When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
Cc: <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI host controllers can have both USB 3.1 and 3.0 extended speed
protocol lists. If the USB3.1 speed is parsed first and 3.0 second then
the minor revision supported will be overwritten by the 3.0 speeds and
the USB3 roothub will only show support for USB 3.0 speeds.
This was the case with a xhci controller with the supported protocol
capability listed below.
In xhci-mem.c, the USB 3.1 speed is parsed first, the min_rev of usb3_rhub
is set as 0x10. And then USB 3.0 is parsed. However, the min_rev of
usb3_rhub will be changed to 0x00. If USB 3.1 device is connected behind
this host controller, the speed of USB 3.1 device just reports 5G speed
using lsusb.
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 01 08 00 00 00 00 00 40 00 00 00 00 00 00 00 00
10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20 02 08 10 03 55 53 42 20 01 02 00 00 00 00 00 00 //USB 3.1
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40 02 08 00 03 55 53 42 20 03 06 00 00 00 00 00 00 //USB 3.0
50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 02 08 00 02 55 53 42 20 09 0E 19 00 00 00 00 00 //USB 2.0
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
This patch fixes the issue by only owerwriting the minor revision if
it is higher than the existing one.
[reword commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the xhci-plat driver
ignores it and always returns -ENODEV. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
CC: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4.11 TRB completion codes were renamed to match spec.
Completion codes for command ring stopped and endpoint stopped
were mixed, leading to failures while handling a stopped command ring.
Use the correct completion code for command ring stopped events.
Fixes: 0b7c105a04 ("usb: host: xhci: rename completion codes to match spec")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to restrict allocations to the first 16MB ISA DMA
addresses.
It is causing problems in a virtualization setup with enabled IOMMU
(x86_64). The result is that USB is not working in the VM.
CC: <stable@vger.kernel.org>
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With threaded interrupts, bottom-half handlers are called with
interrupts enabled. Therefore they can't safely use spin_lock(); they
have to use spin_lock_irqsave(). Lockdep warns about a violation
occurring in xhci_irq():
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
4.11.0-rc8-dbg+ #1 Not tainted
---------------------------------------------------------
swapper/7/0 just changed the state of lock:
(&(&ehci->lock)->rlock){-.-...}, at: [<ffffffffa0130a69>]
ehci_hrtimer_func+0x29/0xc0 [ehci_hcd]
but this lock took another, HARDIRQ-unsafe lock in the past:
(hcd_urb_list_lock){+.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(hcd_urb_list_lock);
local_irq_disable();
lock(&(&ehci->lock)->rlock);
lock(hcd_urb_list_lock);
<Interrupt>
lock(&(&ehci->lock)->rlock);
*** DEADLOCK ***
no locks held by swapper/7/0.
the shortest dependencies between 2nd lock and 1st lock:
-> (hcd_urb_list_lock){+.....} ops: 252 {
HARDIRQ-ON-W at:
__lock_acquire+0x602/0x1280
lock_acquire+0xd5/0x1c0
_raw_spin_lock+0x2f/0x40
usb_hcd_unlink_urb_from_ep+0x1b/0x60 [usbcore]
xhci_giveback_urb_in_irq.isra.45+0x70/0x1b0 [xhci_hcd]
finish_td.constprop.60+0x1d8/0x2e0 [xhci_hcd]
xhci_irq+0xdd6/0x1fa0 [xhci_hcd]
usb_hcd_irq+0x26/0x40 [usbcore]
irq_forced_thread_fn+0x2f/0x70
irq_thread+0x149/0x1d0
kthread+0x113/0x150
ret_from_fork+0x2e/0x40
This patch fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram
If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
then the assertion of the Interrupt Pending (IP) flag in Figure 30
generates a PCI Dword write. The IP flag is automatically cleared
by the completion of the PCI write.
the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI ch4.20 Scratchpad Buffers, the Scratchpad
Buffer needs to be zeroed.
...
The following operations take place to allocate
Scratchpad Buffers to the xHC:
...
b. Software clears the Scratchpad Buffer to '0'
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Denverton microserver is Atom based and need the PME and CAS quirks
as well.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't access any members of a URB after giving it back.
URB might be freed by then already.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new define for the maximum number of SuperSpeed ports instead of
a constant when allocating xHCI root hubs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure do drop the reference taken to the companion device during
resume.
Fixes: d4d75128b8 ("usb: host: ehci-platform: fix usb 1.1 device is not connected in system resume")
Cc: stable <stable@vger.kernel.org> # 4.11
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If multiple endpoints on a single device have pending IN URBs and one
endpoint times out due to NAKs (perfectly legal), select a different
endpoint URB to try.
The existing code only checked to see another device address has pending
URBs and ignores other IN endpoints on the current device address. This
leads to endpoints never getting serviced if one endpoint is using NAK as
a flow control method.
Fixes: 5d3043586d ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timeout for BULK packets was 300ms which is a long time if other
endpoints or devices are waiting for their turn. Changing it to 50ms
greatly increased the overall performance for multi-endpoint devices.
Fixes: 5d3043586d ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef is slightly wrong as it doesn't cover the xhci_priv_resume_quirk()
function, causing a harmless warning:
drivers/usb/host/xhci-plat.c:58:12: error: 'xhci_priv_resume_quirk' defined but not used [-Werror=unused-function]
static int xhci_priv_resume_quirk(struct usb_hcd *hcd)
A simpler way to do this correctly is to use __maybe_unused annotations
that let the compiler silently drop the functions when there is no
reference.
Fixes: b0c69b4bac ("usb: host: plat: Enable xHCI plat runtime PM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have sp_array to store each scratch buffer address for xHC,
it doesn't need another sp_dma_buffers array to store it.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the modern API to request MSI or MSI-X interrupts, which allows us to
get rid of the msix_entries array, as well as cleaning up the cleanup
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets resume_quirk() for R-Car controllers to re-download
the firmware in resume timing. Otherwise, if the controller's power
is down in suspend timing, the firmware in the controller goes away,
and then the controller doesn't work after resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds resume_quirk() to do platform specific process in
resume timing.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables the clk in resume timing when device_may_wakeup()
is false. Otherwise, kernel panic happens when R-Car resumes the system
from Suspend-to-RAM because the clk is disabled.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the xHCI plat runtime PM for parent device to suspend/resume
xHCI. Also call pm_runtime_forbid() in probe() function to force users
to explicitly enable runtime pm using power/control in sysfs, in case
some parent devices didn't implement runtime PM callbacks.
[set do_wakeup to true when runtime suspending -Mathias]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ff6cbf1f ("usb: xhci: Add helper function xhci_set_power_on().")
created a helper to control port power that needs to be called with
xhci->lock held and interrupts disabled.
It released the lock with spin_unlock_irqrestore using a new zero flag
variable instead of the original flag from spin_lock_irqsave.
This regression triggered a static checker warning about bogus flags, and
a null pointer dereference on armada-385.
Fix it by passing a pointer to the correct flags and using it instead
Fixes: a6ff6cbf1f ("usb: xhci: Add helper function xhci_set_power_on().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per [1] issue #4,
"The periodic EP scheduler always tries to schedule the EPs
that have large intervals (interval equal to or greater than
128 microframes) into different microframes. So it maintains
an internal counter and increments for each large interval
EP added. When the counter is greater than 128, the scheduler
rejects the new EP. So when the hub re-enumerated 128 times,
it triggers this condition."
This results in Bandwidth error when devices with periodic
endpoints (ISO/INT) having bInterval > 7 are plugged and
unplugged several times on a TUSB73x0 XHCI host.
Workaround this issue by limiting the bInterval to 7
(i.e. interval to 6) for High-speed or faster periodic endpoints.
[1] - http://www.ti.com/lit/er/sllz076/sllz076.pdf
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_trb() treats a link trb in the same way as that for
an event trb. This patch fixes this by decoding the link trb
according to the spec.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI context changes have already been traced by the trace
events. It's unnecessary to put the same message in kernel
log. This patch removes the use of xhci_dbg_ctx().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every XHCI TRB has already been traced by the trb trace events.
It is unnecessary to put the same message in kernel log. This
patch removes xhci_debug_trb().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI ring changes have already been traced by the ring trace
events. It's unnecessary to put the same messages in kernel
log. This patch removes the debugging code for a ring.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enq_updates and deq_updates were introduced in the first place
to check whether an xhci hardware is able to respond to trbs
enqueued in the ring. We now have trb tracers to trace every
single enqueue/dequeue trb. It's time to remove them and the
associated debugging code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several functions have a single user in the same file where it
is defined. There's no need to expose it anywhere else.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_dbg_ep_rings() isn't used in xhci driver anymore. Remove
it to reduce the module binary size.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch creates a new event class called xhci_log_ring, and
defines the events used for tracing the change of all kinds of
rings used by an xhci host. An xHCI ring is basically a memory
block shared between software and hardware. By tracing changes
of rings, it makes the life easier for debugging hardware or
software problems.
This info can be used, later, to print, in a human readable way,
the life cycle of an xHCI ring using the trace-cmd tool and the
appropriate plugin.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new xhci_hc_died() function that takes care of handling
pending commands and URBs if a host controller becomes unresponsive.
This addresses issues on hotpluggable xhci controllers that disappear
from the bus suddenly, often while the bus (PCI) remove function is
still being processed.
xhci_hc_died() sets a XHCI_STATUS_DYING flag to prevent new URBs and
commands or to be queued. The flag also ensures xhci_hc_died() will
give back pending commands and URBs once.
Host is considered dead if register read returns 0xffffffff, or host
fails to abort the command ring, or fails stopping an endpoint after
trying for 5 seconds.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't halt the host controller immediately when first HCD is removed as
it will cause problems if we have devices attached to the second (primary)
HCD, like a keyboard.
We've been carrying this in our Linux-as-a-bootloader environment for a
little while now. The machines all have the same TI TUSB73x0 part,
and when we kexec the devices don't come back until a system power cycle.
[minor adjustments, code comments and remove HALT check -Mathias]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's one annoyance in how xhci prints debug messages, we often
get logs with messages but it's hard to say from which device and
endpoint the message originates. Add slot_id, ep_index messages
in handle_tx_event.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format for each TRB in each control transfer stage differs. Let's make
sure we correctly pretty print these fields to avoid confusion.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With these, we can track what's happening with the HW while executing
each and every command. It will give us visibility into how the
different contexts are being modified by xHC which can bring insight
into problems while debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By extracting and exposing xhci_slot_state_string() in a header file, we
can re-use it to print Slot Context State from our tracepoints, which
can aid in tracking down problems related to command execution.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will help us figuring out which device $this URB belongs to while
debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For usb2 ports, the port test mode Test_J_State, Test_K_State,
Test_Packet, Test_SE0_NAK and Test_Force_En can be enabled
as described in usb2 spec.
USB2 test mode is a required hardware feature for system integrators
validating their hardware according to USB spec, regarding signal
strength and stuff. It is purely a hardware test feature.
Usually you need an oscilloscope and have to enable those test modes on
the hardware. This will send some specific test patterns on D+/D-. There
is no report available (in Linux itself) as it is purely externally
visible. Regular USB usage is not possible at that time.
Anyone (well access to e.g. /dev/bus/usb/001/001 provided) can use it by
sending appropriate USB_PORT_FEAT_TEST requests to the hub.
[Add better commit message by Alexander Stein -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the visability of xhci_start() so that it
can be used when enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring slot disable related code into a helper
function xhci_disable_slot() which can be used when
enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring port power on/off related code into
a helper function xhci_set_power_on() which can
be reused when enabling test mode.
[set port state to neutral before writing port power -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EINT(Event Interrupt) is a write-1-to-clear type of bit in xhci
status register. It should be cleared by writing a 1. Writing 0
to this bit has no effect.
Xhci driver tries to clear this bit by writing 0 to it. This is
not the right way to go. This patch corrects this by reading the
register first, then clearing all RO/RW1C/RsvZ bits and setting
the clearing bit, and writing back the new value at last.
Xhci spec requires that software that uses EINT shall clear it
prior to clearing any IP flags in section 5.4.2. This is the
reason why this patch is CC'ed stable as well.
[old way didn't cause any issues, skip stable, send to next -Mathias]
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB host controllers can take a significant amount of time to suspend
and resume, adding several hundred miliseconds to the kernel resume
time. Since the XHCI controller has no outside dependencies (other than
clocks, which are suspended late/resumed early), allow it to suspend and
resume asynchronously.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci needs to take care of four scenarios when asked to cancel a URB.
1 URB is not queued or already given back.
usb_hcd_check_unlink_urb() will return an error, we pass the error on
2 We fail to find xhci internal structures from urb private data such as
virtual device and endpoint ring.
Give back URB immediately, can't do anything about internal structures.
3 URB private data has valid pointers to xhci internal data, but host is
not responding.
give back URB immedately and remove the URB from the endpoint lists.
4 Everyting is working
add URB to cancel list, queue a command to stop the endpoint, after
which the URB can be turned to no-op or skipped, removed from lists,
and given back.
We failed to give back the urb in case 2 where the correct device and
endpoint pointers could not be retrieved from URB private data.
This caused a hang on Dell Inspiron 5558/0VNM2T at resume from suspend
as urb was never returned.
[ 245.270505] INFO: task rtsx_usb_ms_1:254 blocked for more than 120 seconds.
[ 245.272244] Tainted: G W 4.11.0-rc3-ARCH #2
[ 245.273983] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 245.275737] rtsx_usb_ms_1 D 0 254 2 0x00000000
[ 245.277524] Call Trace:
[ 245.279278] __schedule+0x2d3/0x8a0
[ 245.281077] schedule+0x3d/0x90
[ 245.281961] usb_kill_urb.part.3+0x6c/0xa0 [usbcore]
[ 245.282861] ? wake_atomic_t_function+0x60/0x60
[ 245.283760] usb_kill_urb+0x21/0x30 [usbcore]
[ 245.284649] usb_start_wait_urb+0xe5/0x170 [usbcore]
[ 245.285541] ? try_to_del_timer_sync+0x53/0x80
[ 245.286434] usb_bulk_msg+0xbd/0x160 [usbcore]
[ 245.287326] rtsx_usb_send_cmd+0x63/0x90 [rtsx_usb]
Reported-by: diego.viola@gmail.com
Tested-by: diego.viola@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>