[ Upstream commit eb4733d7cffc547e08fe5a216e4f03663bb71108 ]
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The current assumption is that the felix DSA driver has flooding knobs
per traffic class, while ocelot switchdev has a single flooding knob.
This was correct for felix VSC9959 and ocelot VSC7514, but with the
introduction of seville VSC9953, we see a switch driven by felix.c which
has a single flooding knob.
So it is clear that we must do what should have been done from the
beginning, which is not to overwrite the configuration done by ocelot.c
in felix, but instead to teach the common ocelot library about the
differences in our switches, and set up the flooding PGIDs centrally.
The effect that the bogus iteration through FELIX_NUM_TC has upon
seville is quite dramatic. ANA_FLOODING is located at 0x00b548, and
ANA_FLOODING_IPMC is located at 0x00b54c. So the bogus iteration will
actually overwrite ANA_FLOODING_IPMC when attempting to write
ANA_FLOODING[1]. There is no ANA_FLOODING[1] in sevile, just ANA_FLOODING.
And when ANA_FLOODING_IPMC is overwritten with a bogus value, the effect
is that ANA_FLOODING_IPMC gets the value of 0x0003CF7D:
MC6_DATA = 61,
MC6_CTRL = 61,
MC4_DATA = 60,
MC4_CTRL = 0.
Because MC4_CTRL is zero, this means that IPv4 multicast control packets
are not flooded, but dropped. An invalid configuration, and this is how
the issue was actually spotted.
Reported-by: Eldar Gasanov <eldargasanov2@gmail.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Tested-by: Eldar Gasanov <eldargasanov2@gmail.com>
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 3c7b51bd39 ("net: dsa: felix: allow flooding for all traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201204175416.1445937-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Ocelot switches, there are 2 ingress pipelines for flow offload
rules: VCAP IS1 (Ingress Classification) and IS2 (Security Enforcement).
IS1 and IS2 support different sets of actions. The pipeline order for a
packet on ingress is:
Basic classification -> VCAP IS1 -> VCAP IS2
Furthermore, IS1 is looked up 3 times, and IS2 is looked up twice (each
TCAM entry can be configured to match only on the first lookup, or only
on the second, or on both etc).
Because the TCAMs are completely independent in hardware, and because of
the fixed pipeline, we actually have very limited options when it comes
to offloading complex rules to them while still maintaining the same
semantics with the software data path.
This patch maps flow offload rules to ingress TCAMs according to a
predefined chain index number. There is going to be a script in
selftests that clarifies the usage model.
There is also an egress TCAM (VCAP ES0, the Egress Rewriter), which is
modeled on top of the default chain 0 of the egress qdisc, because it
doesn't have multiple lookups.
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Co-developed-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some targets (register blocks) in the Ocelot switch that are
instantiated more than once. For example, the VCAP IS1, IS2 and ES0
blocks all share the same register layout for interacting with the cache
for the TCAM and the action RAM.
For the VCAPs, the procedure for servicing them is actually common. We
just need an API specifying which VCAP we are talking to, and we do that
via these raw ocelot_target_read and ocelot_target_write accessors.
In plain ocelot_read, the target is encoded into the register enum
itself:
u16 target = reg >> TARGET_OFFSET;
For the VCAPs, the registers are currently defined like this:
enum ocelot_reg {
[...]
S2_CORE_UPDATE_CTRL = S2 << TARGET_OFFSET,
S2_CORE_MV_CFG,
S2_CACHE_ENTRY_DAT,
S2_CACHE_MASK_DAT,
S2_CACHE_ACTION_DAT,
S2_CACHE_CNT_DAT,
S2_CACHE_TG_DAT,
[...]
};
which is precisely what we want to avoid, because we'd have to duplicate
the same register map for S1 and for S0, and then figure out how to pass
VCAP instance-specific registers to the ocelot_read calls (basically
another lookup table that undoes the effect of shifting with
TARGET_OFFSET).
So for some targets, propose a more raw API, similar to what is
currently done with ocelot_port_readl and ocelot_port_writel. Those
targets can only be accessed with ocelot_target_{read,write} and not
with ocelot_{read,write} after the conversion, which is fine.
The VCAP registers are not actually modified to use this new API as of
this patch. They will be modified in the next one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ocelot_configure_cpu() function, which was in fact bringing
up 2 ports: the CPU port module, which both switchdev and DSA have, and
the NPI port, which only DSA has.
The (non-Ethernet) CPU port module is at a fixed index in the analyzer,
whereas the NPI port is selected through the "ethernet" property in the
device tree.
Therefore, the function to set up an NPI port is DSA-specific, so we
move it there, simplifying the ocelot switch library a little bit.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.
This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a good measure to ensure correctness if the structures that are
meant to remain constant are only processed by functions that thake
constant arguments.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mscc_ocelot_init_ports() will skip initializing a port when it
doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
NULL. Take this into consideration when tearing down the driver, and add
a new function ocelot_deinit_port() to the switch library, mirror of
ocelot_init_port(), which needs to be called by the driver for all ports
it has initialized.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb8299 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current iterators are impossible to understand at first glance
without switching back and forth between the definitions and their
actual use in the for loops.
So introduce some convenience names to help readability.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the mdb hooks in felix and exports the mdb functions from
ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access Control Lists (and their respective Access Control Entries) are
specifically entries in the VCAP IS2, the security enforcement block,
according to the documentation.
Let's rename the structures and functions to something more generic, so
that VCAP IS1 structures (which would otherwise have to be called
Ingress Classification Entries) can reuse the same code without
confusion.
Some renaming that was done:
struct ocelot_ace_rule -> struct ocelot_vcap_filter
struct ocelot_acl_block -> struct ocelot_vcap_block
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_vlan -> struct ocelot_vcap_key_vlan
enum ocelot_ace_action -> enum ocelot_vcap_action
struct ocelot_ace_stats -> struct ocelot_vcap_stats
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_frame_* -> struct ocelot_vcap_key_*
No functional change is intended.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.
Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support 4 PTP programmable pins with only PTP_PF_PEROUT function
for now. The PTP_PF_EXTTS function will be supported in the
future, and it should be implemented separately for Felix and
Ocelot, because of different hardware interrupt implementation
in them.
Since the hardware is not able to support absolute start time,
the periodic clock request only allows start time 0 0. But nsec
could be accepted for PPS case for phase adjustment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 5 PTP_PINS register groups on Ocelot switch.
Except the one used for TOD operations, there are still
4 register groups for programmable pins. So redefine the
4 programmable pins.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To rehash a previous explanation given in commit 1c44ce560b ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e3 ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a trivial passthrough towards the ocelot library, which
support port policers since commit 2c1d029a01 ("net: mscc: ocelot:
Implement port policers via tc command").
Some data structure conversion between the DSA core and the Ocelot
library is necessary, for policer parameters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has 384 policers that can be allocated to ingress ports,
QoS classes per port, and VCAP IS2 entries. ocelot_police.c
supports to set policers which can be allocated to police action
of VCAP IS2. We allocate policers from maximum pol_id, and
decrease the pol_id when add a new vcap_is2 entry which is
police action.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What the driver writes into MAC_MAXLEN_CFG does not actually represent
VLAN_ETH_FRAME_LEN but instead ETH_FRAME_LEN + ETH_FCS_LEN. Yes they are
numerically equal, but the difference is important, as the switch treats
VLAN-tagged traffic specially and knows to increase the maximum accepted
frame size automatically. So it is always wrong to account for VLAN in
the MAC_MAXLEN_CFG register.
Unconditionally increase the maximum allowed frame size for
double-tagged traffic. Accounting for the additional length does not
mean that the other VLAN membership checks aren't performed, so there's
no harm done.
Also, stop abusing the MTU name for configuring the MRU. There is no
support for configuring the MRU on an interface at the moment.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Fixes: fa914e9c4d ("net: mscc: ocelot: create a helper for changing the port MTU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to other DSA switches, in the Ocelot cores, the RX filtering is
a much more important concern.
Firstly, the primary use case for Ocelot is non-DSA, so there isn't any
secondary Ethernet MAC [the DSA master's one] to implicitly drop frames
having a DMAC we are not interested in. So the switch driver itself
needs to install FDB entries towards the CPU port module (PGID_CPU) for
the MAC address of each switch port, in each VLAN installed on the port.
Every address that is not whitelisted is implicitly dropped. This is in
order to achieve a behavior similar to N standalone net devices.
Secondly, even in the secondary use case of DSA, such as illustrated by
Felix with the NPI port mode, that secondary Ethernet MAC is present,
but its RX filter is bypassed. This is because the DSA tags themselves
are placed before Ethernet, so the DMAC that the switch ports see is
not seen by the DSA master too (since it's shifter to the right).
So RX filtering is pretty important. A good RX filter won't bother the
CPU in case the switch port receives a frame that it's not interested
in, and there exists no other line of defense.
Ocelot is pretty strict when it comes to RX filtering: non-IP multicast
and broadcast traffic is allowed to go to the CPU port module, but
unknown unicast isn't. This means that traffic reception for any other
MAC addresses than the ones configured on each switch port net device
won't work. This includes use cases such as macvlan or bridging with a
non-Ocelot (so-called "foreign") interface. But this seems to be fine
for the scenarios that the Linux system embedded inside an Ocelot switch
is intended for - it is simply not interested in unknown unicast
traffic, as explained in Allan Nielsen's presentation [0].
On the other hand, the Felix DSA switch is integrated in more
general-purpose Linux systems, so it can't afford to drop that sort of
traffic in hardware, even if it will end up doing so later, in software.
Actually, unknown unicast means more for Felix than it does for Ocelot.
Felix doesn't attempt to perform the whitelisting of switch port MAC
addresses towards PGID_CPU at all, mainly because it is too complicated
to be feasible: while the MAC addresses are unique in Ocelot, by default
in DSA all ports are equal and inherited from the DSA master. This adds
into account the question of reference counting MAC addresses (delayed
ocelot_mact_forget), not to mention reference counting for the VLAN IDs
that those MAC addresses are installed in. This reference counting
should be done in the DSA core, and the fact that it wasn't needed so
far is due to the fact that the other DSA switches don't have the DSA
tag placed before Ethernet, so the DSA master is able to whitelist the
MAC addresses in hardware.
So this means that even regular traffic termination on a Felix switch
port happens through flooding (because neither Felix nor Ocelot learn
source MAC addresses from CPU-injected frames).
So far we've explained that whitelisting towards PGID_CPU:
- helps to reduce the likelihood of spamming the CPU with frames it
won't process very far anyway
- is implemented in the ocelot driver
- is sufficient for the ocelot use cases
- is not feasible in DSA
- breaks use cases in DSA, in the current status (whitelisting enabled
but no MAC address whitelisted)
So the proposed patch allows unknown unicast frames to be sent to the
CPU port module. This is done for the Felix DSA driver only, as Ocelot
seems to be happy without it.
[0]: https://www.youtube.com/watch?v=B1HhxEcU7Jg
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.
Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the definitions for the VCAP IS2 table from ocelot_ace.c, since
it is specific to VSC7514.
The VSC9959 VCAP IS2 table supports more rules (1024 instead of 64) and
has a different width for the action (89 bits instead of 99).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver is now using its own PHYLINK instance, not calling into
ocelot_adjust_link. So the port_pcs_init function pointer is an
unnecessary indirection. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGR_PORT_MASK key width is different between the 11-port VSC7514 and
the 6-port VSC9959 switches. And since IGR_PORT_MASK is one of the first
fields of a VCAP key entry, it means that all further field
offset/length pairs are shifted between the 2.
The ocelot driver performs packing of VCAP half keys with the help of
some preprocessor macros:
- A set of macros for defining the HKO (Half Key Offset) and HKL (Half
Key Length) of each possible key field. The offset of each field is
defined as the sum between the offset and the sum of the previous
field.
- A set of accessors on top of vcap_key_set for shorter (aka less
typing) access to the HKO and HKL of each key field.
Since the field offsets and lengths are different between switches,
defining them through the preprocessor isn't going to fly. So introduce
a structure holding (offset, length) pairs and instantiate it in
ocelot_board.c for VSC7514. In a future patch, a similar structure will
be instantiated in felix_vsc9959.c for NXP LS1028A.
The accessors also need to go. They are based on macro name
concatenation, which is horrible to understand and follow.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot tc-flower offload binds a second flow block callback (apart
from the one for matchall) just because it uses a different block
private structure (ocelot_port_private for matchall, ocelot_port_block
for flower).
But ocelot_port_block just appears to be boilerplate, and doesn't help
with anything in particular at all, it's just useless glue between the
(global!) struct ocelot_acl_block *block pointer, and a per-netdevice
struct ocelot_port_private *priv.
So let's just simplify that, and make struct ocelot_port_private be the
private structure for the block offload. This makes us able to use the
same flow callback as in the case of matchall.
This also reveals that the struct ocelot_acl_block *block is used rather
strangely, as mentioned above: it is defined globally, allocated at
probe time, and freed at unbind time. So just move the structure to the
main ocelot structure, which gives further opportunity for
simplification.
Also get rid of backpointers from struct ocelot_acl_block and struct
ocelot_ace_rule back to struct ocelot, by reworking the function
prototypes, where necessary, to use a more DSA-friendly "struct ocelot
*ocelot, int port" format.
And finally, remove the debugging prints that were added during
development, since they provide no useful information at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the Felix DSA driver is implementing its own PHYLINK instance due
to SoC differences, it needs access to the few registers that are
common, mainly for flow control.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot switchdev driver and the Felix DSA one need it for different
reasons. Felix (or at least the VSC9959 instantiation in NXP LS1028A) is
integrated with the traditional NXP Layerscape PCS design which does not
support runtime configuration of SerDes protocol. So it needs to
pre-validate the phy-mode from the device tree and prevent PHYLINK from
attempting to change it. For this, it needs to cache it in a private
variable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to use skb queue instead of the list of skbs.
The skb queue could provide protection with lock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
