Ports should be defined in the devicetree if they are to be enabled on
the system.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang. The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver. It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.
When the system hangs, I found that it was running the geni_i2c_irq()
over and over again. It had these:
m_stat = 0x04000080
rx_st = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep(). If a transfer makes it
far enough before we do that then we get into the state I have
observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too. Change it as well.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1].
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
For RPMh this fixes an issue where ktime was used during suspend, allows
the driver to be used on ARM targets and some minor cleanups.
It adds support for the latest format version in the socinfo driver and
adds identifiers for SM8250 and SDM630.
SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM
gains compatibles MSM8994 and IPQ8074.
The GENI core code gains interconnect path voting and performance level
support, with subsequent patches integrating this with the SPI, I2C,
UART and QSPI drivers.
Following this the KGDB support for the GENI serial driver is improved,
the performance related to chip-select is improved for SPI and QSPI.
-----BEGIN PGP SIGNATURE-----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=Os4F
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.9
For RPMh this fixes an issue where ktime was used during suspend, allows
the driver to be used on ARM targets and some minor cleanups.
It adds support for the latest format version in the socinfo driver and
adds identifiers for SM8250 and SDM630.
SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM
gains compatibles MSM8994 and IPQ8074.
The GENI core code gains interconnect path voting and performance level
support, with subsequent patches integrating this with the SPI, I2C,
UART and QSPI drivers.
Following this the KGDB support for the GENI serial driver is improved,
the performance related to chip-select is improved for SPI and QSPI.
* tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (35 commits)
soc: qcom: geni: Fix NULL pointer dereference
tty: serial: qcom-geni-serial: Drop the icc bw votes in suspend for console
serial: qcom_geni_serial: Always use 4 bytes per TX FIFO word
serial: qcom_geni_serial: Make kgdb work even if UART isn't console
spi: spi-geni-qcom: Get rid of most overhead in prepare_message()
spi: spi-geni-qcom: Set the clock properly at runtime resume
spi: spi-geni-qcom: Avoid clock setting if not needed
spi: spi-qcom-qspi: Set an autosuspend delay of 250 ms
spi: spi-qcom-qspi: Avoid clock setting if not needed
spi: spi-qcom-qspi: Use OPP API to set clk/perf state
firmware: qcom_scm: Add msm8994 compatible
firmware: qcom_scm: Fix legacy convention SCM accessors
<linux/of.h>: add stub for of_get_next_parent() to fix qcom build error
dt-bindings: firmware: qcom: Add compatible for IPQ8074 SoC
spi: spi-geni-qcom: Use OPP API to set clk/perf state
tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state
spi: spi-qcom-qspi: Add interconnect support
spi: spi-geni-qcom: Add interconnect support
spi: spi-geni-qcom: Combine the clock setting code
tty: serial: qcom_geni_serial: Add interconnect support
...
Link: https://lore.kernel.org/r/20200721044812.3429652-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.
This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.
One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).
So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit d358def706.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Enable i2c transactions in irq disabled contexts like poweroff where the
PMIC is connected via i2c.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Modules with multiple authors should use multiple MODULE_AUTHOR()
statements according to comment in include/linux/module.h.
Split the i2c modules with multiple authors to use multiple
MODULE_AUTHOR() statements.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno
to what is suggested for this error.
Fixes: c9bfdc7c16 ("i2c: mlxcpld: Add support for smbus block read transaction")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michael Shych <michaelsh@mellanox.com>
Tested-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I can't recall why there was none, but we surely want to have it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add more details which have either been missing ever since or describe
recent additions.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Current AMD's zen-based APUs use this core for some of its i2c-buses.
With this patch we re-enable autodetection of hwmon-alike devices, so
lm-sensors will be able to work automatically.
It does not affect the boot-time of embedded devices, as the class is
set based on the DMI information.
DMI is probed only on Qtechnology QT5222 Industrial Camera Platform.
DocLink: https://qtec.com/camera-technology-camera-platforms/
Fixes: 3eddad96c4 ("i2c: designware: reverts "i2c: designware: Add support for AMD I2C controller"")
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.
Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.
Fixes: eff9ec95ef ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The unicore32 port is removed from the kernel.
There is no point to keep stale i2c bus driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
If the i2c bus driver ignores the I2C_M_RECV_LEN flag (as some of
them do), it is possible for an I2C_SMBUS_BLOCK_DATA read issued
on some random device to return an arbitrary value in the first
byte (and nothing else). When this happens, i2c_smbus_xfer_emulated()
will happily write past the end of the supplied data buffer, thus
causing Bad Things to happen. To prevent this, check the size
before copying the data block and return an error if it is too large.
Fixes: 209d27c3b1 ("i2c: Emulate SMBus block read over I2C")
Signed-off-by: Mans Rullgard <mans@mansr.com>
[wsa: use better errno]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The port number field in the status register was not correct, so fix it.
Fixes: d6ffb63001 ("i2c: Add FSI-attached I2C master algorithm")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Get the interconnect paths for I2C based Serial Engine device
and vote according to the bus speed of the driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/1592908737-7068-4-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
John Stultz reported that commit f9288fcc5c ("i2c: designware: Move
ACPI parts into common module") caused a regression on the HiKey board
where adv7511 HDMI bridge driver wasn't probing anymore due the I2C bus
failed to start.
It seems the change caused the bus speed being zero when CONFIG_ACPI
not set and neither speed based on "clock-frequency" device property
or default fast mode is set.
Fix this by splitting i2c_dw_acpi_adjust_bus_speed() to
i2c_dw_acpi_round_bus_speed() and i2c_dw_adjust_bus_speed(), where
the latter one has the code that runs independently of ACPI.
Fixes: f9288fcc5c ("i2c: designware: Move ACPI parts into common module")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix spelling mistake in the comments with help of `codespell`.
seperate ==> separate
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
All in-tree users have been converted to the new i2c_new_client_device
function, so remove this deprecated one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
-----BEGIN PGP SIGNATURE-----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=1NIT
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
Pull i2c updates from Wolfram Sang:
"I2C has quite some patches for you this time. I hope it is the move to
per-driver-maintainers which is now showing results. We will see.
The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
larger refactoring of the Designware, Tegra, and PXA drivers, the
Cadence driver supports being a slave now, and there is support to
instanciate SPD eeproms for well-known cases (which will be
user-visible because the i801 driver supports it), and some
devm_platform_ioremap_resource() conversions which blow up the
diffstat.
Note that I applied the Nuvoton driver quite late, so some minor fixup
patches arrived during the merge window. I chose to apply them right
away because they were trivial"
* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
i2c: Drop stray comma in MODULE_AUTHOR statements
i2c: npcm7xx: npcm_i2caddr[] can be static
MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
i2c: npcm7xx: Fix a couple of error codes in probe
i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
i2c: npcm7xx: Remove unnecessary parentheses
i2c: npcm7xx: Add support for slave mode for Nuvoton
i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
dt-bindings: i2c: npcm7xx: add NPCM I2C controller
i2c: pxa: don't error out if there's no pinctrl
i2c: add 'single-master' property to generic bindings
i2c: designware: Add Baikal-T1 System I2C support
i2c: designware: Move reg-space remapping into a dedicated function
i2c: designware: Retrieve quirk flags as early as possible
i2c: designware: Convert driver to using regmap API
i2c: designware: Discard Cherry Trail model flag
i2c: designware: Add Baytrail sem config DW I2C platform dependency
i2c: designware: slave: Set DW I2C core module dependency
i2c: designware: Use `-y` to build multi-object modules
dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
It is not the common usage to have a comma between the name and the
email address, so remove it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fixes: f54736925a ("i2c: npcm7xx: Add support for slave mode for Nuvoton")
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
The code here is accidentally returning IS_ERR() which is 1 but it
should be returning negative error codes with PTR_ERR().
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This has been found by the Kernel Test Robot:
http://lkml.iu.edu/hypermail/linux/kernel/2006.0/06862.html
With CONFIG_AMIGA_PCMCIA=n, io_mm.h does not pull in amigahw.h and
ZTWO_VADDR is undefined. Add forgotten include to i2c-icy.c
Fixes: 4768e90eca ("i2c: Add i2c-icy for I2C on m68k/Amiga")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove unnecessary parentheses around _bus_.
This issue was found with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Core changes:
- A new GPIO aggregator driver has been merged: this can
join a few select GPIO lines into a new aggregated GPIO
chip. This can be used for security: a process can be
granted access to only these lines, for example for
industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or
container.
- Warn if the gpio-line-names is too long in he DT parser
core.
- GPIO lines can now be looked up by line name in addition
to being looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too
many regmap drivers are starting to look like each other
so we need to create some common ground and try to move
drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines
and several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey
Semin has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger
effort to make the ARM platforms more modular.
-----BEGIN PGP SIGNATURE-----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=B5OK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.8 kernel cycle.
Core changes:
- A new GPIO aggregator driver has been merged: this can join a few
select GPIO lines into a new aggregated GPIO chip. This can be used
for security: a process can be granted access to only these lines,
for example for industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or container.
- Warn if the gpio-line-names is too long in he DT parser core.
- GPIO lines can now be looked up by line name in addition to being
looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too many regmap
drivers are starting to look like each other so we need to create
some common ground and try to move drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines and
several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey Semin
has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger effort
to make the ARM platforms more modular"
* tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: pca953x: Drop unneeded ACPI_PTR()
MAINTAINERS: Add gpio regmap section
gpio: add a reusable generic gpio_chip using regmap
gpiolib: Introduce gpiochip_irqchip_add_domain()
gpio: gpiolib: Allow GPIO IRQs to lazy disable
gpiolib: Separate GPIO_GET_LINEINFO_WATCH_IOCTL conditional
gpio: rcar: Fix runtime PM imbalance on error
gpio: pca935x: Allow IRQ support for driver built as a module
gpio: pxa: Add COMPILE_TEST support
dt-bindings: gpio: Add renesas,em-gio bindings
MAINTAINERS: Fix file name for DesignWare GPIO DT schema
gpio: dwapb: Remove unneeded has_irq member in struct dwapb_port_property
gpio: dwapb: Don't use IRQ 0 as valid Linux interrupt
gpio: dwapb: avoid error message for optional IRQ
gpio: dwapb: Call acpi_gpiochip_free_interrupts() on GPIO chip de-registration
gpio: max730x: bring gpiochip_add_data after port config
MAINTAINERS: Add GPIO Aggregator section
docs: gpio: Add GPIO Aggregator documentation
gpio: Add GPIO Aggregator
gpiolib: Add support for GPIO lookup by line name
...
Add support for slave mode for Nuvoton
NPCM BMC I2C controller driver.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add Nuvoton NPCM BMC I2C controller driver.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The bus recovery patch regresses on OLPC XO-1.75 that has no pinctrl in
its DT.
Fixes: 7c9ec2c525 ("i2c: pxa: implement generic i2c bus recovery")'
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Baikal-T1 System Controller is equipped with a dedicated I2C Controller
which functionality is based on the DW APB I2C IP-core, the only
difference in a way it' registers are accessed. There are three access
register provided in the System Controller registers map, which indirectly
address the normal DW APB I2C registers space. So in order to have the
Baikal-T1 System I2C Controller supported by the common DW APB I2C driver
we created a dedicated Dw I2C controller model quirk, which retrieves the
syscon regmap from the parental dt node and creates a new regmap based on
it.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This is a preparation patch before adding a quirk with custom registers
map creation required for the Baikal-T1 System I2C support.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some platforms might need to activate the driver quirks at a very early
probe stage. For instance, Baikal-T1 System I2C doesn't need to map the
registers space as ones belong to the system controller. Instead it will
request the syscon regmap from the parental DT node. In order to be able
to do so let's retrieve the model flags right after the DW I2C private
data is created. While at it replace the or-assignment with just
assignment operator since or-ing is redundant at this stage.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Seeing the DW I2C driver is using flags-based accessors with two
conditional clauses it would be better to replace them with the regmap
API IO methods and to initialize the regmap object with read/write
callbacks specific to the controller registers map implementation. This
will be also handy for the drivers with non-standard registers mapping
(like an embedded into the Baikal-T1 System Controller DW I2C block, which
glue-driver is a part of this series).
As before the driver tries to detect the mapping setup at probe stage and
creates a regmap object accordingly, which will be used by the rest of the
code to correctly access the controller registers. In two places it was
appropriate to convert the hand-written read-modify-write and
read-poll-loop design patterns to the corresponding regmap API
ready-to-use methods.
Note the regmap IO methods return value is checked only at the probe
stage. The rest of the code won't do this because basically we have
MMIO-based regmap so non of the read/write methods can fail (this also
won't be needed for the Baikal-T1-specific I2C controller).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: fix type of 'rx_valid' and remove outdated kdoc var description]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A PM workaround activated by the flag MODEL_CHERRYTRAIL has been removed
since commit 9cbeeca050 ("i2c: designware: Remove Cherry Trail PMIC I2C
bus pm_disabled workaround"), but the flag most likely by mistake has been
left in the Dw I2C drivers. Let's remove it. Since MODEL_MSCC_OCELOT is
the only model-flag left, redefine it to be 0x100 so setting a very first
bit in the MODEL_MASK bits range.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently Intel Baytrail I2C semaphore is a feature of the DW APB I2C
platform driver. It's a bit confusing to see it's config in the menu at
some separated place with no reference to the platform code. Let's move the
config definition to be below the I2C_DESIGNWARE_PLATFORM config and mark
it with "depends on I2C_DESIGNWARE_PLATFORM" statement. By doing so the
config menu will display the feature right below the DW I2C platform
driver item and will indent it to the right so signifying its belonging.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DW APB I2C slave code in fact depends on the DW I2C driver core, but not
on the platform code as it used to be before commit 90bc1ee6de9f ("i2c:
designware: Allow slave mode for PCI enumerated devices"). Yes, the I2C
slave interface is currently supported by both the platform and PCI
versions of the IP core, but it still depends on the DW I2C core
functionality and must be available only if the last one is enabled.
So make sure the DW APB I2C slave config is only available if the
I2C_DESIGNWARE_CORE config is enabled.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since commit 4f82728027 ("Documentation: update kbuild loadable modules
goals & examples") `-objs` is fitted for building host programs, lets
change DW I2C core, platform and PCI driver kbuild directives to using
`-y`, which more straightforward for device drivers. By doing so we can
discard the ifeq construction in favor to the more natural and less bulky
`<module>-$(CONFIG_X) += x.o`
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This currently generates a warning:
drivers/i2c/busses/i2c-sh_mobile.c: In function 'sh_mobile_i2c_isr':
drivers/i2c/busses/i2c-sh_mobile.c:399:26: warning: 'data' may be used uninitialized in this function [-Wmaybe-uninitialized]
Though the code looks okay and shouldn't ever use the variable
uninitialized. Fix the warning by moving the code around and getting rid
of 'data'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: minor updates to commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Call the function to instantiate SPD EEPROMs automatically on the
main SMBus controller.
Multiplexed SMBus systems are excluded for now as they are more
complex to handle.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In simple cases we can instantiate SPD EEPROMs on the SMBus
automatically. Start with just DDR2, DDR3 and DDR4 on x86 for now,
and only for systems with no more than 4 memory slots. These
limitations may be lifted later.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[wsa: minor change for new API]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Support for 16-bit addresses has been added, so remove it from the todo
list. Also, in the introductory sentence, may clear we talk about "slave
IP cores" to make reading easier.
Fixes: 82d5148154 ("i2c-eeprom_slave: Add support for more eeprom models")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We have a kzalloced struct, no need to init to 0.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
acpi_dev_get_resources() does perform the NULL pointer check against
ACPI companion device which is given as function parameter. Thus,
there is no need to duplicate this check in the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
No need to populate a variable if it is used only in debug output which
may get compiled away anyhow.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The function efm32_i2c_probe() is only called with an
openfirmware platform device.Therefore there is no need
to check that it has an openfirmware node.
Signed-off-by: Shengju Zhang <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In the function efm32_i2c_probe(),when get irq failed,the function
platform_get_irq() logs an error message,so remove redundant message
here.
Signed-off-by: Shengju Zhang <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It's not clear why the commit fe20ff5c7e
("i2c-designware: Add support for Designware core behind PCI devices.")
followed by commit b61b14154b
("i2c-designware: add support for Intel Lynxpoint")
chose to hard code FIFO depth size. The FIFO depth on all hardware,
I have tested on, can be nicely detected automatically.
Thus, we may safely drop hard coded FIFO sizes from the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
PCI devices may have been backed with ACPI handle which supplies
an additional information to the drivers, such as counters.
Call for ACPI configuration from PCI driver in order to utilize counters
provided by ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
For possible code reuse in the future, move ACPI parts into common module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We may bailout directly from the loop instead of breaking it and
testing a loop counter. This also gives advantages such as decreased
indentation level along with dropped unneeded condition.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In order to export array supported speed for wider use, move it
to a header along with i2c_dw_validate_speed() helper moved to
a common code.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This header is a user of some generic ones, include them respectively.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Do not spread PCI specifics over common code. It seems to be a layering
violation which can be easily avoided. Refactor PCI driver and drop
PCI specifics from common code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implement generic GPIO-based I2C bus recovery for the PXA I2C driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This includes a few improvements to make the Tegra I2C controller behave
properly on suspend/resume, does a bit of cleanup and adds support for
the VI-variant of the I2C controller that is used primarily for video
capture purposes.
-----BEGIN PGP SIGNATURE-----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=l3ao
-----END PGP SIGNATURE-----
Merge tag 'for-5.8-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into i2c/for-5.8
i2c: tegra: Changes for v5.8-rc1
This includes a few improvements to make the Tegra I2C controller behave
properly on suspend/resume, does a bit of cleanup and adds support for
the VI-variant of the I2C controller that is used primarily for video
capture purposes.
Although in the most platforms, the bus power of i2c
are alway on, some platforms disable the i2c bus power
in order to meet low power request.
We get and enable bulk regulator in i2c adapter device.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Atomic transfers are not only about sending messages like the original
wording suggested. Speak of 'accessing' now like in i2c.h.
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I don't plan to support every EEPROM type, but the 24c512 ones need a
tiny code update, so let's have that upstream.
Reported-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch adds a algorithm to calculate some ac-timing parameters
which can fully meet I2C Spec.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i801_add_mux() fills in the GPIO lookup table by manually populating an
array of gpiod_lookup structures. Use the existing GPIO_LOOKUP() helper
macro instead, to relax a dependency on the gpiod_lookup structure's
member names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20200511145257.22970-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A call to 'i2c_demux_deactivate_master()' is missing in the error handling
path, as already done in the remove function.
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use a mutex to protect access to idev->msg_len, idev->buf, etc. which
are modified by both altr_i2c_xfer_msg() and altr_i2c_isr().
This is the minimal fix for easy backporting. A cleanup to remove the
spinlock will be added later.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_gpiod_get() usually calls gpio_request_enable() for non-strict pinmux
drivers. These puts the pins in GPIO mode, whithout notifying the pinctrl
driver. At this point, the I2C bus no longer owns the pins. To mux the
pins back to the I2C bus, we use the pinctrl driver to change the state
of the pins to GPIO, before using devm_gpiod_get(). After the pins are
received as GPIOs, we switch theer pinctrl state back to the default
one,
Fixes: d3d3fdcc4c ("i2c: at91: implement i2c bus recovery")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Allow slave mode for PCI enumerated devices by calling a common i2c_dw_probe()
instead of i2c_dw_probe_master().
While dropping dependency to platform driver in slave module, move its
configuration section above, closer to core.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As a preparatory patch to support slave mode for PCI enumerated devices rename
i2c_dw_probe() to i2c_dw_probe_master() and split common i2c_dw_probe() as
inline helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since we have available helper to configure master mode, let's use it
in the PCI driver instead of spread open-coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move configuration routines to respective modules, i.e. master and slave.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_ioremap_resource() instead of
platform_get_resource() + devm_ioremap_resource().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Tegra210 has an extra instance of the I2C controller that is in the
domain of host1x and usually used for camera use-cases. The programming
model for the VI variant of the controller is roughly the same as for
the other variants, except that the I2C registers start at an offset
and are spaced further apart. VI I2C also doesn't support slave mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use master-abort to send the stop condition after an address cycle
rather than resetting the controller.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If we timeout during a message transfer, the control register may
contain bits that cause an action to be set. Read-modify-writing the
register leaving these bits set may trigger the hardware to attempt
one of these actions unintentionally.
Always clear these bits when cleaning up after a message or after
a timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove unnecessary show_state() in the loop inside
i2c_pxa_pio_set_master(), which can be unnecessarily verbose.
Remove the i2c_pxa_scream_blue_murder() in i2c_pxa_pio_xfer(), which
will trigger if we are probing the I2C bus and a slave does not
respond; this is a normal event, and not something to report.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ensure that the various timeout messages can identify where in the code
they were produced from to aid debugging.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Running i2cdetect on a PXA I2C adapter is very noisy; it complains
whenever a slave fails to respond to the address cycle. Since it is
normal to probe for slaves in this way, we should not fill the kernel
log. This is especially true with SFP modules that take a while to
respond on the I2C bus, and probing via the I2C bus is the only way to
detect that they are ready.
Fix this by changing the internal transfer return code from I2C_RETRY
to a new NO_SLAVE code (mapped to -ENXIO, as per the I2C documentation
for this condition, but we still return -EREMOTEIO to the I2C stack to
maintain long established driver behaviour.)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Most of i2c_pxa_pio_xfer() and i2c_pxa_xfer() are identical; the only
differences are that i2c_pxa_pio_xfer() may reset the bus, and they
use different underlying transfer functions. The retry loop is the
same. Consolidate these two functions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use a shorter SPDX identifier instead of pasting the whole license.
While here, replace duplicating PCA954x with PCA984x.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
device_create_file() is called the last in ->probe() but pca954x_cleanup(),
which is called earlier in error path, tries to remove never created file.
Move device_remove_file() call outside of pca954x_cleanup() to make it
slightly closer to what pca954x_init() is doing.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Refactor pca954x_irq_handler() to:
- use for_each_set_bit() macro
- use IRQ_RETVAL() macro
Above change makes code easy to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DMA transfer could be completed, but CPU (which handles DMA interrupt)
may get too busy and can't handle the interrupt in a timely manner,
despite of DMA IRQ being raised. In this case the DMA state needs to
synchronized before terminating DMA transfer in order not to miss the
DMA transfer completion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Boot CPU0 always handle I2C interrupt and under some rare circumstances
(like running KASAN + NFS root) it may stuck in uninterruptible state for
a significant time. In this case we will get timeout if I2C transfer is
running on a sibling CPU, despite of IRQ being raised. In order to handle
this rare condition, the IRQ status needs to be checked after completion
timeout.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
One of the I2C controllers on Tegra SoCs is typically connected to a
system PMIC, which provides controls for critical power supplies for
most platforms.
Some drivers, such as PCI, need to disable these regulators during a
very late stage during suspend and resume them at a very early stage
during resume.
To support these use-cases, keep interrupts disabled during suspend/
resume.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depending on the board design, the I2C controllers found on Tegra SoCs
may require pinmuxing in order to function. This is done as part of the
driver's runtime suspend/resume operations. However, the PM core does
not allow devices to go into runtime suspend during system sleep to
avoid potential races with the suspend/resume of their parents.
As a result of this, when Tegra SoCs resume from system suspend, their
I2C controllers may have lost the pinmux state in hardware, whereas the
pinctrl subsystem is not aware of this. To fix this, make sure that if
the I2C controller is not runtime suspended, the runtime suspend code is
still executed in order to disable the module clock (which we don't need
to be enabled during sleep) and set the pinmux to the idle state.
Conversely, make sure that the I2C controller is properly resumed when
waking up from sleep so that pinmux settings are properly restored.
This fixes a bug seen with DDC transactions to an HDMI monitor timing
out when resuming from system suspend.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reverts commit 9f42de8d4e.
It's not safe to use pm_runtime_force_{suspend,resume}(), especially
during the noirq phase of suspend. See also the guidance provided in
commit 1e2ef05bb8 ("PM: Limit race conditions between runtime PM
and system sleep (v2)").
Signed-off-by: Thierry Reding <treding@nvidia.com>
After a transfer timeout, some faulty I2C slave devices might hold down
the SDA pin. We can generate a bus clear command, hoping that the slave
might release the pins.
If the CLEAR command is not supported, we will use gpio recovery, if
available, to reset the bus.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The old email is still active, but for easier handling, I am going to
use my kernel.org address from now on. Also, add a mailmap for the now
defunct Pengutronix address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case of the I2C client exposes the flag I2C_CLIENT_HOST_NOTIFY,
pm_runtime_get_sync is called in order to always keep active the
adapter. However later on, pm_runtime_put_sync is never called
within the function in case of an error. This commit add this
error handling.
Fixes: 72bfcee11c ("i2c: Prevent runtime suspend of adapter when Host Notify is required")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix i2c_pxa_wait_bus_not_busy()'s boundary conditions, so that a
coincidental success and timeout results in the function returning
success.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Clean up decode_bits() to use pr_cont(), and move the newline into the
function rather than at its two callsites. Avoid printing an
unnecessary space before the newline.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The IRQ log output is supposed to appear on a single line. However,
commit 3a2dc1677b ("i2c: pxa: Update debug function to dump more info
on error") resulted in it being printed one-entry-per-line, which is
excessively long.
Fixing this is not a trivial matter; using pr_cont() doesn't work as
the previous dev_dbg() may not have been compiled in, or may be
dynamic.
Since the rest of this function output is at error level, and is also
debug output, promote this to error level as well to avoid this
problem.
Reduce the number of always zero prefix digits to save screen real-
estate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move the ID tables into one place, near the device dependent data.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move driver-private definitions out of the i2c-pxa.h platform data
header file into the driver itself. Nothing outside of the driver
makes use of these constants.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Always set the fm and hs members of struct pxa_reg_layout. These
members are already taking space, we don't need code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add definitions for the bits in the IBMR register, and use them in the
code. This improves readability.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arrange the register field definitions to be grouped together, rather
than the Armada-3700 definitions being separated from the rest of the
definitions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Re-arrange the PXA I2C code to avoid forward declarations, and keep
similar functionality (e.g. the non-IRQ mode support) together. This
improves code readability.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arrange the includes to be in alphabetical order to help avoid
duplicated includes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-pxa does not need linux/sched.h nor linux/time.h includes, so
remove these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-pxa was created before i2c_8bit_addr_from_msg() was implemented,
and used its own i2c_pxa_addr_byte() which is functionally the same.
Sadly, it was never updated to use this new helper. Switch it over.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In i2c_powermac_register_devices(), variable 'found_onyx' is bool and
assigned '0' and 'true' in different places. Use 'false' instead of '0'.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In AST2600 there have a slow peripheral bus between CPU and i2c
controller. Therefore GIC i2c interrupt status clear have delay timing,
when CPU issue write clear i2c controller interrupt status. To avoid
this issue, the driver need have read after write clear at i2c ISR.
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
Signed-off-by: ryan_chen <ryan_chen@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[wsa: added Fixes tag]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The problem is that we dereference "privdata->pci_dev" when we print
the error messages in amd_mp2_pci_init():
dev_err(ndev_dev(privdata), "Failed to enable MP2 PCI device\n");
^^^^^^^^^^^^^^^^^
Fixes: 529766e0a0 ("i2c: Add drivers for the AMD PCIe MP2 I2C controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We want to break with "i" set to zero whether we find the rate we want
or not. In the current code, if we don't find the rate we want then it
exits the loop with "i" set to -1 and results in an array underflow.
Fixes: 09cc9a3bce ("i2c: stm32f7: allows for any bus frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When slave status is I2C_SLAVE_RX_END, generate I2C_SLAVE_STOP
event to i2c_client.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for SMBUS quick command.
SMBUS quick command passes single bit of information to the
slave (target) device. Can be used to turn slave device on or off.
By default i2c_detect tool uses the smbus quick cmd to try and
detect devices. Without this support it will not detect some slaves.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use of_property_read_u32 to read the "reg" and "i2c-address" property
instead of using of_get_property to check the return values.
Signed-off-by: Aishwarya R <aishwaryarj100@gmail.com>
Tested-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The '>' expression itself is bool, no need to convert it to bool again.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If there is no interrupt defined then an error is logged due
to the use of platform_get_irq. The driver handles not having
the interrupt by falling back to polling, therefore make
the appropriate call when claiming it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not limitate to the 3 (100KHz, 400KHz, 1MHz) bus frequency but
instead allows any frequency (if it matches timing requirements).
Depending on the requested frequency, use the spec data from either
Standard, Fast or Fast Plus mode.
Hardcoding of min/max bus frequencies is removed and is instead computed.
The driver do not use anymore speed identifier but instead handle
directly the frequency and figure out the spec data (necessary
for the computation of the timing register) based on the frequency.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not print an error trace when deferring probe for some resource.
Fix as well the error message in case of tx dma_request_chan failure.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BCM2711, supported by ARCH_BCM2835, also has a controller by the
brcmstb driver so let's allow it to be compiled on that platform.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the slave eeprom has a "firmware-name" in devicetree, then pre-load
the data in the eeprom with this file. Otherwise we init the eeprom with
0xFF.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Björn Ardö <bjorn.ardo@axis.com>
[wsa: some cosmetic changes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rename DPM_FLAG_LEAVE_SUSPENDED to DPM_FLAG_MAY_SKIP_RESUME which
matches its purpose more closely.
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
it will print an error message by itself when platform_get_irq()
goes wrong. so don't need dev_err() in here again.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit adds I2C bus support for the Camera Control Interface
(CCI) I2C controller found on the Qualcomm SoC processors. This I2C
controller supports two masters and they are registered to the core.
CCI versions supported in the driver are msm8916, msm8996 and sdm845.
This is a rework of the patch posted by Vinod:
https://patchwork.kernel.org/patch/10569961/
With additional fixes + most of the comments addressed.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[wsa: removed err msg after platform_get_irq]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA transfer could be completed, but CPU (which handles DMA interrupt)
may get too busy and can't handle the interrupt in a timely manner,
despite of DMA IRQ being raised. In this case the DMA state needs to
synchronized before terminating DMA transfer in order not to miss the
DMA transfer completion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Boot CPU0 always handle I2C interrupt and under some rare circumstances
(like running KASAN + NFS root) it may stuck in uninterruptible state for
a significant time. In this case we will get timeout if I2C transfer is
running on a sibling CPU, despite of IRQ being raised. In order to handle
this rare condition, the IRQ status needs to be checked after completion
timeout.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added support for I2C slave functionality
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for High Speed Mode too.
The value for the parameters tSYMBOL and tLOW is taken from DesignWare
DW_apb_i2c Databook v2.01a, section 3.15.4.6. The calculation should
assume higher bus load since it gives slower timing parameter.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Custom parameters for HCNT/LCNT are not available for OF based system.
Thus, we will use existing SCL timing parameter calculation functions
for Fast Mode Plus.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i801_add_mux() fills in the GPIO lookup table by manually populating an
array of gpiod_lookup structures. Use the existing GPIO_LOOKUP() helper
macro instead, to relax a dependency on the gpiod_lookup structure's
member names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When I wanted to print the chosen values to debug output, I concluded
that a helper function to parse one timing would be helpful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20. This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers. I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.
I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel. All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus. I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All in-tree users have been converted to the new i2c_new_scanned_device
function, so remove this deprecated one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
device_property_read_u32() returns errno or 0, so we should use the
integer variable 'ret' and not the u32 'val' to hold the retval.
Fixes: 0560ad5762 ("i2c: altera: Add Altera I2C Controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We already set DPM_FLAG_SMART_PREPARE, so we completely skip all
callbacks (other then prepare) where possible, quoting from
dw_i2c_plat_prepare():
/*
* If the ACPI companion device object is present for this device, it
* may be accessed during suspend and resume of other devices via I2C
* operation regions, so tell the PM core and middle layers to avoid
* skipping system suspend/resume callbacks for it in that case.
*/
return !has_acpi_companion(dev);
Also setting the DPM_FLAG_SMART_SUSPEND will cause acpi_subsys_suspend()
to leave the controller runtime-suspended even if dw_i2c_plat_prepare()
returned 0.
Leaving the controller runtime-suspended normally, when the I2C controller
is suspended during the suspend_late phase, is not an issue because
the pm_runtime_get_sync() done by i2c_dw_xfer() will (runtime-)resume it.
But for dw I2C controllers on Bay- and Cherry-Trail devices acpi_lpss.c
leaves the controller alive until the suspend_noirq phase, because it may
be used by the _PS3 ACPI methods of PCI devices and PCI devices are left
powered on until the suspend_noirq phase.
Between the suspend_late and resume_early phases runtime-pm is disabled.
So for any ACPI I2C OPRegion accesses done after the suspend_late phase,
the pm_runtime_get_sync() done by i2c_dw_xfer() is a no-op and the
controller is left runtime-suspended.
i2c_dw_xfer() has a check to catch this condition (rather then waiting
for the I2C transfer to timeout because the controller is suspended).
acpi_subsys_suspend() leaving the controller runtime-suspended in
combination with an ACPI I2C OPRegion access done after the suspend_late
phase triggers this check, leading to the following error being logged
on a Bay Trail based Lenovo Thinkpad 8 tablet:
[ 93.275882] i2c_designware 80860F41:00: Transfer while suspended
[ 93.275993] WARNING: CPU: 0 PID: 412 at drivers/i2c/busses/i2c-designware-master.c:429 i2c_dw_xfer+0x239/0x280
...
[ 93.276252] Workqueue: kacpi_notify acpi_os_execute_deferred
[ 93.276267] RIP: 0010:i2c_dw_xfer+0x239/0x280
...
[ 93.276340] Call Trace:
[ 93.276366] __i2c_transfer+0x121/0x520
[ 93.276379] i2c_transfer+0x4c/0x100
[ 93.276392] i2c_acpi_space_handler+0x219/0x510
[ 93.276408] ? up+0x40/0x60
[ 93.276419] ? i2c_acpi_notify+0x130/0x130
[ 93.276433] acpi_ev_address_space_dispatch+0x1e1/0x252
...
So since on BYT and CHT platforms we want ACPI I2c OPRegion accesses
to work until the suspend_noirq phase, we need the controller to be
runtime-resumed during the suspend phase if it is runtime-suspended
suspended at that time. This means that we must not set the
DPM_FLAG_SMART_SUSPEND on these platforms.
On BYT and CHT we already have a special ACCESS_NO_IRQ_SUSPEND flag
to make sure the controller stays functional until the suspend_noirq
phase. This commit makes the driver not set the DPM_FLAG_SMART_SUSPEND
flag when that flag is set.
Cc: stable@vger.kernel.org
Fixes: b30f2f6556 ("i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has:
- using defines for bus speeds to avoid mistakes in hardcoded values;
lots of small driver updates because of that. Thanks, Andy!
- API change: i2c_setup_smbus_alert() was renamed to
i2c_new_smbus_alert_device() and returns ERRPTR now. All in-tree
users have been converted
- in the core, a rare race condition when deleting the cdev has been
fixed. Thanks, Kevin!
- lots of driver updates. Thanks, everyone!
I also want to mention: The amount of review and testing tags given
was quite high this time. Thank you to these people, too. I hope we
can keep it like this!"
* 'i2c/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: rcar: clean up after refactoring i2c_timings
macintosh: convert to i2c_new_scanned_device
i2c: drivers: Use generic definitions for bus frequencies
i2c: algo: Use generic definitions for bus frequencies
i2c: stm32f7: switch to I²C generic property parsing
i2c: rcar: Consolidate timings calls in rcar_i2c_clock_calculate()
i2c: core: Allow override timing properties with 0
i2c: core: Provide generic definitions for bus frequencies
i2c: mxs: Use dma_request_chan() instead dma_request_slave_channel()
i2c: imx: remove duplicate print after platform_get_irq()
i2c: designware: Fix spelling typos in the comments
i2c: designware: Discard i2c_dw_read_comp_param() function
i2c: designware: Detect the FIFO size in the common code
i2c: dev: Fix the race between the release of i2c_dev and cdev
i2c: qcom-geni: Drop of_platform.h include
i2c: qcom-geni: Grow a dev pointer to simplify code
i2c: qcom-geni: Let firmware specify irq trigger flags
i2c: stm32f7: do not backup read-only PECR register
i2c: smbus: remove outdated references to irq level triggers
i2c: convert SMBus alert setup function to return an ERRPTR
...
The pointer is not really needed anymore since we have the timings
struct available in the function itself now. Remove the pointer and
access the struct directly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The interrupt is not required so use platform_irq_get_optional() to
avoid error messages like
i2c-pca-platform 22080000.i2c: IRQ index 0 not found
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nvidia card may come with a "phantom" UCSI device, and its driver gets
stuck in probe routine, prevents any system PM operations like suspend.
There's an unaccounted case that the target time can equal to jiffies in
gpu_i2c_check_status(), let's solve that by using readl_poll_timeout()
instead of jiffies comparison functions.
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ajay Gupta <ajayg@nvidia.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since we have generic definitions for bus frequencies, let's use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions: i2c_parse_fw_timings().
While here, replace hard coded values with standard bus frequency definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move i2c_parse_fw_timings() to rcar_i2c_clock_calculate() to consolidate
timings calls in one place.
While here, replace hard coded values with standard bus frequency definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some drivers may allow to override properties with 0 value when defaults
are not in use, thus, replace memset() with corresponding per property
update.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are few maximum bus frequencies being used in the I²C core code.
Provide generic definitions for bus frequencies and use them in the core.
The drivers may use predefined constants where it is appropriate.
Some of them are already using these under slightly different names.
We will convert them later to use newly introduced defines.
Note, the name of modes are chosen to follow well established naming
scheme [1].
These definitions will also help to avoid typos in the numbers that
may lead to subtle errors.
[1]: https://en.wikipedia.org/wiki/I%C2%B2C#Differences_between_modes
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver forgets to disable and unprepare clk when remove.
Add a call to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We don't need dev_err() message because when something goes wrong,
platform_get_irq() has print an error message itself, so we should
remove duplicate dev_err().
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix spelling typos in the comments with help of `codespell`.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no code left in the kernel which would be using the function.
So just remove it.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The problem with detecting the FIFO depth in the platform driver
is that in order to implement this we have to access the controller
IC_COMP_PARAM_1 register. Currently it's done before the
i2c_dw_set_reg_access() method execution, which is errors prone since
the method determines the registers endianness and access mode and we
can't use dw_readl/dw_writel accessors before this information is
retrieved. We also can't move the i2c_dw_set_reg_access() function
invocation to after the master/slave probe functions call (when endianness
and access mode are determined), since the FIFO depth information is used
by them for initializations. So in order to fix the problem we have no
choice but to move the FIFO size detection methods to the common code and
call it at the probe stage.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The struct cdev is embedded in the struct i2c_dev. In the current code,
we would free the i2c_dev struct directly in put_i2c_dev(), but the
cdev is manged by a kobject, and the release of it is not predictable.
So it is very possible that the i2c_dev is freed before the cdev is
entirely released. We can easily get the following call trace with
CONFIG_DEBUG_KOBJECT_RELEASE and CONFIG_DEBUG_OBJECTS_TIMERS enabled.
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38
WARNING: CPU: 19 PID: 1 at lib/debugobjects.c:325 debug_print_object+0xb0/0xf0
Modules linked in:
CPU: 19 PID: 1 Comm: swapper/0 Tainted: G W 5.2.20-yocto-standard+ #120
Hardware name: Marvell OcteonTX CN96XX board (DT)
pstate: 80c00089 (Nzcv daIf +PAN +UAO)
pc : debug_print_object+0xb0/0xf0
lr : debug_print_object+0xb0/0xf0
sp : ffff00001292f7d0
x29: ffff00001292f7d0 x28: ffff800b82151788
x27: 0000000000000001 x26: ffff800b892c0000
x25: ffff0000124a2558 x24: 0000000000000000
x23: ffff00001107a1d8 x22: ffff0000116b5088
x21: ffff800bdc6afca8 x20: ffff000012471ae8
x19: ffff00001168f2c8 x18: 0000000000000010
x17: 00000000fd6f304b x16: 00000000ee79de43
x15: ffff800bc0e80568 x14: 79616c6564203a74
x13: 6e6968207473696c x12: 5f72656d6974203a
x11: ffff0000113f0018 x10: 0000000000000000
x9 : 000000000000001f x8 : 0000000000000000
x7 : ffff0000101294cc x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000001
x3 : 00000000ffffffff x2 : 0000000000000000
x1 : 387fc15c8ec0f200 x0 : 0000000000000000
Call trace:
debug_print_object+0xb0/0xf0
__debug_check_no_obj_freed+0x19c/0x228
debug_check_no_obj_freed+0x1c/0x28
kfree+0x250/0x440
put_i2c_dev+0x68/0x78
i2cdev_detach_adapter+0x60/0xc8
i2cdev_notifier_call+0x3c/0x70
notifier_call_chain+0x8c/0xe8
blocking_notifier_call_chain+0x64/0x88
device_del+0x74/0x380
device_unregister+0x54/0x78
i2c_del_adapter+0x278/0x2d0
unittest_i2c_bus_remove+0x3c/0x80
platform_drv_remove+0x30/0x50
device_release_driver_internal+0xf4/0x1c0
driver_detach+0x58/0xa0
bus_remove_driver+0x84/0xd8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
of_unittest_overlay+0x8d4/0xbe0
of_unittest+0xae8/0xb3c
do_one_initcall+0xac/0x450
do_initcall_level+0x208/0x224
kernel_init_freeable+0x2d8/0x36c
kernel_init+0x18/0x108
ret_from_fork+0x10/0x1c
irq event stamp: 3934661
hardirqs last enabled at (3934661): [<ffff00001009fa04>] debug_exception_exit+0x4c/0x58
hardirqs last disabled at (3934660): [<ffff00001009fb14>] debug_exception_enter+0xa4/0xe0
softirqs last enabled at (3934654): [<ffff000010081d94>] __do_softirq+0x46c/0x628
softirqs last disabled at (3934649): [<ffff0000100b4a1c>] irq_exit+0x104/0x118
This is a common issue when using cdev embedded in a struct.
Fortunately, we already have a mechanism to solve this kind of issue.
Please see commit 233ed09d7f ("chardev: add helper function to
register char devs with a struct device") for more detail.
In this patch, we choose to embed the struct device into the i2c_dev,
and use the API provided by the commit 233ed09d7f to make sure that
the release of i2c_dev and cdev are in sequence.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver doesn't call any DT platform functions like of_platform_*().
Remove the include as it isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some lines are long here. Use a struct dev pointer to shorten lines and
simplify code. The clk_get() call can fail because of EPROBE_DEFER
problems too, so just remove the error print message because it isn't
useful. Finally, platform_get_irq() already prints an error so just
remove that error message.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to force IRQF_TRIGGER_HIGH here as the DT or ACPI tables
should take care of this for us. Just use 0 instead so that we use the
flags from the firmware. Also, remove specify dev_name() for the irq
name so that we can get better information in /proc/interrupts about
which device is generating interrupts.
Cc: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The PECR register provides received packet computed PEC value.
It makes no sense restoring its value after a reset, and anyway,
as read-only register it cannot be restored.
Fixes: ea6dd25dee ("i2c: stm32f7: add PM_SLEEP suspend/resume support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_verify_client() can fail, so we need to put the device when that
happens.
Fixes: 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure notifications")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a GPIO we are trying to use is not available and we are deferring
the probe, don't output an error message.
This seems to have been the intent of commit 05c7477885
("i2c: gpio: Add support for named gpios in DT") but the error was
still output due to not checking the updated 'retdesc'.
Fixes: 05c7477885 ("i2c: gpio: Add support for named gpios in DT")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IRQ levels are now handled within the IRQ core. Remove the forgotten
references from the documentation.
Fixes: 9b9f2b8bc2 ("i2c: i2c-smbus: Use threaded irq for smbalert")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Only few drivers use this call, so drivers and I2C core are converted at
once with this patch. By simply using i2c_new_client_device() instead of
i2c_new_device(), we easily can return an ERRPTR for this function as
well. To make out of tree users aware that something changed, the
function is renamed to i2c_new_smbus_alert_device().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a new stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Defer the initial enabling of the Fast Mode Plus bits after the
stm32f7_i2c_setup_timing call in probe function in order to avoid
enabling them if speed is downgraded.
Clear & restore the Fast Mode Plus bits in the suspend/resume
handlers of the driver.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HDMI blocks in the BCM2771 have an i2c controller to retrieve the
EDID. This block is split into two parts, the BSC and the AUTO_I2C,
lying in two separate register areas.
The AUTO_I2C block has a mailbox-like interface and will take away the
BSC control from the CPU if enabled. However, the BSC is the actually
the same controller than the one supported by the brcmstb driver, and
the AUTO_I2C doesn't really bring any immediate benefit.
Let's use the BSC then, but let's also tie the AUTO_I2C registers with a
separate compatible so that we can enable AUTO_I2C if needed in the
future.
The AUTO_I2C is enabled by default at boot though, so we first need to
release the BSC from the AUTO_I2C control.
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a new API devm_platform_ioremap_resource() to simplify code.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Tested-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Function i2c_dw_pci_remove() -> pci_free_irq_vectors() ->
pci_disable_msi() -> free_msi_irqs() will throw a BUG_ON() for MSI
enabled device since the driver has not released the requested IRQ before
calling the pci_free_irq_vectors().
Here driver requests an IRQ using devm_request_irq() but automatic
release happens only after remove callback. Fix this by explicitly
freeing the IRQ before calling pci_free_irq_vectors().
Fixes: 21aa3983d6 ("i2c: designware-pci: Switch over to MSI interrupts")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Martin noticed that nct6775 driver does not load properly on his system
in v5.4+ kernels. The issue was bisected to commit b84398d6d7 ("i2c:
i801: Use iTCO version 6 in Cannon Lake PCH and beyond") but it is
likely not the culprit because the faulty code has been in the driver
already since commit 9424693035 ("i2c: i801: Create iTCO device on
newer Intel PCHs"). So more likely some commit that added PCI IDs of
recent chipsets made the driver to create the iTCO_wdt device on Martins
system.
The issue was debugged to be PCI configuration access to the PMC device
that is not present. This returns all 1's when read and this caused the
iTCO_wdt driver to accidentally request resourses used by nct6775.
It turns out that the SMI resource is only required for some ancient
systems, not the ones supported by this driver. For this reason do not
populate the SMI resource at all and drop all the related code. The
driver now always populates the main I/O resource and only in case of SPT
(Intel Sunrisepoint) compatible devices it adds another resource for the
NO_REBOOT bit. These two resources are of different types so
platform_get_resource() used by the iTCO_wdt driver continues to find
the both resources at index 0.
Link: https://lore.kernel.org/linux-hwmon/CAM1AHpQ4196tyD=HhBu-2donSsuogabkfP03v1YF26Q7_BgvgA@mail.gmail.com/
Fixes: 9424693035 ("i2c: i801: Create iTCO device on newer Intel PCHs")
[wsa: complete fix needs all of http://patchwork.ozlabs.org/project/linux-i2c/list/?series=160959&state=*]
Reported-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The comment had some flaws which are now fixed:
- the prefix is 'MAC' not 'AAPL'
- no kernel coding style and too short length
- 'we do' instead of 'we to'
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the i2c-stm32f7 controller to become a wakeup-source
of the system. In such case, when a slave is registered to the
I2C controller, receiving a I2C message targeting that registered
slave address wakes up the suspended system.
In order to be able to wake-up, the I2C controller DT node
must have the property wakeup-source defined and a slave
must be registered.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rework the read and write code paths in the driver to support operation
in atomic contexts. To achieve this, the driver must not rely on IRQs
and not call schedule(), e.g. via a sleep routine, in these cases.
With this patch the driver supports normal operation, DMA transfers and
now the polling mode or also called sleep-free or IRQ-less operation. It
makes the code not simpler or easier to read, but atomic I2C transfers
are needed on some hardware configurations, e.g. to trigger reboots on
an external PMIC chip.
Signed-off-by: Stefan Lengfeld <contact@stefanchrist.eu>
[m.felsch@pengutronix.de: integrate https://patchwork.ozlabs.org/patch/1085943/ review feedback]
[m.felsch@pengutronix.de: adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement i2c bus recovery when slaves devices might hold SDA low.
In this case re-assign SCL/SDA to gpios and issue 9 dummy clock pulses
until the slave release SDA.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Factor out 100 from the equation and do 32-bit arithmetic (3 * clk_mhz / 10)
instead of 64-bit.
Notice that clk_mhz is MHz, so the multiplication will never wrap 32 bits
and there is no need for div_u64().
Addresses-Coverity: 1458369 ("Unintentional integer overflow")
Fixes: 0560ad5762 ("i2c: altera: Add Altera I2C Controller driver")
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The printout for txabrt is way too talkative and is highly annoying with
scanning programs like 'i2cdetect'. Reduce it to the minimum, the rest
can be gained by I2C core debugging and datasheet information. Also,
make it a debug printout, it won't help the regular user.
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"i2c core:
- huge improvements and refactorizations of the Linux I2C
documentation (lots of thanks to Luca for doing it and Jean for the
careful review)
- subsystem wide API conversion to i2c_new_client_device()
- remove obsolete parport-light driver
- smaller core updates (removal of 'extern', enabling more compile
testing, use more helper macros)
- and quite a bunch of driver updates (new IDs, simplifications,
better PM, support of atomic transfers and other improvements)
i2c-mux:
- The main feature is the idle-state rework of the pca954x driver
from Biwen Li
at24 driver:
- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25
bindings
- add support for regulator and pm_runtime control"
* 'i2c/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (91 commits)
i2c: cros-ec-tunnel: Fix ACPI identifier
i2c: cros-ec-tunnel: Fix slave device enumeration
i2c: stm32f7: add PM_SLEEP suspend/resume support
i2c: cadence: Fix wording in i2c-cadence driver
i2c: cadence: Fix power management order of operations
i2c: cadence: Fix error printing in case of defer
i2c: cadence: Handle transfer_size rollover
i2c: i801: Add support for Intel Comet Lake PCH-V
docs: i2c: writing-clients: properly name the stop condition
docs: i2c: i2c-protocol: use same wording as smbus-protocol
docs: i2c: rename sections so the overall picture is clearer
docs: i2c: old-module-parameters: use monospace instead of ""
docs: i2c: old-module-parameters: clarify this is for obsolete kernels
docs: i2c: old-module-parameters: fix internal hyperlink
docs: i2c: instantiating-devices: use monospace for sysfs attributes
docs: i2c: instantiating-devices: rearrange static instatiation
docs: i2c: instantiating-devices: fix internal hyperlink
docs: i2c: smbus-protocol: improve I2C Block transactions description
docs: i2c: smbus-protocol: fix punctuation
docs: i2c: smbus-protocol: fix typo
...
Add Hisilicon Hip08-Lite I2C controller clock frequency support
to the ACPI driver for AMD SoCs (APD) and to the Designware I2C
driver (Hanjun Guo).
-----BEGIN PGP SIGNATURE-----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=9BkB
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add Hisilicon Hip08-Lite I2C controller clock frequency support to the
ACPI driver for AMD SoCs (APD) and to the Designware I2C driver
(Hanjun Guo)"
* tag 'acpi-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
i2c: designware: Add ACPI HID for Hisilicon Hip08-Lite I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip08-Lite I2C controller
Add ACPI HID HISI02A3 for Hisilicon Hip08 Lite, which has different
clock frequency from Hip08 for I2C controller.
Tested-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The initial patch was using the incorrect identifier.
Fixes: 9af1563a54 ("i2c: cros-ec-tunnel: Make the device acpi compatible")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During adding of the adapter the slave device registration
use to fail as the acpi companion field was not populated.
Fixes: 9af1563a54 ("i2c: cros-ec-tunnel: Make the device acpi compatible")
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Backup/restore I2C registers as part of the suspend/resume
handlers. The device is marked as suspended to ensure that
transfers are rejected during the suspended period.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix wording based on checkpatch.pl
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
E.g. pm_runtime_set_active must be called while the power
management system is disabled. Fixes extra hanging clk_enable.
Signed-off-by: Topi Kuutela <topi.kuutela@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not print error in case of EPROBE_DEFER.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Under certain conditions, Cadence's I2C controller's transfer_size
register will roll over and generate invalid read transactions. Before
this change, the ISR relied solely on the RXDV bit to determine when to
write more data to the user's buffer. The invalid read data would cause
overruns, smashing stacks and worse.
This change stops the buffer writes to the requested boundary and
reports the error. The controller will be reset so normal transactions
may resume.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> # in a seperate mail
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for Intel Comet Lake PCH-V which is based on Intel Kaby
Lake. Difference between it and other Comet Lake variants is that former
uses previous iTCO version 4 and latter use version 6 like Intel Cannon
Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a statement that is indented one level too deeply, remove
the extraneous tab.
Fixes: b4c119dbc3 ("i2c: xiic: Add timeout to the rx fifo wait loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a spelling mistake in a module parameter description.
Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Update the help text to reflect current support devices:
1. The Exynos high speed I2C driver supports Exynos5 (ARMv7), Exynos5433
and Exynos7 (both ARMv8) SoCs,
2. The S3C I2C driver supports S3C, S5Pv210 and Exynos{3,4,5} SoCs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some of the I2C bus drivers can be compile tested to increase build
coverage. This requires also:
1. Adding dependencies on COMMON_CLK for BCM2835 and Meson I2C
controllers,
2. Adding 'if' conditional to 'default y' so they will not get enabled
by default on all other architectures,
3. Limiting few compile test options to supported architectures (which
provide the readsX()/writesX() primitives).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[wsa: revert chunk for ZX2967. it needs more preparation]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The recommendation is that the set_active should be done
with pm runtime disabled.
Also fix the remove path for clocking.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It's not always the case that clock is already available when i2c
driver get probed at the first time, e.g. the clock is provided by
clock wizard which may be probed after i2c driver. So let's defer
the probe when devm_clk_get() call fails and give it chance to
try later.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add timeout to the rx fifo empty wait loop. Also check for the return
value for xiic_reinit and pass it to xiic_start_xfer.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
size_t should be printed with its own format to be 64-bit friendly and
fix warning when compiling on 64-bit platform (e.g. with COMPILE_TEST):
drivers/i2c/busses/i2c-highlander.c: In function ‘highlander_i2c_smbus_xfer’:
drivers/i2c/busses/i2c-highlander.c:325:22: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pnx.c: In function ‘i2c_pnx_probe’:
drivers/i2c/busses/i2c-pnx.c:737:47: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 5 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pmcmsp.c: In function ‘pmcmsptwi_probe’:
drivers/i2c/busses/i2c-pmcmsp.c:276:25: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 3 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When handling devm_gpiod_get_optional() errors, free the memory already
allocated. This fixes Smatch warnings:
drivers/i2c/busses/i2c-iop3xx.c:437 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
drivers/i2c/busses/i2c-iop3xx.c:442 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
Fixes: fdb7e884ad ("i2c: iop: Use GPIO descriptors")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
iomem pointers should be printed with pointer format to hide the
actual value and fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-stu300.c: In function ‘stu300_wait_while_busy’:
drivers/i2c/busses/i2c-stu300.c:446:76: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is more robust to check completion status in addition to the left time
in a case of DMA transfer because transfer's completion happens in two
phases [one is ISR, other is tasklet] and thus it is possible that DMA is
completed while I2C completion awaiting times out because of the deferred
notification done by the DMA driver. The DMA completion status becomes
100% actual after DMA synchronization. This fixes spurious DMA timeouts
when system is under load.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is possible that I2C could error out in the middle of DMA transfer and
in this case DMA channel needs to be reset, otherwise a follow up transfer
will fail because DMA channel stays blocked.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is nothing to synchronize in regards to memory accesses for PIO
transfers and for DMA transfers the DMA API takes care of the syncing.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA is preferred for a larger transfers, while PIO is preferred for a
smaller transfers to avoid unnecessary DMA overhead. There is no strict
size limitations for the PIO-mode transfers, so let's rename the constant
for clarity.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
System shutdown may happen with interrupts being disabled and in this case
kernel may hang if atomic transfer isn't supported by driver.
There were several occurrences where I found my Nexus 7 completely
discharged despite of being turned off and then one day I spotted this in
the log:
reboot: Power down
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/i2c/i2c-core.h:40 i2c_transfer+0x95/0x9c
No atomic I2C transfer handler for 'i2c-1'
Modules linked in: tegra30_devfreq
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.4.0-next-20191202-00120-gf7ecd80fb803-dirty #3195
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[<c010e4b5>] (unwind_backtrace) from [<c010a0fd>] (show_stack+0x11/0x14)
[<c010a0fd>] (show_stack) from [<c09995e5>] (dump_stack+0x85/0x94)
[<c09995e5>] (dump_stack) from [<c011f3d1>] (__warn+0xc1/0xc4)
[<c011f3d1>] (__warn) from [<c011f691>] (warn_slowpath_fmt+0x61/0x78)
[<c011f691>] (warn_slowpath_fmt) from [<c069a8dd>] (i2c_transfer+0x95/0x9c)
[<c069a8dd>] (i2c_transfer) from [<c05667f1>] (regmap_i2c_read+0x4d/0x6c)
[<c05667f1>] (regmap_i2c_read) from [<c0563601>] (_regmap_raw_read+0x99/0x1cc)
[<c0563601>] (_regmap_raw_read) from [<c0563757>] (_regmap_bus_read+0x23/0x38)
[<c0563757>] (_regmap_bus_read) from [<c056293d>] (_regmap_read+0x3d/0xfc)
[<c056293d>] (_regmap_read) from [<c0562d3b>] (_regmap_update_bits+0x87/0xc4)
[<c0562d3b>] (_regmap_update_bits) from [<c0563add>] (regmap_update_bits_base+0x39/0x50)
[<c0563add>] (regmap_update_bits_base) from [<c056fd39>] (max77620_pm_power_off+0x29/0x2c)
[<c056fd39>] (max77620_pm_power_off) from [<c013bbdd>] (__do_sys_reboot+0xe9/0x170)
[<c013bbdd>] (__do_sys_reboot) from [<c0101001>] (ret_fast_syscall+0x1/0x28)
Exception stack(0xde907fa8 to 0xde907ff0)
7fa0: 00000000 00000000 fee1dead 28121969 4321fedc 00000000
7fc0: 00000000 00000000 00000000 00000058 00000000 00000000 00000000 00000000
7fe0: 0045adf0 bed9abb8 004444a0 b6c666d0
---[ end trace bdd18f87595b1a5e ]---
The atomic transferring is implemented by enforcing PIO mode for the
transfer and by polling interrupt status until transfer is completed or
failed.
Now system shuts down properly every time.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Potentially it is possible that interrupt may fire after transfer timeout.
That may not end up well for the next transfer because interrupt handling
may race with hardware resetting.
This is very unlikely to happen in practice, but anyway let's prevent the
potential problem by enabling interrupt only at the moments when it is
actually necessary to get some interrupt event.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After removal of the parport-light driver, this include is used by the
parport driver exclusively and can be included in the main source. Move
module parameter declarations to its variable declaration while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver is not 'new' anymore, so remove details from the driver it
surpassed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The justification of a light version of the parport driver was less
overhead for embedded systems. Well, today, even if an embedded system
still has a parport, it surely can handle the fully-fledged parport
driver. Remove it to reduce the maintenance burden.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
One of the recent Tegra I2C commits made a change that resumes runtime PM
during driver's probe, but it missed to put the RPM in a case of error.
Note that it's not correct to use pm_runtime_status_suspended because it
breaks RPM refcounting.
Fixes: 8ebf15e9c8 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I noticed that sometime I2C clock is kept enabled during suspend-resume.
This happens because runtime PM defers dynamic suspension and thus it may
happen that runtime PM is in active state when system enters into suspend.
In particular I2C controller that is used for CPU's DVFS is often kept ON
during suspend because CPU's voltage scaling happens quite often.
Fixes: 8ebf15e9c8 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Boards with some of the 32-bit SoCs (mostly Meson8 and Meson8m2) use a
Ricoh RN5T618 PMU which acts as system power controller. The driver for
the system power controller may need to the I2C bus just before shutting
down or rebooting the system. At this stage the interrupts may be
disabled already.
Implement the master_xfer_atomic callback so the driver for the RN5T618
PMU can communicate properly with the PMU when shutting down or
rebooting the board. The CTRL register has a status bit which can be
polled to determine when processing has completed. According to the
public S805 datasheet the value 0 means "idle" and 1 means "running".
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[wsa: converted some whitespace alignment]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C specification states that tsu:sto for standard mode timing must
be at minimum 4us. Pictographically, this is:
SCL: ____/~~~~~~~~~
SDA: _________/~~~~
->| |<- 4us minimum
We are currently waiting 2.5us between asserting SCL and SDA, which is
in violation of the standard. Adjust the timings to ensure that we meet
what is stipulated as the minimum timings to ensure that all devices
correctly interpret the STOP bus transition.
This is more important than trying to generate a square wave with even
duty cycle.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit bebff81fb8 ("i2c: bcm2835: Model Divider in CCF") introduced
a NULL pointer dereference on driver unload. It seems that we can't fetch
the bus clock via devm_clk_get in bcm2835_i2c_remove. As an alternative
approach store a pointer to the bus clock in the private driver structure.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for probing i2c driver on the X1000 Soc from Ingenic.
call the corresponding fifo parameter according to the device
model obtained from the devicetree.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch changes the I2C fault codes according to the specified
values in Documentation/i2c/fault-codes.
Signed-off-by: Christoph Müllner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Platform data structs are initialized by default with zero values.
Thus it becomes redundant to initialize them manually to zero (false).
Remove extra false initialization for field members in structs.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In SAM9X60 datasheet, FLEX_TWI_CWGR register description mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).
This is the same offset as in SAMA5D2.
Fixes: b002779237 ("i2c: at91: add new platform support for sam9x60")
Suggested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This supports property idle-state,if present,
overrides i2c-mux-idle-disconnect.
My use cases:
- Use the property idle-state to fix
an errata on LS2085ARDB and LS2088ARDB.
- Errata id: E-00013(board LS2085ARDB and
LS2088ARDB revision on Rev.B, Rev.C and Rev.D).
- About E-00013:
- Description: I2C1 and I2C3 buses
are missing pull-up.
- Impact: When the PCA954x device is tri-stated, the I2C bus
will float. This makes the I2C bus and its associated
downstream devices inaccessible.
- Hardware fix: Populate resistors R189 and R190 for I2C1
and resistors R228 and R229 for I2C3.
- Software fix: Remove the tri-state option from the PCA954x
driver(PCA954x always on enable status, specify a
channel zero in dts to fix the errata E-00013).
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Because it looks nice!
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Convert the i2c core sysfs attributes from DEVICE_ATTR() to
DEVICE_ATTR_*(), to reduce boilerplate.
This requires renaming some functions.
Although no suitable macro exists for the delete_device attribute,
rename i2c_sysfs_delete_device() to delete_device_store() for
consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All in-kernel users have been converted to
{devm_}i2c_new_dummy_device(). Remove the old API.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
Move from the deprecated i2c_new_probed_device() to the new
i2c_new_scanned_device(). Make use of the new ERRPTR if suitable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Max Staudt <max@enpas.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
