We can't have preemption disabled when we call schedule(). Accept the
possibility that we'll get preempted, and it'll cost us some cacheline
bounces.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
If the user sends a fatal signal, sleeping in the TASK_KILLABLE state
permits the task to be aborted. The only wrinkle is making sure that
if/when the command completes later that it doesn't upset anything.
Handle this by setting the data pointer to 0, and checking the value
isn't NULL in the sync completion path. Eventually, bios can be cancelled
through this path too. Note that the cmdid isn't freed to prevent reuse.
We should also abort the command in the future, but this is a good start.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Because I wasn't setting driverfs_dev, the devices were showing up under
/sys/devices/virtual/block. Now they appear underneath the PCI device
which they belong to.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
In case the card has been left in a partially-configured state,
write 0 to the Enable bit.
Signed-off-by: Shane Michael Matthews <shane.matthews@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Call pci_enable_device_mem() at initialisation and pci_disable_device
at exit.
Signed-off-by: Shane Michael Matthews <shane.matthews@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Factor out most of nvme_identify() into a new nvme_submit_user_admin_command()
function. Change nvme_get_range_type() to call it and change nvme_ioctl to
realise that it's getting back all 64 ranges.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Generalise the code from nvme_identify() that sets PRP1 & PRP2 so that
it's usable for commands sent by nvme_submit_bio_queue().
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
The admin IRQ is supposed to use the pin-based (or single message MSI)
interrupt. Accomplish this by filling in entry[0]'s vector with the
INTx irq number.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Two callers with an almost identical long string of arguments, and
introducing a third soon. Time to factor out the commonalities.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Based on a patch by Mark Wu <dwu@redhat.com>
Current index allocation in virtio-blk is based on a monotonically
increasing variable "index". This means we'll run out of numbers
after a while. It also could cause confusion about the disk
name in the case of hot-plugging disks.
Change virtio-blk to use ida to allocate index, instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We want to remove the implicit everywhere presence of module.h
so fix up the people relying on that implicit presence in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting <linux/module.h> via an implicit include
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Based on a patch by Mark Wu <dwu@redhat.com>
Current index allocation in virtio-blk is based on a monotonically
increasing variable "index". This means we'll run out of numbers
after a while. It also could cause confusion about the disk
name in the case of hot-plugging disks.
Change virtio-blk to use ida to allocate index, instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
libceph: fix double-free of page vector
ceph: fix 32-bit ino numbers
libceph: force resend of osd requests if we skip an osdmap
ceph: use kernel DNS resolver
ceph: fix ceph_monc_init memory leak
ceph: let the set_layout ioctl set single traits
Revert "ceph: don't truncate dirty pages in invalidate work thread"
ceph: replace leading spaces with tabs
libceph: warn on msg allocation failures
libceph: don't complain on msgpool alloc failures
libceph: always preallocate mon connection
libceph: create messenger with client
ceph: document ioctls
ceph: implement (optional) max read size
ceph: rename rsize -> rasize
ceph: make readpages fully async
The xenbus module provides xenbus_map_ring_valloc() and
xenbus_map_ring_vfree(). Use these to map the ring pages granted by
the frontend.
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This simplifies the init/shutdown paths, and makes client->msgr available
during the rest of the setup process.
Signed-off-by: Sage Weil <sage@newdream.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
* 'stable/bug.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m/debugfs: Make type_name more obvious.
xen/p2m/debugfs: Fix potential pointer exception.
xen/enlighten: Fix compile warnings and set cx to known value.
xen/xenbus: Remove the unnecessary check.
xen/irq: If we fail during msi_capability_init return proper error code.
xen/events: Don't check the info for NULL as it is already done.
xen/events: BUG() when we can't allocate our event->irq array.
* 'stable/mmu.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Fix selfballooning and ensure it doesn't go too far
xen/gntdev: Fix sleep-inside-spinlock
xen: modify kernel mappings corresponding to granted pages
xen: add an "highmem" parameter to alloc_xenballooned_pages
xen/p2m: Use SetPagePrivate and its friends for M2P overrides.
xen/p2m: Make debug/xen/mmu/p2m visible again.
Revert "xen/debug: WARN_ON when identity PFN has no _PAGE_IOMAP flag set."
The P600 requires a small delay when changing states. Otherwise we may think
the board did not reset and we bail. This for kdump only and is particular
to the P600.
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are two windows of opportunity to cause a race when
processing a barrier request. This patch fixes this.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Currently the loop device tries to call directly into write_begin/write_end
instead of going through ->write if it can. This is a fairly nasty shortcut
as write_begin and write_end are only callbacks for the generic write code
and expect to be called with filesystem specific locks held.
This code currently causes various issues for clustered filesystems as it
doesn't take the required cluster locks, and it also causes issues for XFS
as it doesn't properly lock against the swapext ioctl as called by the
defragmentation tools. This in case causes data corruption if
defragmentation hits a busy loop device in the wrong time window, as
reported by RH QA.
The reason why we have this shortcut is that it saves a data copy when
doing a transformation on the loop device, which is the technical term
for using cryptoloop (or an XOR transformation). Given that cryptoloop
has been deprecated in favour of dm-crypt my opinion is that we should
simply drop this shortcut instead of finding complicated ways to to
introduce a formal interface for this shortcut.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The patch titled: "xen/blkback: Fix the inhibition to map pages
when discarding sector ranges." had the right idea except that
it used the wrong comparison operator. It had == instead of !=.
This fixes the bug where all (except discard) operations would
have been ignored.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The 'operation' parameters are the ones provided to the bio layer while
the req->operation are the ones passed in between the backend and
frontend. We used the wrong 'operation' value to squash the
call to map pages when processing the discard operation resulting
in an hypercall that did nothing. Lets guard against going in the
mapping function by checking for the proper operation type.
CC: Li Dongyang <lidongyang@novell.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We did not increment the amount of sectors written to disk
b/c we tested for the == WRITE which is incorrect - as the
operations are more of WRITE_FLUSH, WRITE_ODIRECT. This patch
fixes it by doing a & WRITE check.
CC: stable@kernel.org
Reported-by: Andy Burns <xen.lists@burns.me.uk>
Suggested-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We emulate the barrier requests by draining the outstanding bio's
and then sending the WRITE_FLUSH command. To drain the I/Os
we use the refcnt that is used during disconnect to wait for all
the I/Os before disconnecting from the frontend. We latch on its
value and if it reaches either the threshold for disconnect or when
there are no more outstanding I/Os, then we have drained all I/Os.
Suggested-by: Christopher Hellwig <hch@infradead.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
... though after a failed xenbus_register_frontend() all may be lost.
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Guard against issuing BLKIF_OP_WRITE_BARRIER or BLKIF_OP_FLUSH_CACHE
by checking whether we successfully negotiated with the backend.
The negotiation with the backend also sets the q->flush_flags which
fortunately for us is also used when submitting an bio to us. If
we don't support barriers or flushes it would be set to zero so
we should never end up having to deal with REQ_FLUSH | REQ_FUA.
However, other third party implementations of __make_request that
might be stacked on top of us might not be so smart, so lets fix this up.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This fixes the problem of three of those four memset()-s having
improper size arguments passed: Sizeof a pointer-typed expression
returns the size of the pointer, not that of the pointed to data.
It also reverts using kmalloc() instead of kzalloc() for the allocation
of the pending grant handles array, as that array gets fully
initialized in a subsequent loop.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch fixes belows:
1. Fix code style issue.
2. Fix incorrect functions name in comments.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When we get -EOPNOTSUPP response for a discard request, we will clear
the discard flag on the request queue so we won't attempt to send discard
requests to backend again, and this should be protected under rq->queue_lock.
However, when we setup the request queue, we pass blkif_io_lock to
blk_init_queue so rq->queue_lock is blkif_io_lock indeed, and this lock
is already taken when we are in blkif_interrpt, so remove the
spin_lock/spin_unlock when we clear the discard flag or we will end up
with deadlock here
Signed-off-by: Li Dongyang <lidongyang@novell.com>
[v1: Updated description a bit and removed comment from source]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the backend advertises 'feature-discard', then interrogate
the backend for alignment and granularity. Setup the request
queue with the appropiate values and send the discard operation
as required.
Signed-off-by: Li Dongyang <lidongyang@novell.com>
[v1: Amended commit description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
..aka ATA TRIM/SCSI UNMAP command to be passed through the frontend
and used as appropiately by the backend. We also advertise
certain granulity parameters to the frontend so it can plug them in.
If the backend is a realy device - we just end up using
'blkdev_issue_discard' while for loopback devices - we just punch
a hole in the image file.
Signed-off-by: Li Dongyang <lidongyang@novell.com>
[v1: Fixed up pr_debug and commit description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we want to use granted pages for AIO, changing the mappings of a user
vma and the corresponding p2m is not enough, we also need to update the
kernel mappings accordingly.
Currently this is only needed for pages that are created for user usages
through /dev/xen/gntdev. As in, pages that have been in use by the
kernel and use the P2M will not need this special mapping.
However there are no guarantees that in the future the kernel won't
start accessing pages through the 1:1 even for internal usage.
In order to avoid the complexity of dealing with highmem, we allocated
the pages lowmem.
We issue a HYPERVISOR_grant_table_op right away in
m2p_add_override and we remove the mappings using another
HYPERVISOR_grant_table_op in m2p_remove_override.
Considering that m2p_add_override and m2p_remove_override are called
once per page we use multicalls and hypercall batching.
Use the kmap_op pointer directly as argument to do the mapping as it is
guaranteed to be present up until the unmapping is done.
Before issuing any unmapping multicalls, we need to make sure that the
mapping has already being done, because we need the kmap->handle to be
set correctly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v1: Removed GRANT_FRAME_BIT usage]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When no floppy is found the module code can be released while a timer
function is pending or about to be executed.
CPU0 CPU1
floppy_init()
timer_softirq()
spin_lock_irq(&base->lock);
detach_timer();
spin_unlock_irq(&base->lock);
-> Interrupt
del_timer();
return -ENODEV;
module_cleanup();
<- EOI
call_timer_fn();
OOPS
Use del_timer_sync() to prevent this.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the loop device is associated (lo->lo_state == Lo_bound), it will have
a valid bdev pointed to by lo->lo_device. There is no reason to ever pass
an additional block_device pointer.
Signed-off-by: Ayan George <ayan.george@canonical.com>
Cc: Phillip Susi <psusi@cfl.rr.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The loopback driver failed to emit the change uevent when auto releasing
the device. Fixed lo_release() to pass the bdev to loop_clr_fd() so it
can emit the event.
Signed-off-by: Phillip Susi <psusi@cfl.rr.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ayan George <ayan@ayan.net>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so it
wasn't converted by commit 44c10138fd ("PCI: Change all drivers to
use pci_device->revision").
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: Chirag Kantharia <chirag.kantharia@hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/block/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a resend from the original, changing the title from PATCH to
RFC(since this is a review for commit, and I should have put that the first go around).
and also removing some of the commit's with ia64 and bash since it is significant.
let me know if I might have missed anything etc..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Automatic partition scanning can be requested individually per loop
device during its setup by setting LO_FLAGS_PARTSCAN. By default, no
partition tables are scanned.
Userspace can now always add and remove partitions from all loop
devices, regardless if the in-kernel partition scanner is enabled or
not.
The needed partition minor numbers are allocated from the extended
minors space, the main loop device numbers will continue to match the
loop minors, regardless of the number of partitions used.
# grep . /sys/class/block/loop1/loop/*
/sys/block/loop1/loop/autoclear:0
/sys/block/loop1/loop/backing_file:/home/kay/data/stuff/part.img
/sys/block/loop1/loop/offset:0
/sys/block/loop1/loop/partscan:1
/sys/block/loop1/loop/sizelimit:0
# ls -l /dev/loop*
brw-rw---- 1 root disk 7, 0 Aug 14 20:22 /dev/loop0
brw-rw---- 1 root disk 7, 1 Aug 14 20:23 /dev/loop1
brw-rw---- 1 root disk 259, 0 Aug 14 20:23 /dev/loop1p1
brw-rw---- 1 root disk 259, 1 Aug 14 20:23 /dev/loop1p2
brw-rw---- 1 root disk 7, 99 Aug 14 20:23 /dev/loop99
brw-rw---- 1 root disk 259, 2 Aug 14 20:23 /dev/loop99p1
brw-rw---- 1 root disk 259, 3 Aug 14 20:23 /dev/loop99p2
crw------T 1 root root 10, 237 Aug 14 20:22 /dev/loop-control
Cc: Karel Zak <kzak@redhat.com>
Cc: Davidlohr Bueso <dave@gnu.org>
Acked-By: Tejun Heo <tj@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch fixes belows:
1. Fix code style issue.
2. Fix incorrect functions name in comments.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When do block-attach/block-detach test with below steps, umount hangs
in the guest. Furthermore shutdown ends up being stuck when umounting file-systems.
1. start guest.
2. attach new block device by xm block-attach in Dom0.
3. mount new disk in guest.
4. execute xm block-detach to detach the block device in dom0 until timeout
5. Any request to the disk will hung.
Root cause:
This issue is caused when setting backend device's state to
'XenbusStateClosing', which sends to the frontend the XenbusStateClosing
notification. When frontend receives the notification it tries to release
the disk in blkfront_closing(), but at that moment the disk is still in use
by guest, so frontend refuses to close. Specifically it sets the disk state to
XenbusStateClosing and sends the notification to backend - when backend receives the
event, it disconnects the vbd from real device, and sets the vbd device state to
XenbusStateClosing. The backend disconnects the real device/file, and any IO
requests to the disk in guest will end up in ether, leaving disk DEAD and set to
XenbusStateClosing. When the guest wants to disconnect the disk, umount will
hang on blkif_release()->xlvbd_release_gendisk() as it is unable to send any IO
to the disk, which prevents clean system shutdown.
Solution:
Don't disconnect backend until frontend state switched to XenbusStateClosed.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Daniel Stodden <daniel.stodden@citrix.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Ian Campbell <Ian.Campbell@eu.citrix.com>
[v1: Modified description a bit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This commit adds discard support for loop devices. Discard is usually
supported by SSD and thinly provisioned devices as a method for
reclaiming unused space. This is no different than trying to reclaim
back space which is not used by the file system on the image, but it
still occupies space on the host file system.
We can do the reclamation on file system which does support hole
punching. So when discard request gets to the loop driver we can
translate that to punch a hole to the underlying file, hence reclaim
the free space.
This is very useful for trimming down the size of the image to only what
is really used by the file system on that image. Fstrim may be used for
that purpose.
It has been tested on ext4, xfs and btrfs with the image file systems
ext4, ext3, xfs and btrfs. ext4, or ext6 image on ext4 file system has
some problems but it seems that ext4 punch hole implementation is
somewhat flawed and it is unrelated to this commit.
Also this is a very good method of validating file systems punch hole
implementation.
Note that when encryption is used, discard support is disabled, because
using it might leak some information useful for possible attacker.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
ERROR: code indent should use tabs where possible
#30: FILE: drivers/block/nbd.c:578:
+^I dev_info(disk_to_dev(lo->disk), "NBD_DISCONNECT\n");$
total: 1 errors, 0 warnings, 35 lines checked
NOTE: whitespace errors detected, you may wish to use scripts/cleanpatch or
scripts/cleanfile
./patches/nbd-replace-some-printk-with-dev_warn-and-dev_info.patch has style problems, please review.
If any of these errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: WANG Cong <amwang@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is only an error, no need to use KERN_CRIT log level.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
With the frontend having Xen but the backend not, it just looks odd:
<*> Xen virtual block device support
<*> Block-device backend driver
Fix it to have the 'Xen' in front of it.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Joseph Handzik <joseph.t.handzik@beardog.cce.hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Joseph Handzik <joseph.t.handzik@beardog.cce.hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
of_device_id structures need a NULL terminating entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The buffer 'sc.cpu_mask' is a kernel buffer. If bitmap_parse is used
instead of __bitmap_parse the extra parameter that indicates a kernel
buffer is not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
LOOP_CLR_FD takes lo->lo_ctl_mutex and tries to remove the loop sysfs
files. Sysfs calls show() and waits for lo->lo_ctl_mutex. LOOP_CLR_FD
waits for show() to finish to remove the sysfs file.
cat /sys/class/block/loop0/loop/backing_file
mutex_lock_nested+0x176/0x350
? loop_attr_do_show_backing_file+0x2f/0xd0 [loop]
? loop_attr_do_show_backing_file+0x2f/0xd0 [loop]
loop_attr_do_show_backing_file+0x2f/0xd0 [loop]
dev_attr_show+0x1b/0x60
? sysfs_read_file+0x86/0x1a0
? __get_free_pages+0x12/0x50
sysfs_read_file+0xaf/0x1a0
ioctl(LOOP_CLR_FD):
wait_for_common+0x12c/0x180
? try_to_wake_up+0x2a0/0x2a0
wait_for_completion+0x18/0x20
sysfs_deactivate+0x178/0x180
? sysfs_addrm_finish+0x43/0x70
? sysfs_addrm_start+0x1d/0x20
sysfs_addrm_finish+0x43/0x70
sysfs_hash_and_remove+0x85/0xa0
sysfs_remove_group+0x59/0x100
loop_clr_fd+0x1dc/0x3f0 [loop]
lo_ioctl+0x223/0x7a0 [loop]
Instead of taking the lo_ctl_mutex from sysfs code, take the inner
lo->lo_lock, to protect the access to the backing_file data.
Thanks to Tejun for help debugging and finding a solution.
Cc: Milan Broz <mbroz@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Instead of unconditionally creating a fixed number of dead loop
devices which need to be investigated by storage handling services,
even when they are never used, we allow distros start with 0
loop devices and have losetup(8) and similar switch to the dynamic
/dev/loop-control interface instead of searching /dev/loop%i for free
devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Loop devices today have a fixed pre-allocated number of usually 8.
The number can only be changed at module init time. To find a free
device to use, /dev/loop%i needs to be scanned, and all devices need
to be opened until a free one is possibly found.
This adds a new /dev/loop-control device node, that allows to
dynamically find or allocate a free device, and to add and remove loop
devices from the running system:
LOOP_CTL_ADD adds a specific device. Arg is the number
of the device. It returns the device i or a negative
error code.
LOOP_CTL_REMOVE removes a specific device, Arg is the
number the device. It returns the device i or a negative
error code.
LOOP_CTL_GET_FREE finds the next unbound device or allocates
a new one. No arg is given. It returns the device i or a
negative error code.
The loop kernel module gets automatically loaded when
/dev/loop-control is accessed the first time. The alias
specified in the module, instructs udev to create this
'dead' device node, even when the module is not loaded.
Example:
cfd = open("/dev/loop-control", O_RDWR);
# add a new specific loop device
err = ioctl(cfd, LOOP_CTL_ADD, devnr);
# remove a specific loop device
err = ioctl(cfd, LOOP_CTL_REMOVE, devnr);
# find or allocate a free loop device to use
devnr = ioctl(cfd, LOOP_CTL_GET_FREE);
sprintf(loopname, "/dev/loop%i", devnr);
ffd = open("backing-file", O_RDWR);
lfd = open(loopname, O_RDWR);
err = ioctl(lfd, LOOP_SET_FD, ffd);
Cc: Tejun Heo <tj@kernel.org>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Replace the linked list, that keeps track of allocated devices, with an
idr index to allow a more efficient lookup of devices.
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (23 commits)
ceph: document unlocked d_parent accesses
ceph: explicitly reference rename old_dentry parent dir in request
ceph: document locking for ceph_set_dentry_offset
ceph: avoid d_parent in ceph_dentry_hash; fix ceph_encode_fh() hashing bug
ceph: protect d_parent access in ceph_d_revalidate
ceph: protect access to d_parent
ceph: handle racing calls to ceph_init_dentry
ceph: set dir complete frag after adding capability
rbd: set blk_queue request sizes to object size
ceph: set up readahead size when rsize is not passed
rbd: cancel watch request when releasing the device
ceph: ignore lease mask
ceph: fix ceph_lookup_open intent usage
ceph: only link open operations to directory unsafe list if O_CREAT|O_TRUNC
ceph: fix bad parent_inode calc in ceph_lookup_open
ceph: avoid carrying Fw cap during write into page cache
libceph: don't time out osd requests that haven't been received
ceph: report f_bfree based on kb_avail rather than diffing.
ceph: only queue capsnap if caps are dirty
ceph: fix snap writeback when racing with writes
...
This improves performance since more requests can be merged.
Reviewed-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
We were missing this cleanup, so when a device was released
the osd didn't clean up its watchers list, so following notifications
could be slow as osd needed to timeout on the client.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
* 'for-3.1/drivers' of git://git.kernel.dk/linux-block:
cciss: do not attempt to read from a write-only register
xen/blkback: Add module alias for autoloading
xen/blkback: Don't let in-flight requests defer pending ones.
bsg: fix address space warning from sparse
bsg: remove unnecessary conditional expressions
bsg: fix bsg_poll() to return POLLOUT properly
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
* 'devicetree/next' of git://git.secretlab.ca/git/linux-2.6:
dt: include linux/errno.h in linux/of_address.h
of/address: Add of_find_matching_node_by_address helper
dt: remove extra xsysace platform_driver registration
tty/serial: Add devicetree support for nVidia Tegra serial ports
dt: add empty of_property_read_u32[_array] for non-dt
dt: bindings: move SEC node under new crypto/
dt: add helper function to read u32 arrays
tty/serial: change of_serial to use new of_property_read_u32() api
dt: add 'const' for of_property_read_string parameter **out_string
dt: add helper functions to read u32 and string property values
tty: of_serial: support for 32 bit accesses
dt: document the of_serial bindings
dt/platform: allow device name to be overridden
drivers/amba: create devices from device tree
dt: add of_platform_populate() for creating device from the device tree
dt: Add default match table for bus ids
* 'stable/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Have 'passthrough' option instead of XEN_PCIDEV_BACKEND_PASS and XEN_PCIDEV_BACKEND_VPCI
xen/pciback: Remove the DEBUG option.
xen/pciback: Drop two backends, squash and cleanup some code.
xen/pciback: Print out the MSI/MSI-X (PIRQ) values
xen/pciback: Don't setup an fake IRQ handler for SR-IOV devices.
xen: rename pciback module to xen-pciback.
xen/pciback: Fine-grain the spinlocks and fix BUG: scheduling while atomic cases.
xen/pciback: Allocate IRQ handler for device that is shared with guest.
xen/pciback: Disable MSI/MSI-X when reseting a device
xen/pciback: guest SR-IOV support for PV guest
xen/pciback: Register the owner (domain) of the PCI device.
xen/pciback: Cleanup the driver based on checkpatch warnings and errors.
xen/pciback: xen pci backend driver.
xen: tmem: self-ballooning and frontswap-selfshrinking
xen: Add module alias to autoload backend drivers
xen: Populate xenbus device attributes
xen: Add __attribute__((format(printf... where appropriate
xen: prepare tmem shim to handle frontswap
xen: allow enable use of VGA console on dom0
Avoid telling users to use xvde and onwards when using xvde.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
These were intended to avoid the namespace clash when representing
emulated IDE and SCSI devices. However that seems to confuse users
more than expected (a disk defined as sda becomes xvde).
So for now go back to the scheme which does no adjustments. This
will break when mixing IDE and SCSI names in the configuration of
guests but should be by now expected.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
After commit 1c48a5c93, "dt: Eliminate
of_platform_{,un}register_driver", the xsysace driver attempts to
register two platform_drivers with the same name, which a) doesn't
work, and b) isn't necessary. This patch merges the two
platform_drivers.
Reported-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Most smartarrays will tolerate it, but some new ones don't.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Note: this is a regression caused by commit 1ddd5049
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Add xen-backend:vbd module alias to the xen-blkback module. This allows
automatic loading of the module.
Signed-off-by: Bastian Blank <waldi@debian.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Running RING_FINAL_CHECK_FOR_REQUESTS from make_response is a bad
idea. It means that in-flight I/O is essentially blocking continued
batches. This essentially kills throughput on frontends which unplug
(or even just notify) early and rightfully assume addtional requests
will be picked up on time, not synchronously.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
[v1: Rebased and fixed compile problems]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Use the compiler to verify printf formats and arguments.
Fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We used to write these with BIO_RW_BARRIER aka REQ_HARDBARRIER (unless
disabled in the configuration). The correct semantic now would be to
write with FLUSH/FUA.
For example, with activity log transactions, FUA alone is not enough, we
need the corresponding bitmap update (and all related application
updates) on stable storage as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we have an asymetrically congested network, we may send P_PING,
but due to congestion, the corresponding P_PING_ACK would time out,
and we would drop a (congested, but otherwise) healthy connection
("PingAck did not arrive in time.")
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we have a good resync rate, we will frequently update the on-disk
bitmap, which, if not accounted for as resync io, may let an otherwise
idle device appear to be "busy", and cause us to throttle resync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last commit, drbd: add missing spinlock to bitmap receive,
introduced a cond_resched_lock(), where the lock in question is taken
with irqs disabled.
As we must not schedule with IRQs disabled,
and cond_resched_lock_irq() does not exist, yet,
we re-aquire the spin_lock_irq() for each bitmap page processed in turn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
During bitmap exchange, when using the RLE bitmap compression scheme,
we have a code path that can set the whole bitmap at once.
To avoid holding spin_lock_irq() for too long, we used to lock out other
bitmap modifications during bitmap exchange by other means, and then,
knowing we have exclusive access to the bitmap, modify it without
the spinlock, and with IRQs enabled.
Since we now allow local IO to continue, potentially setting additional
bits during the bitmap receive phase, this is no longer true, and we get
uncoordinated updates of bitmap members, causing bm_set to no longer
accurately reflect the total number of set bits.
To actually see this, you'd need to have a large bitmap, use RLE bitmap
compression, and have busy IO during sync handshake and bitmap exchange.
Fix this by taking the spin_lock_irq() in this code path as well, but
calling cond_resched_lock() after each page worth of bits processed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Use hlist_entry() for io_context.cic_list.first
cfq-iosched: Remove bogus check in queue_fail path
xen/blkback: potential null dereference in error handling
xen/blkback: don't call vbd_size() if bd_disk is NULL
block: blkdev_get() should access ->bd_disk only after success
CFQ: Fix typo and remove unnecessary semicolon
block: remove unwanted semicolons
Revert "block: Remove extra discard_alignment from hd_struct."
nbd: adjust 'max_part' according to part_shift
nbd: limit module parameters to a sane value
nbd: pass MSG_* flags to kernel_recvmsg()
block: improve the bio_add_page() and bio_add_pc_page() descriptions
Jens' back-merge commit 698567f3fa ("Merge commit 'v2.6.39' into
for-2.6.40/core") was incorrectly done, and re-introduced the
DISK_EVENT_MEDIA_CHANGE lines that had been removed earlier in commits
- 9fd097b149 ("block: unexport DISK_EVENT_MEDIA_CHANGE for
legacy/fringe drivers")
- 7eec77a181 ("ide: unexport DISK_EVENT_MEDIA_CHANGE for ide-gd
and ide-cd")
because of conflicts with the "g->flags" updates near-by by commit
d4dc210f69 ("block: don't block events on excl write for non-optical
devices")
As a result, we re-introduced the hanging behavior due to infinite disk
media change reports.
Tssk, tssk, people! Don't do back-merges at all, and *definitely* don't
do them to hide merge conflicts from me - especially as I'm likely
better at merging them than you are, since I do so many merges.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
blkbk->pending_pages can be NULL here so I added a check for it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
[v1: Redid the loop a bit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
It is easier to figure out the context by reading SCSI_SENSE_BUFFERSIZE
instead of plain '96'.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Wire up the virtio_driver config_changed method to get notified about
config changes raised by the host. For now we just re-read the device
size to support online resizing of devices, but once we add more
attributes that might be changeable they could be added as well.
Note that the config_changed method is called from irq context, so
we'll have to use the workqueue infrastructure to provide us a proper
user context for our changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
x86 idle: deprecate mwait_idle() and "idle=mwait" cmdline param
x86 idle: deprecate "no-hlt" cmdline param
x86 idle APM: deprecate CONFIG_APM_CPU_IDLE
x86 idle floppy: deprecate disable_hlt()
x86 idle: EXPORT_SYMBOL(default_idle, pm_idle) only when APM demands it
x86 idle: clarify AMD erratum 400 workaround
idle governor: Avoid lock acquisition to read pm_qos before entering idle
cpuidle: menu: fixed wrapping timers at 4.294 seconds
Plan to remove floppy_disable_hlt in 2012, an ancient
workaround with comments that it should be removed.
This allows us to remove clutter and a run-time branch
from the idle code.
WARN_ONCE() on invocation until it is removed.
cc: x86@kernel.org
cc: stable@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
The 'max_part' parameter determines how many partitions are supported
on each nbd device. However the actual number can be changed to the
power of 2 minus 1 form during the module initialization as
alloc_disk() is called with (1 << part_shift) for some reason.
So adjust 'max_part' also at least for consistency with loop and brd.
It is exported via sysfs already, and a user should check this value
after module loading if [s]he wants to use that number correctly
(i.e. fdisk or something).
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Unlike kernel_sendmsg(), kernel_recvmsg() requires passing flags explicitly
via last parameter instead of struct msghdr.msg_flags. Therefore calls to
sock_xmit(lo, 0, ..., MSG_WAITALL) have not been processed properly by tcp
layer wrt. the flag. Fix it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Export 'max_loop' and 'max_part' parameters to sysfs so user can know
that how many devices are allowed and how many partitions are supported.
If 'max_loop' is 0, there is no restriction on the number of loop devices.
User can create/use the devices as many as minor numbers available. If
'max_part' is 0, it means simply the device doesn't support partitioning.
Also note that 'max_part' can be adjusted to power of 2 minus 1 form if
needed. User should check this value after the module loading if he/she
want to use that number correctly (i.e. fdisk, mknod, etc.).
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Export 'rd_nr', 'rd_size' and 'max_part' parameters to sysfs so user can
know that how many devices are allowed, how big each device is and how
many partitions are supported. If 'max_part' is 0, it means simply the
device doesn't support partitioning.
Also note that 'max_part' can be adjusted to power of 2 minus 1 form if
needed. User should check this value after the module loading if he/she
want to use that number correctly (i.e. fdisk, mknod, etc.).
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If 'rd_nr' param was not specified, 16 (can be adjusted via
CONFIG_BLK_DEV_RAM_COUNT) devices would be created by default
but comment said 1. Fix it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When finding or allocating a ram disk device, brd_probe() did not take
partition numbers into account so that it can result to a different
device. Consider following example (I set CONFIG_BLK_DEV_RAM_COUNT=4
for simplicity) :
$ sudo modprobe brd max_part=15
$ ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2011-05-25 15:41 /dev/ram0
brw-rw---- 1 root disk 1, 16 2011-05-25 15:41 /dev/ram1
brw-rw---- 1 root disk 1, 32 2011-05-25 15:41 /dev/ram2
brw-rw---- 1 root disk 1, 48 2011-05-25 15:41 /dev/ram3
$ sudo mknod /dev/ram4 b 1 64
$ sudo dd if=/dev/zero of=/dev/ram4 bs=4k count=256
256+0 records in
256+0 records out
1048576 bytes (1.0 MB) copied, 0.00215578 s, 486 MB/s
namhyung@leonhard:linux$ ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2011-05-25 15:41 /dev/ram0
brw-rw---- 1 root disk 1, 16 2011-05-25 15:41 /dev/ram1
brw-rw---- 1 root disk 1, 32 2011-05-25 15:41 /dev/ram2
brw-rw---- 1 root disk 1, 48 2011-05-25 15:41 /dev/ram3
brw-r--r-- 1 root root 1, 64 2011-05-25 15:45 /dev/ram4
brw-rw---- 1 root disk 1, 1024 2011-05-25 15:44 /dev/ram64
After this patch, /dev/ram4 - instead of /dev/ram64 - was
accessed correctly.
In addition, 'range' passed to blk_register_region() should
include all range of dev_t that RAMDISK_MAJOR can address.
It does not need to be limited by partition numbers unless
'rd_nr' param was specified.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
brd_refcnt, brd_offset, brd_sizelimit and brd_blocksize in struct
brd_device seem to be copied from struct loop_device but they're
not used anywhere. Let get rid of them.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (23 commits)
ceph: fix cap flush race reentrancy
libceph: subscribe to osdmap when cluster is full
libceph: handle new osdmap down/state change encoding
rbd: handle online resize of underlying rbd image
ceph: avoid inode lookup on nfs fh reconnect
ceph: use LOOKUPINO to make unconnected nfs fh more reliable
rbd: use snprintf for disk->disk_name
rbd: cleanup: make kfree match kmalloc
rbd: warn on update_snaps failure on notify
ceph: check return value for start_request in writepages
ceph: remove useless check
libceph: add missing breaks in addr_set_port
libceph: fix TAG_WAIT case
ceph: fix broken comparison in readdir loop
libceph: fix osdmap timestamp assignment
ceph: fix rare potential cap leak
libceph: use snprintf for unknown addrs
libceph: use snprintf for formatting object name
ceph: use snprintf for dirstat content
libceph: fix uninitialized value when no get_authorizer method is set
...
* 'for-2.6.40/drivers' of git://git.kernel.dk/linux-2.6-block: (110 commits)
loop: handle on-demand devices correctly
loop: limit 'max_part' module param to DISK_MAX_PARTS
drbd: fix warning
drbd: fix warning
drbd: Fix spelling
drbd: fix schedule in atomic
drbd: Take a more conservative approach when deciding max_bio_size
drbd: Fixed state transitions after async outdate-peer-handler returned
drbd: Disallow the peer_disk_state to be D_OUTDATED while connected
drbd: Fix for the connection problems on high latency links
drbd: fix potential activity log refcount imbalance in error path
drbd: Only downgrade the disk state in case of disk failures
drbd: fix disconnect/reconnect loop, if ping-timeout == ping-int
drbd: fix potential distributed deadlock
lru_cache.h: fix comments referring to ts_ instead of lc_
drbd: Fix for application IO with the on-io-error=pass-on policy
xen/p2m: Add EXPORT_SYMBOL_GPL to the M2P override functions.
xen/p2m/m2p/gnttab: Support GNTMAP_host_map in the M2P override.
xen/blkback: don't fail empty barrier requests
xen/blkback: fix xenbus_transaction_start() hang caused by double xenbus_transaction_end()
...
* 'for-2.6.40/core' of git://git.kernel.dk/linux-2.6-block: (40 commits)
cfq-iosched: free cic_index if cfqd allocation fails
cfq-iosched: remove unused 'group_changed' in cfq_service_tree_add()
cfq-iosched: reduce bit operations in cfq_choose_req()
cfq-iosched: algebraic simplification in cfq_prio_to_maxrq()
blk-cgroup: Initialize ioc->cgroup_changed at ioc creation time
block: move bd_set_size() above rescan_partitions() in __blkdev_get()
block: call elv_bio_merged() when merged
cfq-iosched: Make IO merge related stats per cpu
cfq-iosched: Fix a memory leak of per cpu stats for root group
backing-dev: Kill set but not used var in bdi_debug_stats_show()
block: get rid of on-stack plugging debug checks
blk-throttle: Make no throttling rule group processing lockless
blk-cgroup: Make cgroup stat reset path blkg->lock free for dispatch stats
blk-cgroup: Make 64bit per cpu stats safe on 32bit arch
blk-throttle: Make dispatch stats per cpu
blk-throttle: Free up a group only after one rcu grace period
blk-throttle: Use helper function to add root throtl group to lists
blk-throttle: Introduce a helper function to fill in device details
blk-throttle: Dynamically allocate root group
blk-cgroup: Allow sleeping while dynamically allocating a group
...
When finding or allocating a loop device, loop_probe() did not take
partition numbers into account so that it can result to a different
device. Consider following example:
$ sudo modprobe loop max_part=15
$ ls -l /dev/loop*
brw-rw---- 1 root disk 7, 0 2011-05-24 22:16 /dev/loop0
brw-rw---- 1 root disk 7, 16 2011-05-24 22:16 /dev/loop1
brw-rw---- 1 root disk 7, 32 2011-05-24 22:16 /dev/loop2
brw-rw---- 1 root disk 7, 48 2011-05-24 22:16 /dev/loop3
brw-rw---- 1 root disk 7, 64 2011-05-24 22:16 /dev/loop4
brw-rw---- 1 root disk 7, 80 2011-05-24 22:16 /dev/loop5
brw-rw---- 1 root disk 7, 96 2011-05-24 22:16 /dev/loop6
brw-rw---- 1 root disk 7, 112 2011-05-24 22:16 /dev/loop7
$ sudo mknod /dev/loop8 b 7 128
$ sudo losetup /dev/loop8 ~/temp/disk-with-3-parts.img
$ sudo losetup -a
/dev/loop128: [0805]:278201 (/home/namhyung/temp/disk-with-3-parts.img)
$ ls -l /dev/loop*
brw-rw---- 1 root disk 7, 0 2011-05-24 22:16 /dev/loop0
brw-rw---- 1 root disk 7, 16 2011-05-24 22:16 /dev/loop1
brw-rw---- 1 root disk 7, 2048 2011-05-24 22:18 /dev/loop128
brw-rw---- 1 root disk 7, 2049 2011-05-24 22:18 /dev/loop128p1
brw-rw---- 1 root disk 7, 2050 2011-05-24 22:18 /dev/loop128p2
brw-rw---- 1 root disk 7, 2051 2011-05-24 22:18 /dev/loop128p3
brw-rw---- 1 root disk 7, 32 2011-05-24 22:16 /dev/loop2
brw-rw---- 1 root disk 7, 48 2011-05-24 22:16 /dev/loop3
brw-rw---- 1 root disk 7, 64 2011-05-24 22:16 /dev/loop4
brw-rw---- 1 root disk 7, 80 2011-05-24 22:16 /dev/loop5
brw-rw---- 1 root disk 7, 96 2011-05-24 22:16 /dev/loop6
brw-rw---- 1 root disk 7, 112 2011-05-24 22:16 /dev/loop7
brw-r--r-- 1 root root 7, 128 2011-05-24 22:17 /dev/loop8
After this patch, /dev/loop8 - instead of /dev/loop128 - was
accessed correctly.
In addition, 'range' passed to blk_register_region() should
include all range of dev_t that LOOP_MAJOR can address. It does
not need to be limited by partition numbers unless 'max_loop'
param was specified.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In file included from drivers/block/drbd/drbd_main.c:54: drivers/block/drbd/drbd_int.h:1190: warning: parameter has incomplete type
Forward declarations of enums do not work.
Fix it unpleasantly by moving the prototype.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Lars Ellenberg <drbd-dev@lists.linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Found these with the help of ispell -l.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
An administrative detach used to request a state change directly to D_DISKLESS,
first suspending IO to avoid the last put_ldev() occuring from an endio handler,
potentially in irq context.
This is not enough on the receiving side (typically secondary), we may miss
some peer_req on the way to local disk, which then may do the last put_ldev()
from their drbd_peer_request_endio().
This patch makes the detach always go through the intermediate D_FAILED state.
We may consider to rename it D_DETACHING.
Alternative approach would be to create yet an other work item to be scheduled
on the worker, do the destructor work from there, and get the timing right.
manually picked commit 564040f from the drbd 8.4 branch.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The old (optimistic) implementation could shrink the bio size
on an primary device.
Shrinking the bio size on a primary device is bad. Since there
we might get BIOs with the old (bigger) size shortly after
we published the new size.
The new implementation is more conservative, and eventually
increases the max_bio_size on a primary device (which is valid).
It does so, when it knows the local limit AND the remote limit.
We cache the last seen max_bio_size of the peer in the meta
data, and rely on that, to make the operation of single
nodes more efficient.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It seems that the real cause of all the issues where that
we did not noticed in drbd_try_connect() when the other
guy closes one socket if the round trip time gets higher
than 100ms. There were that 100ms hard coded!
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It is no longer sufficient to trigger on local WRITE,
we need to check on (rq_state & RQ_IN_ACT_LOG)
before calling drbd_al_complete_io also in the error path.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If there is no replication traffic within the idle timeout
(ping-int seconds), DRBD will send a P_PING,
and adjust the timeout to ping-timeout.
If there is no P_PING_ACK received within this ping-timeout,
DRBD finally drops the connection, and tries to re-establish it.
To decide which timeout was active, we compared the current timeout
with the ping-timeout, and dropped the connection, if that was the case.
By default, ping-int is 10 seconds, ping-timeout is 500 ms.
Unfortunately, if you configure ping-timeout to be the same as ping-int,
expiry of the idle-timeout had been mistaken for a missing ping ack,
and caused an immediate reconnection attempt.
Fix:
Allow both timeouts to be equal, use a local variable
to store which timeout is active.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We limit ourselves to a configurable maximum number of pages used as
temporary bio pages.
If the configured "max_buffers" is not big enough to match the bandwidth
of the respective deployment, a distributed deadlock could be triggered
by e.g. fast online verify and heavy application IO.
TCP connections would block on congestion, because both receivers
would wait on pages to become available.
Fortunately the respective senders in this case would be able to give
back some pages already. So do that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In case a write failes on the local disk, go into D_INCONSISTENT
disk state. That causes future reads of that block to be shipped
to the peer.
Read retry remote was already in place.
Actually the documentation needs to get fixed now. Since the
application is still shielded from the error. (as long as we have
only a single disk failing) The difference to detach is that
we keep the disk. And therefore might keep all the other, still
working sectors up to date.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout. Give
them an explicit include via the following $0.02 script.
=========================================
#!/bin/bash
MANUAL=""
for i in `git grep -l 'prefetch(.*)' .` ; do
grep -q '<linux/prefetch.h>' $i
if [ $? = 0 ] ; then
continue
fi
( echo '?^#include <linux/?a'
echo '#include <linux/prefetch.h>'
echo .
echo w
echo q
) | ed -s $i > /dev/null 2>&1
if [ $? != 0 ]; then
echo $i needs manual fixup
MANUAL="$i $MANUAL"
fi
done
echo ------------------- 8\<----------------------
echo vi $MANUAL
=========================================
Signed-off-by: Paul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
non-network drivers and the fib_trie.c case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since for-2.6.40/core was forked off the 2.6.39 devel tree, we've
had churn in the core area that makes it difficult to handle
patches for eg cfq or blk-throttle. Instead of requiring that they
be based in older versions with bugs that have been fixed later
in the rc cycle, merge in 2.6.39 final.
Also fixes up conflicts in the below files.
Conflicts:
drivers/block/paride/pcd.c
drivers/cdrom/viocd.c
drivers/ide/ide-cd.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The sector number on empty barrier requests may (will?) be -1, which,
given that it's being treated as unsigned 64-bit quantity, will almost
always exceed the actual (virtual) disk's size.
Inspired by Konrad's "When writting barriers set the sector number to
zero...".
While at it also add overflow checking to the math in vbd_translate().
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't delay blk_run_queue_async
scsi: remove performance regression due to async queue run
blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
block: rescan partitions on invalidated devices on -ENOMEDIA too
cdrom: always check_disk_change() on open
block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers
The rbd driver currently splits bios when they span an object boundary.
However, the blk_end_request expects the completions to roll up the results
in block device order, and the split rbd/ceph ops can complete in any
order. This patch adds a struct rbd_req_coll to track completion of split
requests and ensures that the results are passed back up to the block layer
in order.
This fixes errors where the file system gets completion of a read operation
that spans an object boundary before the data has actually arrived. The
bug is easily reproduced with iozone with a working set larger than
available RAM.
Reported-by: Fyodor Ustinov <ufm@ufm.su>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
vbd_resize() up_read()'s xs_state.suspend_mutex twice in a row via double
xenbus_transaction_end() calls. The next down_read() in
xenbus_transaction_start() (at eg. the next resize attempt) hangs.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=618317
Acked-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the backend supports the 'feature-flush-cache' mode, use that
instead of the 'feature-barrier' support.
Currently there are three backends that support the 'feature-flush-cache'
mode: NetBSD, Solaris and Linux kernel. The 'flush' option is much
light-weight version than the 'barrier' support so lets try to use as
there are no filesystems in the kernel that use full barriers anymore.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
barrier variable is int, not long. This overflow caused another variable
override: "err" (in PV code) and "binfo" (in xenlinux code -
drivers/xen/blkfront/blkfront.c). The later caused incorrect device
flags (RO/removable etc).
Signed-off-by: Marek Marczykowski <marmarek@mimuw.edu.pl>
Acked-by: Ian Campbell <Ian.Campbell@citrix.com>
[v1: Changed title]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
drivers/block/cciss.c: In function ‘cciss_send_reset’:
drivers/block/cciss.c:2515:2: error: implicit declaration of function ‘fill_cmd’
drivers/block/cciss.c: At top level:
drivers/block/cciss.c:2531:12: error: conflicting types for ‘fill_cmd’
drivers/block/cciss.c:2534:1: note: an argument type that has a default promotion can’t match an empty parameter name list declaration
drivers/block/cciss.c:2515:18: note: previous implicit declaration of ‘fill_cmd’ was here
make[1]: *** [drivers/block/cciss.o] Error 1
make: *** [drivers/block/cciss.o] Error 2
Move fill_cmd() to above where it is first used.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is to allow number of commands reserved for use by SCSI tape drives
and medium changers to be adjusted at driver load time via the kernel
parameter cciss_tape_cmds, with a default value of 6, and a range
of 2 - 16 inclusive. Previously, the driver limited the number of
commands which could be queued to the SCSI half of the the driver
to only 2. This is to fix the problem that if you had more than
two tape drives, you couldn't, for example, erase or rewind them all
at the same time.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It causes NMIs which are undesirable at best, unsurvivable at worst.
Prefer the soft reset instead.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Just go straight to the soft-reset method instead.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
on driver load, if reset_devices is set, and the hard reset
attempts fail, try to bring up the controller to the point that
a command can be sent, and send it a soft reset command, then
after the reset undo whatever driver initialization was done to get
it to the point to take a command, and re-do it after the reset.
This is to get kdump to work on all the "non-resettable" controllers
(except 64xx controllers which can't be reset due to the potentially
shared cache module.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register. We want to
use it if it's available.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Just to reduce the messages about timeouts that appear.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When waiting for the board to become "not ready"
don't print a message saying "waiting for board to
become ready" (possibly followed by a message saying
"failed waiting for board to become not ready". Instead,
it should be "waiting for board to reset" and "failed
waiting for board to reset."
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
"
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Detect failure of controller reset by noticing if the 32 bytes of
"driver version" we store on the hardware in the config table
fail to get zeroed out. Previously we noticed if the controller
did not transition to "simple mode", but this did not detect reset
failure if the controller was already in simple mode prior to
the reset attempt (e.g. due to module parameter hpsa_simple_mode=1).
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is to ensure the board interrupts are really off when
these functions return.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We do a check for the operations right before calling dispatch_rw_block_io.
And then we do the same check in dispatch_rw_block_io. This patch
squashes those checks into the 'dispatch_rw_block_io' function.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We drop the support for 'feature-barrier' and add in the support
for the 'feature-flush-cache' if the real backend storage supports
flushing.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If one runs a simple fio request with random read/write with a
20%/80% ratio, the numbers are incredibly bad when using the CFQ scheduler.
IOmeter | | | |
64K, randrw | NOOP | CFQ | deadline |
randrwmix=80 | | | |
--------------+-------+------+----------+
blkback |103/27 |32/10 | 102/27 |
--------------+-------+------+----------+
QEMU qdisk |103/27 |102/27| 102/27 |
The problem as explained by Vivek Goyal was:
".. that difference is that sync vs async requests. In the case of
a kernel thread submitting IO, [..] all the WRITES might be being
considered as async and will go in a different queue. If you mix those
with some READS, they are always sync and will go in differnet queue.
In presence of sync queue, CFQ will idle and choke up WRITES in
an attempt to improve latencies of READs.
In case of AIO [note: this is what QEMU qdisk is doing] , [..]
it is direct IO and both READS and WRITES will be considered SYNC
and will go in a single queue and no choking of WRITES will take place."
The solution is quite simple, tack on REQ_SYNC (which is
what the WRITE_ODIRECT macro points to) and the numbers go
back up.
Suggested-by: Vivek Goyal <vgoyal@redhat.com
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We used to the plug/unplug on the submit_bio. But that means
if within a stream of WRITE, WRITE, WRITE,...,WRITE we have
one READ, it could stall the pipeline (as the 'submio_bio'
could trigger the unplug_fnc to be called and stall/sync
when doing the READ). Instead we want to move the unplugging
when the whole (or as a much as possible) ring buffer has been
processed. This also eliminates us doing plug/unplug for
each request.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In-kernel disk event polling doesn't matter for legacy/fringe drivers
and may lead to infinite event loop if ->check_events() implementation
generates events on level condition instead of edge.
Now that block layer supports suppressing exporting unlisted events,
simply leaving disk->events cleared allows these drivers to keep the
internal revalidation behavior intact while avoiding weird
interactions with userland event handler.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
