When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.
Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This change makes sure that the ALSA buffers are cleaned if an endpoint
becomes disabled.
Before this change, if the internal ALSA buffer did overflow, the MIDI
function would stop sending MIDI to the host.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This refactor results in a cleaner state machine code and promotes
consistency, readability, and maintanability of this driver.
This refactor state machine was well tested and it is currently running in
production code and devices.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
512 is the value used by wMaxPacketSize, as specified by the USB Spec. This
makes sure this driver uses, by default, the most optimal value for IN and OUT
endpoint requests.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The new version of alloc_ep_req() already aligns the buffer size to
wMaxPacketSize on OUT endpoints.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Using usb_ep_align() makes sure that the buffer size for OUT endpoints is
always aligned with wMaxPacketSize (512 usually). This makes sure
that no buffer has the wrong size, which can cause nasty bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Length of buffers should be of type size_t whenever possible. Altough
recommended, this change has no real practical change, unless a driver has a
uses a huge or negative buffer size - it might help find these bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduce an attribute "inquiry_string" to the lun.
In some environments, e. g. BIOS boot menus, the inquiry string
is the only information about devices presented to the user. The
default string depends on the "cdrom" bit of the first lun as
well as the kernel version and allows no further customization.
So without access to the client it is not obvious which gadget is
active at a given point and what any of the available luns might
contain.
If "inquiry_string" is ignored or set to the empty string, the
old behavior is preserved.
Signed-off-by: Philipp Gesang <philipp.gesang@intra2net.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With composite gadget (ACM + NCM), USB3380 to host TCP transfer
speed dropped to 150 Mbit/s compared to 900 Mbit/s with NCM
gadget. Problem seems to be that net2280/USB3380 has only four
DMA channels and those DMA channels are allocated to first HW
endpoints. Endpoint match function was mapping endpoint names
directly, so NCM did not get DMA for bulk endpoints.
This patch changed match_ep to prefer DMA enabled hw endpoints
for bulk usb endpoints and PIO for interrupt usb endpoints.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With SuperSpeed CDC NCM gadget, net2280 would get stuck in
'handle_ep_small' function. Triggering issue requires large
TCP transfer from host to USB3380.
Patch adds check for stuck condition and prevents hard lockup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch enables SuperSpeed for NCM gadget.
Tested with USB3380 and measured TCP throughput with two Intel PCs:
udc to host: 920 Mbit/s
host to udc: 550 Mbit/s
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
There are multiple work items on the work queue, which require
ordering. Hence, an ordered workqueue has been used.
The workqueue "wq_otg" is not being used on a memory reclaim path.
Hence, WQ_MEM_RECLAIM has not been set.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling USB gadget functions configured through configfs is something
that can happen in normal use cases. Keep the existing log for this type
of event, but only as information, not as an error.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As the last known user, ie. pxa27x_udc relying on calls to
usb_gadget_xxx() was amended to use the phy notifier, remove a bit the
USB stack adherence.
Actually the driver still uses the gadget API for structures definition,
but the implementation of USB gadget specific function usb_gadget_*() is
not necessary anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the gpio based case, the status of the phy is known at start by
reading the VBus gpio.
Actually, this is a fix, as this initial state, when not set up,
prevents a gadget to answer to the enumeration phase, as there is no
notification in this case (the VBus is already high when kernel boots)
so no interrupt is triggered, and the flow is :
- gadget initializes
- gadget gets its phy-generic with a xxx_get_phy_xxx() call type
- gadget does a "set_peripheral()" call type
=> here if the otg->state is correctly filled, the proper vbus
handling will be called, and the gadget will be aware it should
answer enumeration and go forth
Without this fix, the USB cable must be removed and replugged for any
gadget relying on phy-generic and its gpio vbus handling to work.
The problem was seen on a pxa27x architecture based board on a
devicetree build.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the legacy behavior, and USB phy, upon detection a VBus signal, was
calling usb_gadget_vbus_(dis)connect().
This model doesn't work if the phy is generic and doesn't have an
adherence to the gadget API.
Instead of relying on the phy to call the gadget API, hook up the phy
notifier to report the VBus event, and upon it call the usb gadget API
ourselves.
This brings a new ordering problem, as before even if the usb_get_phy()
was failing because the UDC was probed before the phy, the phy would
call the gadget anyway, making the VBus connection event forwarded to
the gadget. Now we rely on the notifier, we have to ensure the
xxx_get_phy() does indeed work.
In order to cope with this, it is assumed that :
- for legacy platform_data machine, as the ordering cannot be ensured,
the phy must call usb_gadget_vbus_(dis)connect, such as
phy-gpio-vbus-usb.c
- for new devicetree platforms, we'll rely on the probe deferral, and
the phy can be gadget API agnostic.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These two fields will be used in a follow-up patch
to track how many entries of request's sglist we
have already processed. The reason is that if a
gadget driver sends an sglist with more entries then
we can fit in the ring, we will have to continue
processing remaining afterwards.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().
This makes the code easier to follow while making
sure that we will *always* break out of the loop.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.
While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.
This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb().
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a fix of a memory leak in a driver-registration error path, and
some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=k37B
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.8-rc2
Here is a fix of a memory leak in a driver-registration error path, and
some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: stable@vger.kernel.org # 3.15+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for v4.8-rc cycle. Again, dwc3 is
the most active driver with over 60% of this pull
request touching it.
The most important fixes are related to scatterlist
usage with dwc3. Before this pull request, we were
increment request->actual multiple times and this
would result in request->actual being larger than
request->length.
Also, if a we received a short packet midway through
processing a scatterlist, we were not clearning HWO
bit as we should.
Other than the large dwc3 scatterlist fixes, we have
a new Device ID for Intel's Kabylake silicon.
Other drivers, such as fsl_qe_udc and renesas udc,
also got a few minor fixes. Details are in shortlog.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7VYA
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc1
First set of fixes for v4.8-rc cycle. Again, dwc3 is
the most active driver with over 60% of this pull
request touching it.
The most important fixes are related to scatterlist
usage with dwc3. Before this pull request, we were
increment request->actual multiple times and this
would result in request->actual being larger than
request->length.
Also, if a we received a short packet midway through
processing a scatterlist, we were not clearning HWO
bit as we should.
Other than the large dwc3 scatterlist fixes, we have
a new Device ID for Intel's Kabylake silicon.
Other drivers, such as fsl_qe_udc and renesas udc,
also got a few minor fixes. Details are in shortlog.
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:
The LST bit should be set to 0 (isochronous
transfers normally continue until the
endpoint is removed entirely, at which time
an End Transfer command is used to stop the
transfer).
This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When rndis data transfer is in progress, some Windows7 Host PC is not
sending the GET_ENCAPSULATED_RESPONSE command for receiving the response
for the previous SEND_ENCAPSULATED_COMMAND processed.
The rndis function driver appends each response for the
SEND_ENCAPSULATED_COMMAND in a queue. As the above process got corrupted,
the Host sends a REMOTE_NDIS_RESET_MSG command to do a soft-reset.
As the rndis response queue is not freed, the previous response is sent
as a part of this REMOTE_NDIS_RESET_MSG's reset response and the Host
block any more Rndis transfers.
Hence free the rndis response queue as a part of this soft-reset so that
the correct response for REMOTE_NDIS_RESET_MSG is sent properly during the
response command.
Signed-off-by: Rajkumar Raghupathy <raghup@codeaurora.org>
Signed-off-by: Xerox Lin <xerox_lin@htc.com>
[AmitP: Cherry-picked this patch and folded other relevant
fixes from Android common kernel android-4.4]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The udc device needs to be deleted if error occurs
Fixes: 855ed04a37 ("usb: gadget: udc-core: independent registration of
gadgets and gadget drivers")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The udc->eps[] array has USB_MAX_ENDPOINTS elements so > should be >=.
Fixes: 3948f0e0c9 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 'composite_os_desc_req_prepare', if one of the memory allocations fail,
0 will be returned, which means success.
We should return -ENOMEM instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If this memory allocation fail, we will return 0, which means success.
Return -ENOMEM instead.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When reading synchronously from a non-zero endpoint, gadgetfs will
return -EFAULT even if the read succeeds, due to a bad check of the
copy_to_iter() return value.
This fix compares the return value of copy_to_iter to the amount of
bytes that was passed, and only fails if they are not the same.
Signed-off-by: Binyamin Sharet <s.binyamin@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add missing platform_set_drvdata() in dwc3_of_simple_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
