Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
mmc1: new MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
On imx7s-warp the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
With this change HS200 error is gone and another benefit is that the
card can operate in DDR52 mode now:
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
Suggested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7 has two iomux controllers. the iomuxc and the iomuxc_lpsr.
In a board dts we have to make sure that both controllers are supplied
with the correct pins. It's way too easy to do this wrong since only
a look into the reference manual can reveal which pins belong to which
controller. To make this clearer add "LPSR" to the pin names which
belong to the LPSR controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog pin is controlled by the iomuxc_lpsr, not the regular
iomux, so move it there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
WaRP7 has a BCM43430 Bluetooth chip.
Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7s-warpd has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Warp7 has a BCM43430 Wifi chip connected to the USDHC1 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
warp7 has a sgtl5000 audio codec.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for MPL3115 NXP pressure sensor.
Tested by reading temperature and pressure:
$ cat /sys/bus/iio/devices/iio:device0/in_temp_raw
$ cat /sys/bus/iio/devices/iio:device0/in_pressure_raw
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
