* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_reset must be called with sc->lock. Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While building latest Linus git, I hit the following:
CC [M] drivers/staging/bcm/Qos.o
drivers/staging/bcm/Qos.c: In function ‘PruneQueue’:
drivers/staging/bcm/Qos.c:367: error: ‘struct netdev_queue’ has no member named ‘tx_dropped’
drivers/staging/bcm/Qos.c: In function ‘flush_all_queues’:
drivers/staging/bcm/Qos.c:416: error: ‘struct netdev_queue’ has no member named ‘tx_dropped’
make[5]: *** [drivers/staging/bcm/Qos.o] Error 1
make[4]: *** [drivers/staging/bcm] Error 2
make[3]: *** [drivers/staging] Error 2
As well as:
CC [M] drivers/staging/bcm/Transmit.o
drivers/staging/bcm/Transmit.c: In function ‘SetupNextSend’:
drivers/staging/bcm/Transmit.c:163: error: ‘struct netdev_queue’ has no member named ‘tx_bytes’
drivers/staging/bcm/Transmit.c:164: error: ‘struct netdev_queue’ has no member named ‘tx_packets’
make[2]: *** [drivers/staging/bcm/Transmit.o] Error 1
tx_dropped/tx_bytes_tx_packets were removed in commit 1ac9ad13. This patch
converts bcm to use net_device_stats instead of netdev_queue.
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Update workqueue usage
RDMA/nes: Fix incorrect SFP+ link status detection on driver init
RDMA/nes: Fix SFP+ link down detection issue with switch port disable
RDMA/nes: Generate IB_EVENT_PORT_ERR/PORT_ACTIVE events
RDMA/nes: Fix bonding on iw_nes
IB/srp: Test only once whether iu allocation succeeded
IB/mlx4: Handle protocol field in multicast table
RDMA: Use vzalloc() to replace vmalloc()+memset(0)
mlx4_{core, ib, en}: Fix driver when sizeof (phys_addr_t) > sizeof (long)
IB/mthca: Fix driver when sizeof (phys_addr_t) > sizeof (long)
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.
Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: fix address space warnings in ioctl_fiemap()
aio: check return value of create_workqueue()
hpfs_setattr error case avoids unlock_kernel
compat: copy missing fields in compat_statfs64 to user
compat: update comment of compat statfs syscalls
compat: remove unnecessary assignment in compat_rw_copy_check_uvector()
fs: FS_POSIX_ACL does not depend on BLOCK
fs: Remove unlikely() from fget_light()
fs: Remove unlikely() from fput_light()
fallocate should be a file operation
make the feature checks in ->fallocate future proof
staging: smbfs building fix
tidy up around finish_automount()
don't drop newmnt on error in do_add_mount()
Take the completion of automount into new helper
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: balance asic_reset functions
drm/radeon/kms: remove duplicate card_posted() functions
drm/radeon/kms: add module option for pcie gen2
drm/radeon/kms: fix typo in evergreen safe reg
drm/nouveau: fix gpu page faults triggered by plymouthd
drm/nouveau: greatly simplify mm, killing some bugs in the process
drm/nvc0: enable protection of system-use-only structures in vm
drm/nv40: initialise 0x17xx on all chipsets that have it
drm/nv40: make detection of 0x4097-ful chipsets available everywhere
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (63 commits)
ARM: PL08x: cleanup comments
Update CONFIG_MD_RAID6_PQ to CONFIG_RAID6_PQ in drivers/dma/iop-adma.c
ARM: PL08x: fix a warning
Fix dmaengine_submit() return type
dmaengine: at_hdmac: fix race while monitoring channel status
dmaengine: at_hdmac: flags located in first descriptor
dmaengine: at_hdmac: use subsys_initcall instead of module_init
dmaengine: at_hdmac: no need set ACK in new descriptor
dmaengine: at_hdmac: trivial add precision to unmapping comment
dmaengine: at_hdmac: use dma_address to program DMA hardware
pch_dma: support new device ML7213 IOH
ARM: PL08x: prevent dma_set_runtime_config() reconfiguring memcpy channels
ARM: PL08x: allow dma_set_runtime_config() to return errors
ARM: PL08x: fix locking between prepare function and submit function
ARM: PL08x: introduce 'phychan_hold' to hold on to physical channels
ARM: PL08x: put txd's on the pending list in pl08x_tx_submit()
ARM: PL08x: rename 'desc_list' as 'pend_list'
ARM: PL08x: implement unmapping of memcpy buffers
ARM: PL08x: store prep_* flags in async_tx structure
ARM: PL08x: shrink srcbus/dstbus in txd structure
...
Without this fix reloading of the driver is impossible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes the mtdpart bug which allows users reading OOB past the
end of the partition. This happens because 'part_read_oob()' allows reading
multiple OOB areas in one go, and mtdparts does not validate the OOB
length in the request.
Although there is such check in 'nand_do_read_oob()' in nand_base.c, but
it checks that we do not read past the flash chip, not the partition,
because in nand_base.c we work with the whole chip (e.g., mtd->size
in nand_base.c is the size of the whole chip). So this check cannot
be done correctly in nand_base.c and should be instead done in mtdparts.c.
This problem was reported by Jason Liu <r64343@freescale.com> and reproduced
with nandsim:
$ modprobe nandsim first_id_byte=0x20 second_id_byte=0xaa third_id_byte=0x00 \
fourth_id_byte=0x15 parts=0x400,0x400
$ modprobe nandsim mtd_oobtest.ko dev=0
$ dmesg
= snip =
mtd_oobtest: attempting to read past end of device
mtd_oobtest: an error is expected...
mtd_oobtest: error: read past end of device
= snip =
mtd_oobtest: finished with 2 errors
Reported-by: Jason Liu <liu.h.jason@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Building error for smbfs:
drivers/staging/smbfs/dir.c:286: error: static declaration of 'smbfs_dentry_operations' follows non-static declaration
drivers/staging/smbfs/proto.h:42: error: previous declaration of 'smbfs_dentry_operations' was here
drivers/staging/smbfs/dir.c:294: error: static declaration of 'smbfs_dentry_operations_case' follows non-static declaration
drivers/staging/smbfs/proto.h:41: error: previous declaration of 'smbfs_dentry_operations_case' was here
make[3]: *** [drivers/staging/smbfs/dir.o] Error 1
make[2]: *** [drivers/staging/smbfs] Error 2
make[1]: *** [drivers/staging] Error 2
make[1]: *** Waiting for unfinished jobs....
Fix it by removing static keywords
Signed-off-by: Yang Ruirui <ruirui.r.yang@tieto.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* ib_wq is added, which is used as the common workqueue for infiniband
instead of the system workqueue. All system workqueue usages
including flush_scheduled_work() callers are converted to use and
flush ib_wq.
* cancel_delayed_work() + flush_scheduled_work() converted to
cancel_delayed_work_sync().
* qib_wq is removed and ib_wq is used instead.
This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
First, we were calling mc_stop() at the top of the function
which turns off all MC (memory controller) clients,
then checking if the GPU is idle. If it was idle we
returned without re-enabling the MC clients which would
lead to a blank screen, etc. This patch checks if the
GPU is idle before calling mc_stop().
Second, if the reset failed, we were returning without
re-enabling the MC clients. This patch re-enables
the MC clients before returning regardless of whether
the reset was successful or not.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching to pcie gen2 causes problems on some
boards. Add a module option to turn it on/off.
There are gen2 compatability issues with some
motherboards it seems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33027
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix gpu page faults triggered by plymouthd
drm/nouveau: greatly simplify mm, killing some bugs in the process
drm/nvc0: enable protection of system-use-only structures in vm
drm/nv40: initialise 0x17xx on all chipsets that have it
drm/nv40: make detection of 0x4097-ful chipsets available everywhere
The switch to separate BAR and channel address spaces made the fbcon memory
address calculation incorrect on NV50+ boards, this commit fixes that.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fix these:
drivers/nfc/pn544.c: In function 'pn544_read':
drivers/nfc/pn544.c:356: warning: comparison of distinct pointer types lacks a cast
drivers/nfc/pn544.c:377: warning: comparison of distinct pointer types lacks a cast
drivers/nfc/pn544.c: In function 'pn544_write':
drivers/nfc/pn544.c:463: warning: comparison of distinct pointer types lacks a cast
drivers/nfc/pn544.c:485: warning: comparison of distinct pointer types lacks a cast
Cc: "Matti J. Aaltonen" <matti.j.aaltonen@nokia.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup the formatting of comments, remove some which don't make sense
anymore.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[fix conflict with 96a608a4]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
During iw_nes initialization the link status for SFP+ PHY is always
detected as "up" regardless of real state (cable either connected or
disconnected). Add SFP+ PHY specific link status detection to the
iw_nes initialization procedure. Use link status recheck for
netdev_open to detect delayed state updates.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In case of SFP+ PHY, link status check at interrupt processing can
give false results. For proper link status change detection a delayed
recheck is needed to give nes registers time to settle. Add a
periodic link status recheck scheduled at interrupt to detect
potential delayed registers state changes.
Addresses: http://bugs.openfabrics.org/bugzilla/show_bug.cgi?id=2117
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Depending on link state change, IB_EVENT_PORT_ERR or
IB_EVENT_PORT_ACTIVE should be generated when handling MAC interrupts.
Plugging in a cable happens to result in series of interrupts changing
driver's link state a number of times before finally staying at link
up (e.g. link up, link down, link up, link down, ..., link up). To
prevent sending series of redundant IB_EVENT_PORT_ACTIVE and
IB_EVENT_PORT_ERR events, we use a timer to debounce them in
nes_port_ibevent().
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable configuring bonds on nes devices by adding missing support for
master net_device to the driver.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the following kconfig error after changing
CONFIGFS_FS -> select SYSFS:
fs/sysfs/Kconfig:1:error: recursive dependency detected!
fs/sysfs/Kconfig:1: symbol SYSFS is selected by CONFIGFS_FS
fs/configfs/Kconfig:1: symbol CONFIGFS_FS is selected by NETCONSOLE_DYNAMIC
drivers/net/Kconfig:3390: symbol NETCONSOLE_DYNAMIC depends on SYSFS
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: James Bottomley <James.Bottomley@suse.de>
Commit 415e12b237 ("PCI/ACPI: Request _OSC control once for each root
bridge (v3)") put the acpi_hest_init() call in acpi_pci_root_init() into
a wrong place, presumably because the author confused acpi_pci_disabled
with acpi_disabled. Bring the code ordering in acpi_pci_root_init()
back to sanity.
Additionally, make sure that hest_disable is set when acpi_disabled is
set, which is going to prevent acpi_hest_parse(), that still may be
executed for acpi_disabled=1 through aer_acpi_firmware_first(), from
crashing because of uninitialized hest_tab.
Reported-and-tested-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (23 commits)
sanitize vfsmount refcounting changes
fix old umount_tree() breakage
autofs4: Merge the remaining dentry ops tables
Unexport do_add_mount() and add in follow_automount(), not ->d_automount()
Allow d_manage() to be used in RCU-walk mode
Remove a further kludge from __do_follow_link()
autofs4: Bump version
autofs4: Add v4 pseudo direct mount support
autofs4: Fix wait validation
autofs4: Clean up autofs4_free_ino()
autofs4: Clean up dentry operations
autofs4: Clean up inode operations
autofs4: Remove unused code
autofs4: Add d_manage() dentry operation
autofs4: Add d_automount() dentry operation
Remove the automount through follow_link() kludge code from pathwalk
CIFS: Use d_automount() rather than abusing follow_link()
NFS: Use d_automount() rather than abusing follow_link()
AFS: Use d_automount() rather than abusing follow_link()
Add an AT_NO_AUTOMOUNT flag to suppress terminal automount
...
Instead of splitting refcount between (per-cpu) mnt_count
and (SMP-only) mnt_longrefs, make all references contribute
to mnt_count again and keep track of how many are longterm
ones.
Accounting rules for longterm count:
* 1 for each fs_struct.root.mnt
* 1 for each fs_struct.pwd.mnt
* 1 for having non-NULL ->mnt_ns
* decrement to 0 happens only under vfsmount lock exclusive
That allows nice common case for mntput() - since we can't drop the
final reference until after mnt_longterm has reached 0 due to the rules
above, mntput() can grab vfsmount lock shared and check mnt_longterm.
If it turns out to be non-zero (which is the common case), we know
that this is not the final mntput() and can just blindly decrement
percpu mnt_count. Otherwise we grab vfsmount lock exclusive and
do usual decrement-and-check of percpu mnt_count.
For fs_struct.c we have mnt_make_longterm() and mnt_make_shortterm();
namespace.c uses the latter in places where we don't already hold
vfsmount lock exclusive and opencodes a few remaining spots where
we need to manipulate mnt_longterm.
Note that we mostly revert the code outside of fs/namespace.c back
to what we used to have; in particular, normal code doesn't need
to care about two kinds of references, etc. And we get to keep
the optimization Nick's variant had bought us...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In case of single tx and rx queues, three MSI-x vectors are allocated instead
of two. This patch fixes that.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to cmd register is racey, especially in smp environments. Protect
it using a spinlock.
Signed-off-by: Matthieu Bucchianeri <matthieu@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility of a race where the suspend routine gets
called, while a napi callback is still pending and when that comes up,
it enables interrupts which just got disabled in the suspend routine.
This change adds napi disable call in suspend and enable in resume to
avoid race.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Show per-queue stats in ethtool -S output for vmxnet3 interface. Register dump
of ethtool should dump registers for all tx and rx queues.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a performance enhancement fix. vmxnet3 device performs better when
provided with at least 54 bytes (ethernet 14 + IP 20+ TCP 20) in the first SG
buffer. For UDP packets driver provides lesser than that in first sg. This
change fixes the same. Also avoid the redundant pskb_may_pull() call.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make hw vlan tag stripping as enabled by default. Thereby remove
the code to conditionally enable it later.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While activating the device get it's MAC address from netdev. This will allow
the MAC address configured using ifconfig to persist through the reset.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug while changing ring size when MTU is changed.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The physical address is never used by the device tree code when
allocating memory for unflattening. Change the architecture's alloc
hook to return the virutal address instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some OSA level have a bug in the hw tx csum logic. We can circumvent
this bug by turning on IP hw csum also.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The open function of qeth is not executed if the qeth device is in
state DOWN or HARDSETUP. A recovery switches from state SOFTSETUP to
HARDSETUP to DOWN to HARDSETUP and back to SOFTSETUP. If open and
recover are running concurrently, open fails if it hits the states
HARDSETUP or DOWN. This patch inserts waiting for recovery finish
in the qeth open functions to enable successful qeth device opening
in spite of a running recovery.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dentry op (d_manage) to permit a filesystem to hold a process and make it
sleep when it tries to transit away from one of that filesystem's directories
during a pathwalk. The operation is keyed off a new dentry flag
(DCACHE_MANAGE_TRANSIT).
The filesystem is allowed to be selective about which processes it holds and
which it permits to continue on or prohibits from transiting from each flagged
directory. This will allow autofs to hold up client processes whilst letting
its userspace daemon through to maintain the directory or the stuff behind it
or mounted upon it.
The ->d_manage() dentry operation:
int (*d_manage)(struct path *path, bool mounting_here);
takes a pointer to the directory about to be transited away from and a flag
indicating whether the transit is undertaken by do_add_mount() or
do_move_mount() skipping through a pile of filesystems mounted on a mountpoint.
It should return 0 if successful and to let the process continue on its way;
-EISDIR to prohibit the caller from skipping to overmounted filesystems or
automounting, and to use this directory; or some other error code to return to
the user.
->d_manage() is called with namespace_sem writelocked if mounting_here is true
and no other locks held, so it may sleep. However, if mounting_here is true,
it may not initiate or wait for a mount or unmount upon the parameter
directory, even if the act is actually performed by userspace.
Within fs/namei.c, follow_managed() is extended to check with d_manage() first
on each managed directory, before transiting away from it or attempting to
automount upon it.
follow_down() is renamed follow_down_one() and should only be used where the
filesystem deliberately intends to avoid management steps (e.g. autofs).
A new follow_down() is added that incorporates the loop done by all other
callers of follow_down() (do_add/move_mount(), autofs and NFSD; whilst AFS, NFS
and CIFS do use it, their use is removed by converting them to use
d_automount()). The new follow_down() calls d_manage() as appropriate. It
also takes an extra parameter to indicate if it is being called from mount code
(with namespace_sem writelocked) which it passes to d_manage(). follow_down()
ignores automount points so that it can be used to mount on them.
__follow_mount_rcu() is made to abort rcu-walk mode if it hits a directory with
DCACHE_MANAGE_TRANSIT set on the basis that we're probably going to have to
sleep. It would be possible to enter d_manage() in rcu-walk mode too, and have
that determine whether to abort or not itself. That would allow the autofs
daemon to continue on in rcu-walk mode.
Note that DCACHE_MANAGE_TRANSIT on a directory should be cleared when it isn't
required as every tranist from that directory will cause d_manage() to be
invoked. It can always be set again when necessary.
==========================
WHAT THIS MEANS FOR AUTOFS
==========================
Autofs currently uses the lookup() inode op and the d_revalidate() dentry op to
trigger the automounting of indirect mounts, and both of these can be called
with i_mutex held.
autofs knows that the i_mutex will be held by the caller in lookup(), and so
can drop it before invoking the daemon - but this isn't so for d_revalidate(),
since the lock is only held on _some_ of the code paths that call it. This
means that autofs can't risk dropping i_mutex from its d_revalidate() function
before it calls the daemon.
The bug could manifest itself as, for example, a process that's trying to
validate an automount dentry that gets made to wait because that dentry is
expired and needs cleaning up:
mkdir S ffffffff8014e05a 0 32580 24956
Call Trace:
[<ffffffff885371fd>] :autofs4:autofs4_wait+0x674/0x897
[<ffffffff80127f7d>] avc_has_perm+0x46/0x58
[<ffffffff8009fdcf>] autoremove_wake_function+0x0/0x2e
[<ffffffff88537be6>] :autofs4:autofs4_expire_wait+0x41/0x6b
[<ffffffff88535cfc>] :autofs4:autofs4_revalidate+0x91/0x149
[<ffffffff80036d96>] __lookup_hash+0xa0/0x12f
[<ffffffff80057a2f>] lookup_create+0x46/0x80
[<ffffffff800e6e31>] sys_mkdirat+0x56/0xe4
versus the automount daemon which wants to remove that dentry, but can't
because the normal process is holding the i_mutex lock:
automount D ffffffff8014e05a 0 32581 1 32561
Call Trace:
[<ffffffff80063c3f>] __mutex_lock_slowpath+0x60/0x9b
[<ffffffff8000ccf1>] do_path_lookup+0x2ca/0x2f1
[<ffffffff80063c89>] .text.lock.mutex+0xf/0x14
[<ffffffff800e6d55>] do_rmdir+0x77/0xde
[<ffffffff8005d229>] tracesys+0x71/0xe0
[<ffffffff8005d28d>] tracesys+0xd5/0xe0
which means that the system is deadlocked.
This patch allows autofs to hold up normal processes whilst the daemon goes
ahead and does things to the dentry tree behind the automouter point without
risking a deadlock as almost no locks are held in d_manage() and none in
d_automount().
Signed-off-by: David Howells <dhowells@redhat.com>
Was-Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: avoid pointless blocked-task warnings
rcu: demote SRCU_SYNCHRONIZE_DELAY from kernel-parameter status
rtmutex: Fix comment about why new_owner can be NULL in wake_futex_pi()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, olpc: Add missing Kconfig dependencies
x86, mrst: Set correct APB timer IRQ affinity for secondary cpu
x86: tsc: Fix calibration refinement conditionals to avoid divide by zero
x86, ia64, acpi: Clean up x86-ism in drivers/acpi/numa.c
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timekeeping: Make local variables static
time: Rename misnamed minsec argument of clocks_calc_mult_shift()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Remove syscall_exit_fields
tracing: Only process module tracepoints once
perf record: Add "nodelay" mode, disabled by default
perf sched: Fix list of events, dropping unsupported ':r' modifier
Revert "perf tools: Emit clearer message for sys_perf_event_open ENOENT return"
perf top: Fix annotate segv
perf evsel: Fix order of event list deletion
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
Commit f5e70d0fe3 renamed MD_RAID6_PQ to RAID6_PQ,
but iop-adma.c didn't update synchronously.
Signed-off-by: Wei Yongquan <weiyqlq@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We were reading channel status then taking a lock. This lead to a race because
this lock may delay us and then make this channel not idle anymore.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Place flags on first descriptor of chain instead of last.
This is the one used by atc_chain_complete() function while unmapping.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use subsys_initcall instead of module_init in order to keep DMA engine rolling
before other peripheral drivers.
Signed-off-by: Eric Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Following descriptor flow in at_hdmac driver, descriptor comming from
atc_desc_get() as already DMA_CTRL_ACK flag set. No need to set it again.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In atc_prep_slave_sg() function we use dma_address field of scatterlist with
sg_dma_address() macro instead of sg_phys(). DMA address is already computed
by dma_map_sg() or another mapping function in calling driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Support new device OKI SEMICONDUCTOR's ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use.
The ML7213 is companion chip for Intel Atom E6xx series.
The ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit dfe63bb0ad.
This commit was causing nouveau not to work properly, for -rc1 I'd
prefer it worked and we can look if this is useful for 2.6.39.
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/amba-pl022: fixing compilation warning.
spi: Enable SPI driver for S5P6440 and S5P6450
mmc: sdhci-of: fix build on non-powerpc platforms
spi/imx: Add i.MX53 support
spi/dw_spi: don't treat NULL clk as an error
spi: tegra: don't treat NULL clk as an error
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Encourage move to dev_pm_ops by warning on use of legacy methods
i2c: Factor out runtime suspend checks from PM operations
i2c: Unregister dummy devices last on adapter removal
clk_freq is used uninitialized in pl022_setup routine. This patch
fix compilation warning for using uninitialized variable
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: restore multiple bd_link_disk_holder() support
block cfq: compensate preempted queue even if it has no slice assigned
block cfq: make queue preempt work for queues from different workload
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
Since the PM core wishes to transition away from the legacy suspend
and resume methods and since removing them makes using PM core features
like runtime PM much easier start warning when a driver is registered
using the legacy methods.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When devices use dev_pm_ops the I2C API is implementing standard functionality
for integration with runtime PM and for checking for the presence of a per
device op. The PM core provides pm_generic_ functions implementing this
behaviour - use them to reduce coupling with future PM updates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: stable@kernel.org
Fixes the following:
1. POLL should not enable IRQ when work is not completed
2. No locking between TX descriptor cleaning and XMIT descriptor handling
3. No locking between RX POLL and XMIT modifying control register
4. Since TX cleaning (called from POLL) is running in parallel with XMIT
unnecessary locking is needed.
5. IRQ handler looks at RX frame status solely, this is wrong when IRQ is
temporarily disabled (in POLL), and when IRQ is shared.
6. IRQ handler clears IRQ status, which is unnecessary
7. TX queue was stopped in preventing cause when not MAX_SKB_FRAGS+1
descriptors were available after a SKB been scheduled by XMIT. Instead
the TX queue is stopped first when not enough descriptors are available
upon entering XMIT.
It was hard to split up this patch in smaller pieces since all are tied
together somehow.
Note the RX flag used in the interrupt handler does not signal that
interrupt was asserted, but that a frame was received. Same goes for TX.
Also, IRQ is not asserted when the RX flag is set before enabling IRQ
enable until a new frame is received. So extra care must be taken to
avoid enabling IRQ and all descriptors are already used, hence dead lock
will upon us. See new POLL implementation that enableds IRQ then look at
the RX flag to determine if one or more IRQs may have been missed. TX/RX
flags are cleared before handling previously enabled descriptors, this
ensures that the RX/TX flags are valid when determining if IRQ should be
turned on again.
By moving TX cleaning from POLL to XMIT in the standard case, removes some
locking trouble. Enabling TX cleaning from poll only when not enough TX
descriptors are available is safe because the TX queue is at the same time
stopped, thus XMIT will not be called. The TX queue is woken up again when
enough descriptrs are available.
TX Frames are always enabled with IRQ, however the TX IRQ Enable flag will
not be enabled until XMIT must wait for free descriptors.
Locking RX and XMIT parts of the driver from each other is needed because
the RX/TX enable bits share the same register.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frame error interrupts must also be handled since the RX flag only indicates
successful reception, it is unlikely but the old code may lead to dead lock
if 128 error frames are recieved in a row.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new SKB buffer should not be allocated when the old SKB is reused.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is safe to enable all fragments before enabling the first descriptor,
this way all descriptors don't have to be processed twice, added extra
memory barrier.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAPI is disabled there is no point in having IRQs enabled, TX/RX
should be off before clearing the TX/RX descriptor rings.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, not all CONFIG_OF platforms provide
pci_device_to_OF_node().
Change the test to CONFIG_SPARC for now to deal with
the build regressions.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915/lvds: Add AOpen i915GMm-HFS to the list of false-positive LVDS
agp/intel: Fix device names of i845 and 845G
drm/i915: Disable GPU semaphores on SandyBridge mobile
drm/i915/execbuffer: Clear domains before beginning reloc processing
drm/i915/execbuffer: Reorder relocations to match new object order
drm/i915: Fix error handler to capture the first batch after the seqno
drm/i915: Add a module option to override the use of SSC
drm/i915/panel: The backlight is enabled if the current value is non-zero
drm/i915/debugfs: Correct format after changing type of err object 'size'
Commit e09b457b (block: simplify holder symlink handling) incorrectly
assumed that there is only one link at maximum. dm may use multiple
links and expects block layer to track reference count for each link,
which is different from and unrelated to the exclusive device holder
identified by @holder when the device is opened.
Remove the single holder assumption and automatic removal of the link
and revive the per-link reference count tracking. The code
essentially behaves the same as before commit e09b457b sans the
unnecessary kobject reference count dancing.
While at it, note that this facility should not be used by anyone else
than the current ones. Sysfs symlinks shouldn't be abused like this
and the whole thing doesn't belong in the block layer at all.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milan Broz <mbroz@redhat.com>
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
* git://git.infradead.org/battery-2.6: (21 commits)
power_supply: Add MAX17042 Fuel Gauge Driver
olpc_battery: Fix up XO-1.5 properties list
olpc_battery: Add support for CURRENT_NOW and VOLTAGE_NOW
olpc_battery: Add support for CHARGE_NOW
olpc_battery: Add support for CHARGE_FULL_DESIGN
olpc_battery: Ambient temperature is not available on XO-1.5
jz4740-battery: Should include linux/io.h
s3c_adc_battery: Add gpio_inverted field to pdata
power_supply: Don't use flush_scheduled_work()
power_supply: Fix use after free and memory leak
gpio-charger: Fix potential race between irq handler and probe/remove
gpio-charger: Provide default name for the power_supply
gpio-charger: Check result of kzalloc
jz4740-battery: Check if platform_data is supplied
isp1704_charger: Detect charger after probe
isp1704_charger: Set isp->dev before anything needs it
isp1704_charger: Detect HUB/Host chargers
isp1704_charger: Correct length for storing model
power_supply: Add gpio charger driver
jz4740-battery: Protect against concurrent battery readings
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
mfd: ab8500-core chip version cut 2.0 support
mfd: Flag WM831x /IRQ as a wake source
mfd: Convert WM831x away from legacy I2C PM operations
regulator: Support MAX8998/LP3974 DVS-GPIO
mfd: Support LP3974 RTC
i2c: Convert SCx200 driver from using raw PCI to platform device
x86: OLPC: convert olpc-xo1 driver from pci device to platform device
mfd: MAX8998/LP3974 hibernation support
mfd/ab8500: remove spi support
mfd: Remove ARCH_U8500 dependency from AB8500
misc: Make AB8500_PWM driver depend on U8500 due to PWM breakage
mfd: Add __devexit annotation for vx855_remove
mfd: twl6030 irq_data conversion.
gpio: Fix cs5535 printk warnings
misc: Fix cs5535 printk warnings
mfd: Convert Wolfson MFD drivers to use irq_data accessor function
mfd: Convert TWL4030 to new irq_ APIs
mfd: Convert tps6586x driver to new irq_ API
mfd: Convert tc6393xb driver to new irq_ APIs
mfd: Convert t7166xb driver to new irq_ API
...
Make wakeup events be reported by the PCI subsystem before attempting to
resume devices or queuing up runtime resume requests for them, because
wakeup events should be reported as soon as they have been detected.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After recent changes related to wakeup events pm_wakeup_event()
automatically checks if the given device is configured to signal wakeup,
so pci_wakeup_event() may be a static inline function calling
pm_wakeup_event() directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI sysfs ROM interface requires an enabling write to access the ROM
image, but the default file mode is 0400. The original proposed patch
adding sysfs ROM support was a true read-only interface, with the
enabling bit coming in as a feature request. I suspect it was simply an
oversight that the file mode didn't get updated to match the API.
Acked-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
They got mixed up when the switch was converted to a table in 2007.
Signed-off-by: Oswald Buddenhagen <ossi@kde.org>
[ickle: minor changes for 2.6.37+]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit a1f5f22adc ("gpio: timbgpio:
irq_data conversion") was slightly too enthusiastic in converting
timbgpio_irq() over to take an irq_data * argument instead of an
unsigned int irq argument, as it is a flow handler, which still take
IRQ numbers for now. (And on top of that, it was using the wrong
accessors.)
This fixes it up, and seems to build without warnings.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LIO target is a full featured in-kernel target framework with the
following feature set:
High-performance, non-blocking, multithreaded architecture with SIMD
support.
Advanced SCSI feature set:
* Persistent Reservations (PRs)
* Asymmetric Logical Unit Assignment (ALUA)
* Protocol and intra-nexus multiplexing, load-balancing and failover (MC/S)
* Full Error Recovery (ERL=0,1,2)
* Active/active task migration and session continuation (ERL=2)
* Thin LUN provisioning (UNMAP and WRITE_SAMExx)
Multiprotocol target plugins
Storage media independence:
* Virtualization of all storage media; transparent mapping of IO to LUNs
* No hard limits on number of LUNs per Target; maximum LUN size ~750 TB
* Backstores: SATA, SAS, SCSI, BluRay, DVD, FLASH, USB, ramdisk, etc.
Standards compliance:
* Full compliance with IETF (RFC 3720)
* Full implementation of SPC-4 PRs and ALUA
Significant code cleanups done by Christoph Hellwig.
[jejb: fix up for new block bdev exclusive interface. Minor fixes from
Randy Dunlap and Dan Carpenter.]
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
SDEV_MEDIA_CHANGE event was first added by commit a341cd0f (SCSI: add
asynchronous event notification API) for SATA AN support and then
extended to cover generic media change events by commit 285e9670
([SCSI] sr,sd: send media state change modification events).
This event was mapped to block device in userland with all properties
stripped to simulate CHANGE event on the block device, which, in turn,
was used to trigger further userspace action on media change.
The recent addition of disk event framework kept this event for
backward compatibility but it turns out to be unnecessary and causes
erratic and inefficient behavior. The new disk event generates proper
events on the block devices and the compat events are mapped to block
device with all properties stripped, so the block device ends up
generating multiple duplicate events for single actual event.
This patch removes the compat event generation from both sr and sd as
suggested by Kay Sievers. Both existing and newer versions of udev
and the associated tools will behave better with the removal of these
events as they from the beginning were expecting events on the block
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace sd_media_change() with sd_check_events().
* Move media removed logic into set_media_not_present() and
media_not_present() and set sdev->changed iff an existing media is
removed or the device indicates UNIT_ATTENTION.
* Make sd_check_events() sets sdev->changed if previously missing
media becomes present.
* Event is reported only if sdev->changed is set.
This makes media presence event reported if scsi_disk->media_present
actually changed or the device indicated UNIT_ATTENTION. For backward
compatibility, SDEV_EVT_MEDIA_CHANGE is generated each time
sd_check_events() detects media change event.
[jejb: fix boot failure]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The MAX17042 is a fuel gauge with an I2C interface for lithium-ion
betteries. Unlike its predecessor MAX17040, MAX17042 uses 16bit
registers. Besides, MAX17042 has much more features than MAX17040; e.g.,
a thermistor, current and current accumulation measurement, battery
internal resistance estimate, average values of measurement, and others.
This patch implements a driver for MAX17042.
In this initial release, we have implemented the most basic features of
a fuel gauge: measure the battery capacity and voltage.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds support for chip version 2.0 or cut 2.0.
One new interrupt latch register - latch 12 - is introduced.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x can generate wake events, some unconditionally, so flag
the primary IRQ as a wake source in order to help the CPU treat the
/IRQ signal appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the legacy bus PM operations are deprecated move the suspend
method over to dev_pm_ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The previous driver did not support BUCK1-DVS3, BUCK1-DVS4, and
BUCK2-DVS2 modes. This patch adds such modes and an option to block
setting buck1/2 voltages out of the preset values.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.
If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.
This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The SCx200 ACB driver supports ISA hardware as well as PCI. The PCI
hardware is CS5535/CS5536 based, and the device that it grabs is handled by
the cs5535-mfd driver. This converts the SCx200 driver to use a
platform_driver rather than the previous PCI hackery.
The driver used to manually track the iface list (via linked list); now it
only does this for ISA devices. PCI ifaces are handled through standard
driver model lists.
It's unclear what happens in case of errors in the old ISA code; rather than
pretending the code actually cares, I've dropped the (implicit) ignorance
of return values and marked it with a comment.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the driver to save and restore register values
for hibernation.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the Ab8500 v1.0, the SPI support is deprecated on the HW.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While it is vanishingly unlikely that the device will be deployed on other
architectures removing the dependency facilitates build testing when doing
generic work on both the MFD core for the device and the subsystem drivers.
There appears to be no actual code dependency.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since we don't have a PWM API every PWM driver ends up exporting its
own version and we need to limit the platforms we try to build them on
in order to avoid multiple definitions. As the AB8500 is normally a
companion chip for the U8500 CPU depend on that architecture.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
drivers/gpio/cs5535-gpio.c: In function 'cs5535_gpio_probe':
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
drivers/misc/cs5535-mfgpt.c: In function 'cs5535_mfgpt_probe':
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Actually makes the code larger rathe rthan smaller but does provide some
isolation against core API changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to irq_chip
operations. Update the TWL4030 driver to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the tps6586x driver to the
new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being update to pass struct irq_data to irq_chip rather
than an irq number to operations. Update tc6393 to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data rather than an
irq number to irq_chip operations. Update the t7166xb driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the SMTPE driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to interrupt
operations, update the MAX8998 driver to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq infrastructure is being converted to pass struct irq_data rather
than an irq number to irq_chip operations, update max8925 to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the jz4740-adc driver to use the recently introduced IRQ API
variants which are passed struct irq_data rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to supply struct irq_data to chips
rather than the interrupt number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data rather than irq
numbers into chip drivers. As part of the update assignments to NULL for
unused operations are removed, these are not needed and the genirq docs
should be good enough.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The interrupt controller APIs are being updated to pass a struct irq_data
rather than the interrupt number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The interrupt controller APIs are being updated to pass a struct irq_data
rather than the interrupt number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of these are GPIO operations, though a couple are just internal only
functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Partly for coding style reasons, but mostly because sparse warns on it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We should specify both a start and an end for the IRQ range rather than
initialise the start twice.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There's no use of either of these outside of the driver so they can be
declared static.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
... and convert it to a dev_info print at probe time.
There are many variants of this chip with different values of VERSIONCRC.
The set of values is large, and not useful to enumerate. All are SW
compatible. The difference lies in default settings of the various power
rails, and other similar differences. The driver, or clients of the
driver, shouldn't be affected by this, since all rails should be
programmed into the desired state in all cases for correct operation.
Derived-from-code-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix the following section mismatch warning when building
omap2plus_defconfig:
WARNING: vmlinux.o(.data+0x47d7c): Section mismatch in reference
from the variable twl_driver to the function .init.text:twl_probe()
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the ioresources used by subdrivers to
retrieve their interrupt.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the system wake up from suspend when an
ab8500 interrupt occur. This can for example be USB cable
insert or an RTC alarm.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a file into sysfs for reading out chip id.
It has been requested for modem silent reboot.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Ludovic Barre <ludovic.barre@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We check for dev before dereferencing it.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds MODULE_ALIAS entries to the various cs5535 subdevice modules; this
allows the modules to automatically be loaded when cs5535-mfd loads.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the mfgpt driver a bunch.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the gpio driver a lot.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ARRAY_SIZE() returns size_t; use %zu instead of %d so that we don't
get warnings on x86-64.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow the WM8994 to completely power off, including disabling the LDOs
if they are software controlled, when it goes idle. The CODEC subdevice
controls activity for the MFD as a whole.
If the GPIOs need to be used while the device is active runtime PM
should be disabled for the device by machine specific code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow MFD cells to have pm_runtime_no_callbacks() called on them during
registration. This causes the runtime PM framework to ignore them,
allowing use of runtime PM to suspend the device as a whole even if
not all drivers for the MFD can usefully implement runtime PM. For
example, RTCs are likely to run continuously regardless of the power
state of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8326 is a high performance variant of the WM832x series with
no software visible differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All the current WM832x devices have the same set of subdevices so can
just use multiple case statements with a single body.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add an MFD driver to handle the ISA device on CS5535 and CS5536
southbridges. This ISA bridge is actually multiple devices: GPIOs,
MFGPTs, etc.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As warned by checkpatch.pl, use #include <linux/gpio.h> instead
of <asm/gpio.h>.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As warned by checkpatch.pl, use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some minor comment errors and whitespace issues discovered while looking
into this are also addressed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If hardware asserted an interrupt and driver is down,
then there is nothing to do so return IRQ_HANDLED
instead of IRQ_NONE. Returning IRQ_NONE in above
situation causes screaming IRQ on virtual machines.
CC: Andy Gospodarek <gospo@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hopefully, this is a temporary measure whilst the root cause is
understood. At the moment, we experience a hard hang whilst looping
urbanterror that has been identified as a result of the use of
semaphores, but so far only on SNB mobile.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32752
Tested-by: mengmeng.meng@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch enables the existing S3C64XX series SPI driver for S5P64X0
and removed dependency on EXPERIMENTAL because we don't need it now.
v3: Changed dependency of S3C64XX_DMA
v2: Removed dependency on EXPERIMENTAL
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Explicitly include err.h, of_address.h and of_irq.h.
Make use of machine_is() conditional on PPC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The firmware agent is not available during resume. Loading the firmware
during open() (see eee3a96c63) is not
enough.
close() is run during resume through rtl8169_reset_task(), whence the
mildly natural release of firmware in the driver removal method instead.
It will help with http://bugs.debian.org/609538. It will not avoid
the 60 seconds delay when:
- there is no firmware
- the driver is loaded and the device is not up before a suspend/resume
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jarek Kamiński <jarek@vilo.eu.org>
Cc: Hayes <hayeswang@realtek.com>
Cc: Ben Hutchings <benh@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use is_unicast_ether_addr from linux/etherdevice.h instead of custom
macros.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is completely untested as I don't have an ARM build environment.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ethtool operations can only be implemented for the WAN port, and
not all such operations are allowed to return an error code such as
-EOPNOTSUPP. Therefore, define two separate ethtool_ops structures
for WAN and non-WAN ports; simplify and rename the WAN-only functions.
This is completely untested as I don't have an ARM build environment.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_clone() dynamically allocates memory and may fail. If it does it
returns NULL. This means we'll dereference a NULL pointer in
drivers/net/usb/cdc_ncm.c::cdc_ncm_rx_fixup().
As far as I can tell, the proper way to deal with this is simply to goto
the error label.
Furthermore gcc complains that 'skb' may be used uninitialized:
drivers/net/usb/cdc_ncm.c: In function ‘cdc_ncm_rx_fixup’:
drivers/net/usb/cdc_ncm.c:922:18: warning: ‘skb’ may be used uninitialized in this function
and I believe it is right. On the line where we
pr_debug("invalid frame detected (ignored)" ...
we are using the local variable 'skb' but nothing has ever been assigned
to that variable yet. I believe the correct fix for that is to use
'skb_in' instead.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regardless of whether the firmware update being performed by
vxge_fw_upgrade() is a success or not we must still remember to always
release_firmware() before returning.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (59 commits)
ACPI / PM: Fix build problems for !CONFIG_ACPI related to NVS rework
ACPI: fix resource check message
ACPI / Battery: Update information on info notification and resume
ACPI: Drop device flag wake_capable
ACPI: Always check if _PRW is present before trying to evaluate it
ACPI / PM: Check status of power resources under mutexes
ACPI / PM: Rename acpi_power_off_device()
ACPI / PM: Drop acpi_power_nocheck
ACPI / PM: Drop acpi_bus_get_power()
Platform / x86: Make fujitsu_laptop use acpi_bus_update_power()
ACPI / Fan: Rework the handling of power resources
ACPI / PM: Register power resource devices as soon as they are needed
ACPI / PM: Register acpi_power_driver early
ACPI / PM: Add function for updating device power state consistently
ACPI / PM: Add function for device power state initialization
ACPI / PM: Introduce __acpi_bus_get_power()
ACPI / PM: Introduce function for refcounting device power resources
ACPI / PM: Add functions for manipulating lists of power resources
ACPI / PM: Prevent acpi_power_get_inferred_state() from making changes
ACPICA: Update version to 20101209
...
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
cpuidle/x86/perf: fix power:cpu_idle double end events and throw cpu_idle events from the cpuidle layer
intel_idle: open broadcast clock event
cpuidle: CPUIDLE_FLAG_CHECK_BM is omap3_idle specific
cpuidle: CPUIDLE_FLAG_TLB_FLUSHED is specific to intel_idle
cpuidle: delete unused CPUIDLE_FLAG_SHALLOW, BALANCED, DEEP definitions
SH, cpuidle: delete use of NOP CPUIDLE_FLAGS_SHALLOW
cpuidle: delete NOP CPUIDLE_FLAG_POLL
ACPI: processor_idle: delete use of NOP CPUIDLE_FLAGs
cpuidle: Rename X86 specific idle poll state[0] from C0 to POLL
ACPI, intel_idle: Cleanup idle= internal variables
cpuidle: Make cpuidle_enable_device() call poll_idle_init()
intel_idle: update Sandy Bridge core C-state residency targets
* 'stable/gntdev' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Fix module linking error.
xen p2m: clear the old pte when adding a page to m2p_override
xen gntdev: use gnttab_map_refs and gnttab_unmap_refs
xen: introduce gnttab_map_refs and gnttab_unmap_refs
xen p2m: transparently change the p2m mappings in the m2p override
xen/gntdev: Fix circular locking dependency
xen/gntdev: stop using "token" argument
xen: gntdev: move use of GNTMAP_contains_pte next to the map_op
xen: add m2p override mechanism
xen: move p2m handling to separate file
xen/gntdev: add VM_PFNMAP to vma
xen/gntdev: allow usermode to map granted pages
xen: define gnttab_set_map_op/unmap_op
Fix up trivial conflict in drivers/xen/Kconfig
* 'stable/platform-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen-platform: Fix compile errors if CONFIG_PCI is not enabled.
xen: rename platform-pci module to xen-platform-pci.
xen-platform: use PCI interfaces to request IO and MEM resources.
When working in RS485 mode, the atmel_serial driver keeps RTS high after
the initialization of the serial port. It goes low only after the first
character has been sent.
[akpm@linux-foundation.org: simplify code]
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Arkadiusz Bubala <arkadiusz.bubala@gmail.com>
Tested-by: Arkadiusz Bubala <arkadiusz.bubala@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (32 commits)
dm: raid456 basic support
dm: per target unplug callback support
dm: introduce target callbacks and congestion callback
dm mpath: delay activate_path retry on SCSI_DH_RETRY
dm: remove superfluous irq disablement in dm_request_fn
dm log: use PTR_ERR value instead of ENOMEM
dm snapshot: avoid storing private suspended state
dm snapshot: persistent make metadata_wq multithreaded
dm: use non reentrant workqueues if equivalent
dm: convert workqueues to alloc_ordered
dm stripe: switch from local workqueue to system_wq
dm: dont use flush_scheduled_work
dm snapshot: remove unused dm_snapshot queued_bios_work
dm ioctl: suppress needless warning messages
dm crypt: add loop aes iv generator
dm crypt: add multi key capability
dm crypt: add post iv call to iv generator
dm crypt: use io thread for reads only if mempool exhausted
dm crypt: scale to multiple cpus
dm crypt: simplify compatible table output
...
* 'for-linus' of git://neil.brown.name/md:
md: Fix removal of extra drives when converting RAID6 to RAID5
md: range check slot number when manually adding a spare.
md/raid5: handle manually-added spares in start_reshape.
md: fix sync_completed reporting for very large drives (>2TB)
md: allow suspend_lo and suspend_hi to decrease as well as increase.
md: Don't let implementation detail of curr_resync leak out through sysfs.
md: separate meta and data devs
md-new-param-to_sync_page_io
md-new-param-to-calc_dev_sboffset
md: Be more careful about clearing flags bit in ->recovery
md: md_stop_writes requires mddev_lock.
md/raid5: use sysfs_notify_dirent_safe to avoid NULL pointer
md: Ensure no IO request to get md device before it is properly initialised.
md: Fix single printks with multiple KERN_<level>s
md: fix regression resulting in delays in clearing bits in a bitmap
md: fix regression with re-adding devices to arrays with no metadata
When a RAID6 is converted to a RAID5, the extra drive should
be discarded. However it isn't due to a typo in a comparison.
This bug was introduced in commit e93f68a1fc in 2.6.35-rc4
and is suitable for any -stable since than.
As the extra drive is not removed, the 'degraded' counter is wrong and
so the RAID5 will not respond correctly to a subsequent failure.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When adding a spare to an active array, we should check the slot
number, but allow it to be larger than raid_disks if a reshape
is being prepared.
Apply the same test when adding a device to an
array-under-construction. It already had most of the test in place,
but not quite all.
Signed-off-by: NeilBrown <neilb@suse.de>
It is possible to manually add spares to specific slots before
starting a reshape.
raid5_start_reshape should recognised this possibility and include
it in the accounting.
Signed-off-by: NeilBrown <neilb@suse.de>
The values exported in the sync_completed file are unsigned long, which
overflows with very large drives, resulting in wrong values reported.
Since sync_completed uses sectors as unit, we'll start getting wrong
values with components larger than 2TB.
This patch simply replaces the use of unsigned long by unsigned long long.
Signed-off-by: Rémi Rérolle <rrerolle@lacie.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The sysfs attributes 'suspend_lo' and 'suspend_hi' describe a region
to which read/writes are suspended so that the under lying data can be
manipulated without user-space noticing.
Currently the window they describe can only move forwards along the
device. However this is an unnecessary restriction which will cause
problems with planned developments.
So relax this restriction and allow these endpoints to move
arbitrarily.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->curr_resync has artificial values of '1' and '2' which are used
by the code which ensures only one resync is happening at a time on
any given device.
These values are internal and should never be exposed to user-space
(except when translated appropriately as in the 'pending' status in
/proc/mdstat).
Unfortunately they are as ->curr_resync is assigned to
->curr_resync_completed and that value is directly visible through
sysfs.
So change the assignments to ->curr_resync_completed to get the same
valued from elsewhere in a form that doesn't have the magic '1' or '2'
values.
Signed-off-by: NeilBrown <neilb@suse.de>
Allow the metadata to be on a separate device from the
data.
This doesn't mean the data and metadata will by on separate
physical devices - it simply gives device-mapper and userspace
tools more flexibility.
Signed-off-by: NeilBrown <neilb@suse.de>
Add new parameter to 'sync_page_io'.
The new parameter allows us to distinguish between metadata and data
operations. This becomes important later when we add the ability to
use separate devices for data and metadata.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
When we allow for separate devices for data and metadata
in a later patch, we will need to be able to calculate
the superblock offset based on more than the bdev.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Setting ->recovery to 0 is generally not a good idea as it could clear
bits that shouldn't be cleared. In particular, MD_RECOVERY_FROZEN
should only be cleared on explicit request from user-space.
So when we need to clear things, just clear the bits that need
clearing.
As there are a few different places which reap a resync process - and
some do an incomplte job - factor out the code for doing the from
md_check_recovery and call that function instead of open coding part
of it.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
As md_stop_writes manipulates the sync_thread and calls md_update_sb,
it need to be called with mddev_lock held.
In all internal cases it is, but the symbol is exported for dm-raid to
call and in that case the lock won't be help.
Do make an exported version which takes the lock, and an internal
version which does not.
Signed-off-by: NeilBrown <neilb@suse.de>
With the module parameter 'start_dirty_degraded' set,
raid5_spare_active() previously called sysfs_notify_dirent() with a NULL
argument (rdev->sysfs_state) when a rebuild finished.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When an md device is in the process of coming on line it is possible
for an IO request (typically a partition table probe) to get through
before the array is fully initialised, which can cause unexpected
behaviour (e.g. a crash).
So explicitly record when the array is ready for IO and don't allow IO
through until then.
There is no possibility for a similar problem when the array is going
off-line as there must only be one 'open' at that time, and it is busy
off-lining the array and so cannot send IO requests. So no memory
barrier is needed in md_stop()
This has been a bug since commit 409c57f380 in 2.6.30 which
introduced md_make_request. Before then, each personality would
register its own make_request_fn when it was ready.
This is suitable for any stable kernel from 2.6.30.y onwards.
Cc: <stable@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: "Hawrylewicz Czarnowski, Przemyslaw" <przemyslaw.hawrylewicz.czarnowski@intel.com>
