The container node in the iomuxc node is no longer necessary and causes
pinctl errors on the Ventana boards with analog video capture
since aa12693e41:
pinctrl core: initialized pinctrl subsystem
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/adv7180grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/ipu2_csi1grp
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table
imx6q-pinctrl 20e0000.iomuxc: function 'iomuxc' not supported
imx6q-pinctrl 20e0000.iomuxc: invalid function iomuxc in map table
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All of the Gateworks Ventana boards based on the IMX6 SoC except for the
GW54xx use the LTC3676 PMIC. Add a device-tree node with interrupt support
for this PMIC. Additionally remove the simple-bus notation in the regulator
nodes and any fixed regulators that are provided by the PMIC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
bc677ff42e adds a device-tree property
to specify that an external watchdog reset is used to reset other
portions of the board and not just the IMX6 SoC.
This adds the property to the proper watchdog as well as the pinmux for
the Gateworks Ventana boards that use this external watchdog reset to
reset the PMIC which will reset all the PMIC power rails and not just
a chip-level IMX6 reset. This helps to work around various system issues
that can cause a hang when coming out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ventana boards have an off-board connector with signals that can be pinmuxed
as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled
state which the bootloader can decide to enable based on bootloader config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. To support this pinctl states for 100Mhz and 200MHz
must be added as well as pinmux of the VSELECT signal. In order to support
UHS-I the I/O rail of the 4-bit data bus must be switchable between 1.8V
and 3.3V.
By adding the no-1-8-v property, which disables UHS-I support, we allow the
bootloader to be in charge of selecting which boards have this capability
by removing that property if the board model/revision implement the support.
Additionally we will remove NANDF_CS1 here from the nand pinmux group as the
second chip-select is not used on any ventana boards and this is the pad
that is used for SD3_VELECT.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Follow the conventions for pinctrl:
- grouping pinctrl in logical alphabatized groups
- remove any pinctrl not being used by a driver or needed by user
- move iomuxc to bottom of file for readability
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Follow the convention of configuring padconf for all pins and not leaving
any 0x80000000 to leave them un-configured.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Use the gpio contants defined in bindings for active high/low
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Remove aliases that are either not used by bootloader or are provided via
included dtsi files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The general device-tree rule is to not include nodes that do not have a driver
or bindings in a dts/dtsi. Remove the place-holder nodes from the Gateworks
Ventana boards until a time that a driver with proper bindings exists.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The vendor prefix for Linear Technology should be lltc,
same as the NASDAQ symbol.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The Gateworks Ventana product family consists of several baseboard designs
based on the Freescale i.MX6 family of processors. Each baseboard has a
different set of possible features.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
