The internal GPHYs need a firmware blob to function properly. This patch adds
the code needed to request the blob and load it to the PHY.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4523
The XRX200 family of SoCs has embedded gigabit PHYs. This patch adds code to
boot them up.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4522
Print the hardware revision and port/channel info when starting the dma core.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4520
The XRX200 SoC family has a different register layout for reading the boot
selection bits.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4519
Implement support for pinctrl on lantiq/xway socs. The IO core found on these
socs has the registers for pinctrl, pinconf and gpio mixed up in the same
register range. As the gpio_chip handling is only a few lines, the driver also
implements the gpio functionality. This obseletes the old gpio driver that was
located in the arch/ folder.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Lantiq socs have a General Purpose Timer Unit (GPTU). This driver allows us to
initialize the timers. The voice firmware needs these timers as a reference.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4236/
The xrx200 SoC family has the same PCI clock register layout as the AR9.
Enable the same quirk as for AR9
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4235/
Previously we relied on the bootloader to have enabled this bit. However some
bootloaders seem to not enable this for us.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4120/
The XRX200 based SoC have a different register offset for the interface
clock and PCI control registers. This patch detects the SoC and sets the
register offset at runtime. This make PCI work on the VR9 SoC.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4113/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
Now that all drivers are converted to OF we are able to remove some remaining
pieces of orphaned code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.
The following 2 patches will convert the drivers to OF.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch unifies all clock generation and gating code into one file.
All drivers will now be able to request their clocks via their device.
This patch also adds support for the clockout feature, which allows
clock generation on external pins.
Support for COMMON_CLK will be provided in the next series.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As part of the conversion to OF we also implement pinctrl drivers. Previously
we used ltq_gpio_request() to set pinmuxing. This is now obselete and we can
hence drop the function.
Additionally we remove gpio_to_irq() from the gpio driver and move it to a
header file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Before we are able to add OF support, we really want to drop all the bloat
needed to register all the platform devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3800/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the soc ids for additional xway socs. The patch also merges the amazon_se
code with the other socs.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct spelling "platfom" to "platform", "deactived" to "deactivated"
and "deprectated" to "deprecated" in arch/mips directory.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code located at arch/mips/lantiq/ included module.h to be able to use
the EXPORT_SYMBOL* macros. These can now be directly included using
export.h.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in arch/mips/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
To: LKML <linux-kernel@vger.kernel.org>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2540/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds the driver for the ETOP Packet Processing Engine (PPE32)
found inside the XWAY family of Lantiq MIPS SoCs. This driver makes 100MBit
ethernet work. Support for all 8 dma channels, gbit and the embedded switch
found on the ar9/vr9 still needs to be implemented.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2357/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the DMA engine found inside the XWAY family of
SoCs. The engine has 5 ports and 20 channels.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XWAY family allows to extend the number of gpios by using shift
registers or latches. This patch adds the 2 drivers needed for this. The
extended gpios are output only.
[ralf@linux-mips.org: Fixed ltq_stp_probe section() attributes.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2258/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the Lantiq XWAY family of Mips24KEc SoCs.
* Danube (PSB50702)
* Twinpass (PSB4000)
* AR9 (PSB50802)
* Amazon SE (PSB5061)
The Amazon SE is a lightweight SoC and has no PCI as well as a different
clock. We split the code out into seperate files to handle this.
The GPIO pins on the SoCs are multi function and there are several bits
we can use to configure the pins. To be as compatible as possible to
GPIOLIB we add a function
int lq_gpio_request(unsigned int pin, unsigned int alt0,
unsigned int alt1, unsigned int dir, const char *name);
which lets you configure the 2 "alternate function" bits. This way drivers like
PCI can make use of GPIOLIB without a cubersome wrapper.
The PLL code inside arch/mips/lantiq/xway/clk-xway.c is voodoo to me. It was
taken from a 2.4.20 source tree and was never really changed by me since then.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
