mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 20:47:12 +07:00
ARM: dts: at91: at91sam9xx5ek: Style cleanup
- newline between properties and sub-nodes - use tags from included dtsi instead of duplicating the hierarchy There are no differences in the generated .dtbs Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Link: https://lore.kernel.org/r/20190812212757.23432-7-uwe@kleine-koenig.org Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This commit is contained in:
Uwe Kleine-König
Alexandre Belloni
parent
c1ad3ffb18
commit
b222de0242
@ -14,14 +14,6 @@ / {
|
||||
model = "Atmel AT91SAM9G15-EK";
|
||||
compatible = "atmel,at91sam9g15ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
hlcdc: hlcdc@f8038000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
backlight: backlight {
|
||||
status = "okay";
|
||||
};
|
||||
@ -38,3 +30,7 @@ panel_reg: panel_regulator {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&hlcdc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -12,57 +12,54 @@
|
||||
/ {
|
||||
model = "Atmel AT91SAM9G25-EK";
|
||||
compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
|
||||
};
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
spi0: spi@f0000000 {
|
||||
status = "disabled";
|
||||
};
|
||||
&i2c0 {
|
||||
camera@30 {
|
||||
compatible = "ovti,ov2640";
|
||||
reg = <0x30>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
|
||||
resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
|
||||
pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
|
||||
clocks = <&pmc PMC_TYPE_SYSTEM 8>;
|
||||
clock-names = "xvclk";
|
||||
assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>;
|
||||
assigned-clock-rates = <25000000>;
|
||||
status = "okay";
|
||||
|
||||
mmc1: mmc@f000c000 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
i2c0: i2c@f8010000 {
|
||||
ov2640: camera@30 {
|
||||
compatible = "ovti,ov2640";
|
||||
reg = <0x30>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
|
||||
resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
|
||||
pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
|
||||
clocks = <&pmc PMC_TYPE_SYSTEM 8>;
|
||||
clock-names = "xvclk";
|
||||
assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>;
|
||||
assigned-clock-rates = <25000000>;
|
||||
status = "okay";
|
||||
|
||||
port {
|
||||
ov2640_0: endpoint {
|
||||
remote-endpoint = <&isi_0>;
|
||||
bus-width = <8>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
macb0: ethernet@f802c000 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
isi: isi@f8048000 {
|
||||
status = "okay";
|
||||
port {
|
||||
isi_0: endpoint@0 {
|
||||
reg = <0>;
|
||||
remote-endpoint = <&ov2640_0>;
|
||||
bus-width = <8>;
|
||||
vsync-active = <1>;
|
||||
hsync-active = <1>;
|
||||
};
|
||||
};
|
||||
port {
|
||||
ov2640_0: endpoint {
|
||||
remote-endpoint = <&isi_0>;
|
||||
bus-width = <8>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&isi {
|
||||
status = "okay";
|
||||
|
||||
port {
|
||||
isi_0: endpoint@0 {
|
||||
reg = <0>;
|
||||
remote-endpoint = <&ov2640_0>;
|
||||
bus-width = <8>;
|
||||
vsync-active = <1>;
|
||||
hsync-active = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&macb0 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
@ -14,19 +14,6 @@ / {
|
||||
model = "Atmel AT91SAM9G35-EK";
|
||||
compatible = "atmel,at91sam9g35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
macb0: ethernet@f802c000 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
hlcdc: hlcdc@f8038000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
backlight: backlight {
|
||||
status = "okay";
|
||||
};
|
||||
@ -43,3 +30,12 @@ panel_reg: panel_regulator {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&hlcdc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&macb0 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -12,28 +12,24 @@
|
||||
/ {
|
||||
model = "Atmel AT91SAM9X25-EK";
|
||||
compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
can1: can@f8004000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
macb0: ethernet@f802c000 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
macb1: ethernet@f8030000 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
pwm0: pwm@f8034000 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm0_pwm0_1>;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&can1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&macb0 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&macb1 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwm0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm0_pwm0_1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -13,32 +13,29 @@
|
||||
/ {
|
||||
model = "Atmel AT91SAM9X35-EK";
|
||||
compatible = "atmel,at91sam9x35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
macb0: ethernet@f802c000 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
hlcdc: hlcdc@f8038000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
backlight: backlight {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
bl_reg: backlight_regulator {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
panel: panel {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
panel_reg: panel_regulator {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&backlight {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&bl_reg {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hlcdc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&macb0 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&panel {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&panel_reg {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -16,139 +16,6 @@ chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
mmc0: mmc@f0008000 {
|
||||
pinctrl-0 = <
|
||||
&pinctrl_board_mmc0
|
||||
&pinctrl_mmc0_slot0_clk_cmd_dat0
|
||||
&pinctrl_mmc0_slot0_dat1_3>;
|
||||
status = "okay";
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
mmc1: mmc@f000c000 {
|
||||
pinctrl-0 = <
|
||||
&pinctrl_board_mmc1
|
||||
&pinctrl_mmc1_slot0_clk_cmd_dat0
|
||||
&pinctrl_mmc1_slot0_dat1_3>;
|
||||
status = "okay";
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
dbgu: serial@fffff200 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usart0: serial@f801c000 {
|
||||
atmel,use-dma-rx;
|
||||
atmel,use-dma-tx;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb2: gadget@f803c000 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_board_usb2>;
|
||||
atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
i2c0: i2c@f8010000 {
|
||||
status = "okay";
|
||||
|
||||
wm8731: wm8731@1a {
|
||||
compatible = "wm8731";
|
||||
reg = <0x1a>;
|
||||
};
|
||||
};
|
||||
|
||||
adc0: adc@f804c000 {
|
||||
atmel,adc-ts-wires = <4>;
|
||||
atmel,adc-ts-pressure-threshold = <10000>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
pinctrl@fffff400 {
|
||||
camera_sensor {
|
||||
pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 {
|
||||
atmel,pins =
|
||||
<AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_MCK */
|
||||
};
|
||||
|
||||
pinctrl_sensor_power: sensor_power-0 {
|
||||
atmel,pins =
|
||||
<AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
|
||||
};
|
||||
|
||||
pinctrl_sensor_reset: sensor_reset-0 {
|
||||
atmel,pins =
|
||||
<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
|
||||
};
|
||||
};
|
||||
|
||||
mmc0 {
|
||||
pinctrl_board_mmc0: mmc0-board {
|
||||
atmel,pins =
|
||||
<AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
|
||||
};
|
||||
};
|
||||
|
||||
mmc1 {
|
||||
pinctrl_board_mmc1: mmc1-board {
|
||||
atmel,pins =
|
||||
<AT91_PIOD 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD14 gpio CD pin pull up and deglitch */
|
||||
};
|
||||
};
|
||||
|
||||
usb2 {
|
||||
pinctrl_board_usb2: usb2-board {
|
||||
atmel,pins =
|
||||
<AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio vbus sense, deglitch */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
spi0: spi@f0000000 {
|
||||
status = "disabled"; /* conflicts with mmc1 */
|
||||
cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
|
||||
m25p80@0 {
|
||||
compatible = "atmel,at25df321a";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog@fffffe40 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ssc0: ssc@f0010000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
usb0: ohci@600000 {
|
||||
status = "okay";
|
||||
num-ports = <3>;
|
||||
atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
|
||||
&pioD 19 GPIO_ACTIVE_LOW
|
||||
&pioD 20 GPIO_ACTIVE_LOW
|
||||
>;
|
||||
};
|
||||
|
||||
usb1: ehci@700000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
sound {
|
||||
compatible = "atmel,sam9x5-wm8731-audio";
|
||||
|
||||
@ -164,3 +31,135 @@ sound {
|
||||
atmel,audio-codec = <&wm8731>;
|
||||
};
|
||||
};
|
||||
|
||||
&adc0 {
|
||||
atmel,adc-ts-wires = <4>;
|
||||
atmel,adc-ts-pressure-threshold = <10000>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dbgu {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
|
||||
wm8731: wm8731@1a {
|
||||
compatible = "wm8731";
|
||||
reg = <0x1a>;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc0 {
|
||||
pinctrl-0 = <
|
||||
&pinctrl_board_mmc0
|
||||
&pinctrl_mmc0_slot0_clk_cmd_dat0
|
||||
&pinctrl_mmc0_slot0_dat1_3>;
|
||||
status = "okay";
|
||||
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
pinctrl-0 = <
|
||||
&pinctrl_board_mmc1
|
||||
&pinctrl_mmc1_slot0_clk_cmd_dat0
|
||||
&pinctrl_mmc1_slot0_dat1_3>;
|
||||
status = "okay";
|
||||
|
||||
slot@0 {
|
||||
reg = <0>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
camera_sensor {
|
||||
pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 {
|
||||
atmel,pins =
|
||||
<AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_MCK */
|
||||
};
|
||||
|
||||
pinctrl_sensor_power: sensor_power-0 {
|
||||
atmel,pins =
|
||||
<AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
|
||||
};
|
||||
|
||||
pinctrl_sensor_reset: sensor_reset-0 {
|
||||
atmel,pins =
|
||||
<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
|
||||
};
|
||||
};
|
||||
|
||||
mmc0 {
|
||||
pinctrl_board_mmc0: mmc0-board {
|
||||
atmel,pins =
|
||||
<AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
|
||||
};
|
||||
};
|
||||
|
||||
mmc1 {
|
||||
pinctrl_board_mmc1: mmc1-board {
|
||||
atmel,pins =
|
||||
<AT91_PIOD 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD14 gpio CD pin pull up and deglitch */
|
||||
};
|
||||
};
|
||||
|
||||
usb2 {
|
||||
pinctrl_board_usb2: usb2-board {
|
||||
atmel,pins =
|
||||
<AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio vbus sense, deglitch */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
|
||||
status = "disabled"; /* conflicts with mmc1 */
|
||||
|
||||
m25p80@0 {
|
||||
compatible = "atmel,at25df321a";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&ssc0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usart0 {
|
||||
atmel,use-dma-rx;
|
||||
atmel,use-dma-tx;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
num-ports = <3>;
|
||||
atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
|
||||
&pioD 19 GPIO_ACTIVE_LOW
|
||||
&pioD 20 GPIO_ACTIVE_LOW
|
||||
>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_board_usb2>;
|
||||
atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
Loading…
Reference in New Issue
Block a user