Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/usb/musb/musb_dsps.c:270:6: warning:
symbol 'dsps_musb_clear_ep_rxintr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now configure the PMIC interrupt to provide us VBUS
events. In that case we don't need to constantly poll the
status and can make it optional. This is only wired up
for the mini-B interface on beaglebone.
Note that eventually we should get also the connect status
for the host interface when the am335x internal PM coprocessor
provides us with an IRQ chip. For now, we still need to poll
for the host mode status.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dsps glue uses PLATFORM_DEVID_AUTO when creating the musb-hdrc
platform devices, this causes that the id will change in each system
depending on the order of driver probe, the order of the usb instances
defined in device-tree, or the list of enabled devices which use also
PLATFORM_DEVID_AUTO in kernel config. This id inconsistency causes
trouble in shell scripting or user guide documentation.
So switch it to static id, starting from 0 to the musb instance with
lower MMR offset. This scheme is also aligned to the naming in the SoC.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This already gets done automatically by PM runtime and we have
a separate autosuspend timeout in musb_core.c.
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer") wrongly added a call for pm_runtime_get_sync to otg_timer
that runs in softirq context. That causes a "BUG: sleeping function called
from invalid context" every time when polling the cable status:
[<c015ebb4>] (__might_sleep) from [<c0413d60>] (__pm_runtime_resume+0x9c/0xa0)
[<c0413d60>] (__pm_runtime_resume) from [<c04d0bc4>] (otg_timer+0x3c/0x254)
[<c04d0bc4>] (otg_timer) from [<c0191180>] (call_timer_fn+0xfc/0x41c)
[<c0191180>] (call_timer_fn) from [<c01915c0>] (expire_timers+0x120/0x210)
[<c01915c0>] (expire_timers) from [<c0191acc>] (run_timer_softirq+0xa4/0xdc)
[<c0191acc>] (run_timer_softirq) from [<c010168c>] (__do_softirq+0x12c/0x594)
I did not notice that as I did not have CONFIG_DEBUG_ATOMIC_SLEEP enabled.
And looks like also musb_gadget_queue() suffers from the same problem.
Let's fix the issue by using a list of delayed work then call it on
resume. Note that we want to do this only when musb core and it's
parent devices are awake, and we need to make sure the DSPS glue
timer is stopped as noted by Johan Hovold <johan@kernel.org>.
Note that we already are re-enabling the timer with mod_timer() in
dsps_musb_enable().
Later on we may be able to remove other delayed work in the musb driver
and just do it from pending_resume_work. But this should be done only
for delayed work that does not have other timing requirements beyond
just being run on resume.
Fixes: 65b3f50ed6 ("usb: musb: Add PM runtime support for MUSB DSPS
glue layer")
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now just use PM runtime autoidle support as musb core
keeps things enabled when the devctl session bit is set. And
there's no need for dsps_musb_try_idle() so let's just remove
it.
Note that as cppi41 dma is clocked by musb, this only makes
PM work for dsps glue layer if CONFIG_MUSB_PIO_ONLY=y and
cppi41.ko is unloaded. This will get fixed when cppi41.c has
PM runtime implemented.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to be polling the state when nothing is connected.
Let's change the polling logic in preparation for PM runtime
support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: undo unnecessary line leading whitespace change]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb core already exports the register read/write wrappers, so clean up
the duplication in dsps glue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set musb config->maximum_speed based on the dts setting to control musb
speed.
By default musb works in high-speed mode. Adding
maximum-speed = "full-speed";
to dts usb node will force musb to full-speed mode.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the regression caused by commit ad78c91860 ("usb: musb: dsps: just
start polling already") which causes polling the ID pin status even in
device-only mode.
Fixes: ad78c91860 ("usb: musb: dsps: just start polling already")
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set up function pointers for DMA so get closer to
being able to build in all the DMA engines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pass struct musb to tusb_dma_omap() and is_cppi_enabled(),
and add macros for the other DMA controllers. Populate the
platform specific quirks with the DMA type and use it during
runtime.
Note that platform glue layers with no custom DMA code are
tagged with MUSB_DMA_INVENTRA which may have a chance of
working. Looks like the defconfigs for these use PIO_ONLY,
so this should not break existing configs.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
fixed a USB error on dm816x, but introduced a new build error on i386
when COMPILE_TEST is set:
drivers/usb/musb/musb_dsps.c: In function ‘dsps_read_fifo32’:
drivers/usb/musb/musb_dsps.c:624:3: error: implicit declaration of function
‘readsl’ [-Werror=implicit-function-declaration]
readsl(fifo, dst, len >> 2);
Let's fix this by using ioread32_rep() instead of readsl() as that's
more portable.
Fixes: 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like dm81xx can only do 32-bit fifo reads like am35x. Let's set
up musb-dsps with a custom read_fifo function based on the compatible
flag.
Otherwise we can get the following errors when starting dhclient on a
asix USB Ethernet adapter:
asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length 0xffff003c, offset 4
While at it, let's also remove pointless cast of the driver data.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we pass our own of_node to musb_core, at least
pinctrl settings will be duplicated, meaning that
pinctrl framework will try to select default pin
state for musb_core when they were already requested
by musb-dsps.
A Warning will be printed however things will still
work.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when polling, we were using n * HZ (where n is
an integer in seconds), however HZ isn't always
correct if we're using cpufreq. A better way
is to use msecs_to_jiffies(n) (where n is now
an integer in miliseconds).
while at that, also rename poll_seconds to poll_timeout
and change its type to unsigned int.
Signed-off-by: Felipe Balbi <balbi@ti.com>
recover is a much better name than reset, considering
we don't really reset the IP, just run platform-specific
babble recovery algorithm.
while at that, also fix a typo in comment and add kdoc
for recover memeber of platform_ops.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All we have to do is, really, drop session bit
and let the session restart.
Big thanks goes to Bin Liu <b-liu@ti.com> for
inspiring this work.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We want to check if that particular bit is
set. It could very well be that bootloader
(or romcode) has fiddled with MUSB before
us which could leave other bits set in this
register.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb->int_usb already contains the correct
information for musb-core to handle babble.
In fact, this very check was just causing a
nonsensical babble interrupt storm.
With this I can get test.sh to run and, even though
all tests fail with timeout, that's still better
than locking up the system due to IRQ storm.
Also, if I remove g_zero and load g_mass_storage,
then everything works fine again.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
if reset fails, we should return a *negative*
error code, not a positive value.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We still have a combination of legacy phys and generic phys in
use so we need to support both types of phy for musb_dsps.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The value for the multipoint dts property is ignored when parsing with
of_property_read_bool, so we currently have multipoint always set as 1
even if value 0 is specified in the dts file.
Let's fix this to read the value too instead of just the property like
the binding documentation says as otherwise MUSB will fail to work
on devices with Mentor configuration that does not support multipoint.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This allows the endpoints to work when multiple MUSB glue
layers are built in.
Cc: Fabio Baltieri <fabio.baltieri@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So testing managed to configure musb in DMA mode but not load the
matching cppi41 driver for DMA. This results in
|musb-hdrc musb-hdrc.0.auto: Failed to request rx1.
|musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
|platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
which is "okay". Once the driver is loaded we re-try probing and
everyone is happy. Until then if you try suspend say
echo mem > /sys/power/state
then you go boom
|Unable to handle kernel NULL pointer dereference at virtual address 000003a4
|pgd = cf50c000
|[000003a4] *pgd=8f6a3831, *pte=00000000, *ppte=00000000
|Internal error: Oops: 17 [#1] ARM
|PC is at dsps_suspend+0x18/0x9c [musb_dsps]
|LR is at dsps_suspend+0x18/0x9c [musb_dsps]
|pc : [<bf08e268>] lr : [<bf08e268>] psr: a0000013
|sp : cbd97e00 ip : c0af4394 fp : 00000000
|r10: c0831d90 r9 : 00000002 r8 : cf6da410
|r7 : c03ba4dc r6 : bf08f224 r5 : 00000000 r4 : cbc5fcd0
|r3 : bf08e250 r2 : bf08f264 r1 : cf6da410 r0 : 00000000
|[<bf08e268>] (dsps_suspend [musb_dsps]) from [<c03ba508>] (platform_pm_suspend+0x2c/0x54)
|Code: e1a04000 e9900041 e2800010 eb4caa8e (e59053a4)
because platform_get_drvdata(glue->musb) returns a NULL pointer as long as the
device is not fully probed.
Tested-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 468bcc2a2c ("usb: musb: dsps: kill OTG timer on suspend") stopped
the timer in suspend path but forgot the re-enable it in the resume
path. This patch fixes the behaviour.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 468bcc2a2c "usb: musb: dsps: kill OTG timer on suspend"
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.
That will trigger a Data Abort exception because
we would try to access register while clock is gated.
Fix that bug.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 869c597 (usb: musb: dsps: add support for suspend and resume)
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Add sw_babble_control() logic to differentiate between transient
babble and real babble condition. Also add the SW babble control
register definitions.
Babble control register logic is implemented in the latest
revision of AM335x.
Find whether we are running on newer silicon. The babble control
register reads 0x4 by default in newer silicon as opposed to 0
in old versions of AM335x. Based on this enable the sw babble
control logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently musb_platform_reset() is only used by dsps.
In case of BABBLE interrupt for other platforms the musb_platform_reset()
is a NOP. In such situations no need to re-initialize the endpoints.
Also in the latest silicon revision of AM335x, we do have a babble recovery
mechanism without resetting the IP block. In preperation to add that support
its better to have a rest_done return for musb_platform_reset().
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 943c13971c "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For DSPS platform usb_phy_vbus(_off/_on) are NOPs.
So during musb_platform_reset() call usb_phy(_shutdown/_init)
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no reason for the register accessor functions not to adhere
to the CodingStyle rules.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
Depending on PM is not enough, because only PM_RUNTIME could be
selected. Fixes:
drivers/usb/musb/musb_dsps.c:703:12: warning: 'dsps_suspend' defined but not used [-Wunused-function]
drivers/usb/musb/musb_dsps.c:721:12: warning: 'dsps_resume' defined but not used [-Wunused-function]
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When the dsps isr sees a babble error, pass it down to the core for
fixup. Also, provide a .reset hook so the core can call us back.
A babble interrupt error occured when a USB mass storage device
("CHIPSBNK v3.3.9.1", 1e3d:2093) was disconnected from a AM33xx host.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Thomas Mellenthin <mellenthin@teufel.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When the platform initialization fails due to missing resources, it will
return -EPROBE_DEFER after dsps_musb_init() has been called.
dsps_musb_init() calls dsps_musb_dbg_init() to allocate the debugfs
nodes. At a later point in time, the probe will be retried, and
dsps_musb_dbg_init() will be called again. debugfs_create_dir() will
fail this time, as the node already exists, and so the entire device
probe will fail with -ENOMEM.
Fix this by moving debugfs_remove_recursive() from dsps_remove() to the
plaform's exit function, so it will be cleanly torn down when the probe
fails. It also feels more natural this way, as .exit is the counterpart
to .init.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
