In ieee80211_xmit_fast(), 'info' is initialized to point to the skb
that's passed in, but that skb may later be replaced by a clone (if
it was shared), leading to an invalid pointer.
This can lead to use-after-free and also later crashes since the
real SKB's info->hw_queue doesn't get initialized properly.
Fix this by assigning info only later, when it's needed, after the
skb replacement (may have) happened.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
A-MSDU aggregation alters the QoS header after a frame has been
enqueued, so it needs to be ready before enqueue and not overwritten
again afterwards
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to ieee80211_txq_enqueue overwrites the vif pointer with the
codel enqueue time, so setting it just before that call makes no sense.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sequence number counter is used to derive the starting sequence
number. Since that counter is updated on tx dequeue, the A-MPDU flag
needs to be up to date at the tme of dequeue as well.
This patch prevents sending more A-MPDU frames after the session has
been terminated and also ensures that aggregation starts right after the
session has been established
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to IEEE 802.11-2012 section 8.3.2 table 8-19, the outer SA/DA
of A-MSDU frames need to be changed depending on FromDS/ToDS values.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use ether_addr_copy and add alignment annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds filtering for multicast data packets on AP_VLAN
interfaces that have no authorized station connected and changes
filtering on AP interfaces to not count stations assigned to
AP_VLAN interfaces.
This saves airtime and avoids waking up other stations currently
authorized in this BSS. When using WPA, the packets dropped could
not be decrypted by any station.
The behaviour when there are no AP_VLAN interfaces is left unchanged.
When there are AP_VLAN interfaces, this patch
1. adds filtering multicast data packets sent on AP_VLAN interfaces
that have no authorized station connected.
No filtering happens on 4addr AP_VLAN interfaces.
2. makes filtering of multicast data packets sent on AP interfaces
depend on the number of authorized stations in this bss not
assigned to an AP_VLAN interface.
Therefore, a new num_mcast_sta counter is added for AP_VLAN interfaces.
The existing one for AP interfaces is altered to not track stations
assigned to an AP_VLAN interface.
The new counter is exposed in debugfs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[reformat commit message a bit, unline ieee80211_vif_{inc,dec}_num_mcast]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resolve the merge conflict between Felix's/my and Toke's patches
coming into the tree through net and mac80211-next respectively.
Most of Felix's changes go away due to Toke's new infrastructure
work, my patch changes to "goto begin" (the label wasn't there
before) instead of returning NULL so flow control towards drivers
is preserved better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TXQ intermediate queues can cause packet reordering when more than
one flow is active to a single station. Since some of the wifi-specific
packet handling (notably sequence number and encryption handling) is
sensitive to re-ordering, things break if they are applied before the
TXQ.
This splits up the TX handlers and fast_xmit logic into two parts: An
early part and a late part. The former is applied before TXQ enqueue,
and the latter after dequeue. The non-TXQ path just applies both parts
at once.
Because fragments shouldn't be split up or reordered, the fragmentation
handler is run after dequeue. Any fragments are then kept in the TXQ and
on subsequent dequeues they take precedence over dequeueing from the FQ
structure.
This approach avoids having to scatter special cases all over the place
for when TXQ is enabled, at the cost of making the fast_xmit and TX
handler code slightly more complex.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[fix a few code-style nits, make ieee80211_xmit_fast_finish void,
remove a useless txq->sta check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Small devices can run out of memory from queueing too many packets. If
VHT is not supported by the PHY, having more than 4 MBytes of total
queue in the TXQ intermediate queues is not needed, and so we can safely
limit the memory usage in these cases and avoid OOM.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TXQ path restructure requires ieee80211_tx_dequeue() to call TX
handlers and parts of the xmit_fast path. Move the function to later in
tx.c in preparation for this.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The A-MSDU TX code (within TXQs) didn't always check the return value
of skb_linearize() properly, resulting in potentially passing a frag-
list SKB down to the driver even when it said it can't handle it. Fix
that.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
smatch pointed out that the second check of "tdls_auth" was
pointless since if it was true, we returned from the function
already. We can further simplify the code by moving the first
check (if it's a TDLS peer at all) into the outer if, to only
handle that inside. This simplifies the control flow here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the 'aqm' stats in mac80211 only keeps overlimit drop stats,
not CoDel stats. This moves the CoDel stats into the txqi structure to
keep them per txq in order to show them in debugfs.
In addition, the aqm debugfs output is restructured by splitting it up
into three files: One global per phy, one per netdev and one per
station, in the appropriate directories. The files are all called aqm,
and are only created if the driver supports the wake_tx_queue op (rather
than emitting an error on open as previously).
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using intermediate queues, sequence number allocation is deferred
until dequeue. This doesn't work for PS response frames, which bypass
those queues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Insert the u32 monitor flags variable in a new structure
that represents a monitor interface.
This will allow to add more configuration variables to
that structure which will happen in an upcoming change.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the code only touches the MAC headers, the offsets to the
network/transport headers remain the same throughout this function.
Remove pointless pieces of code that try to 'preserve' them.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There is no other limit other than a global
packet count limit when using software queuing.
This means a single flow queue can grow insanely
long. This is particularly bad for TCP congestion
algorithms which requires a little more
sophisticated frame dropping scheme than a mere
headdrop on limit overflow.
Hence apply (a slighly modified, to fit the knobs)
CoDel5 on flow queues. This improves TCP
convergence and stability when combined with
wireless driver which keeps its own tx queue/fifo
at a minimum fill level for given link conditions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requires software tx queueing and fast-xmit support. For good
performance, drivers need frag_list support as well. This avoids the
need for copying data of aggregated frames. Running without it is only
supported for debugging purposes.
To avoid performance and packet size issues, the rate control module or
driver needs to limit the maximum A-MSDU size by setting
max_rc_amsdu_len in struct ieee80211_sta.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix locking issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we enqueued the frame that was supposed to be sent
during the SP, and that frame may very well cary the
IEEE80211_TX_STATUS_EOSP bit, we may never close the SP
(WLAN_STA_SP will never be cleared). If that happens, we
will not open any new SP and will never respond to any poll
frame from the client.
Clear WLAN_STA_SP manually if a frame that was polled during
the SP is queued because of a starting A-MPDU session. The
client may not see the EOSP bit, but it will at least be
able to poll new frames in another SP.
Reported-by: Alesya Shapira <alesya.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove erroneous comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Frames that are sent between
ampdu_action(IEEE80211_AMPDU_TX_START) and the move to the
HT_AGG_STATE_OPERATIONAL state are buffered.
If we try to start an A-MPDU session while the peer is
sleeping and polling frames with U-APSD, we may have frames
that will be buffered by ieee80211_tx_prep_agg. These frames
have IEEE80211_TX_CTL_NO_PS_BUFFER set since they are sent to
a sleeping client and possibly IEEE80211_TX_STATUS_EOSP.
If the frame is buffered, we need clear these two flags
since they will be re-sent after the move to
HT_AGG_STATE_OPERATIONAL state which is very likely to
happen after the SP ends.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fall back to rate control if the requested bitrate was not found.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MCS bandwidth part of the radiotap header is 2 bits wide. The full 2
bit have to compared against IEEE80211_RADIOTAP_MCS_BW_40 and not only if
the first bit is set. Otherwise IEEE80211_RADIOTAP_MCS_BW_40 can be
confused with IEEE80211_RADIOTAP_MCS_BW_20U.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Buffered multicast frames must be passed to the driver directly via
drv_tx instead of going through the txq, otherwise they cannot easily be
scheduled to be sent after DTIM.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT radiotap parsing support to ieee80211_parse_tx_radiotap().
That capability has been tested using a d-link dir-860l rev b1 running
OpenWrt trunk and mt76 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix wiphy supported_band access in tx radiotap parsing introduced
in commit 5ec3aed9ba4c ("mac80211: Parse legacy and HT rate in
injected frames"). In particular, info->band is always set to 0
(IEEE80211_BAND_2GHZ) since it has not assigned yet.
This cause a kernel crash on 5GHz only devices.
Move ieee80211_parse_tx_radiotap() after info->band assignment
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remember the last time when a mpp table entry is used for
rx or tx and remove them after MESH_PATH_EXPIRE time.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow drivers to make more educated
decisions whether to defer transmission or not.
Relying on wake_tx_queue() call count implicitly
was not possible because it could be called
without queued frame count actually changing on
software tx aggregation start/stop code paths.
It was also not possible to know how long
byte-wise queue was without dequeueing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers/devices without their own rate control algorithm can get the
information what rates they should use from either the radiotap header of
injected frames or from the rate control algorithm. But the parsing of the
legacy rate information from the radiotap header was removed in commit
e6a9854b05 ("mac80211/drivers: rewrite the rate control API").
The removal of this feature heavily reduced the usefulness of frame
injection when wanting to simulate specific transmission behavior. Having
rate parsing together with MCS rates and retry support allows a fine
grained selection of the tx behavior of injected frames for these kind of
tests.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=uZ5N
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another set of patches for the current cycle:
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Group station statistics by where they're (mostly) updated
(TX, RX and TX-status) and group them into sub-structs of
the struct sta_info.
Also rename the variables since the grouping now makes it
obvious where they belong.
This makes it easier to identify where the statistics are
updated in the code, and thus easier to think about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When using software queueing, tx sequence number assignment happens at
ieee80211_tx_dequeue time, so the fast-xmit codepath must not do that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When debugging wireless powersave issues on the AP side it's quite helpful
to see our own beacons that are transmitted by the hardware/driver. However,
this is not that easy since beacons don't pass through the regular TX queues.
Preferably drivers would call ieee80211_tx_status also for tx'ed beacons
but that's not always possible. Hence, just send a copy of each beacon
generated by ieee80211_beacon_get_tim to monitor devices when they are
getting fetched by the driver.
Also add a HW flag IEEE80211_HW_BEACON_TX_STATUS that can be used by
drivers to indicate that they report TX status for beacons.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
(with a fix from Christian Lamparted rolled in)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes dropped packets in the tx path in case a non-PS station triggers
the tx filter.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make mac80211 accept the multicast rate requested by the user the
rate control should be told that it is operating in BSS mode.
Without this, the default rate is selected in rate_control_send_low
(!pubsta and !txrc->bss)
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>