Driver for Northstar USB 3.0 PHY has been recently added under the name
phy-bcm-ns-usb3. Add binding for it into the DT files.
The only slightly tricky part is BCM47094 which uses different PHY
version and requires different compatible value.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Driver for Northstar USB 2.0 PHY was added in 4.7-rc1 by:
commit d3feb40673 ("phy: bcm-ns-usb2: new driver for USB 2.0 PHY on
Northstar").
It should be used to let EHCI platform driver init PHY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the DT node for the random number generator peripheral.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add interrupt mapping for the Switch Register Access Block. Only 12
interrupts are usable at the moment even though up to 32 are dedicated
to the SRAB.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the Switch Register Access Block which is a special piece of
hardware allowing us to perform indirect read/writes towards the
integrated BCM5301X Ethernet switch.
We also add the 4 Gigabit MAC Device Tree nodes within the brcm,bus-axi
bus node to get proper binding between the BCMA instantiated core and
the Device Tree nodes. We will need that to be able to reference
Ethernet Device Tree nodes in a future patch adding the switch ports
layout.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Controller is present on every BCM4708* board but only few devices have
serial flash attached so mark it as disabled by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There are few devices that have USB power controlled using GPIO. Linux
USB host driver (bcma-hcd) already supports this by reading vcc-gpio
from DT. Set it properly for all known devices.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Replace current device tree dummy clocks with real clock support for
Broadcom Northstar SoCs.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In the default Broadcom SDK the shared override is activated for this
cache controller, do the same in the upstream code. Data and
instruction prefetching is not activated by default for this cache
controller on the bcm53xx SoC, do it manually like it is done in the
vendor SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The driver for the PCIe controller was just added, this adds the
missing definition of the IRQ numbers to device tree. The driver itself
will be automatically detected by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the NAND flash chip description for a standard chip found
connected to this SoC. This makes use of generic Broadcom NAND driver
with the iProc interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
IRQ support for Broadcom's bus-axi driver bcma was merged into John
Linville's wireless tree and will show up in 3.19. This patch makes use
of this feature in the DTS file for the the BCM5301X SoCs. I left the
PCIe controller out, because this still needs some discussion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This has been successfully tested on Netgear R6250 and two other
development (unnamed) devices, all of them BCM4708 based.
We also got a possitive feedback from R7000 (BCM4709) tester.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
