It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the imx pci driver fails to probe on i.MX6SX.
Fix the PCI representation so that the driver can be probed and
PCI devices can be detected.
Tested on a im6sx-sdb board:
00:00.0 Class 0604: 16c3:abcd
01:00.0 Class 0280: 8086:08b1
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.
This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit a22950c888 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1021a esdhc had been enabled in uboot,
but it had not been enabled it in kernel,
So set the esdhc's status to "okay".
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two Ethernet switches have an AT24C512 each. This is a 64K device,
not 512 bytes as currently listed in the device tree.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in i.MX dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames the audio device to "Front" in order to match the RDU2
naming, which makes it easier for a unified userspace to deal with
both boards.
Also rename the phandle for the headphone amplifier to more closely
resemble the RDU2 DTS.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are 0 ohm resistors that allow selecting the EDID I2C port to
be I2C1 or I2C2.
On revd1 the 0 ohm resistors are populated in such a way that the I2C2
is used as DDC I2C bus, so fix it accordingly.
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7s/imx7d has the ptp interrupt newly added as well.
For imx7, "int0" is the interrupt for queue 0 and ENET_MII
"int1" is for queue 1
"int2" is for queue 2
For imx6sx, "int0" handles all 3 queues and ENET_MII
And of course, the "pps" interrupt is for the PTP_CLOCK_PPS interrupts
This will help document what each interrupt does.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is needed for the bootloader to patch in the correct MAC address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warning is seen with W=1:
Warning (unit_address_vs_reg): Node /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has a unit name, but no reg property
Fix this warning by adding reg property from such node and, consequently,
includes a mdio node into the fec node, with the 'address-cells' and
'size-cells' to avoid these other following warnings:
Warning (reg_format): "reg" property in /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Tested-by: Lothar Waßmann <LW@karo-electronics.de>
Acked-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add QSPI node support, and this function is disabled by default
This setting could be overwritten in board-level definitions
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
-----BEGIN PGP SIGNATURE-----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=xHta
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: fix UART pclk clock name
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>
These recently started showing up with better dtc checks being
introduced.
-----BEGIN PGP SIGNATURE-----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=BHn4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two fixes for dts compiler warnings
These recently started showing up with better dtc checks being
introduced.
* tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dm814x missing phy-cells property
ARM: dts: Fix elm interrupt compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in nspire dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have phy-cells for usb_phy0, but it's missing for usb_phy1 and we get:
Warning (phys_property): Missing property '#phy-cells' in node
/ocp/l4ls@48000000/control@140000/usb-phy@1b00 or bad phandle
(referred from /ocp/usb@47400000/usb@47401800:phys[0])
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the interrupt property is missing the controller and level
information causing:
Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes for omaps for v4.15-rc cycle with two fixes for hangs with the
rest being compiler warning fixes and fixes for power states and devices
on various boards:
- Fix smatch issue introduced by recent omap device changes for legacy
resources
- Fix SRAM virt to phys related boot hang affecting n900 and other omap3 hs
devices found by pending CMA changes. While it seems that we have not hit
this in other use cases, let's fix it to avoid a nasty and hard to find
suprise as right now there is just luck keeping the SRAM virtual address
to physical address translation working with the 0xffff high_mask.
- Fix am335x reading of domain state registers that only exist for the
PM_CEFUSE domain and produce wrong results for other domains
- Fix missing setting for error code for omap device if allocation fails
- Fix missing modules_offs for omap3 MMC3 affecting n9/n950
- Fix cm_split_idlest() reading reserved registers showing wrong
idlestatus
- Fixes to correct #phy-cells property for compiler warnings that
recently started happening
- Add a missing OHCI remote-wakeup-connected property that I was supposed
to merge after the ohci-omap3 to ohci-platform changes but somehow managed
to drop. I only noticed this was missing while debugging the OHCI/EHCI GPS
and modem hang
- Fix a system hang with GPS or modem connected to the OHCI/EHCI bus that
typically happened within 20 - 40 minutes on an idle system. This turned
out to be an issue caused by using the parent interrupt controller directly
with the WUGEN + GIC stacked interrupt controller domains
- Fixes for logicpd-somlv GPMC for Ethernet and NAND that clearly
have been broken since we changed GPMC to use the interrupt controller
binding for some pins. And fix the wrong pin muxing for WLAN while at it
- Fixes for am437x interrupt and dma properties to fix compiler warnings
that recently started happening
* tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-cm-t43: Correct the dmas property of spi0
ARM: dts: am4372: Correct the interrupts_properties of McASP
ARM: dts: logicpd-somlv: Fix wl127x pinmux
ARM: dts: logicpd-som-lv: Fix gpmc addresses for NAND and enet
ARM: dts: Fix omap4 hang with GPS connected to USB by using wakeupgen
ARM: OMAP2+: Missing error code in omap_device_build()
ARM: AM33xx: PRM: Remove am33xx_pwrdm_read_prev_pwrst function
ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context
ARM: dts: Add remote-wakeup-connected for omap OHCI
ARM: dts: am33xx: Add missing #phy-cells to ti,am335x-usb-phy
ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
ARM: OMAP2+: Fix smatch found issue for omap_device
ARM: OMAP2/3: CM: fix cm_split_idlest functionality
ARM: OMAP3: hwmod_data: add missing module_offs for MMC3
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaH174AAoJEFBXWFqHsHzOL+kIALWexxxRlwyOl75pkkZKTX2m
AsvVTq3jgjvNTJn8mjuhzYstgUr0/GqX1InG7eBeJwQPQj+mn1roElkd1wz09xXY
lKECXbTwQ0+Jc8Diomms5VvBD3y3OwaQVZKAPbTfI6A4nuUCaQdUVDMplP6dCoTI
FUcxbOvAppAFEeC3X04Gc2OdUpBRSiio8DE5nvuIGzIRvA9auc5YTbJ9sOtduj4o
lZvVgAHqccTmFgaFfPdW6T7h7uyZ1Jz5ItDx3BTk+QtWxFq+Cb9hOEJg/I+Z6QY+
2twJZxyXgpaWmdQkP18tSOEA8dGZDwIwhRG1ZEeeY0JNPw6dy5w9j1W1zijdCIk=
=RRYB
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.15:
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
* tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
Revert "ARM: dts: imx53: add srtc node"
ARM: dts: vf610-zii-dev-rev-c: Fix the I2C EEPROM address
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
-----BEGIN PGP SIGNATURE-----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=A6Ju
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.15,
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
* tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Fix PPI interrupt types
ARM: dts: NSP: Disable AHCI controller for HR NSP boards
ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC DT Fixes for v4.15
Add missing '#reset-cells' property to cpg nodes.
This flagged by recent dtc.
* tag 'renesas-dt-fixes-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a779x: Add '#reset-cells' in cpg-mssr
Signed-off-by: Olof Johansson <olof@lixom.net>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in Marvell dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
commit 200a575b68 ("ARM: dts: meson: organize devices in their corresponding busses")
organized all peripherals in busses so that the base register offset of
the bus doesn't have to be included in all child-nodes anymore.
The GPIO interrupt controller however specifies the register offset
without subtracting the "cbus" base address. This leads to a problem
where of_iomap inside the irq-meson-gpio driver fails because it
actually tries to map 0x182209880 (cbus base = 0xc1100000 + 0xc1109880
for the GPIO interrupt controller). Fix this by using 0x9880 as register
offset.
Fixes: 7d32bc03bc ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Nodes are sorted by their register start address. Move gpio_intc to the
correct position.
No functional changes intended.
Fixes: 7d32bc03bc ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This reverts commit 5b72505414.
The rtc block on i.MX53 is a completely different hardware than the
one found on i.MX25.
Cc: <stable@vger.kernel.org> #4.14
Reported-by: Noel Vellemans <Noel.Vellemans@visionbms.com>
Suggested-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
at24mac602 should be at the I2C address 0x50, so that it matches the
'reg' property.
Fixes: d4cd158176 ("ARM: dts: vf610-zii-dev: Add .dts file for rev. C")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following warnings:
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pin assignment for the wl127x interrupt was incorrect. I am
not sure how this every worked. This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working. This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.
Fixes: 44e4716499 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.
This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.
Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.
Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457f3 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.
Fixes: 7136d457f3 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Booting a kernel results in the kernel warning us about the following
PPI interrupts configuration:
[ 0.105127] smp: Bringing up secondary CPUs ...
[ 0.110545] GIC: PPI11 is secure or misconfigured
[ 0.110551] GIC: PPI13 is secure or misconfigured
Fix this by using the appropriate edge configuration for PPI11 and
PPI13, this is similar to what was fixed for Northstar (BCM5301X) in
commit 0e34079cd1 ("ARM: dts: BCM5301X: Correct GIC_PPI interrupt
flags").
Fixes: 7b2e987de2 ("ARM: NSP: add minimal Northstar Plus device tree")
Fixes: 1a9d53caba ("ARM: dts: NSP: Add TWD Support to DT")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.
Fixes: 70725d6e97 ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c37624 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
With the latest dtc, we get many warnings about the missing
'#reset-cells' property in these controllers, e.g.:
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /can@e6e80000:resets[0])
arch/arm/boot/dts/r8a7792-blanche.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/dma-controller@e6700000:resets[0])
arch/arm/boot/dts/r8a7792-wheat.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/ethernet@e6800000:resets[0])
arch/arm/boot/dts/r8a7793-gose.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /gpio@e6050000:resets[0])
arch/arm/boot/dts/r8a7794-alt.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /i2c@e6500000:resets[0])
arch/arm/boot/dts/r8a7794-silk.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /interrupt-controller@e61c0000:resets[0])
This adds it for the three r8a779x chips that were lacking it. The
binding mandates this as <1>, so this is the value I use.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[geert: Add fix for r8a7793.dtsi]
Fixes: 34fbd2b127 ("ARM: dts: r8a7790: Add reset control properties")
Fixes: 6e11a322f1 ("ARM: dts: r8a7792: Add reset control properties")
Fixes: 84fb19e1d2 ("ARM: dts: r8a7793: Add reset control properties")
Fixes: 615beb759c ("ARM: dts: r8a7794: Add reset control properties")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Pull ARM updates from Russell King:
- add support for ELF fdpic binaries on both MMU and noMMU platforms
- linker script cleanups
- support for compressed .data section for XIP images
- discard memblock arrays when possible
- various cleanups
- atomic DMA pool updates
- better diagnostics of missing/corrupt device tree
- export information to allow userspace kexec tool to place images more
inteligently, so that the device tree isn't overwritten by the
booting kernel
- make early_printk more efficient on semihosted systems
- noMMU cleanups
- SA1111 PCMCIA update in preparation for further cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (38 commits)
ARM: 8719/1: NOMMU: work around maybe-uninitialized warning
ARM: 8717/2: debug printch/printascii: translate '\n' to "\r\n" not "\n\r"
ARM: 8713/1: NOMMU: Support MPU in XIP configuration
ARM: 8712/1: NOMMU: Use more MPU regions to cover memory
ARM: 8711/1: V7M: Add support for MPU to M-class
ARM: 8710/1: Kconfig: Kill CONFIG_VECTORS_BASE
ARM: 8709/1: NOMMU: Disallow MPU for XIP
ARM: 8708/1: NOMMU: Rework MPU to be mostly done in C
ARM: 8707/1: NOMMU: Update MPU accessors to use cp15 helpers
ARM: 8706/1: NOMMU: Move out MPU setup in separate module
ARM: 8702/1: head-common.S: Clear lr before jumping to start_kernel()
ARM: 8705/1: early_printk: use printascii() rather than printch()
ARM: 8703/1: debug.S: move hexbuf to a writable section
ARM: add additional table to compressed kernel
ARM: decompressor: fix BSS size calculation
pcmcia: sa1111: remove special sa1111 mmio accessors
pcmcia: sa1111: use sa1111_get_irq() to obtain IRQ resources
ARM: better diagnostics with missing/corrupt dtb
ARM: 8699/1: dma-mapping: Remove init_dma_coherent_pool_size()
ARM: 8698/1: dma-mapping: Mark atomic_pool as __ro_after_init
..
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaC/4EAAoJEAhfPr2O5OEVQnsP/2JNpdLuzgwNp0p2gXrvK5pl
KOsA6Fld6RNmpuel8eHARbbDTPKF1Y1bvYXVo7lPhXb7KuM2IzG56VxoNech/5pX
eflKwnpV/Ns/ZMLYue7Rqdw0iZnjWESBWf5lzg9MvzwhZBaPlRwqu/aOJy360AZr
FnjKHtU/6WUIOCB8r0qLBDR/epoh7y2lKfjDTcEBrURrFEsTajdyd59npdMSIQqO
iUeeBVEIUKyytYDQNM/VOsBnh0G+2inLuykF8Nd6pYs8O0iUEUpZYwdGuwGUG1HB
VmCcRGU62efl5nu8zQMPnwAvjXwZAh8vbS0ha+B1vBJh1RwNVUz0kKIKEgAaOMZ3
zZa3NLfDP4cHgYtr2Xw2vSvJvDwQecmiItJKeZ/Id4cPy03TKEV1KEaHCQJHwbDn
RP/o9C+5gagMO/oIvZPQ+esVZXQ4prAzOdX53N7HPn4Wn+k4clkI0+hMvMGf67mo
EYOguCqbN2D0e11BLiPP1bRbGZRSI8I9xcKuhcw4ajJHbRRkrjl8EW7V6c8CuMkd
0Wj5oidFleJ0Vy+qQOPqXN1FwR7AbHNtI38JfWNz324AIrFCQERpfXVmKwRPZfl4
YXgGIA9fil3a01YJCtxc0PsXlRkveKJ8hKCLpjXbjNTh1oSbgrDxx5sMx9PO6WqJ
VOb6fL17rwTXlKV/GeU/
=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
This patch fixes the DTC warnings about missing property #phy-cells.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
There are some conflicts between staging and media trees,
as reported by Stephen Rothwell <sfr@canb.auug.org.au>.
So, merge from staging.
* tag 'staging-4.15-rc1': (775 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat a
bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnD+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynAmgCfSSr/9qiCE0vfP5eVYjddzxfWyZ4AoMbKORZC
5x2KVW0Btrbs3WmnD7ZU
=PSea
-----END PGP SIGNATURE-----
Merge tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat
a bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
tty: ehv_bytechan: fix spelling mistake
tty: serial: meson: allow baud-rates lower than 9600
serial: 8250_fintek: Fix crash with baud rate B0
serial: 8250_fintek: Disable delays for ports != 0
serial: 8250_fintek: Return -EINVAL on invalid configuration
tty: Remove redundant license text
tty: serdev: Remove redundant license text
tty: hvc: Remove redundant license text
tty: serial: Remove redundant license text
tty: add SPDX identifiers to all remaining files in drivers/tty/
tty: serial: jsm: remove redundant pointer ts
tty: serial: jsm: add space before the open parenthesis '('
tty: serial: jsm: fix coding style
tty: serial: jsm: delete space between function name and '('
tty: serial: jsm: add blank line after declarations
tty: serial: jsm: change the type of local variable
tty: serial: imx: remove dead code imx_dma_rxint
tty: serial: imx: disable ageing timer interrupt if dma in use
serial: 8250: fix potential deadlock in rs485-mode
serial: m32r_sio: Drop redundant .data assignment
...
Add remote-wakeup-connected for omap OHCI as that's needed by
ohci-platform driver.
Cc: devicetree@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
"ti,am335x-usb-phy" is using the phy binding, but is missing #phy-cells
property. Fixes the following warning in TI dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in OMAP dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
