Driver needs to maintain a structure per-each concurrent possible
open aggregation, but the structure storing that metadata is far from
being optimized - biggest waste in it is that there are 2 buffer metadata,
one for a replacement buffer when the aggregation begins and the other for
holding the first aggregation's buffer after it begins [as firmware might
still update it]. Those 2 can safely be united into a single metadata
structure.
struct qede_agg_info changes the following:
/* size: 120, cachelines: 2, members: 9 */
/* sum members: 114, holes: 1, sum holes: 4 */
/* padding: 2 */
/* paddings: 2, sum paddings: 8 */
/* last cacheline: 56 bytes */
-->
/* size: 48, cachelines: 1, members: 9 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 48 bytes */
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates replacement buffers before-hand to make
sure whenever an aggregation begins there would be a replacement
for the Rx buffers, as we can't release the buffer until
aggregation is terminated and driver logic assumes the Rx rings
are always full.
For every other Rx page that's being allocated [I.e., regular]
the page is being completely mapped while for the replacement
buffers only the first portion of the page is being mapped.
This means that:
a. Once replacement buffer replenishes the regular Rx ring,
assuming there's more than a single packet on page we'd post unmapped
memory toward HW [assuming mapping is actually done in granularity
smaller than page].
b. Unmaps are being done for the entire page, which is incorrect.
Fixes: 55482edc25 ("qede: Add slowpath/fastpath support and enable hardware GRO")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver is now setting the ndev's priv_flags instead of adding to it,
causing pktgen failure to utilize various features due to the loss
of the IFF_TX_SKB_SHARING indication.
Fixes: 7b7e70f979 ("qed*: Allow unicast filtering")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the qed_lm_maps is closely tied with the QED_LM_* defines,
when iterating over the array use actual size instead of the qed
define to prevent future possible issues.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware is interested in various tidbits about
the driver - including the driver state & several configuration
related fields [MTU, primtary MAC, etc.].
This adds the necessray logic to update MFW with such configurations,
some of which are passed directly via qed while for others APIs
are provide so that qede would be able to later configure if needed.
This also introduces a new default configuration for MTU which would
replace the default inherited by being an ethernet device.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is configured to use Tx/Rx-only queues,
the length of the statistics would be shortened to accomodate only the
statistics required per-each queue, and the values would be provided
accordingly.
However, the strings provided would still contain both Tx and Rx strings
for each one of the queues [regardless of its configuration], which might
lead to out-of-bound access when filling the buffers as well as incorrect
statistics presented.
Fixes: 9a4d7e86ac ("qede: Add support for Tx/Rx-only queues.")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.
To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses incorrect APIs to unmap DMA memory which were
mapped using dma_map_single(). This patch fixes it to use
appropriate APIs for un-mapping DMA memory.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx indirection table entries are in the range [0, (rss_count - 1)]. If
user reduces the rss count, the table entries may not be in the ccorrect
range. Need to reconfigure the table with new rss_count as a basis.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current default values for Rx path i.e., 8 queues of 8Kb entries
each with 4Kb size, interface will consume 256Mb for Rx. The default values
causing the driver probe to fail when the system memory is low. Based on
the perforamnce results, rx-ring count value of 1Kb gives the comparable
performance with Rx coalesce timeout of 12 seconds. Updating the default
values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the execution of loopback test, driver may receive the packets which
are not originated by this test, loopback implementation need to skip those
packets.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS configuration is not supported for 100G adapters.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes in kernel ethtool implementation requires the driver
callback for get_channels() has to populate the values for max tx/rx
coalesce fields.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h
qlcnic: min_mtu 68, max_mtu 9600
CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not
actually performing unicast MAC filtering.
While we're at it - relax a hard-coded limitation that limits each
interface into using at most 15 unicast MAC addresses before turning
promiscuous. Instead utilize the HW resources to their limit.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to hardware limitation, when transmitting a geneve-encapsulated
packet with more than 32 bytes worth of geneve options the hardware
would not be able to crack the packet and consider it a regular UDP
packet.
This implements the ndo_features_check() in qede in order to prevent
GSO on said transmitted packets.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GSO support for GRE and UDP tunnels
where outer checksums are enabled.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hypervisors can support MAC hints to their VFs.
Even though we don't have such a hypervisor API in linux, we add
sufficient logic for the VF to be able to receive such hints and
set the mac accordingly - as long as the VF has not been set with
a MAC already.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qedr driver would require a tristate Kconfig option [to allow
it to compile as a module], and toward that end we've added the
INFINIBAND_QEDR option. But as we've made the compilation of the
qed/qede infrastructure required for RoCE dependent on the option
we'd be facing linking difficulties in case that QED=y or QEDE=y,
and INFINIBAND_QEDR=m.
To resolve this, we seperate between the INFINIBAND_QEDR option
and the infrastructure support in qed/qede by introducing a new
QED_RDMA option which would be selected by INFINIBAND_QEDR but would
be a boolean instead of a tristate; Following that, the qed/qede is
fixed based on this new option so that all config combinations would
be supported.
Fixes: cee9fbd8e2 ("qede: add qedr framework")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a skeletal implementation of the qede RoCE driver -
The qedr has some dependencies of the state of the underlying base
interface. This adds some logic required with mutual registrations
and the ability to pass updates on 'intresting' events.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/qlogic/qede/qede_main.c:2113:5: warning: no previous prototype for 'qede_set_features' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of the per-queue statistics introduced a harmless warning
on all 32-bit architectures:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function 'qede_get_ethtool_stats':
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
This changes the cast to 'void *' to shut up the warning, which
avoids the assumptions on the size of the pointer type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68db9ec2df ("qede: Add support for per-queue stats.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.
The major differences would be in:
- Recognizing that VF is running on top of a legacy PF.
- Returning some slowpath configurations that are no longer needed
on top of modern PFs, but would be required when working over
the legacy ones.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware for the qed* adpaters fixes several issues:
- Better blocking of malicious VFs.
- After FLR, Tx-switching [internal routing] of packets might
be incorrect.
- Deletion of unicast MAC filters would sometime have side-effect
of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.
In addition, it would allow driver some new functionality, including:
- Allowing PF/VF driver compaitibility with old drivers [running
pre-8.10.5.0 firmware].
- Better debug facilities.
This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.
At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.
While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].
Fixes: 312e06761c ("qede: Utilize xmit_more")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch touches various prints in the driver - it reduces the
verbosity of some prints [which were previously logged by default]
while adding several new debug prints and modifying others.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change qed* code in trivial manner; This isn't necessarily
semantic-only, but the end result is the same, i.e., no change
should occur from user perspective. Changes include:
- Using temporary variables to better fit 80-character restrictions.
- Removal of unused variables & code with no effect.
[plus some additional minor modifications].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make semantic-only adjustments to qed* drivers, such as:
- Changes in code indentation.
- Usage of BIT() macro.
- re-naming of variables.
- Re-ordering of variable declerations.
- Removal of (== 0) and (!= 0) in conditions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.
Please consider applying this to 'net-next' branch.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the necessary logic to prevet statistics reset
on inner-reload introduced a bug, and now statistics
are reset only when re-probing the driver.
Fixes: a0d26d5a4f ("qed*: Don't reset statistics on inner reload")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of ndo_vlan_rx_kill_vid() implementation,
qede is requesting firmware to remove the vlan filter.
This currently happens even if the vlan wasn't previously
added [In case device ran out of vlan credits].
For PFs this doesn't cause any issues as the firmware
would simply ignore the removal request. But for VFs their
parent PF is holding an accounting of the configured vlans,
and such a request would cause the PF to fail the VF's
removal request.
Simply fix this for both PFs & VFs and don't remove filters
that were not previously added.
Fixes: 7c1bfcad9f ("qede: Add vlan filtering offload support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses xmit_more optimization to reduce
number of TX doorbells write per packet.
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups qede_poll() routine a bit
and allows qede_poll() to do single iteration to handle
TX completion [As under heavy TX load qede_poll() might
run for indefinite time in the while(1) loop for TX
completion processing and cause CPU stuck].
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling IP fragmented packets with csum in their
transport header, the csum isn't changed as part of the
fragmentation. As a result, the packet containing the
transport headers would have the correct csum of the original
packet, but one that mismatches the actual packet that
passes on the wire. As a result, on receive path HW would
give an indication that the packet has incorrect csum,
which would cause qede to discard the incoming packet.
Since HW also delivers a notification of IP fragments,
change driver behavior to pass such incoming packets
to stack and let it make the decision whether it needs
to be dropped.
Signed-off-by: Manish <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
