mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-14 17:57:05 +07:00
arm64: dts: qcom: sbc: Name GPIO lines
This names the GPIO lines on the APQ8016 "SBC" also known as the DragonBoard 410c, according to the schematic. This is necessary for a conforming userspace looking across all GPIO chips for the GPIO lines named "GPIO-A" thru "GPIO-L". Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
This commit is contained in:
Linus Walleij
Andy Gross
parent
2f8d2931be
commit
f6b1674d57
@ -19,6 +19,30 @@
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/sound/apq8016-lpass.h>
|
||||
|
||||
/*
|
||||
* GPIO name legend: proper name = the GPIO line is used as GPIO
|
||||
* NC = not connected (pin out but not routed from the chip to
|
||||
* anything the board)
|
||||
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
|
||||
* LSEC = Low Speed External Connector
|
||||
* HSEC = High Speed External Connector
|
||||
*
|
||||
* Line names are taken from the schematic "DragonBoard410c"
|
||||
* dated monday, august 31, 2015. Page 5 in particular.
|
||||
*
|
||||
* For the lines routed to the external connectors the
|
||||
* lines are named after the 96Boards CE Specification 1.0,
|
||||
* Appendix "Expansion Connector Signal Description".
|
||||
*
|
||||
* When the 96Board naming of a line and the schematic name of
|
||||
* the same line are in conflict, the 96Board specification
|
||||
* takes precedence, which means that the external UART on the
|
||||
* LSEC is named UART0 while the schematic and SoC names this
|
||||
* UART3. This is only for the informational lines i.e. "[FOO]",
|
||||
* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
|
||||
* ones actually used for GPIO.
|
||||
*/
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
serial0 = &blsp1_uart2;
|
||||
@ -47,6 +71,132 @@ ramoops@bff00000{
|
||||
};
|
||||
|
||||
soc {
|
||||
pinctrl@1000000 {
|
||||
gpio-line-names =
|
||||
"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
|
||||
"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
|
||||
"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
|
||||
"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
|
||||
"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
|
||||
"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
|
||||
"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
|
||||
"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
|
||||
"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
|
||||
"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
|
||||
"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
|
||||
"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
|
||||
"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
|
||||
"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
|
||||
"[I2C3_SDA]", /* HSEC pin 38 */
|
||||
"[I2C3_SCL]", /* HSEC pin 36 */
|
||||
"[SPI0_MOSI]", /* LSEC pin 14 */
|
||||
"[SPI0_MISO]", /* LSEC pin 10 */
|
||||
"[SPI0_CS_N]", /* LSEC pin 12 */
|
||||
"[SPI0_CLK]", /* LSEC pin 8 */
|
||||
"HDMI_HPD_N", /* GPIO 20 */
|
||||
"USR_LED_1_CTRL",
|
||||
"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
|
||||
"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
|
||||
"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
|
||||
"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
|
||||
"[CSI0_MCLK]", /* HSEC pin 15 */
|
||||
"[CSI1_MCLK]", /* HSEC pin 17 */
|
||||
"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
|
||||
"[I2C2_SDA]", /* HSEC pin 34 */
|
||||
"[I2C2_SCL]", /* HSEC pin 32 */
|
||||
"DSI2HDMI_INT_N",
|
||||
"DSI_SW_SEL_APQ",
|
||||
"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
|
||||
"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
|
||||
"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
|
||||
"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
|
||||
"FORCED_USB_BOOT",
|
||||
"SD_CARD_DET_N",
|
||||
"[WCSS_BT_SSBI]",
|
||||
"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
|
||||
"[WCSS_WLAN_DATA_1]",
|
||||
"[WCSS_WLAN_DATA_0]",
|
||||
"[WCSS_WLAN_SET]",
|
||||
"[WCSS_WLAN_CLK]",
|
||||
"[WCSS_FM_SSBI]",
|
||||
"[WCSS_FM_SDI]",
|
||||
"[WCSS_BT_DAT_CTL]",
|
||||
"[WCSS_BT_DAT_STB]",
|
||||
"NC",
|
||||
"NC", /* GPIO 50 */
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC", /* GPIO 60 */
|
||||
"NC",
|
||||
"NC",
|
||||
"[CDC_PDM0_CLK]",
|
||||
"[CDC_PDM0_SYNC]",
|
||||
"[CDC_PDM0_TX0]",
|
||||
"[CDC_PDM0_RX0]",
|
||||
"[CDC_PDM0_RX1]",
|
||||
"[CDC_PDM0_RX2]",
|
||||
"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
|
||||
"NC", /* GPIO 70 */
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC", /* GPIO 74 */
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"BOOT_CONFIG_0", /* GPIO 80 */
|
||||
"BOOT_CONFIG_1",
|
||||
"BOOT_CONFIG_2",
|
||||
"BOOT_CONFIG_3",
|
||||
"NC",
|
||||
"NC",
|
||||
"BOOT_CONFIG_5",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC", /* GPIO 90 */
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"NC", /* GPIO 100 */
|
||||
"NC",
|
||||
"NC",
|
||||
"NC",
|
||||
"SSBI_GPS",
|
||||
"NC",
|
||||
"NC",
|
||||
"KEY_VOLP_N",
|
||||
"NC",
|
||||
"NC",
|
||||
"[LS_EXP_MI2S_WS]", /* GPIO 110 */
|
||||
"NC",
|
||||
"NC",
|
||||
"[LS_EXP_MI2S_SCK]",
|
||||
"[LS_EXP_MI2S_DATA0]",
|
||||
"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
|
||||
"NC",
|
||||
"[DSI2HDMI_MI2S_WS]",
|
||||
"[DSI2HDMI_MI2S_SCK]",
|
||||
"[DSI2HDMI_MI2S_DATA0]",
|
||||
"USR_LED_2_CTRL", /* GPIO 120 */
|
||||
"SB_HS_ID";
|
||||
};
|
||||
|
||||
dma@7884000 {
|
||||
status = "okay";
|
||||
};
|
||||
@ -329,6 +479,25 @@ codec {
|
||||
};
|
||||
};
|
||||
|
||||
spmi@200f000 {
|
||||
pm8916@0 {
|
||||
gpios@c000 {
|
||||
gpio-line-names =
|
||||
"USR_LED_3_CTRL",
|
||||
"USR_LED_4_CTRL",
|
||||
"USB_HUB_RESET_N_PM",
|
||||
"USB_SW_SEL_PM";
|
||||
};
|
||||
mpps@a000 {
|
||||
gpio-line-names =
|
||||
"VDD_PX_BIAS",
|
||||
"WLAN_LED_CTRL",
|
||||
"BT_LED_CTRL",
|
||||
"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
wcnss@a21b000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
Loading…
Reference in New Issue
Block a user