commit c6d580d96f140596d69220f60ce0cfbea4ee5c0f upstream.
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org>
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7721e15f434920145c376e8fe77e1c079fc3726 upstream.
According to the i.MX6UL Errata document:
https://www.nxp.com/docs/en/errata/IMX6ULCE.pdf
ERR007881 also affects i.MX6UL, so pass the
CI_HDRC_DISABLE_DEVICE_STREAMING flag to workaround the issue.
Fixes: 52fe568e5d ("usb: chipidea: imx: add imx6ul usb support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201207020909.22483-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinctrl setting may lost during the system suspend
(eg, imx7ulp), it needs to restore them after system resume.
Meanwhile, some platforms may need to set special pinctrl
for power comsumption.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
These two parameters are used to improve USB signal for board level,
in this commit, we read it from the dtb, and write to related register
during the initialization.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl8g2ksACgkQSFkpgVDW
cbtAMwf/dkrCfmE2HpvAsZqL68WOC1yTaN9f3v7bzXc2oD2WRsk3aKGZGLeXvMtN
aruD3ctxOVEom5FHrff8x3G1CBw8wsbl+yjT6aTlbcFY/Yzmww7RABUO5Xp1F9aB
aTuDcLeoY22UHkzNdeNrixEuOR9xeyhZjFybW0cZ6FddP0mj4SUNNczxfaGvmLLI
DOJ7oc8KC9pIwhoF9065GH0p5PrXVnZvcBUXWs5PASjj4lWb3DiMGxhZRPBLbB6l
YifzRa+C90BP4AjTptS03fD/3knciZCM8Z1GsVYdKLuO4NOPlcZeEJEeUGmkCr0L
QmOpk5Sh8nACisOCqn3gQDo7jAI6Mg==
=JnWY
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
ENDIAN issue fix and one query controller role API is introduced.
* tag 'usb-ci-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: get available runtime dr mode for wakeup setting
usb: chipidea: add query_available_role interface
Documentation: ABI: usb: chipidea: Update Li Jun's e-mail
usb: chipidea: udc: fix the ENDIAN issue
If runtime dr_mode is not dual-role, it doesn't need to enable ID
wakeup interrupt.
If runtime dr_mode is host, it doesn't need to enable VBUS
wakeup interrupt.
With these changes, the user will not get the unexpected wakeup
for single role use case. For example, the host-only use case at
Micro-AB port, the controller should not be waken up by only
plug in Micro-AB cable or the Micro-B cable with host.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The glue layer may need to know current available role to do some
setting, eg, the wakeup setting. So we add ci_hdrc_query_available_role
for that.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No attempt has been made to document any of the structure's properties here.
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/ci_hdrc_pci.c:132: warning: cannot understand function prototype: 'const struct pci_device_id ci_hdrc_pci_id_table[] = '
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: David Lopo <dlopo@chipidea.mips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200706133341.476881-3-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No attempt has been made to document the demoted function here.
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/usbmisc_imx.c:801: warning: Function parameter or member 'data' not described in 'imx7d_charger_detection'
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-24-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Descriptions were missing for 'ci' almost throughout. There was
one instance of over-documenting. Finally one function argument
was incorrectly documented (probably down to bitrot).
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/udc.c:245: warning: Function parameter or member 'ci' not described in 'hw_port_is_high_speed'
drivers/usb/chipidea/udc.c:271: warning: Function parameter or member 'ci' not described in 'hw_test_and_clear_intr_active'
drivers/usb/chipidea/udc.c:285: warning: Function parameter or member 'ci' not described in 'hw_test_and_clear_setup_guard'
drivers/usb/chipidea/udc.c:296: warning: Function parameter or member 'ci' not described in 'hw_test_and_set_setup_guard'
drivers/usb/chipidea/udc.c:321: warning: Function parameter or member 'ci' not described in 'hw_usb_reset'
drivers/usb/chipidea/udc.c:628: warning: Excess function parameter 'ci' description in 'free_pending_td'
drivers/usb/chipidea/udc.c:655: warning: Function parameter or member 'hwep' not described in '_hardware_dequeue'
drivers/usb/chipidea/udc.c:655: warning: Excess function parameter 'gadget' description in '_hardware_dequeue'
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-18-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Help with adding the odd description where they have been omitted or
where the format isn't quite right. Demote all function headers which
are lacking any attempt of describing their arguments.
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/udc.c:645: warning: Function parameter or member 'hwreq' not described in '_hardware_dequeue'
drivers/usb/chipidea/udc.c:645: warning: Excess function parameter 'gadget' description in '_hardware_dequeue'
drivers/usb/chipidea/udc.c:1326: warning: Function parameter or member 'ep' not described in 'ep_enable'
drivers/usb/chipidea/udc.c:1326: warning: Function parameter or member 'desc' not described in 'ep_enable'
drivers/usb/chipidea/udc.c:1393: warning: Function parameter or member 'ep' not described in 'ep_disable'
drivers/usb/chipidea/udc.c:1433: warning: Function parameter or member 'ep' not described in 'ep_alloc_request'
drivers/usb/chipidea/udc.c:1433: warning: Function parameter or member 'gfp_flags' not described in 'ep_alloc_request'
drivers/usb/chipidea/udc.c:1454: warning: Function parameter or member 'ep' not described in 'ep_free_request'
drivers/usb/chipidea/udc.c:1454: warning: Function parameter or member 'req' not described in 'ep_free_request'
drivers/usb/chipidea/udc.c:1488: warning: Function parameter or member 'ep' not described in 'ep_queue'
drivers/usb/chipidea/udc.c:1488: warning: Function parameter or member 'req' not described in 'ep_queue'
drivers/usb/chipidea/udc.c:1488: warning: Function parameter or member 'gfp_flags' not described in 'ep_queue'
drivers/usb/chipidea/udc.c:1512: warning: Function parameter or member 'ep' not described in 'ep_dequeue'
drivers/usb/chipidea/udc.c:1512: warning: Function parameter or member 'req' not described in 'ep_dequeue'
drivers/usb/chipidea/udc.c:1556: warning: Function parameter or member 'ep' not described in 'ep_set_halt'
drivers/usb/chipidea/udc.c:1556: warning: Function parameter or member 'value' not described in 'ep_set_halt'
drivers/usb/chipidea/udc.c:1566: warning: Function parameter or member 'ep' not described in 'ep_set_wedge'
drivers/usb/chipidea/udc.c:1586: warning: Function parameter or member 'ep' not described in 'ep_fifo_flush'
drivers/usb/chipidea/udc.c:1610: warning: cannot understand function prototype: 'const struct usb_ep_ops usb_ep_ops = '
drivers/usb/chipidea/udc.c:1629: warning: Function parameter or member '_gadget' not described in 'ci_hdrc_gadget_connect'
drivers/usb/chipidea/udc.c:1629: warning: Function parameter or member 'is_active' not described in 'ci_hdrc_gadget_connect'
drivers/usb/chipidea/udc.c:1780: warning: cannot understand function prototype: 'const struct usb_gadget_ops usb_gadget_ops = '
drivers/usb/chipidea/udc.c:1931: warning: Function parameter or member 'gadget' not described in 'ci_udc_stop'
drivers/usb/chipidea/udc.c:1965: warning: Function parameter or member 'ci' not described in 'udc_irq'
drivers/usb/chipidea/udc.c:2095: warning: Function parameter or member 'ci' not described in 'ci_hdrc_gadget_destroy'
drivers/usb/chipidea/udc.c:2144: warning: Function parameter or member 'ci' not described in 'ci_hdrc_gadget_init'
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-13-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like a very popular argument to omit descriptions for.
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/udc.c:80: warning: Function parameter or member 'ci' not described in 'hw_device_state'
drivers/usb/chipidea/udc.c💯 warning: Function parameter or member 'ci' not described in 'hw_ep_flush'
drivers/usb/chipidea/udc.c:121: warning: Function parameter or member 'ci' not described in 'hw_ep_disable'
drivers/usb/chipidea/udc.c:136: warning: Function parameter or member 'ci' not described in 'hw_ep_enable'
drivers/usb/chipidea/udc.c:170: warning: Function parameter or member 'ci' not described in 'hw_ep_get_halt'
drivers/usb/chipidea/udc.c:185: warning: Function parameter or member 'ci' not described in 'hw_ep_prime'
drivers/usb/chipidea/udc.c:215: warning: Function parameter or member 'ci' not described in 'hw_ep_set_halt'
drivers/usb/chipidea/udc.c:238: warning: Function parameter or member 'ci' not described in 'hw_port_is_high_speed'
drivers/usb/chipidea/udc.c:251: warning: Function parameter or member 'ci' not described in 'hw_test_and_clear_complete'
drivers/usb/chipidea/udc.c:263: warning: Function parameter or member 'ci' not described in 'hw_test_and_clear_intr_active'
drivers/usb/chipidea/udc.c:277: warning: Function parameter or member 'ci' not described in 'hw_test_and_clear_setup_guard'
drivers/usb/chipidea/udc.c:288: warning: Function parameter or member 'ci' not described in 'hw_test_and_set_setup_guard'
drivers/usb/chipidea/udc.c:300: warning: Function parameter or member 'ci' not described in 'hw_usb_set_address'
drivers/usb/chipidea/udc.c:312: warning: Function parameter or member 'ci' not described in 'hw_usb_reset'
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-12-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No attempt has been made to document any of the demoted functions here.
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/debug.c:25: warning: Function parameter or member 's' not described in 'ci_device_show'
drivers/usb/chipidea/debug.c:25: warning: Function parameter or member 'data' not described in 'ci_device_show'
drivers/usb/chipidea/debug.c:54: warning: Function parameter or member 's' not described in 'ci_port_test_show'
drivers/usb/chipidea/debug.c:54: warning: Function parameter or member 'data' not described in 'ci_port_test_show'
drivers/usb/chipidea/debug.c:75: warning: Function parameter or member 'file' not described in 'ci_port_test_write'
drivers/usb/chipidea/debug.c:75: warning: Function parameter or member 'ubuf' not described in 'ci_port_test_write'
drivers/usb/chipidea/debug.c:75: warning: Function parameter or member 'count' not described in 'ci_port_test_write'
drivers/usb/chipidea/debug.c:75: warning: Function parameter or member 'ppos' not described in 'ci_port_test_write'
drivers/usb/chipidea/debug.c:122: warning: Function parameter or member 's' not described in 'ci_qheads_show'
drivers/usb/chipidea/debug.c:122: warning: Function parameter or member 'data' not described in 'ci_qheads_show'
drivers/usb/chipidea/debug.c:154: warning: Function parameter or member 's' not described in 'ci_requests_show'
drivers/usb/chipidea/debug.c:154: warning: Function parameter or member 'data' not described in 'ci_requests_show'
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-11-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly we add some missing descriptions. Then we fix some formatting
issues. Kerneldoc expects arguments to be in the format '@.*: '. If
either the '@' or ':' is omitted, kerneldoc gets confused.
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/otg.c:29: warning: Function parameter or member 'ci' not described in 'hw_read_otgsc'
drivers/usb/chipidea/otg.c:82: warning: Function parameter or member 'ci' not described in 'hw_write_otgsc'
drivers/usb/chipidea/otg.c:235: warning: Function parameter or member 'ci' not described in 'ci_hdrc_otg_init'
drivers/usb/chipidea/otg.c:254: warning: Function parameter or member 'ci' not described in 'ci_hdrc_otg_destroy'
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-10-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/chipidea/core.c:163: warning: Function parameter or member 'ci' not described in 'hw_port_test_set'
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: David Lopo <dlopo@chipidea.mips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-8-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If wakeup event occurred by extcon event, it needs to call
ci_irq again since the first ci_irq calling at extcon notifier
only wakes up controller, but do noop for event handling,
it causes the extcon use case can't work well from low power mode.
Cc: <stable@vger.kernel.org>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Reported-by: Philippe Schenker <philippe.schenker@toradex.com>
Tested-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200707060601.31907-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the TEST_ defines in the usb/ch9.h files did not have
the USB_ prefix on it, making it a bit confusing when reading the file,
as well as not the nicest thing to do in a uapi file.
So fix that up and add the USB_ prefix on to them, and fix up all
in-kernel usages. This included deleting the duplicate copy in the
net2272.h file.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jules Irenge <jbi.octave@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: Rob Gill <rrobgill@protonmail.com>
Cc: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Bin Liu <b-liu@ti.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200618144206.2655890-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Support imx7d USB charger
- Add software sg support for UDC
- Enable user trigger role switch
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl7Mf1oACgkQSFkpgVDW
cbskgggAvRbKPI2Zbw4tHa1JgwkADxg2Q3ewxFLiNIJ7GVLpZeiBn4Dziong6za9
1tB/f4qVyAlVT/zLYrxo9oCMwmGOLJjxigGLqJ2iMtDqcRG++jCdirTMXiI2Fdlh
ZCup49W0IWKmQ7mSLK0TDVbEpYT8YOICiCJumMxhMYuP6bfgFihPjh8NTiz4X7Jr
SUw5rCS7qTRAwDeywIbzWIeCmc4MKaohx4t/XD4Xxz0rPvJrkPgZAaiPh9vJzyMh
2XgFZovLin46QaVbSxxhTUJ7PitCQYzXF+W5vqsdtHkj2u3N3o0MPbSDCKT3oYUb
2zLS7SHzHuKmgFSnxOcLI56gF32uHg==
=YwB9
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Some improvments for ci_hdrc_usb2.c
- Support imx7d USB charger
- Add software sg support for UDC
- Enable user trigger role switch
* tag 'usb-ci-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: Enable user-space triggered role-switching
usb: chipidea: udc: add software sg list support
usb: chipidea: usbmisc_imx: using different ops for imx7d and imx7ulp
usb: chipidea: pull down dp for possible charger detection operation
usb: chipidea: introduce imx7d USB charger detection
usb: chipidea: introduce CI_HDRC_CONTROLLER_VBUS_EVENT glue layer use
usb: chipidea: usb2: remove unneeded semicolon
usb: chipidea: allow disabling glue drivers if EMBEDDED
usb: chipidea: usb2: absorb zevio glue driver
usb: chipidea: usb2: make clock optional
usb: chipidea: usb2: fix formatting
usb: chipidea: usb2: constify zynq_pdata
usb: chipidea: core: show the real pointer value for register
usb: chipidea: core: refine the description for this driver
usb: chipidea: udc: fix the kernel doc for udc.h
Currently we check to make sure there is no error state on the extcon
handle for VBUS when writing to the HS_PHY_GENCONFIG_2 register. When using
the USB role-switch API we still need to write to this register absent an
extcon handle.
This patch makes the appropriate update to ensure the write happens if
role-switching is true.
Fixes: 05559f10ed ("usb: chipidea: add role switch class support")
Cc: stable <stable@vger.kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200507004918.25975-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flag provided by the USB role-switch logic allow_userspace_control
allows user-space to trigger a role-switch. Several other USB controller
drivers already enable this feature. Let's switch it on for the chipidea
core now also.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Jun Li <jun.li@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx7ulp uses different USB PHY with imx7d (MXS PHY vs PICO PHY), so the
features are supported by non-core register are a little different.
For example, autoresume feature is supported by all controllers for
imx7ulp, but for imx7d, it is only supported by non-HSIC controller.
Besides, these two platforms use different HSIC controller, imx7ulp
needs software operation, but imx7d doesn't.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The bootloader may use device mode, and keep dp up. We need dp
to be pulled down before possbile charger detection operation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx7d (and imx8mm, imx8mn) uses Samsung PHY and USB generic PHY driver.
The USB generic PHY driver is impossible to have a charger detection
for every user, so we implement USB charger detection routine at glue
layer. After the detection has finished, it will notify USB PHY
charger framework, and the uevents will be triggered.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some vendors glue layer need to handle some events for vbus, eg,
some i.mx platforms (imx7d, imx8mm, imx8mn, etc) needs vbus event
to handle charger detection, its charger detection is finished at
glue layer code, but not at USB PHY driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fix the following coccicheck warning:
drivers/usb/chipidea/ci_hdrc_usb2.c:75:28-29: Unneeded semicolon
Fixes: c2de37b31f ("usb: chipidea: usb2: make clock optional")
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Allow to cut down on driver size for embedded config.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
ZEVIO glue code is is identical to generic binding now, but doesn't
enable runtime PM. Let's squash the driver and get runtime PM for free.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Allow clock to be missing from DT (assume it's enabled then).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
pdata is copied anyway to allow setting device name.
Make the source const.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----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=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
The pointer value is "ptrval" like below at current code:
ci_hdrc ci_hdrc.0: ChipIdea HDRC found, revision: 25, lpm: 0;
cap: (ptrval) op: (ptrval)
According to Documentation/core-api/printk-formats.rst, we change
it from %p to %px for real value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
During system suspend, the role switch may occur, eg, from gadget->host.
In this case, the vbus disconnect event is lost, we add this handling
in role switch routine in this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
At current code, it doesn't maintain ci->gadget.dev's runtime PM
status well, eg, during the PM operation, the PM counter for
ci->gadget.dev doesn't be changed accordingly.
In this commit, we use ci_hdrc device instead of ci->gadget.dev
for runtime PM APIs at udc driver, in the way, we handle runtime
PM APIs using unify device structure between core and udc driver.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The USB role callback functions had a parameter pointing to
the parent device (struct device) of the switch. The
assumption was that the switch parent is always the
controller. Firstly, that may not be true in every case, and
secondly, it prevents us from supporting devices that supply
multiple muxes.
Changing the first parameter of usb_role_switch_set_t and
usb_role_switch_get_t from struct device to struct
usb_role_switch.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Otherwise, there is a build warning if this header file is included
by non host source file, eg, otg.c.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200122014639.22667-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb port is configed to be single role, but usb role class
is trying to set unavailable role, don't try to do role change.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200122014639.22667-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
