We now queue packets to the policy if the states are not yet resolved,
this replaces the ancient sleeping code. Also the sleeping can cause
indefinite task hangs if the needed state does not get resolved.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
By semantics, xfrm layer is fully name space aware,
so will the locks, e.g. xfrm_state/pocliy_lock.
Ensure exclusive access into state/policy link list
for different name space with one global lock is not
right in terms of semantics aspect at first place,
as they are indeed mutually independent with each
other, but also more seriously causes scalability
problem.
One practical scenario is on a Open Network Stack,
more than hundreds of lxc tenants acts as routers
within one host, a global xfrm_state/policy_lock
becomes the bottleneck. But onces those locks are
decoupled in a per-namespace fashion, locks contend
is just with in specific name space scope, without
causing additional SPD/SAD access delay for other
name space.
Also this patch improve scalability while as without
changing original xfrm behavior.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
__xfrm4/6_state_addr_check is a four steps check, all we need to do
is checking whether the destination address match when looking SA
using wildcard source address. Passing saddr from flow is worst option,
as the checking needs to reach the fourth step while actually only
one time checking will do the work.
So, simplify this process by only checking destination address when
using wildcard source address for looking up SAs.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If SA is in the process of acquiring, which indicates this SA is more
promising and precise than the fall back option, i.e. using wild card
source address for searching less suitable SA.
So, here bail out, and try again.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Conflicts:
include/net/xfrm.h
Simple conflict between Joe Perches "extern" removal for function
declarations in header files and the changes in Steffen's tree.
Steffen Klassert says:
====================
Two patches that are left from the last development cycle.
Manual merging of include/net/xfrm.h is needed. The conflict
can be solved as it is currently done in linux-next.
1) We announce the creation of temporary acquire state via an asyc event,
so the deletion should be annunced too. From Nicolas Dichtel.
2) The VTI tunnels do not real tunning, they just provide a routable
IPsec tunnel interface. So introduce and use xfrm_tunnel_notifier
instead of xfrm_tunnel for xfrm tunnel mode callback. From Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
Creation of temporary SA are announced by netlink, but there is no notification
for the deletion.
This patch fix this asymmetric situation.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm_state timer should be independent of system clock change,
so switch to CLOCK_BOOTTIME base which is not only monotonic but
also counting suspend time.
Thus issue reported in commit: 9e0d57fd6d
("xfrm: SAD entries do not expire correctly after suspend-resume")
could ALSO be avoided.
v2: Use CLOCK_BOOTTIME to count suspend time, but still monotonic.
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In xfrm4 and xfrm6 we need to take care about sockets of the other
address family. This could happen because a 6in4 or 4in6 tunnel could
get protected by ipsec.
Because we don't want to have a run-time dependency on ipv6 when only
using ipv4 xfrm we have to embed a pointer to the correct local_error
function in xfrm_state_afinet and look it up when returning an error
depending on the socket address family.
Thanks to vi0ss for the great bug report:
<https://bugzilla.kernel.org/show_bug.cgi?id=58691>
v2:
a) fix two more unsafe interpretations of skb->sk as ipv6 socket
(xfrm6_local_dontfrag and __xfrm6_output)
v3:
a) add an EXPORT_SYMBOL_GPL(xfrm_local_error) to fix a link error when
building ipv6 as a module (thanks to Steffen Klassert)
Reported-by: <vi0oss@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The mark argument is read only, so constify it. Also make dummy_mark in
af_key const -- only used as dummy argument for this very function.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
By default, DSCP is copying during encapsulation.
Copying the DSCP in IPsec tunneling may be a bit dangerous because packets with
different DSCP may get reordered relative to each other in the network and then
dropped by the remote IPsec GW if the reordering becomes too big compared to the
replay window.
It is possible to avoid this copy with netfilter rules, but it's very convenient
to be able to configure it for each SA directly.
This patch adds a toogle for this purpose. By default, it's not set to maintain
backward compatibility.
Field flags in struct xfrm_usersa_info is full, hence I add a new attribute.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All users of xfrm_addr_cmp() use its result as boolean.
Introduce xfrm_addr_equal() (which is equal to !xfrm_addr_cmp())
and convert all users.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
afinfo->type_map and afinfo->mode_map deserve separated locks,
they are different things.
We should just take RCU read lock to protect afinfo itself,
but not for the inner pointers.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Similar to commit 418a99ac6a
(Replace rwlock on xfrm_policy_afinfo with rcu), the rwlock
on xfrm_state_afinfo can be replaced by RCU too.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Remove the check if x->km.state equal to XFRM_STATE_VALID in
xfrm_state_check_expire(), which will be done before call
xfrm_state_check_expire().
add a LINUX_MIB_XFRMOUTSTATEINVALID statistic to record the
outbound error due to invalid xfrm state.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Always store audit loginuids in type kuid_t.
Print loginuids by converting them into uids in the appropriate user
namespace, and then printing the resulting uid.
Modify audit_get_loginuid to return a kuid_t.
Modify audit_set_loginuid to take a kuid_t.
Modify /proc/<pid>/loginuid on read to convert the loginuid into the
user namespace of the opener of the file.
Modify /proc/<pid>/loginud on write to convert the loginuid
rom the user namespace of the opener of the file.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Paul Moore <paul@paul-moore.com> ?
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Conflicts:
net/netfilter/nfnetlink_log.c
net/netfilter/xt_LOG.c
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sematically speaking, xfrm_mgr.acquire is called when kernel intends to ask
user space IKE daemon to negotiate SAs with peers. IOW the direction will
*always* be XFRM_POLICY_OUT, so remove int dir for clarity.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After SA is setup, one timer is armed to detect soft/hard expiration,
however the timer handler uses xtime to do the math. This makes hard
expiration occurs first before soft expiration after setting new date
with big interval. As a result new child SA is deleted before rekeying
the new one.
Signed-off-by: Fan Du <fdu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
C assignment can handle struct in6_addr copying.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon "ip xfrm state update ..", xfrm_add_sa() takes an extra reference on
the user-supplied SA and forgets to drop the reference when
xfrm_state_update() returns 0. This leads to a memory leak as the
parameter SA is never freed. This change attempts to fix the leak by
calling __xfrm_state_put() when xfrm_state_update() updates a valid SA
(err = 0). The parameter SA is added to the gc list when the final
reference is dropped by xfrm_add_sa() upon completion.
Signed-off-by: Tushar Gohad <tgohad@mvista.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we clone a xfrm state we have to assign the replay_esn
and the preplay_esn pointers to the state if we use the
new replay detection method. To this end, we add a
xfrm_replay_clone() function that allocates memory for
the replay detection and takes over the necessary values
from the original state.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a netlink based user interface to configure
esn and big anti-replay windows. The new netlink attribute
XFRMA_REPLAY_ESN_VAL is used to configure the new implementation.
If the XFRM_STATE_ESN flag is set, we use esn and support for big
anti-replay windows for the configured state. If this flag is not
set we use the new implementation with 32 bit sequence numbers.
A big anti-replay window can be configured in this case anyway.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support multiple versions of replay detection, we move the replay
detection functions to a separate file and make them accessible
via function pointers contained in the struct xfrm_replay.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_state_migrate calls kfree instead of xfrm_state_put to free
a failed state. According to git commit 553f9118 this can cause
memory leaks.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The family parameter xfrm_state_find is used to find a state matching a
certain policy. This value is set to the template's family
(encap_family) right before xfrm_state_find is called.
The family parameter is however also used to construct a temporary state
in xfrm_state_find itself which is wrong for inter-family scenarios
because it produces a selector for the wrong family. Since this selector
is included in the xfrm_user_acquire structure, user space programs
misinterpret IPv6 addresses as IPv4 and vice versa.
This patch splits up the original init_tempsel function into a part that
initializes the selector respectively the props and id of the temporary
state, to allow for differing ip address families whithin the state.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfrm state genid only needs to be matched against the copy
saved in xfrm_dst. So we don't need a global genid at all. In
fact, we don't even need to initialise it.
Based on observation by Timo Teräs.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
pass mark to all SA lookups to prepare them for when we add code
to have them search.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
To see the effect make sure you have an empty SAD.
On window1 "ip xfrm mon" and on window2 issue "ip xfrm state flush"
You get prompt back in window2 and you see the flush event on window1.
With this fix, you still get prompt on window1 but no event on window2.
Thanks to Alexey Dobriyan for finding a bug in earlier version
when using pfkey to do the flushing.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Alexey Dobriyan:
--------------------
setkey now takes several seconds to run this simple script
and it spits "recv: Resource temporarily unavailable" messages.
#!/usr/sbin/setkey -f
flush;
spdflush;
add A B ipcomp 44 -m tunnel -C deflate;
add B A ipcomp 45 -m tunnel -C deflate;
spdadd A B any -P in ipsec
ipcomp/tunnel/192.168.1.2-192.168.1.3/use;
spdadd B A any -P out ipsec
ipcomp/tunnel/192.168.1.3-192.168.1.2/use;
--------------------
Obviously applications want the events even when the table
is empty. So we cannot make this behavioral change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric's version fixed it for pfkey. This one is for xfrm user.
I thought about amortizing those two get_acqseq()s but it seems
reasonable to have two of these sequence spaces for the two different
interfaces.
cheers,
jamal
commit d5168d5addbc999c94aacda8f28a4a173756a72b
Author: Jamal Hadi Salim <hadi@cyberus.ca>
Date: Tue Feb 16 06:51:22 2010 -0500
xfrm: avoid spinlock in get_acqseq() used by xfrm user
This is in the same spirit as commit 28aecb9d77
by Eric Dumazet.
Use atomic_inc_return() in get_acqseq() to avoid taking a spinlock
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_state_clone calls kfree instead of xfrm_state_put to free
a failed state. Depending on the state of the failed state, it
can cause leaks to things like module references.
All states should be freed by xfrm_state_put past the point of
xfrm_init_state.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To see the effect make sure you have an empty SAD.
-On window1 "ip xfrm mon"
-on window2 issue "ip xfrm state flush"
You get prompt back in window1
and you see the flush event on window2.
With this fix, you still get prompt on window1 but no
event on window2.
I was tempted to return -ESRCH on window1 (which would
show "RTNETLINK answers: No such process") but didnt want
to change current behavior.
cheers,
jamal
commit 5f3dd4a772326166e1bcf54acc2391df00dc7ab5
Author: Jamal Hadi Salim <hadi@cyberus.ca>
Date: Thu Feb 11 04:41:36 2010 -0500
xfrm: Flushing empty SAD generates false events
To see the effect make sure you have an empty SAD.
On window1 "ip xfrm mon" and on window2 issue "ip xfrm state flush"
You get prompt back in window1 and you see the flush event on window2.
With this fix, you still get prompt on window1 but no event on window2.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ip xfrm state|policy count" report SA/SP count from init_net,
not from netns of caller process.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a xfrm_state requires an authentication algorithm specified
either as xfrm_algo or as xfrm_algo_auth with a specific truncation
length. For compatibility, both attributes are dumped to userspace,
and we also accept both attributes, but prefer the new syntax.
If no truncation length is specified, or the authentication algorithm
is specified using xfrm_algo, the truncation length from the algorithm
description in the kernel is used.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following bug in the current implementation of
net/xfrm: SAD entries timeouts do not count the time spent by the machine
in the suspended state. This leads to the connectivity problems because
after resuming local machine thinks that the SAD entry is still valid, while
it has already been expired on the remote server.
The cause of this is very simple: the timeouts in the net/xfrm are bound to
the old mod_timer() timers. This patch reassigns them to the
CLOCK_REALTIME hrtimer.
I have been using this version of the patch for a few months on my
machines without any problems. Also run a few stress tests w/o any
issues.
This version of the patch uses tasklet_hrtimer by Peter Zijlstra
(commit 9ba5f0).
This patch is against 2.6.31.4. Please CC me.
Signed-off-by: Yury Polyanskiy <polyanskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up to use xfrm_addr_cmp() instead of compare addresses directly.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When kernel inserts a temporary SA for IKE, it uses the wrong hash
value for dst list. Two hash values were calcultated before: one with
source address and one with a wildcard source address.
Bug hinted by Junwei Zhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_lock() should be spin_unlock() in xfrm_state_walk_done().
caused by:
commit 12a169e7d8
"ipsec: Put dumpers on the dump list"
Reported-by: Marc Milgram <mmilgram@redhat.com>
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to make xfrm_state objects hash on source address
broke the case where such source addresses are wildcarded.
Fix this by doing a two phase lookup, first with fully specified
source address, next using saddr wildcarded.
Reported-by: Nicolas Dichtel <nicolas.dichtel@dev.6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Installing SAs using the XFRM_STATE_AF_UNSPEC fails on hosts with
support for one address family only. This patch accepts such SAs, even
if the processing of not supported packets will fail.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make
net.core.xfrm_aevent_etime
net.core.xfrm_acq_expires
net.core.xfrm_aevent_rseqth
net.core.xfrm_larval_drop
sysctls per-netns.
For that make net_core_path[] global, register it to prevent two
/proc/net/core antries and change initcall position -- xfrm_init() is called
from fs_initcall, so this one should be fs_initcall at least.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SA/SPD doesn't pin netns (and it shouldn't), so get rid of them by hand.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disallow spurious wakeups in __xfrm_lookup().
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State GC is per-netns, and this is part of it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
km_waitq is going to be made per-netns to disallow spurious wakeups
in __xfrm_lookup().
To not wakeup after every garbage-collected xfrm_state (which potentially
can be from different netns) make state GC list per-netns.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of this is implicit passing which netns's hashes should be resized.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hashtables are per-netns, they can be independently resized.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done to get
a) simple "something leaked" check
b) cover possible DoSes when other netns puts many, many xfrm_states
onto a list.
c) not miss "alien xfrm_state" check in some of list iterators in future.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid unnecessary complications with passing netns around.
* set once, very early after allocating
* once set, never changes
For a while create every xfrm_state in init_net.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides implementation of the enhancements of XFRM/PF_KEY MIGRATE mechanism
specified in draft-ebalard-mext-pfkey-enhanced-migrate-00. Defines associated
PF_KEY SADB_X_EXT_KMADDRESS extension and XFRM/netlink XFRMA_KMADDRESS
attribute.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu came up with the idea and the original patch to make
xfrm_state dump list contain also dumpers:
As it is we go to extraordinary lengths to ensure that states
don't go away while dumpers go to sleep. It's much easier if
we just put the dumpers themselves on the list since they can't
go away while they're going.
I've also changed the order of addition on new states to prevent
a never-ending dump.
Timo Teräs improved the patch to apply cleanly to latest tree,
modified iteration code to be more readable by using a common
struct for entries in the list, implemented the same idea for
xfrm_policy dumping and moved the af_key specific "last" entry
caching to af_key.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discovered by Timo Teräs, the currently xfrm_state_walk scheme
is racy because if a second dump finishes before the first, we
may free xfrm states that the first dump would walk over later.
This patch fixes this by storing the dumps in a list in order
to calculate the correct completion counter which cures this
problem.
I've expanded netlink_cb in order to accomodate the extra state
related to this. It shouldn't be a big deal since netlink_cb
is kmalloced for each dump and we're just increasing it by 4 or
8 bytes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we save states within a walk we need synchronisation
so that the list the saved state is on doesn't disappear from
under us.
As it stands this is done by keeping the state on the list which
is bad because it gets in the way of the management of the state
life-cycle.
An alternative is to make our own pseudo-RCU system where we use
counters to indicate which state can't be freed immediately as
it may be referenced by an ongoing walk when that resumes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit commit 4c563f7669 ("[XFRM]:
Speed up xfrm_policy and xfrm_state walking") inadvertently removed
larval states and socket policies from netlink dumps. This patch
restores them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since commit 4c563f7669
("[XFRM]: Speed up xfrm_policy and xfrm_state walking") it is
illegal to call __xfrm_state_destroy (and thus xfrm_state_put())
with xfrm_state_lock held. If we do, we'll deadlock since we
have the lock already and __xfrm_state_destroy() tries to take
it again.
Fix this by pushing the xfrm_state_put() calls after the lock
is dropped.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'audit.b50' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] new predicate - AUDIT_FILETYPE
[patch 2/2] Use find_task_by_vpid in audit code
[patch 1/2] audit: let userspace fully control TTY input auditing
[PATCH 2/2] audit: fix sparse shadowed variable warnings
[PATCH 1/2] audit: move extern declarations to audit.h
Audit: MAINTAINERS update
Audit: increase the maximum length of the key field
Audit: standardize string audit interfaces
Audit: stop deadlock from signals under load
Audit: save audit_backlog_limit audit messages in case auditd comes back
Audit: collect sessionid in netlink messages
Audit: end printk with newline
