Commit Graph

661 Commits

Author SHA1 Message Date
csonsino
c49a8682fc Bluetooth: validate BLE connection interval updates
Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.

The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.

The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.

The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.

Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06 15:33:06 +02:00
Spoorthi Ravishankar Koppad
302975cba1 Bluetooth: Add support for LE ping feature
Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.

As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.

Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06 15:29:12 +02:00
João Paulo Rechi Vita
f80c5dad7b Bluetooth: Ignore CC events not matching the last HCI command
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.

The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.

This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.

Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64)                                  0.352340
= Note: Bluetooth subsystem version 2.22                               0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0)               [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84                                 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm)                      [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14                  {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14                {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1       {0x0003} [hci0] 27.302310
        Address type: 0x06
          LE Public
          LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6   #1 [hci0] 27.302496
        Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4                 #2 [hci0] 27.419117
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7  #3 [hci0] 27.419244
        Type: Active (0x01)
        Interval: 11.250 msec (0x0012)
        Window: 11.250 msec (0x0012)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #4 [hci0] 27.420131
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2      #5 [hci0] 27.420259
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                 #6 [hci0] 27.420969
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #7 [hci0] 27.421983
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4        {0x0003} [hci0] 27.422059
      Start Discovery (0x0023) plen 1
        Status: Success (0x00)
        Address type: 0x06
          LE Public
          LE Random
@ MGMT Event: Discovering (0x0013) plen 2             {0x0003} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0002} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0001} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-05-05 19:29:04 +02:00
Jaganath Kanakkassery
cd9151b618 Bluetooth: Fix incorrect pointer arithmatic in ext_adv_report_evt
In ext_adv_report_event rssi comes before data (not after data as
in legacy adv_report_evt) so "+ 1" is not required in the ptr arithmatic
to point to next report.

Signed-off-by: Jaganath Kanakkassery <jaganath.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-04-23 19:23:20 +02:00
Gustavo A. R. Silva
16e183423f Bluetooth: hci_event: Use struct_size() helper
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, change the following form:

sizeof(*ev) + ev->num_hndl * sizeof(struct hci_comp_pkts_info)

 to :

struct_size(ev, handles, ev->num_hndl)

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-18 14:00:09 +01:00
Johan Hedberg
1629db9c75 Bluetooth: Fix unnecessary error message for HCI request completion
In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.

Avoid the misleading error and silently bail out from the function in
case the received event is a command status.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-12-19 14:37:03 +01:00
Colin Ian King
d17010bf63 Bluetooth: Remove redundant check on status
The check on status is redundant as a status has to be zero at
the point it is being checked because of a previous check and return
path via label 'unlock'.  Remove the redundant check and the deadcode
that can never be reached.

Detected by CoverityScan, CID#1471710 ("Logically dead code")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-10-14 10:31:25 +02:00
Ankit Navik
b950aa8863 Bluetooth: Add definitions and track LE resolve list modification
Add the definitions for adding entries to the LE resolve list and
removing entries from the LE resolve list. When the LE resolve list
gets changed via HCI commands make sure that the internal storage of
the resolve list entries gets updated.

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27 12:38:52 +02:00
Ankit Navik
aa12af77aa Bluetooth: Add definitions for LE set address resolution
Add the definitions for LE address resolution enable HCI commands.
When the LE address resolution enable gets changed via HCI commands
make sure that flag gets updated.

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-10 16:57:57 +02:00
YueHaibing
ad3e0b2f3c Bluetooth: remove redundant variables 'adv_set' and 'cp'
Variables 'adv_set' and 'cp'  are being assigned but are never used hence
they are redundant and can be removed.

Cleans up clang warnings:
net/bluetooth/hci_event.c:1135:29: warning: variable 'adv_set' set but not used [-Wunused-but-set-variable]
net/bluetooth/mgmt.c:3359:39: warning: variable 'cp' set but not used [-Wunused-but-set-variable]

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2018-08-06 17:06:58 +03:00
Jaganath Kanakkassery
acf0aeae43 Bluetooth: Handle ADv set terminated event
This event comes after connection complete event for incoming
connections. Since we now have different random address for
each instance, conn resp address is assigned from this event.

As of now only connection part is handled as we are not
enabling duration or max num of events while starting ext adv.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:53 +02:00
Jaganath Kanakkassery
a73c046a28 Bluetooth: Implement Set ADV set random address
This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.

Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.

This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.

< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
        Advertising handle: 0x00
        Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:53 +02:00
Jaganath Kanakkassery
45b7749f16 Bluetooth: Implement disable and removal of adv instance
If ext adv is enabled then use ext adv to disable as well.
Also remove the adv set during LE disable.

< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
        Extended advertising: Disabled (0x00)
        Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:53 +02:00
Jaganath Kanakkassery
a0fb3726ba Bluetooth: Use Set ext adv/scan rsp data if controller supports
This patch implements Set Ext Adv data and Set Ext Scan rsp data
if controller support extended advertising.

Currently the operation is set as Complete data and fragment
preference is set as no fragment

< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
        Handle: 0x00
        Operation: Complete extended advertising data (0x03)
        Fragment preference: Minimize fragmentation (0x01)
        Data length: 0x15
        16-bit Service UUIDs (complete): 2 entries
          Heart Rate (0x180d)
          Battery Service (0x180f)
        Name (complete): Test LE
        Company: Google (224)
          Data: 0102
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Data (0x08|0x0037) ncmd 1
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery
de181e887a Bluetooth: Impmlement extended adv enable
This patch basically replaces legacy adv with extended adv
based on the controller support. Currently there is no
design change. ie only one adv set will be enabled at a time.

This also adds tx_power in instance and store whatever returns
from Set_ext_parameter, use the same in adv data as well.
For instance 0 tx_power is stored in hdev only.

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0010
          Use legacy advertising PDUs: ADV_NONCONN_IND
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE 1M (0x01)
        Secondary max skip: 0x00
        Secondary PHY: LE 1M (0x01)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
      LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
        Status: Success (0x00)
        TX power (selected): 7 dbm (0x07)
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
        Extended advertising: Enabled (0x01)
        Number of sets: 1 (0x01)
        Entry 0
          Handle: 0x00
          Duration: 0 ms (0x00)
          Max ext adv events: 0
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery
6b49bcb4bc Bluetooth: Read no of adv sets during init
This patch reads the number of advertising sets in the controller
during init and save it in hdev.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery
b2cc9761f1 Bluetooth: Handle extended ADV PDU types
This patch defines the extended ADV types and handle it in ADV report.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery
0314f2867f Bluetooth: Implement Set PHY Confguration command
This enables user to set phys which will be used in all subsequent
connections. Also host will use the same in LE scanning as well.

@ MGMT Command: Set PHY Configuration (0x0045) plen 4
        Selected PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
< HCI Command: LE Set Default PHY (0x08|0x0031) plen 3
        All PHYs preference: 0x00
        TX PHYs preference: 0x07
          LE 1M
          LE 2M
          LE Coded
        RX PHYs preference: 0x07
          LE 1M
          LE 2M
          LE Coded
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Default PHY (0x08|0x0031) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 3
      Set PHY Configuration (0x0045) plen 0
        Status: Success (0x00)
@ MGMT Event: PHY Configuration Changed (0x0026) plen 4
        Selected PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery
4d94f95d30 Bluetooth: Use extended LE Connection if supported
This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.

For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.

< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
        Filter policy: White list is not used (0x00)
        Own address type: Public (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Initiating PHYs: 0x01
        Entry 0: LE 1M
          Scan interval: 60.000 msec (0x0060)
          Scan window: 60.000 msec (0x0060)
          Min connection interval: 50.00 msec (0x0028)
          Max connection interval: 70.00 msec (0x0038)
          Connection latency: 0 (0x0000)
          Supervision timeout: 420 msec (0x002a)
          Min connection length: 0.000 msec (0x0000)
          Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
      LE Extended Create Connection (0x08|0x0043) ncmd 2
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
      LE Enhanced Connection Complete (0x0a)
        Status: Success (0x00)
        Handle: 3585
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Connection interval: 67.50 msec (0x0036)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
        LE Address: DB:7E:2E:1D:85:E8 (Static)
        Flags: 0x00000000
        Data length: 27
        Name (complete): Designer Mouse
        Appearance: Mouse (0x03c2)
        Flags: 0x05
          LE Limited Discoverable Mode
          BR/EDR Not Supported
        16-bit Service UUIDs (complete): 1 entry
          Human Interface Device (0x1812)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:54:03 +02:00
Jaganath Kanakkassery
d12fb05643 Bluetooth: Introduce helpers for le conn status and complete
This is done so that the helpers can be used for extended conn
implementation which will be done in subsequent patch.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:45:56 +02:00
Jaganath Kanakkassery
c215e9397b Bluetooth: Process extended ADV report event
This patch enables Extended ADV report event if extended scanning
is supported in the controller and process the same.

The new features are not handled and for now its as good as
legacy ADV report.

> HCI Event: LE Meta Event (0x3e) plen 53
      LE Extended Advertising Report (0x0d)
        Num reports: 1
        Entry 0
          Event type: 0x0013
            Props: 0x0013
              Connectable
              Scannable
              Use legacy advertising PDUs
            Data status: Complete
          Legacy PDU Type: ADV_IND (0x0013)
          Address type: Random (0x01)
          Address: DB:7E:2E:1A:85:E8 (Static)
          Primary PHY: LE 1M
          Secondary PHY: LE 1M
          SID: 0x00
          TX power: 0 dBm
          RSSI: -90 dBm (0xa6)
          Periodic advertising invteral: 0.00 msec (0x0000)
          Direct address type: Public (0x00)
          Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
          Data length: 0x1b
        0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65  ..Designer Mouse
        03 19 c2 03 02 01 05 03 03 12 18                 ...........

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:43:34 +02:00
Jaganath Kanakkassery
a2344b9e3a Bluetooth: Use extended scanning if controller supports
This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.

The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:41:17 +02:00
Jaganath Kanakkassery
3baef81046 Bluetooth: Introduce helpers for LE set scan start and complete
Introduce a helper hci_req_start_scan() which starts an LE
scan and call it from passive_Scan() and active_scan().
There is not functionality change in this patch.

This is basically done to enable extended scanning if the
controller supports which will be done in the subsequent
patch

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:41:17 +02:00
Ankit Navik
545f2596b9 Bluetooth: Add HCI command for clear Resolv list
Check for Resolv list supported by controller. So check the supported
commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 28.919131
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 28.920016
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 28.920164
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 28.920873
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 28.921109
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 28.922016
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0  #61 [hci0] 28.922166
> HCI Event: Command Complete (0x0e) plen 4                #62 [hci0] 28.922872
      LE Clear Resolving List (0x08|0x0029) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #63 [hci0] 28.923117
> HCI Event: Command Complete (0x0e) plen 12               #64 [hci0] 28.924030
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 12:40:08 +02:00
Ankit Navik
cfdb0c2d09 Bluetooth: Store Resolv list size
When the controller supports the Read LE Resolv List size feature, the
maximum list size are read and now stored.

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 17.979791
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 17.980629
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 17.980786
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 17.981627
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #59 [hci0] 17.981786
> HCI Event: Command Complete (0x0e) plen 12               #60 [hci0] 17.982636
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 12:40:08 +02:00
Chriz Chow
ee6493462f Bluetooth: Prevent buffer overflow for large advertisement data
There are some controllers sending out advertising data with illegal
length value which is longer than HCI_MAX_AD_LENGTH, causing the
buffer last_adv_data overflows. To avoid these controllers from
overflowing the buffer, we do not process the advertisement data
if its length is incorrect.

Signed-off-by: Chriz Chow <chriz.chow@aminocom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18 06:37:51 +02:00
Szymon Janc
082f2300cf Bluetooth: Fix connection if directed advertising and privacy is used
Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.

This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C

Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6          #11350 [hci0] 84680.231216
        Address: 56:BC:E8:24:11:68 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4                        #11351 [hci0] 84680.246022
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7         #11352 [hci0] 84680.246417
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                        #11353 [hci0] 84680.248854
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11354 [hci0] 84680.249466
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                        #11355 [hci0] 84680.253222
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                          #11356 [hci0] 84680.458387
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
        RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11357 [hci0] 84680.458737
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                        #11358 [hci0] 84680.469982
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25          #11359 [hci0] 84680.470444
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                          #11360 [hci0] 84680.474971
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0    #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4                        #11362 [hci0] 84682.551014
      LE Create Connection Cancel (0x08|0x000e) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                          #11363 [hci0] 84682.551074
      LE Connection Complete (0x01)
        Status: Unknown Connection Identifier (0x02)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Connection interval: 0.00 msec (0x0000)
        Connection latency: 0 (0x0000)
        Supervision timeout: 0 msec (0x0000)
        Master clock accuracy: 0x00

After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7    #210 [hci0] 667.152459
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                   #211 [hci0] 667.153613
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2        #212 [hci0] 667.153704
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                   #213 [hci0] 667.154584
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                     #214 [hci0] 667.182619
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
        RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2       #215 [hci0] 667.182704
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                  #216 [hci0] 667.183599
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6    #217 [hci0] 667.183645
        Address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4                  #218 [hci0] 667.184590
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25    #219 [hci0] 667.184613
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                    #220 [hci0] 667.186558
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                    #221 [hci0] 667.485824
      LE Connection Complete (0x01)
        Status: Success (0x00)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13          {0x0002} [hci0] 667.485996
        LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
        Flags: 0x00000000
        Data length: 0

Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2018-04-03 16:12:56 +02:00
Marcel Holtmann
2064ee332e Bluetooth: Use bt_dev_err and bt_dev_info when possible
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-30 12:25:45 +02:00
Colin Ian King
27d1c469a5 Bluetooth: fix spelling mistake: "advetising" -> "advertising"
trivial fix to spelling mistake in BT_ERR_RATELIMITED error message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-02-16 17:39:35 +01:00
Szymon Janc
160b925163 Bluetooth: Add Authentication Failed reason to Disconnected Mgmt event
If link is disconnected due to Authentication Failure (PIN or Key
Missing status) userspace will be notified about this with proper error
code. Many LE profiles define "PIN or Key Missing" status as indication
of remote lost bond so this allows userspace to take action on this.

@ Device Connected: 88:63:DF:88:0E:83 (1) flags 0x0000
        02 01 1a 05 03 0a 18 0d 18 0b 09 48 65 61 72 74  ...........Heart
        20 52 61 74 65                                    Rate
> HCI Event: Command Status (0x0f) plen 4
      LE Read Remote Used Features (0x08|0x0016) ncmd 1
        Status: Success (0x00)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
      ATT: Read By Group Type Request (0x10) len 6
        Handle range: 0x0001-0xffff
        Attribute group type: Primary Service (0x2800)
> HCI Event: LE Meta Event (0x3e) plen 12
      LE Read Remote Used Features (0x04)
        Status: Success (0x00)
        Handle: 3585
        Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
          LE Encryption
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
        Handle: 3585
        Random number: 0x0000000000000000
        Encrypted diversifier: 0x0000
        Long term key: 26201cd479a0921b6f949f0b1fa8dc82
> HCI Event: Command Status (0x0f) plen 4
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Encryption Change (0x08) plen 4
        Status: PIN or Key Missing (0x06)
        Handle: 3585
        Encryption: Disabled (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 3585
        Reason: Authentication Failure (0x05)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 3585
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: 88:63:DF:88:0E:83 (1) reason 4

@ Device Connected: C4:43:8F:A3:4D:83 (0) flags 0x0000
        08 09 4e 65 78 75 73 20 35                       ..Nexus 5
> HCI Event: Command Status (0x0f) plen 4
      Authentication Requested (0x01|0x0011) ncmd 1
        Status: Success (0x00)
> HCI Event: Link Key Request (0x17) plen 6
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
        Link key: 080812e4aa97a863d11826f71f65a933
> HCI Event: Command Complete (0x0e) plen 10
      Link Key Request Reply (0x01|0x000b) ncmd 1
        Status: Success (0x00)
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
> HCI Event: Auth Complete (0x06) plen 3
        Status: PIN or Key Missing (0x06)
        Handle: 75
@ Authentication Failed: C4:43:8F:A3:4D:83 (0) status 0x05
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 75
        Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 75
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: C4:43:8F:A3:4D:83 (0) reason 4

Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2016-07-13 08:32:12 +03:00
Marcel Holtmann
ca8bee5dde Bluetooth: Rename HCI_BREDR into HCI_PRIMARY
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2016-07-09 21:37:13 +03:00
Johan Hedberg
56b40fbf61 Bluetooth: Ignore unknown advertising packet types
In case of buggy controllers send advertising packet types that we
don't know of we should simply ignore them instead of trying to react
to them in some (potentially wrong) way.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-04-08 18:51:44 +02:00
Johan Hedberg
0d3b7f64c8 Bluetooth: Change eir_has_data_type() to more generic eir_get_data()
To make the EIR parsing helper more general purpose, make it return
the found data and its length rather than just saying whether the data
was present or not.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-05 17:02:49 +01:00
Johan Hedberg
f22525700b Bluetooth: Move advertising instance management to hci_request.c
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:47 +01:00
Johan Hedberg
01b1cb87d3 Bluetooth: Run page scan updates through hdev->req_workqueue
Since Add/Remove Device perform the page scan updates independently
from the HCI command completion we've introduced a potential race when
multiple mgmt commands are queued. Doing the page scan updates through
the req_workqueue ensures that the state changes are performed in a
race-free manner.

At the same time, to make the request helper more widely usable,
extend it to also cover Inquiry Scan changes since those are behind
the same HCI command. This is also reflected in the new name of the
API as well as the work struct name.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:47 +01:00
Marcel Holtmann
242c0ebd37 Bluetooth: Rename bt_cb()->req into bt_cb()->hci
The SKB context buffer for HCI request is really not just for requests,
information in their are preserved for the whole HCI layer. So it makes
more sense to actually rename it into bt_cb()->hci and also call it then
struct hci_ctrl.

In addition that allows moving the decoded opcode for outgoing packets
into that struct. So far it was just consuming valuable space from the
main shared items. And opcode are not valid for L2CAP packets.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-26 08:21:03 +02:00
Johan Hedberg
9d4c1cc15b Bluetooth: Use hci_conn_hash_lookup_le() when possible
Use the new hci_conn_hash_lookup_le() API to look up LE connections.
This way we're guaranteed exact matches that also take into account
the address type.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21 18:38:22 +02:00
David S. Miller
26440c835f Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/usb/asix_common.c
	net/ipv4/inet_connection_sock.c
	net/switchdev/switchdev.c

In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.

The other two conflicts were overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-20 06:08:27 -07:00
Johan Hedberg
49c509220d Bluetooth: Fix LE reconnection logic
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.

To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-16 09:24:41 +02:00
Jakub Pawlowski
168b8a25c0 Bluetooth: Fix double scan updates
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.

This patch makes sure that unnecessary scan disable/enable commands
are not issued.

When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.

hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.

When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-16 09:24:41 +02:00
Szymon Janc
6818375e97 Bluetooth: Fix reporting incorrect EIR in device found mgmt event
Some remote devices (ie Gigaset G-Tag) misbehave with ADV data length.
This can lead to incorrect EIR format in device found event when
ADV_DATA and SCAN_RSP are merged (terminator field before SCAN_RSP
part).

Fix this by inspecting ADV_DATA and correct its length if terminator
is found.

> HCI Event: LE Meta Event (0x3e) plen 42              [hci0] 32.172182
      LE Advertising Report (0x02)
        Num reports: 1
        Event type: Connectable undirected - ADV_IND (0x00)
        Address type: Public (0x00)
        Address: 7C:2F:80:94:97:5A (Gigaset Communications GmbH)
        Data length: 30
        Flags: 0x06
          LE General Discoverable Mode
          BR/EDR Not Supported
        Company: Gigaset Communications GmbH (384)
          Data: 021512348094975abbc5
        16-bit Service UUIDs (partial): 1 entry
          Battery Service (0x180f)
        RSSI: -65 dBm (0xbf)
> HCI Event: LE Meta Event (0x3e) plen 27              [hci0] 32.172191
      LE Advertising Report (0x02)
        Num reports: 1
        Event type: Scan response - SCAN_RSP (0x04)
        Address type: Public (0x00)
        Address: 7C:2F:80:94:97:5A (Gigaset Communications GmbH)
        Data length: 15
        Name (complete): Gigaset G-tag
        RSSI: -59 dBm (0xc5)

Note "Data length: 30" in ADV_DATA which results in 9 extra zero bytes
after Battery Service UUID. Terminator field present in the middle of
EIR in Device Found event resulted in userspace stop parsing EIR and
skipping device name.

@ Device Found: 7C:2F:80:94:97:5A (1) rssi -59 flags 0x0000
      02 01 06 0d ff 80 01 02 15 12 34 80 94 97 5a bb  ..........4...Z.
      c5 03 02 0f 18 00 00 00 00 00 00 00 00 00 0e 09  ................
      47 69 67 61 73 65 74 20 47 2d 74 61 67           Gigaset G-tag

With this fix EIR with merged ADV_DATA and SCAN_RSP in device found
event is properly formatted:

@ Device Found: 7C:2F:80:94:97:5A (1) rssi -59 flags 0x0000
      02 01 06 0d ff 80 01 02 15 12 34 80 94 97 5a bb  ..........4...Z.
      c5 03 02 0f 18 0e 09 47 69 67 61 73 65 74 20 47  .......Gigaset G
      2d 74 61 67                                      -tag

Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-18 09:53:20 +02:00
Kuba Pawlak
618353b1f3 Bluetooth: Fix SCO link type handling on connection complete
Synchronous connections are initially created with type eSCO.
Link manager may reject proposed link parameters, which triggers
connection setup retry with a different set. Link type embedded
in responses should be disregarded until Synchronous Connect Complete
returns Success (0x00). Current code updates link type every time
which creates an issue when link type changes to SCO and back to eSCO
on further attepts.

Issue happens with BlackBerry 9100 and 9700 with Intel WilkinsPeak
on third connection setup attept

2015-05-18 01:27:57.332242 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
    handle 256 voice setting 0x0060 ptype 0x0380
2015-05-18 01:27:57.333604 > HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2015-05-18 01:27:57.334614 > HCI Event: Synchronous Connect Complete (0x2c) plen 17
    status 0x1a handle 0 bdaddr 30:7C:30:B3:A8:86 type SCO
    Error: Unsupported Remote Feature / Unsupported LMP Feature
2015-05-18 01:27:57.334895 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
    handle 256 voice setting 0x0060 ptype 0x0380
2015-05-18 01:27:57.335601 > HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2015-05-18 01:27:57.336610 > HCI Event: Synchronous Connect Complete (0x2c) plen 17
    status 0x1a handle 0 bdaddr 30:7C:30:B3:A8:86 type SCO
    Error: Unsupported Remote Feature / Unsupported LMP Feature
2015-05-18 01:27:57.336685 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
    handle 256 voice setting 0x0060 ptype 0x03c8
2015-05-18 01:27:57.337603 > HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2015-05-18 01:27:57.342608 > HCI Event: Max Slots Change (0x1b) plen 3
    handle 256 slots 1
2015-05-18 01:27:57.377631 > HCI Event: Synchronous Connect Complete (0x2c) plen 17
    status 0x00 handle 257 bdaddr 30:7C:30:B3:A8:86 type eSCO
    Air mode: CVSD

Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-28 21:03:00 +02:00
Jakub Pawlowski
28a667c9c2 Bluetooth: advertisement handling in new connect procedure
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This path makes sure that after advertisement is received from device that
we try to connect to, it is properly handled in check_pending_le_conn and
trigger connect attempt.

It also modifies hci_le_connect to make sure that connect attempt will be
properly continued.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-10 21:36:13 +02:00
Jakub Pawlowski
e7d9ab731a Bluetooth: add hci_lookup_le_connect
This patch adds hci_lookup_le_connect method, that will be used to check
wether outgoing le connection attempt is in progress.

Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-10 21:36:13 +02:00
Arron Wang
df9b89c7e4 Bluetooth: Move create/accept phy link completed callback to amp.c
To avoid amp module hooks from hci_event.c

Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30 13:37:22 +02:00
Arron Wang
b3d3914006 Bluetooth: Move amp assoc read/write completed callback to amp.c
To avoid amp module hooks from hci_event.c

Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30 13:37:22 +02:00
Arron Wang
839278823c Bluetooth: Move get info completed callback to a2mp.c
To avoid a2mp module hooks from hci_event.c and send
getinfo response operation only required by a2mp module,
we can move this callback to a2mp.c

Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30 13:37:22 +02:00
Arron Wang
a77a6a14e5 Bluetooth: Move high speed specific event under BT_HS option
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30 13:31:59 +02:00
Johan Hedberg
5d667ef6e0 Bluetooth: Remove redundant check for ACL_LINK
The encryption key size is read only for BR/EDR (ACL_LINK) connections
so there's no need to check for it in the read_enc_key_size_complete()
callback.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-06-12 12:07:20 +02:00
Johan Hedberg
821f376668 Bluetooth: Read encryption key size for BR/EDR connections
Since Bluetooth 3.0 there's a HCI command available for reading the
encryption key size of an BR/EDR connection. This information is
essential e.g. for generating an LTK using SMP over BR/EDR, so store
it as part of struct hci_conn.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-06-12 11:38:45 +02:00