The access to pending_port was racy when two devices
were being attached at the same time.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If there is a receive timeout without any active
requests, we can tell the connection was idle and
ignore the timeout.
If there are active requests for which we expect
to receive a reply we close the connection.
This makes it possible to set an upper bound on
the time a usbip device may be unresponsive.
This is a workaround for the lack of heart-beat
messages in the USBIP protocol.
Extending the protocol would break compatibility
with all previous stub versions, so this seems like
the lesser evil.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also changes the event on connection close to be
VDEV_EVENT_DOWN - no functional change.
Signed-off-by: Max Vozeler <max@vozeler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There can be requests to enqueue URBs while we are shutting
down a connection.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we never received a RET_UNLINK because the TCP
connection broke the pending URBs still need to be
unlinked and given back.
Previously processes would be stuck trying to kill
the URB even after the device was detached.
Signed-off-by: Max Vozeler <max@vozeler.com>
Tested-by: Mark Wehby <MWehby@luxotticaRetail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lately, mailbox callbacks have been replaced by notifier block
call chains, this needs to be changed in the users of mailbox,
otherwise compilation will break due to missing parameters.
For this new change to work, io_mbox_msg needs to be compatible
with the notifier_call definition.
Reported-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ni_labpc driver module only requests a shared IRQ for PCI devices,
requesting a non-shared IRQ for non-PCI devices.
As this module is also used by the ni_labpc_cs module for certain
National Instruments PCMCIA cards, it also needs to request a shared IRQ
for PCMCIA devices, otherwise you get a IRQ mismatch with the CardBus
controller.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TX queues are allocated inside register_netdev.
It doesn't make any sense to stop the queue before
allocation.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IVA MMU can manage up to 4GB of address space through its page tables,
given that it's L1 is divided into 1MB sections it requires at least
16KB for its table which represents 4096 entries of 32 bits each.
Previously, only 1GB was being handled by setting the page table size
to 4KB, any virtual address beyond of the L1 size used, would fall
into memory that does not belong to L1 translation tables, leading to
unpredictable results.
So, set the L1 table size to cover the entire MMU range (4GB) whether
is meant to be used or not.
Reported-by: Felipe Contreras <felipe.contreras@nokia.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device was tested with rt2870sta by setting new_id.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Brian Ormond <brian.ormond@oit.edu>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the original code the parenthesis are in the wrong position, so the
conditions are always true.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code called input_free_device(rmi4_data->input_dev) after
input_unregister_device(rmi4_data->input_dev) and that's a double free.
This is described in the comments to input_unregister_device().
The normal way to handle this is to make input_register_device() the
last function in the probe which can fail. That way you can avoid the
call to input_unregister_device() entirely.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Off by one
Signed-off-by: Phillip Simbwa <simbwa at gmail dot com>
Signed-off-by: Vipin Mehta <vmehta@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed the call to netif_stop_queue() in netvsc_probe() as
the queue is not initialized at that point and further call
to it after queue initialization is really not necessary.
This change was prompted after an upstream change went into
2.6.37 (netif_tx_stop_queue) that now checks if netif_stop_queue
is called before register with netdev is done.
This will eliminate the warning message to the log when hv_netvsc
driver starts up.
Signed-off-by: Abhishek Kane <v-abkane@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The channel callbacks are called directly from vmbus_event_dpc
which runs in tasklet context. These callbacks need to use
GFP_ATOMIC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16701
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The block device does not create the proper symlink in sysfs because we
forgot to set up the gendisk structure properly. This patch fixes the
issue.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While building latest Linus git, I hit the following:
CC [M] drivers/staging/bcm/Qos.o
drivers/staging/bcm/Qos.c: In function ‘PruneQueue’:
drivers/staging/bcm/Qos.c:367: error: ‘struct netdev_queue’ has no member named ‘tx_dropped’
drivers/staging/bcm/Qos.c: In function ‘flush_all_queues’:
drivers/staging/bcm/Qos.c:416: error: ‘struct netdev_queue’ has no member named ‘tx_dropped’
make[5]: *** [drivers/staging/bcm/Qos.o] Error 1
make[4]: *** [drivers/staging/bcm] Error 2
make[3]: *** [drivers/staging] Error 2
As well as:
CC [M] drivers/staging/bcm/Transmit.o
drivers/staging/bcm/Transmit.c: In function ‘SetupNextSend’:
drivers/staging/bcm/Transmit.c:163: error: ‘struct netdev_queue’ has no member named ‘tx_bytes’
drivers/staging/bcm/Transmit.c:164: error: ‘struct netdev_queue’ has no member named ‘tx_packets’
make[2]: *** [drivers/staging/bcm/Transmit.o] Error 1
tx_dropped/tx_bytes_tx_packets were removed in commit 1ac9ad13. This patch
converts bcm to use net_device_stats instead of netdev_queue.
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Update workqueue usage
RDMA/nes: Fix incorrect SFP+ link status detection on driver init
RDMA/nes: Fix SFP+ link down detection issue with switch port disable
RDMA/nes: Generate IB_EVENT_PORT_ERR/PORT_ACTIVE events
RDMA/nes: Fix bonding on iw_nes
IB/srp: Test only once whether iu allocation succeeded
IB/mlx4: Handle protocol field in multicast table
RDMA: Use vzalloc() to replace vmalloc()+memset(0)
mlx4_{core, ib, en}: Fix driver when sizeof (phys_addr_t) > sizeof (long)
IB/mthca: Fix driver when sizeof (phys_addr_t) > sizeof (long)
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: fix address space warnings in ioctl_fiemap()
aio: check return value of create_workqueue()
hpfs_setattr error case avoids unlock_kernel
compat: copy missing fields in compat_statfs64 to user
compat: update comment of compat statfs syscalls
compat: remove unnecessary assignment in compat_rw_copy_check_uvector()
fs: FS_POSIX_ACL does not depend on BLOCK
fs: Remove unlikely() from fget_light()
fs: Remove unlikely() from fput_light()
fallocate should be a file operation
make the feature checks in ->fallocate future proof
staging: smbfs building fix
tidy up around finish_automount()
don't drop newmnt on error in do_add_mount()
Take the completion of automount into new helper
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: balance asic_reset functions
drm/radeon/kms: remove duplicate card_posted() functions
drm/radeon/kms: add module option for pcie gen2
drm/radeon/kms: fix typo in evergreen safe reg
drm/nouveau: fix gpu page faults triggered by plymouthd
drm/nouveau: greatly simplify mm, killing some bugs in the process
drm/nvc0: enable protection of system-use-only structures in vm
drm/nv40: initialise 0x17xx on all chipsets that have it
drm/nv40: make detection of 0x4097-ful chipsets available everywhere
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (63 commits)
ARM: PL08x: cleanup comments
Update CONFIG_MD_RAID6_PQ to CONFIG_RAID6_PQ in drivers/dma/iop-adma.c
ARM: PL08x: fix a warning
Fix dmaengine_submit() return type
dmaengine: at_hdmac: fix race while monitoring channel status
dmaengine: at_hdmac: flags located in first descriptor
dmaengine: at_hdmac: use subsys_initcall instead of module_init
dmaengine: at_hdmac: no need set ACK in new descriptor
dmaengine: at_hdmac: trivial add precision to unmapping comment
dmaengine: at_hdmac: use dma_address to program DMA hardware
pch_dma: support new device ML7213 IOH
ARM: PL08x: prevent dma_set_runtime_config() reconfiguring memcpy channels
ARM: PL08x: allow dma_set_runtime_config() to return errors
ARM: PL08x: fix locking between prepare function and submit function
ARM: PL08x: introduce 'phychan_hold' to hold on to physical channels
ARM: PL08x: put txd's on the pending list in pl08x_tx_submit()
ARM: PL08x: rename 'desc_list' as 'pend_list'
ARM: PL08x: implement unmapping of memcpy buffers
ARM: PL08x: store prep_* flags in async_tx structure
ARM: PL08x: shrink srcbus/dstbus in txd structure
...
Without this fix reloading of the driver is impossible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes the mtdpart bug which allows users reading OOB past the
end of the partition. This happens because 'part_read_oob()' allows reading
multiple OOB areas in one go, and mtdparts does not validate the OOB
length in the request.
Although there is such check in 'nand_do_read_oob()' in nand_base.c, but
it checks that we do not read past the flash chip, not the partition,
because in nand_base.c we work with the whole chip (e.g., mtd->size
in nand_base.c is the size of the whole chip). So this check cannot
be done correctly in nand_base.c and should be instead done in mtdparts.c.
This problem was reported by Jason Liu <r64343@freescale.com> and reproduced
with nandsim:
$ modprobe nandsim first_id_byte=0x20 second_id_byte=0xaa third_id_byte=0x00 \
fourth_id_byte=0x15 parts=0x400,0x400
$ modprobe nandsim mtd_oobtest.ko dev=0
$ dmesg
= snip =
mtd_oobtest: attempting to read past end of device
mtd_oobtest: an error is expected...
mtd_oobtest: error: read past end of device
= snip =
mtd_oobtest: finished with 2 errors
Reported-by: Jason Liu <liu.h.jason@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Building error for smbfs:
drivers/staging/smbfs/dir.c:286: error: static declaration of 'smbfs_dentry_operations' follows non-static declaration
drivers/staging/smbfs/proto.h:42: error: previous declaration of 'smbfs_dentry_operations' was here
drivers/staging/smbfs/dir.c:294: error: static declaration of 'smbfs_dentry_operations_case' follows non-static declaration
drivers/staging/smbfs/proto.h:41: error: previous declaration of 'smbfs_dentry_operations_case' was here
make[3]: *** [drivers/staging/smbfs/dir.o] Error 1
make[2]: *** [drivers/staging/smbfs] Error 2
make[1]: *** [drivers/staging] Error 2
make[1]: *** Waiting for unfinished jobs....
Fix it by removing static keywords
Signed-off-by: Yang Ruirui <ruirui.r.yang@tieto.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* ib_wq is added, which is used as the common workqueue for infiniband
instead of the system workqueue. All system workqueue usages
including flush_scheduled_work() callers are converted to use and
flush ib_wq.
* cancel_delayed_work() + flush_scheduled_work() converted to
cancel_delayed_work_sync().
* qib_wq is removed and ib_wq is used instead.
This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
First, we were calling mc_stop() at the top of the function
which turns off all MC (memory controller) clients,
then checking if the GPU is idle. If it was idle we
returned without re-enabling the MC clients which would
lead to a blank screen, etc. This patch checks if the
GPU is idle before calling mc_stop().
Second, if the reset failed, we were returning without
re-enabling the MC clients. This patch re-enables
the MC clients before returning regardless of whether
the reset was successful or not.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching to pcie gen2 causes problems on some
boards. Add a module option to turn it on/off.
There are gen2 compatability issues with some
motherboards it seems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33027
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix gpu page faults triggered by plymouthd
drm/nouveau: greatly simplify mm, killing some bugs in the process
drm/nvc0: enable protection of system-use-only structures in vm
drm/nv40: initialise 0x17xx on all chipsets that have it
drm/nv40: make detection of 0x4097-ful chipsets available everywhere
The switch to separate BAR and channel address spaces made the fbcon memory
address calculation incorrect on NV50+ boards, this commit fixes that.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fix these:
drivers/nfc/pn544.c: In function 'pn544_read':
drivers/nfc/pn544.c:356: warning: comparison of distinct pointer types lacks a cast
drivers/nfc/pn544.c:377: warning: comparison of distinct pointer types lacks a cast
drivers/nfc/pn544.c: In function 'pn544_write':
drivers/nfc/pn544.c:463: warning: comparison of distinct pointer types lacks a cast
drivers/nfc/pn544.c:485: warning: comparison of distinct pointer types lacks a cast
Cc: "Matti J. Aaltonen" <matti.j.aaltonen@nokia.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup the formatting of comments, remove some which don't make sense
anymore.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[fix conflict with 96a608a4]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
