SAMA5 SoCs embed an advanced NAND controller logic to automate READ/WRITE
page accesses. This advanced logic is exposed through a separate I/O mem
range and is thus represented in a different node with its own compatible.
Document the bindings of this nfc-io block.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The old NAND bindings were not exactly describing the hardware topology
and were preventing definitions of several NAND chips under the same
NAND controller.
New bindings address these limitations and should be preferred over the
old ones for new SoCs/boards.
Old bindings are still supported for backward compatibility but are
marked deprecated in the doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
This reverts commit 5ddc7bd43c ("mtd: atmel_nand: Support variable
RB_EDGE interrupts")
Because for current SoCs, the RB_EDGE3(i.e. bit 27) of HSMC_SR
register does not exist, the RB_EDGE0 (i.e. bit 24) is the ready/busy
line edge status bit. It is a datasheet bug.
Cc: <stable@vger.kernel.org>
Fixes: commit 5ddc7bd43c ("mtd: atmel_nand: Support variable RB_EDGE interrupts")
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As the SAMA5D2 controller supports the 32-bit ECC strength, accept it
as a valid setting when required by the device tree or the NAND
parameter page.
Then configure the controller to use this new setting.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Starting with the SAMA5D2, there is a new revision of the Atmel PMECC
controller that can correct 32 bits in each sector. This controller is
not 100% compatible with the previous revision that corrected a maximum
of 24 bits by sector, as some register addresses overlap.
Using information from the device tree, we can configure the driver to
work with both versions.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Do not mention which chips supporting the PMECC controller, as it a
duplicate of the information in the chips' device trees.
Use common terms when describing the sub-node for the NAND Flash
controller.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NFC controller used to accelerate the NAND transfers on SAMA5 chips
can use either RB_EDGE0 or RB_EDGE3 as its ready/busy interrupt bit.
Use the controller's compatible string to select the correct bit.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wenyou Yang <Wenyou.yang@atmel.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since in SAMA5D4 chip, the PMECC can correct bit flips in erased page.
So we add a DT property to indicate this hardware character.
If the PMECC support correct bitflip erased page (all data are 0xff).
Then we can use the PMECC correct the page and skip the erased page
check.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If there is no PMECC lookup table stored in ROM, or lookup table offset is
not specified, PMECC driver should build it in DDR by itself.
That make the PMECC driver work for some board which doesn't have PMECC
lookup table in ROM.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
For more information can refer to section 5.4 of PMECC controller
application note:
http://www.atmel.com/images/doc11127.pdf
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Retrieve the NFC clock to make sure it is enabled. Make that optional to ensure
compatibility with previous device trees but document it as mandatory so newer
device trees will include it.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch enable writing nand flash via NFC SRAM. It will minimize the CPU
overhead. The SRAM write only support ECC_NONE and ECC_HW with PMECC.
To enable this NFC write by SRAM feature, you can add a string in dts under
NFC driver node.
This driver has been tested on SAMA5D3X-EK with JFFS2, YAFFS2, UBIFS and
mtd-utils.
Here is part of mtd_speedtest (writing test) result, compare with non-NFC
writing, it reduces %65 cpu load with loss %12 speed.
- commands use to test:
# insmod /mnt/mtd_speedtest.ko dev=2 &
# top -n 30 -d 1 | grep speedtest
- test result:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64
mtd_speedtest: testing eraseblock write speed
509 495 root D 1164 0% 7% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 8% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 5% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock write speed is 5194 KiB/s
mtd_speedtest: testing page write speed
509 495 root D 1164 0% 32% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 27% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 25% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 30% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page write speed is 5024 KiB/s
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch will set the nand dma support in dts. Since we will not use
cpu_is_xxx() in nand driver. We needn't include the mach/cpu.h any more.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add comments to NAND "gpios" property to make it clearer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
