5 changes besides
Remove unused DW8 and an extra blank line. (all noticed
by Imre).
v9: Remove __attribute__((unused)) added on latest version
of drm/i915/cnl: Implement .set_cdclk() for CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-3-git-send-email-rodrigo.vivi@intel.com
Add support for reading out the cdclk frequency from the hardware on
CNL. Very similar to BXT, with a few new twists and turns:
* the PLL is now called CDCLK PLL, not DE PLL
* reference clock can be 24 MHz in addition to the 19.2 MHz BXT had
* the ratio now lives in the PLL enable register
* Only 1x and 2x CD2X dividers are supported
v2: Deal with PLL lock bit the same way as BXT/SKL do now
v3: DSSM refclk indicator is bit 31 not 24 (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework.
v5: Set cdclk to the ref clock as previous platforms. (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-1-git-send-email-rodrigo.vivi@intel.com
Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com
CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.
Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.
v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
for the same reasons as v4 when we found out that current CNL
SKUs don't have the full port E split.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com
The number of compressed segments has been available ever since
FBC2 was introduced in g4x, it just moved from the STATUS register
into STATUS2 on IVB.
For FBC1 if we really wanted the number of compressed segments we'd
have to trawl through the tags, but in this case since the code just
uses the number of compressed segments as an indicator whether
compression has occurred we can just check the state of the
COMPRESSING and COMPRESSED bits. IIRC the hardware will try to
periodically recompress all uncompressed lines even if they haven't
changed and the COMPRESSED bit will be cleared while the compressor
is running, so just checking the COMPRESSED bit might not give us
the right answer. Hence it seems better to check for both
COMPRESSED and COMPRESSING as that should tell us that the
compressor is at least trying to do something.
While at it move the IVB+ register define to the right place, unify
the naming convention of the compressed segment count masks, and
fix up the mask for g4x.
v2: s/ILK_DPFC_STATUS2/IVB_FBC_STATUS2/ (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk> # SNB
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # ilk+
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # pre-ilk
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124318.31755-1-ville.syrjala@linux.intel.com
On CNP PCH based platforms the gmbus is on the south display that
is on PCH. The existing implementation for previous platforms
already covers the need for CNP expect for the pin pair configuration
that follows similar definitions that we had on BXT.
v2: Don't drop "_BXT" as the indicator of the first platform
supporting this pin numbers. Suggested by Daniel.
v3: Add missing else and fix register table since CNP GPIO_CTL
starts on 0xC5014.
v4: Fix pin number and map according to the current available VBT.
Re-add pin 4 for port D. Lost during some rebase.
v5: Use table as spec. If VBT is wrong it should be ignored.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-5-git-send-email-rodrigo.vivi@intel.com
RAWCLK_FREQ register has changed for platforms with CNP+.
[29:26] This field provides the denominator for the fractional
part of the microsecond counter divider. The numerator
is fixed at 1. Program this field to the denominator of
the fractional portion of reference frequency minus one.
If the fraction is 0, program to 0.
0100b = Fraction .2 MHz = Fraction 1/5.
0000b = Fraction .0 MHz.
[25:16] This field provides the integer part of the microsecond
counter divider. Program this field to the integer portion
of the reference frequenct minus one.
Also this register tells us that proper raw clock should be read
from SFUSE_STRAP and programmed to this register. Up to this point
on other platforms we are reading instead of programming it so
probably relying on whatever BIOS had configured here.
Now on let's follow the spec and also program this register
fetching the right value from SFUSE_STRAP as Spec tells us to do.
v2: Read from SFUSE_STRAP and Program RAWCLK_FREQ instead of
reading the value relying someone else will program that
for us.
v3: Add missing else. (Jani)
v4: Addressing all Ville's catches:
Use macro for shift bits instead of defining shift.
Remove shift from the cleaning bits with mask that already
has it.
Add missing I915_WRITE to actually write the reg.
Stop using useless DIV_ROUND_* on divider that is exact
dividion and use DIV_ROUND_CLOSEST for the fraction part.
v5: Remove useless Read-Modify-Write on raclk_freq reg. (Ville).
v6: Change is per PCH instead of per platform.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-3-git-send-email-rodrigo.vivi@intel.com
This is a follow-up patch to the previous patch ([PATCH[1/2] drm/i915:
Disable decoupled MMIO) to remove the dead code for decoupled MMIO
implementation, as it won't be used any longer on GEN9LP.
Therefore, this patch reverts:
commit 85ee17ebee
Author: Praveen Paneri <praveen.paneri@intel.com>
Date: Tue Nov 15 22:49:20 2016 +0530
drm/i915/bxt: Broxton decoupled MMIO
Signed-off-by: Kai Chen <kai.chen@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-3-kai.chen@intel.com
This commit fixes the following compiler warning:
drivers/gpu/drm/i915/intel_dsi.c: In function ‘intel_dsi_prepare’:
drivers/gpu/drm/i915/intel_dsi.c:1487:23: warning:
?: using integer constants in boolean context [-Wint-in-bool-context]
PORT_A ? PORT_C : PORT_A),
Fixes: f4c3a88e5f ("drm/i915: Tighten mmio arrays for MIPI_PORT")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518110644.9902-1-hdegoede@redhat.com
IVB introduced the CUR_FBC_CTL register which allows reducing the cursor
height down to 8 lines from the otherwise square cursor dimensions.
Implement support for it. CUR_FBC_CTL can't be used when the cursor
is rotated.
Commandeer the otherwise unused cursor->cursor.size to track the
current value of CUR_FBC_CTL to optimize away redundant CUR_FBC_CTL
writes, and to notice when we need to arm the update via CURBASE if
just CUR_FBC_CTL changes.
v2: Reverse the gen check to make it sane
v3: Only enable CUR_FBC_CTL when cursor is enabled, adapt to
earlier code changes which means we now actually turn off
the cursor when we're supposed to unlike v2
v4: Add a comment about rotation vs. CUR_FBC_CTL,
rebase due to 'dirty' (Chris)
v5: Rebase to the atomic world
Handle 180 degree rotation
Add HAS_CUR_FBC()
v6: Rebase
v7: Rebase due to I915_WRITE_FW/uncore.lock
s/size/fbc_ctl/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Turns out our skills in decoding the CLKCFG register weren't good
enough. On this particular elk the answer we got was 400 MHz when
in reality the clock was running at 266 MHz, which then caused us
to program a bogus AUX clock divider that caused all AUX communication
to fail.
Sadly the docs are now in bit heaven, so the fix will have to be based
on empirical evidence. Using another elk machine I was able to frob
the FSB frequency from the BIOS and see how it affects the CLKCFG
register. The machine seesm to use a frequency of 266 MHz by default,
and fortunately it still boot even with the 50% CPU overclock that
we get when we bump the FSB up to 400 MHz.
It turns out the actual FSB frequency and the register have no real
link whatsoever. The register value is based on some straps or something,
but fortunately those too can be configured from the BIOS on this board,
although it doesn't seem to respect the settings 100%. In the end I was
able to derive the following relationship:
BIOS FSB / strap | CLKCFG
-------------------------
200 | 0x2
266 | 0x0
333 | 0x4
400 | 0x4
So only the 200 and 400 MHz cases actually match how we're currently
decoding that register. But as the comment next to some of the defines
says, we have been just guessing anyway.
So let's fix things up so that at least the 266 MHz case will work
correctly as that is actually the setting used by both the buggy
machine and my test machine.
The fact that 333 and 400 MHz BIOS settings result in the same register
value is a little disappointing, as that means we can't tell them apart.
However, according to the gmch datasheet for both elk and ctg 400 Mhz is
not even a supported FSB frequency, so I'm going to make the assumption
that we should decode it as 333 MHz instead.
Cc: stable@vger.kernel.org
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100926
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504181530.6908-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Pre-calculate engine context size based on engine class and device
generation and store it in the engine instance.
v2:
- Squash and get rid of hw_context_size (Chris)
v3:
- Move after MMIO init for probing on Gen7 and 8 (Chris)
- Retained rounding (Tvrtko)
v4:
- Rebase for deferred legacy context allocation
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
In such a way that vcs and vcs2 are just two different instances (0 and 1)
of the same engine class (VIDEO_DECODE_CLASS).
v2: Align the instance types (Tvrtko)
v3: Don't use enums for bspec-defined stuff (Michal)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491834873-9345-2-git-send-email-oscar.mateo@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
We have used cz timestamp register to gain a reference time wrt
to residency calculations. The residency counts are in cz clk ticks
(333Mhz clock) but for some reason the cz timestamp register gives
100us units. Perhaps for some other usage, the base-ten based values
are easier, but in residency calculations raw units would have been
the easiest.
As there is not much advantage of using base-ten clock through
a more costly punit access, take our reference times directly from
kernel clock.
v2: use ktime (Chris, Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The REDIRECT_TO_GUC bit is a strange beast as it is a disable bit -
setting the bit in the pm interrupt generation stops the interrupt going
to the guc (not sending it to the guc as the name implies). To help the
reader rename it to DISABLE_REDIRECT_TO_GUC so that we keep the bspec
greppable name without it being as confusing!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312132745.9618-1-chris@chris-wilson.co.uk
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Driver needs to ensure that it doesn't mask the PM interrupts, which are
unmasked/needed by GuC firmware. For that, Driver maintains a bitmask of
interrupts to be kept unmasked, pm_intr_keep.
pm_intr_keep was determined across GuC load. GuC gets loaded in different
scenarios and it is not going to change the pm_intr_keep so this patch
moves its setup to intel_irq_init.
This patch fixes incorrect RPS masking leading to UP interrupts triggered
even when at cur_freq=max and inversly for Down interrupts.
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488862355-9768-1-git-send-email-sagar.a.kamble@intel.com
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
Generally we are using macros for any hardware identifiers as these
may change between Gens. Do the same with hardware engine ids.
v2: move hw engine defs to i915_reg.h (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301202615.118632-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drivers/gpu/drm/i915/intel_dsi.c: In function ‘intel_dsi_prepare’:
drivers/gpu/drm/i915/intel_dsi.c:1308:1: error: the frame size of 2488 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
which is caused by the compiling expanding every _MIPI_PORT into an
on-stack array of u32[3] at every callsite. Not sure why only one
machine/compiler appears susceptible, but with a minor tweak to _MIPI_PORT
we can defer the error until later.
This is a partial revert of commit ce64645d86 ("drm/i915: use variadic
macros and arrays to choose port/pipe based registers") for a particular
bad offender.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228145519.18012-1-chris@chris-wilson.co.uk
Acked-by: Jani Nikula <jani.nikula@intel.com>
v2: Addressed Jani's Review comments(renamed bit field macros)
Txesc clock divider is calculated and programmed
for geminilake platform.
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-7-git-send-email-madhav.chauhan@intel.com
PLL divider range for GLK is different than that of
BXT, hence adding the GLK range check in this patch.
v2: Code restructure using min and max ratio variables (Ander)
v3: Code changes to avoid "maybe-uninitialized" warning (Jani)
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-5-git-send-email-madhav.chauhan@intel.com
Program the clk lane and tlpx time count registers
to configure DSI PHY.
v2: Addressed Jani's Review comments(renamed bit field macros)
v3: Program clk lane timing reg same as dphy param reg.
v4: Removed "line over 80 character" warning
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-3-git-send-email-madhav.chauhan@intel.com
-----BEGIN PGP SIGNATURE-----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=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Following a reset, the context and page directory registers are lost.
However, the queue of requests that we resubmit after the reset may
depend upon them - the registers are restored from a context image, but
that restore may be inhibited and may simply be absent from the request
if it was in the middle of a sequence using the same context. If we
prime the CCID/PD registers with the first request in the queue (even
for the hung request), we prevent invalid memory access for the
following requests (and continually hung engines).
v2: Magic BIT(8), reserved for future use but still appears unused.
v3: Some commentary on handling innocent vs guilty requests
v4: Add a wait for PD_BASE fetch. The reload appears to be instant on my
Ivybridge, but this bit probably exists for a reason.
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207152437.4252-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit c0dcb203fb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Once the address space has been created (using 3 or 4 levels of page
tables), we should use that to program the appropriate type into the
contexts. This gives us the flexibility to handle different types of
address spaces at runtime.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170209144036.23664-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Following a reset, the context and page directory registers are lost.
However, the queue of requests that we resubmit after the reset may
depend upon them - the registers are restored from a context image, but
that restore may be inhibited and may simply be absent from the request
if it was in the middle of a sequence using the same context. If we
prime the CCID/PD registers with the first request in the queue (even
for the hung request), we prevent invalid memory access for the
following requests (and continually hung engines).
v2: Magic BIT(8), reserved for future use but still appears unused.
v3: Some commentary on handling innocent vs guilty requests
v4: Add a wait for PD_BASE fetch. The reload appears to be instant on my
Ivybridge, but this bit probably exists for a reason.
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207152437.4252-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
The audio chicken bit (register offset 0x62f38) seems required to make
DP audio working on some machines. At least, on Dell Wyse 3040, I
failed to get the audio unless this bit is set once.
Strangely, the bit seems necessary only once, and it persists after
that, even some power-off cycles. The register is supposedly
write-only, so it's no evidence whether the bit keeps effect
persistently. But, judging from the experiment, it looks enough to
set it up once at the device initialization.
The patch is basically a cut from the original patch by Pierre-Louis
Bossart.
v1->v2: drop read since it's a write-only reg.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable unmute/mute amp notification. This doesn't seem to affect
HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38
prior to the mute/unmute but this register doesn't seem to do anything
so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable.
v2->v3: Add "_" prefix to VLV_AUD_PORT_EN_X_DBG as they are internal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable MIPI IO WA for BXT DSI as per bspec and
program the DSI regulators.
v2: Moved IO enable to pre-enable as per Mika's
review comments. Also reused the existing register
definition for BXT_P_CR_GT_DISP_PWRON.
v3: Added Programming the DSI regulators as per disable/enable
sequences.
v4: Restricting regulator changes to BXT as suggested by
Jani/Mika
v5: Removed redundant read/modify for regulator register as
per Jani's comment. Maintain enable/disable symmetry as per spec.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Acked-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485353603-11260-1-git-send-email-vidya.srinivas@intel.com
This allows the use of more than 3 ports/pipes/whatever without tricks,
even if the register offsets are not evenly spaced.
There's the risk of out of bounds access if we're not careful; currently
that would "just" lead to the wrong register offset being used. It might
be possible to add build bug ons for build time constant indexing.
We already have ports defined up to E, not sure if we might have bugs
related to them and the current _PORT3() macro.
text data bss dec hex filename
1239868 46199 4096 1290163 13afb3 drivers/gpu/drm/i915/i915.ko
1238828 46199 4096 1289123 13aba3 drivers/gpu/drm/i915/i915.ko
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485532626-20923-1-git-send-email-jani.nikula@intel.com
Move the invariant parts of context desc setup from execlist init
to context creation. This is advantageous when we need to
create different templates based on the context parametrization,
ie. for svm capable contexts.
v2: s/create/default, remove engine->ctx_desc_template
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485522189-31984-1-git-send-email-mika.kuoppala@intel.com
The gamma tables in Geminilake were changed. There is no split-gamma
mode. Instead, there is a dedicated degamma table that is enabled
whenever pipe CSC is enabled.
The dedicated gamma table has 16 bit precision but doesn't support
separate channels. Since that doesn't match the per-channel format of
the degamma LUT property, for now only a linear table is loaded and the
property ignored.
v2: Remove empty line. (Ville)
Reuse broadwell code. (Ville)
v3: Don't write PIPE_CSC_MODE. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127090230.20302-1-ander.conselvan.de.oliveira@intel.com
In Geminilake, the bits for enabling pipe csc, pipe gamma and plane
gamma moved to a new register. So update the plane update functions
to set the right bits.
Pipe CSC is kept disabled though, since enabling that also enables the
dedicated degamma table, and that is not properly programmed yet,
leading to a black screen.
v2: Use plane_id. (Ville)
Remove unnecessary variable. (Ville)
Keep registers in offset order. (Ville)
Don't set plane gamma disable twice. (Ander)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485429865-10687-3-git-send-email-ander.conselvan.de.oliveira@intel.com
Enable support for HDMI LPE audio mode on Baytrail and
Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load:
1. Create a platform device to share MMIO/IRQ resources
2. Make the platform device child of i915 device for runtime PM.
3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the
LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reports live state of PSR2 form PSR2_STATUS register.
bit field 31:28 gives the live state of PSR2.
It can be used to check if system is in deep sleep,
selective update or selective update standby.
During video play back, we can use this to check
if system is entering SU mode or not.
when system is in idle state, DEEP_SLEEP(8) must be entered.
When video playback is happening, system must be in
SLEEP(3 / selective update) or SU_STANDBY( 6 / selective update standby)
v2: (Rodrigo)
- Remove EDP_PSR2_STATUS_TG_ON=a ,instead use ARRAY_SIZE
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483720352-24761-1-git-send-email-vathsala.nagaraju@intel.com
