Extend the LED backlight tirgger driver with an option that allows for
inverting the trigger output polarity.
With the invertion option provided, I (ab)use the backlight trigger for
driving a LED that indicates LCD display blank condtition on my Amstrad
Delta videophone. Since the machine has no dedicated power LED, it was
not possible to distinguish if the display was blanked, or the machine was
turned off, without touching it.
The invert sysfs control is patterned after a similiar function of the GPIO
trigger driver.
[akpm@linux-foundation.org: make output match input, tighten input checking]
[akpm@linux-foundation.org: make output match input, tighten input checking]
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the led device name is fetched from the device_type in
I2C_BOARD_INFO which comes from the platform data. This name is in turn
used to create an entry in sysfs.
If there exists two or more lp5521 on a particular platform, the
device_type in I2C_BOARD_INFO has to be the same, else lp5521 driver probe
wont be called and if used so, results in run time warning "cannot create
sysfs with same name" and hence a failure.
The name that is used to create sysfs entry is to be passed by the struct
led_platform_data. Hence adding an element of type const char * and
change in lp5521 driver to use this name in creating the led device if
present else use the name obtained by I2C_BOARD_INFO.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver contained possibility for circular locking.
One lock is held by sysfs-core and another one by the driver itself. This
happened when the driver created or removed sysfs entries dynamically.
There is no real need to do those operations. Now all the sysfs entries
are created at probe and removed at removal. Engine load sysfs entries
are now visible all the time. However, access to the entries fails if the
engine is disabled or running.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Arun Murthy <arun.murthy@stericsson.com>
Reviewed-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver contained possibility for circular locking.
One lock is held by sysfs-core and another one by the driver itself. This
happened when the driver created or removed sysfs entries dynamically.
There is no real need to do those operations. Now all the sysfs entries
are created at probe and removed at removal. Engine load and mux
configuration sysfs entries are now visible all the time. However, access
to the entries fails if the engine is disabled or running.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Arun Murthy <arun.murthy@stericsson.com>
Reviewed-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently all leds channels begins with string lp5523. Patch adds a
possibility to provide name via platform data. This makes it possible to
have several chips without overlapping sysfs names.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Arun Murthy <arun.murthy@stericsson.com>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Remove unneeded input_free_device() after input_unregister_device().
- Add pca9532_destroy_devices() function for destroy devices.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code doesn't check first sscanf() return value. If first sscanf()
failed then c contains some garbage. It might lead to reading
uninitialised stack data in the second sscanf() call.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (39 commits)
i915/gtt: fix ordering causing DMAR errors on object teardown.
i915/gtt: fix ordering issues with status setup and DMAR
drm/i915/execbuffer: Reorder binding of objects to favour restrictions
drm/i915: If we hit OOM when allocating GTT pages, clear the aperture
drm/i915/evict: Ensure we completely cleanup on failure
drm/i915/execbuffer: Correctly clear the current object list upon EFAULT
drm/i915/debugfs: Show all objects in the gtt
drm/i915: Record AGP memory type upon error
drm/i915: Periodically flush the active lists and requests
drm/i915/gtt: Unmap the PCI pages after unbinding them from the GTT
drm/i915: Record the error batchbuffer on each ring
drm/i915: Include TLB miss overhead for computing WM
drm/i915: Propagate error from flushing the ring
drm/i915: detect & report PCH display error interrupts
drm/i915: cleanup rc6 code
drm/i915: fix rc6 enabling around suspend/resume
drm/i915: re-enable rc6 support for Ironlake+
drm/i915: Make the ring IMR handling private
drm/i915/ringbuffer: Simplify the ring irq refcounting
drm/i915/debugfs: Show the per-ring IMR
...
* 'stable/xenbus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/xenbus: making backend support modular is too complex
xen/pci: Make xen-pcifront be dependent on XEN_XENBUS_FRONTEND
xen/xenbus: fixup checkpatch issues in xenbus_probe*
xen/netfront: select XEN_XENBUS_FRONTEND
xen/xenbus: clean up noise in xenbus_probe_frontend.c
xen/xenbus: clean up noise in xenbus_probe_backend.c
xen/xenbus: clean up noise in xenbus_probe.c
xen/xenbus: cleanup debug noise in xenbus_comms.c
xen/xenbus: clean up error handling
xen/xenbus: make frontend bus GPL
xen/xenbus: make sure backend bus is registered earlier
xenbus/frontend: register bus earlier
xen: remove xen/evtchn.h
xen: add backend driver support
xen: separate out frontend xenbus
Previous to the last GTT rework we always rewrote the GTT then unmapped the
object, somehow this got reversed in the rework in 2.6.37-rc5 timeframe.
This fix needs to go to stable in an alternate form since the code changed.
This fixes DMAR reports on my Ironlake HP2540p.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code was setting up the status page before setting the DMAR-is-on-bit,
so we were getting DMAR errors on the status page. Reverse the two bits
of init code to the correct result.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of ssh://master.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel: (37 commits)
drm/i915/execbuffer: Reorder binding of objects to favour restrictions
drm/i915: If we hit OOM when allocating GTT pages, clear the aperture
drm/i915/evict: Ensure we completely cleanup on failure
drm/i915/execbuffer: Correctly clear the current object list upon EFAULT
drm/i915/debugfs: Show all objects in the gtt
drm/i915: Record AGP memory type upon error
drm/i915: Periodically flush the active lists and requests
drm/i915/gtt: Unmap the PCI pages after unbinding them from the GTT
drm/i915: Record the error batchbuffer on each ring
drm/i915: Include TLB miss overhead for computing WM
drm/i915: Propagate error from flushing the ring
drm/i915: detect & report PCH display error interrupts
drm/i915: cleanup rc6 code
drm/i915: fix rc6 enabling around suspend/resume
drm/i915: re-enable rc6 support for Ironlake+
drm/i915: Make the ring IMR handling private
drm/i915/ringbuffer: Simplify the ring irq refcounting
drm/i915/debugfs: Show the per-ring IMR
drm/i915: Mask USER interrupts on gen6 (until required)
drm/i915: Handle ringbuffer stalls when flushing
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (67 commits)
cxgb4vf: recover from failure in cxgb4vf_open()
netfilter: ebtables: make broute table work again
netfilter: fix race in conntrack between dump_table and destroy
ah: reload pointers to skb data after calling skb_cow_data()
ah: update maximum truncated ICV length
xfrm: check trunc_len in XFRMA_ALG_AUTH_TRUNC
ehea: Increase the skb array usage
net/fec: remove config FEC2 as it's used nowhere
pcnet_cs: add new_id
tcp: disallow bind() to reuse addr/port
net/r8169: Update the function of parsing firmware
net: ppp: use {get,put}_unaligned_be{16,32}
CAIF: Fix IPv6 support in receive path for GPRS/3G
arp: allow to invalidate specific ARP entries
net_sched: factorize qdisc stats handling
mlx4: Call alloc_etherdev to allocate RX and TX queues
net: Add alloc_netdev_mqs function
caif: don't set connection request param size before copying data
cxgb4vf: fix mailbox data/control coherency domain race
qlcnic: change module parameter permissions
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (72 commits)
powerpc/pseries: Fix build of topology stuff without CONFIG_NUMA
powerpc/pseries: Fix VPHN build errors on non-SMP systems
powerpc/83xx: add mpc8308_p1m DMA controller device-tree node
powerpc/83xx: add DMA controller to mpc8308 device-tree node
powerpc/512x: try to free dma descriptors in case of allocation failure
powerpc/512x: add MPC8308 dma support
powerpc/512x: fix the hanged dma transfer issue
powerpc/512x: scatter/gather dma fix
powerpc/powermac: Make auto-loading of therm_pm72 possible
of/address: Use propper endianess in get_flags
powerpc/pci: Use printf extension %pR for struct resource
powerpc: Remove unnecessary casts of void ptr
powerpc: Disable VPHN polling during a suspend operation
powerpc/pseries: Poll VPA for topology changes and update NUMA maps
powerpc: iommu: Add device name to iommu error printks
powerpc: Record vma->phys_addr in ioremap()
powerpc: Update compat_arch_ptrace
powerpc: Fix PPC_PTRACE_SETHWDEBUG on PPC_BOOK3S
powerpc/time: printk time stamp init not correct
powerpc: Minor cleanups for machdep.h
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Fix refcount leak in lkey/rkey validation
IB/qib: Improve SERDES tunning on QMH boards
IB/qib: Unnecessary delayed completions on RC connection
IB/qib: Issue pre-emptive NAKs on eager buffer overflow
IB/qib: RDMA lkey/rkey validation is inefficient for large MRs
IB/qib: Change QPN increment
IB/qib: Add fix missing from earlier patch
IB/qib: Change receive queue/QPN selection
IB/qib: Fix interrupt mitigation
IB/qib: Avoid duplicate writes to the rcv head register
IB/qib: Add a few new SERDES tunings
IB/qib: Reset packet list after freeing
IB/qib: New SERDES init routine and improvements to SI quality
IB/qib: Clear WAIT_SEND flags when setting QP to error state
IB/qib: Fix context allocation with multiple HCAs
IB/qib: Fix multi-Florida HCA host panic on reboot
IB/qib: Handle transitions from ACTIVE_DEFERRED to ACTIVE better
IB/qib: UD send with immediate receive completion has wrong size
IB/qib: Set port physical state even if other fields are invalid
IB/qib: Generate completion callback on errors
...
If the Link Start fails in cxgb4vf_open(), we need to back out any state
that we've built up ...
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mappable portion of the aperture is always a small subset at the
start of the GTT, it is allocated preferentially by drm_mm. This is
useful in case we ever need to map an object later. However, if you have
a large object that can consume the entire mappable region of the
GTT this prevents the batchbuffer from fitting and so causing an error.
Instead allocate all those that require a mapping up front in order to
improve the likelihood of finding sufficient space to bind them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than evicting an object at random, which is unlikely to alleviate
the memory pressure sufficient to allow us to continue, zap the entire
aperture. That should give the system long enough to recover and reap
some pages from the evicted objects, forestalling the allocation error
for the new object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Before releasing the lock in order to copy the relocation list from user
pages, we need to drop all the object references as another thread may
usurp and execute another batchbuffer before we reacquire the lock.
However, the code was buggy and failed to clear the list...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
In order to retire active buffers whilst no client is active, we need to
insert our own flush requests onto the ring.
This is useful for servers that queue up some rendering and then go to
sleep as it allows us to the complete processing of those requests,
potentially making that memory available again much earlier.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently the skb array is not fully allocated, and the allocation
is done as it's requested, which is not the expected way.
This patch just allocate the full skb array at driver initialization.
Also, this patch increases ehea version to 107.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs:
add another ID of "corega Ether CF-TD" 10Base-T PCMCIA card.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie spotted that his ILK laptop with DMAR enabled was generating
the occasional DMAR warning.
"The ordering in the previous code was to rewrite the GTT table before
unmapping the pages and that makes sense to me."
This is his stable patch ported to d-i-n.
Reported-by: Dave Airlie <airlied@redhat.com>
Original-patch-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The docs recommend that if 8 display lines fit inside the FIFO buffer,
then the number of watermark entries should be increased to hide the
latency of filling the rest of the FIFO buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI and the transcoders can fail for various reasons, so detect those
conditions and report on them.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cleanup several aspects of the rc6 code:
- misnamed intel_disable_clock_gating function (was only about rc6)
- remove commented call to intel_disable_clock_gating
- rc6 enabling code belongs in its own function (allows us to move the
actual clock gating enable call back into restore_state)
- allocate power & render contexts up front, only free on unload
(avoids ugly lazy init at rc6 enable time)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: checkpatch cleanup]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enabling RC6 implies setting a graphics context. Make sure we do that
only after the ring has been enabled, otherwise our ring commands will
hang.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Re-enable rc6 support on Ironlake for power savings. Adds a debugfs
file to check current RC state, adds a missing workaround for Ironlake
MI_SET_CONTEXT instructions, and renames MCHBAR_RENDER_STANDBY to
RSTDBYCTL to match the docs.
Keep RC6 and the power context disabled on pre-ILK. It only seems to
hang and doesn't save any power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As the IMR for the USER interrupts are not modified elsewhere, we can
separate the spinlock used for these from that of hpd and pipestats.
Those two IMR are manipulated under an IRQ and so need heavier locking.
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to ensure that writes through the GTT land before any
modification to the MMIO registers and so must impose a mandatory write
barrier when flushing the GTT domain. This was revealed by relaxing the
write ordering by experimentally mapping the registers and the GATT as
write-combining.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As has_gem is unconditionally set to true, the conditional immediately
following that assignment is superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These functions need to be reworked for Ironlake and above, but until
then at least avoid reading non-existent registers.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: combine with a gratuitous tidy]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When bringing up new hardware, or otherwise experimenting, GPU hangs are
a way of life. However, the automatic GPU reset can do more harm than
good under these circumstances, as we may wish to capture a full trace for
debugging.
Based on a patch by Zhenyu Wang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake, the LP0 latency is hardcoded and in ns unit, while on
Sandybridge, it comes from a register and with unit 0.1 us. So, fix
the wrong latency value while computing wm0 on Ironlake and Sandybridge.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch actually makes the watermark code even uglier (if that's
possible), but has the advantage of sharing code between SNB and ILK at
least. Longer term we should refactor the watermark stuff into its own
file and clean it up now that we know how it's supposed to work.
Supporting WM2 on my Vaio reduced power consumption by around 0.5W, so
this patch is definitely worthwhile (though it also needs lots of test
coverage).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: pass the watermark structs arounds]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Flush the chipset write buffers before and after adjusting the GTT base
register, just in case. We only modify this value upon initialisation
(boot and resume) so there should be no outstanding writes, however
there are always those persistent PGTBL_ER that keep getting reported
upon resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On i830 if the tail pointer is set to within 2 cachelines of the end of
the buffer, the chip may hang. So instead if the tail were to land in
that location, we pad the end of the buffer with NOPs, and start again
at the beginning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In some configuration, the PCU may allow us to overclock the GPU.
Check for this case and adjust the max frequency as appropriate. Also
initialize the min/max frequencies to default values as indicated by
hardware.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... and just any combination of bits & ~PFIT_ENABLE. This way we do not
attempt disable to the panel fitter controller uselessly upon
intel_lvds_disable().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Alex Fiestas reported an issue with his HDMI connector being misdetected
as DVI unless he had something connected upon boot. By moving the
decision as to whether to use HDMI or DVI encoding for the HDMI capable
output until we probe the monitor means that we should avoid sending a
HDMI signal to a DVI monitor and also correctly detect hardware like
Alex's.
However, to really determine what connector is soldered onto the wire we
need to inspect the VBT sdvo child devices - but can we trust it?
Reported-by: Alex Fiestas <alex@eyeos.org>
Tested-by: Alex Fiestas <alex@eyeos.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32828
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Some voltage swing/pre-emphasis level use the same value on eDP
Sandybridge, like 400mv_0db and 600mv_0db are with the same value
of (0x0 << 22). So, fix them, and point out the value if it isn't
a supported voltage swing/pre-emphasis level.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Since Linux 2.6.36 the digital output on my system (855GME + DVI-I) is
not working any longer. The analog output is always activated
regardless of the type of monitor attached.
The culprit seems to be intel_crt_detect_ddc(), which returns true as
soon as an ACK from the EDID device is received. Obviously this
approach does not work with DVI-I where the analog and digital outputs
share a common DDC bus.
In a similar manner to the shared DDC wire, ala the "Mac Mini Hack", we
need an additional check to make sure that there really is an analog
device attached to the DDC.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
When trying to do channel equalization, we need to make sure we still
have clock recovery on all lanes while training. We also need to try
clock recovery again if we lose the clock or if channel eq fails 5
times. We'll try clock recovery up to 5 more times before giving up
entirely.
Gets suspend/resume working on my Vaio again and brings us back into
compliance with the DP training sequence spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were using a stale pointer in the check which caused us to use CPU
attached DP params when we should have been using PCH attached params.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31988
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Christoph Lukas <christoph.lukas@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rtc: Namespace fixup
RTC: Remove UIE emulation
RTC: Rework RTC code to use timerqueue for events
Fix up trivial conflict in drivers/rtc/rtc-dev.c
The mr optimization introduced a reference count leak on an exception
test. The lock/refcount manipulation is moved down and the problematic
exception test now calls bail to insure that the lock is released.
Additional fixes as suggested by Ralph Campbell <ralph.campbell@qlogic.org>:
- reduce lock scope of dma regions
- use explicit values on returns vs. automatic ret value
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve the QMH SERDES tunning on initial driver load by having the
driver go through a link state change.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently on receipt of a response message (ACKs, RDMA Response,
Atomic Responses etc.) if the SDMA completion counter is not advanced
the driver delays the completion of the WQE. In most cases this is
overly pessimistic as the response (ACK) to a previously transmitted
send implies that the send is complete. Ensure that SDMA queue is
progressed appropriately before determining if a send has delayed
completions.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under congestion resulting in eager buffer overflow attempt to send
pre-emptive NAKs if header queue entries with TID errors are generated
and a valid header is present. This prevents long timeouts and flow
restarts if a trailing set of packets are dropped due to eager
overflows. Pre-emptive NAKs are currently only supported for RDMA
writes.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current code loops during rkey/lkey validiation to isolate the MR
for the RDMA, which is expensive when the current operation is inside
a very large memory region.
This fix optimizes rkey/lkey validation routines for user memory
regions and fast memory regions. The MR entry can be isolated by
shifts/mods instead of looping. The existing loop is preserved for
phys memory regions for now.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Changing from +1 to +2 allows for better QP distribution across
receive contexts.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The upstream code was missing part of a receive/error race fix from
the internal tree. Add the missing part, which makes future merges
possible.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The basic idea is that on SusieQ, the difficult part of mapping QPN to
context is handled by the mapping registers so the generic QPN
allocation doesn't need to worry about chip specifics. For Monty and
Linda, there is no mapping table so the qpt->mask (same as
dd->qpn_mask), is used to see if the QPN to context falls within
[zero..dd->n_krcv_queues).
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For SusieQ we need to write to the interrupt timer register before
updating the header queue head with interrupt count. This is to
ensure that the timer is enabled properly and a receive available
interrupt is delivered. Otherwise this interrupt can be lost if the
receiver header/eager queues are full before the timer is enabled.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid duplicate writes to the head register as this can lead to lost
interrupts if the context goes full before the second write is done.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new SERDES tuning to aid manufacturing.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reset the list pointers after freeing the SDMA packet list. This is
done to any potential double-free cases.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement new SERDES initialization routine and improvements to signal
integrity -- disable LE1 adaptation, disable LOS after link-up, set
better SERDES parameters.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If these flags are set when the QP is transitioned to the error state,
it will wait until the flags are cleared, which may never happen if
the error transition is due to a link going down.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver was incorrectly choosing HCAs on which to allocate new user
contexts based on overall count of usable ports regardless whether the
usable port was on the currently selected HCA.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add check when setting configured contexts that the value does not
exceed the number of contexts allocated for the card. If the value
exceeds the already allocated count, set it to what is already
allocated.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the link transitions from ACTIVE_DEFERRED to ACTIVE, the driver
only sees the ACTIVE state. With this change, it will check whether
the state was already ACTIVE and if so, it will not generated IB
events and will not clear symbol error counts.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to generate receive completion entries for UD send with
immediate contains the wrong payload length. This is because when the
code to compute the payload size was moved, the value of hdrsize
didn't get moved too. The fix is to update tlen directly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBTA vol. 1 release 1.2.1 spec. says:
C14-24.2.1: If PortInfo:Portstate=Down, then a SubnSet(PortInfo) shall
make any changes it specifies to PortInfo:PortPhysicalState; any other
result is vendor-dependent.
The patch changes the error handling so that the reply says there are
invalid fields but still attempts to set fields that are in range
including PortInfo:PortPhysicalState.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to IBTA vol. 1, C11-30.1.1, a notification callback is
invoked if the CQ is armed for the next solicited completion event or
an error completion. The error case wasn't being generated correctly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support to recognize another board variation named QME7362.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The receive header queue sizes need to modified for performance
tuning. Three module parameters are added to support this.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_create_send_mad() can return ERR_PTR(-ENOMEM) here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_create_send_mad() can return ERR_PTR(-ENOMEM) here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib_free_cq_buf() should not be called under spin_lock_irq() since
it calls dma_free_coherent(), which needs irqs enabled. Fix this by
deferring the free to outside the locked region.
This was found due to the
WARN_ON(irqs_disabled());
in swiotlb_free_coherent().
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kernel warning message added in commit 58d74bb1d9 ("mlx4_core:
Workaround firmware bug in query dev cap") about mlx4 reporting the
wrong number of "blue flame registers" doesn't really help anyone, since
the firmware bug is known and fixed and the bug is pretty much harmless
to users. So just get rid of the warning.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As a first step in moving from LRO to GRO, revert commit af40da894e
("IPoIB: add LRO support"). Also eliminate the ethtool set_flags
callback which isn't needed anymore. Finally, we need to include
<linux/sched.h> directly to get the declaration of restart_syscall()
(which used to be included implicitly through <linux/inet_lro.h>).
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Re-initializing the wait object in rdma_init()/rdma_fini() causes a
timing window which can lead to a deadlock during close. Once this
deadlock hits, all RDMA activity over the T4 device will be stuck.
There's no need to re-init the wait object, so remove it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This removes unused code found by running 'make namespacecheck';
compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (390 commits)
drm/radeon/kms: disable underscan by default
drm/radeon/kms: only enable hdmi features if the monitor supports audio
drm: Restore the old_fb upon modeset failure
drm/nouveau: fix hwmon device binding
radeon: consolidate asic-specific function decls for pre-r600
vga_switcheroo: comparing too few characters in strncmp()
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
...
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Constify i2c_client where possible
i2c-algo-bit: Complain about masters which can't read SCL
i2c-algo-bit: Refactor adapter registration
i2c: Add generic I2C multiplexer using GPIO API
i2c-nforce2: Remove unnecessary cast of pci_get_drvdata
i2c-i801: Include <linux/slab.h>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (52 commits)
Blackfin: encode cpu-rev into uImage name
Blackfin: bf54x: don't ack GPIO ints when unmasking them
Blackfin: sram_free_with_lsl: do not ignore return value of sram_free
Blackfin: boards: add missing "static" to peripheral lists
Blackfin: DNP5370: new board port
Blackfin: bf518f-ezbrd: fix dsa resources
Blackfin: move "-m elf32bfin" to general LDFLAGS
Blackfin: kgdb_test: make sure to initialize num2
Blackfin: kgdb: disable preempt schedule when running single step in kgdb
Blackfin: kgdb: disable interrupt when single stepping in ADEOS
Blackfin: SMP: kgdb: apply anomaly 257 work around
Blackfin: fix building IPIPE code when XIP is enabled
Blackfin: SMP: kgdb: flush core internal write buffer before flushinv
Blackfin: sport_uart resources: remove unused secondary RX/TX pins
Blackfin: tll6527m: fix spelling in unused code (struct name)
Blackfin: bf527-ezkit: add adau1373 chip address
Blackfin: no-mpu: fix masking of small uncached dma region
Blackfin: pm: drop irq save/restore in standby and suspend to mem callback
MAINTAINERS: update Analog Devices support info
Blackfin: dpmc.h: pull in new pll.h
...
Update rtl_phy_write_fw function. The new function could
parse the complex firmware which is used by RTL8111E and later.
The new firmware may read data and do some operations, not just
do writing only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
