Merge branch 'bcmgenet'

Florian Fainelli says: ==================== Support for the Broadcom GENET driver This patchset adds support for the Broadcom GENET Gigabit Ethernet MAC controller. This controller is found on the Broadcom BCM7xxx Set Top Box System-on-a-chips. Changes since v4: - add dependency on CONFIG_OF Changes since v3: - fixed Kconfig dependency on FIXED_PHY Changes since v2: - dropped the patch that adds an "internal" phy-mode ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2024-12-28 07:05:12 +07:00 · 2014-02-14 00:28:30 -05:00 · 2014-02-14 00:28:30 -05:00 · a56cddd8dc
commit a56cddd8dc
parent c045a734da 32ec90d5d5
15 changed files with 4247 additions and 53 deletions
--- a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt
+++ b/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt
@ -0,0 +1,121 @@
+* Broadcom BCM7xxx Ethernet Controller (GENET)
+
+Required properties:
+- compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2",
+  "brcm,genet-v3", "brcm,genet-v4".
+- reg: address and length of the register set for the device
+- interrupts: must be two cells, the first cell is the general purpose
+  interrupt line, while the second cell is the interrupt for the ring
+  RX and TX queues operating in ring mode
+- phy-mode: String, operation mode of the PHY interface. Supported values are
+  "mii", "rgmii", "rgmii-txid", "rev-mii", "moca". Analogous to ePAPR
+  "phy-connection-type" values
+- address-cells: should be 1
+- size-cells: should be 1
+
+Optional properties:
+- clocks: When provided, must be two cells, first one is the main GENET clock
+  and the second cell is the Genet Wake-on-LAN clock.
+
+- phy-handle: A phandle to a phy node defining the PHY address (as the reg
+  property, a single integer), used to describe configurations where a PHY
+  (internal or external) is used.
+
+- fixed-link: When the GENET interface is connected to a MoCA hardware block or
+  when operating in a RGMII to RGMII type of connection, or when the MDIO bus is
+  voluntarily disabled, this property should be used to describe the "fixed link".
+  See Documentation/devicetree/bindings/net/fsl-tsec-phy.txt for information on
+  the property specifics
+
+Required child nodes:
+
+- mdio bus node: this node should always be present regarless of the PHY
+  configuration of the GENET instance
+
+MDIO bus node required properties:
+
+- compatible: should contain one of "brcm,genet-mdio-v1", "brcm,genet-mdio-v2"
+  "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", the version has to match the
+  parent node compatible property (e.g: brcm,genet-v4 pairs with
+  brcm,genet-mdio-v4)
+- reg: address and length relative to the parent node base register address
+- address-cells: address cell for MDIO bus addressing, should be 1
+- size-cells: size of the cells for MDIO bus addressing, should be 0
+
+Ethernet PHY node properties:
+
+See Documentation/devicetree/bindings/net/phy.txt for the list of required and
+optional properties.
+
+Internal Gigabit PHY example:
+
+ethernet@f0b60000 {
+	phy-mode = "internal";
+	phy-handle = <&phy1>;
+	mac-address = [ 00 10 18 36 23 1a ];
+	compatible = "brcm,genet-v4";
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	reg = <0xf0b60000 0xfc4c>;
+	interrupts = <0x0 0x14 0x0>, <0x0 0x15 0x0>;
+
+	mdio@e14 {
+		compatible = "brcm,genet-mdio-v4";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		reg = <0xe14 0x8>;
+
+		phy1: ethernet-phy@1 {
+			max-speed = <1000>;
+			reg = <0x1>;
+			compatible = "brcm,28nm-gphy", "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};
+
+MoCA interface / MAC to MAC example:
+
+ethernet@f0b80000 {
+	phy-mode = "moca";
+	fixed-link = <1 0 1000 0 0>;
+	mac-address = [ 00 10 18 36 24 1a ];
+	compatible = "brcm,genet-v4";
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	reg = <0xf0b80000 0xfc4c>;
+	interrupts = <0x0 0x16 0x0>, <0x0 0x17 0x0>;
+
+	mdio@e14 {
+		compatible = "brcm,genet-mdio-v4";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		reg = <0xe14 0x8>;
+	};
+};
+
+
+External MDIO-connected Gigabit PHY/switch:
+
+ethernet@f0ba0000 {
+	phy-mode = "rgmii";
+	phy-handle = <&phy0>;
+	mac-address = [ 00 10 18 36 26 1a ];
+	compatible = "brcm,genet-v4";
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	reg = <0xf0ba0000 0xfc4c>;
+	interrupts = <0x0 0x18 0x0>, <0x0 0x19 0x0>;
+
+	mdio@0e14 {
+		compatible = "brcm,genet-mdio-v4";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		reg = <0xe14 0x8>;
+
+		phy0: ethernet-phy@0 {
+			max-speed = <1000>;
+			reg = <0x0>;
+			compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};
--- a/6
+++ b/6
@ -1845,6 +1845,12 @@ L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/broadcom/b44.*

+BROADCOM GENET ETHERNET DRIVER
+M:	Florian Fainelli <f.fainelli@gmail.com>
+L:	netdev@vger.kernel.org
+S:	Supported
+F:	drivers/net/ethernet/broadcom/genet/
+
 BROADCOM BNX2 GIGABIT ETHERNET DRIVER
 M:	Michael Chan <mchan@broadcom.com>
 L:	netdev@vger.kernel.org
--- a/drivers/net/ethernet/broadcom/Kconfig
+++ b/drivers/net/ethernet/broadcom/Kconfig
@ -60,6 +60,17 @@ config BCM63XX_ENET
 	  This driver supports the ethernet MACs in the Broadcom 63xx
 	  MIPS chipset family (BCM63XX).

+config BCMGENET
+	tristate "Broadcom GENET internal MAC support"
+	depends on OF
+	select MII
+	select PHYLIB
+	select FIXED_PHY if BCMGENET=y
+	select BCM7XXX_PHY
+	help
+	  This driver supports the built-in Ethernet MACs found in the
+	  Broadcom BCM7xxx Set Top Box family chipset.
+
 config BNX2
 	tristate "Broadcom NetXtremeII support"
 	depends on PCI
--- a/drivers/net/ethernet/broadcom/Makefile
+++ b/drivers/net/ethernet/broadcom/Makefile
@ -4,6 +4,7 @@

 obj-$(CONFIG_B44) += b44.o
 obj-$(CONFIG_BCM63XX_ENET) += bcm63xx_enet.o
+obj-$(CONFIG_BCMGENET) += genet/
 obj-$(CONFIG_BNX2) += bnx2.o
 obj-$(CONFIG_CNIC) += cnic.o
 obj-$(CONFIG_BNX2X) += bnx2x/
--- a/drivers/net/ethernet/broadcom/genet/Makefile
+++ b/drivers/net/ethernet/broadcom/genet/Makefile
@ -0,0 +1,2 @@
+obj-$(CONFIG_BCMGENET) += genet.o
+genet-objs := bcmgenet.o bcmmii.o
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.h
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
@ -0,0 +1,630 @@
+/*
+ * Copyright (c) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ *
+*/
+#ifndef __BCMGENET_H__
+#define __BCMGENET_H__
+
+#include <linux/skbuff.h>
+#include <linux/netdevice.h>
+#include <linux/spinlock.h>
+#include <linux/clk.h>
+#include <linux/mii.h>
+#include <linux/if_vlan.h>
+#include <linux/phy.h>
+
+/* total number of Buffer Descriptors, same for Rx/Tx */
+#define TOTAL_DESC				256
+
+/* which ring is descriptor based */
+#define DESC_INDEX				16
+
+/* Body(1500) + EH_SIZE(14) + VLANTAG(4) + BRCMTAG(6) + FCS(4) = 1528.
+ * 1536 is multiple of 256 bytes
+ */
+#define ENET_BRCM_TAG_LEN	6
+#define ENET_PAD		8
+#define ENET_MAX_MTU_SIZE	(ETH_DATA_LEN + ETH_HLEN + VLAN_HLEN + \
+				 ENET_BRCM_TAG_LEN + ETH_FCS_LEN + ENET_PAD)
+#define DMA_MAX_BURST_LENGTH    0x10
+
+/* misc. configuration */
+#define CLEAR_ALL_HFB			0xFF
+#define DMA_FC_THRESH_HI		(TOTAL_DESC >> 4)
+#define DMA_FC_THRESH_LO		5
+
+/* 64B receive/transmit status block */
+struct status_64 {
+	u32	length_status;		/* length and peripheral status */
+	u32	ext_status;		/* Extended status*/
+	u32	rx_csum;		/* partial rx checksum */
+	u32	unused1[9];		/* unused */
+	u32	tx_csum_info;		/* Tx checksum info. */
+	u32	unused2[3];		/* unused */
+};
+
+/* Rx status bits */
+#define STATUS_RX_EXT_MASK		0x1FFFFF
+#define STATUS_RX_CSUM_MASK		0xFFFF
+#define STATUS_RX_CSUM_OK		0x10000
+#define STATUS_RX_CSUM_FR		0x20000
+#define STATUS_RX_PROTO_TCP		0
+#define STATUS_RX_PROTO_UDP		1
+#define STATUS_RX_PROTO_ICMP		2
+#define STATUS_RX_PROTO_OTHER		3
+#define STATUS_RX_PROTO_MASK		3
+#define STATUS_RX_PROTO_SHIFT		18
+#define STATUS_FILTER_INDEX_MASK	0xFFFF
+/* Tx status bits */
+#define STATUS_TX_CSUM_START_MASK	0X7FFF
+#define STATUS_TX_CSUM_START_SHIFT	16
+#define STATUS_TX_CSUM_PROTO_UDP	0x8000
+#define STATUS_TX_CSUM_OFFSET_MASK	0x7FFF
+#define STATUS_TX_CSUM_LV		0x80000000
+
+/* DMA Descriptor */
+#define DMA_DESC_LENGTH_STATUS	0x00	/* in bytes of data in buffer */
+#define DMA_DESC_ADDRESS_LO	0x04	/* lower bits of PA */
+#define DMA_DESC_ADDRESS_HI	0x08	/* upper 32 bits of PA, GENETv4+ */
+
+/* Rx/Tx common counter group */
+struct bcmgenet_pkt_counters {
+	u32	cnt_64;		/* RO Received/Transmited 64 bytes packet */
+	u32	cnt_127;	/* RO Rx/Tx 127 bytes packet */
+	u32	cnt_255;	/* RO Rx/Tx 65-255 bytes packet */
+	u32	cnt_511;	/* RO Rx/Tx 256-511 bytes packet */
+	u32	cnt_1023;	/* RO Rx/Tx 512-1023 bytes packet */
+	u32	cnt_1518;	/* RO Rx/Tx 1024-1518 bytes packet */
+	u32	cnt_mgv;	/* RO Rx/Tx 1519-1522 good VLAN packet */
+	u32	cnt_2047;	/* RO Rx/Tx 1522-2047 bytes packet*/
+	u32	cnt_4095;	/* RO Rx/Tx 2048-4095 bytes packet*/
+	u32	cnt_9216;	/* RO Rx/Tx 4096-9216 bytes packet*/
+};
+
+/* RSV, Receive Status Vector */
+struct bcmgenet_rx_counters {
+	struct  bcmgenet_pkt_counters pkt_cnt;
+	u32	pkt;		/* RO (0x428) Received pkt count*/
+	u32	bytes;		/* RO Received byte count */
+	u32	mca;		/* RO # of Received multicast pkt */
+	u32	bca;		/* RO # of Receive broadcast pkt */
+	u32	fcs;		/* RO # of Received FCS error  */
+	u32	cf;		/* RO # of Received control frame pkt*/
+	u32	pf;		/* RO # of Received pause frame pkt */
+	u32	uo;		/* RO # of unknown op code pkt */
+	u32	aln;		/* RO # of alignment error count */
+	u32	flr;		/* RO # of frame length out of range count */
+	u32	cde;		/* RO # of code error pkt */
+	u32	fcr;		/* RO # of carrier sense error pkt */
+	u32	ovr;		/* RO # of oversize pkt*/
+	u32	jbr;		/* RO # of jabber count */
+	u32	mtue;		/* RO # of MTU error pkt*/
+	u32	pok;		/* RO # of Received good pkt */
+	u32	uc;		/* RO # of unicast pkt */
+	u32	ppp;		/* RO # of PPP pkt */
+	u32	rcrc;		/* RO (0x470),# of CRC match pkt */
+};
+
+/* TSV, Transmit Status Vector */
+struct bcmgenet_tx_counters {
+	struct bcmgenet_pkt_counters pkt_cnt;
+	u32	pkts;		/* RO (0x4a8) Transmited pkt */
+	u32	mca;		/* RO # of xmited multicast pkt */
+	u32	bca;		/* RO # of xmited broadcast pkt */
+	u32	pf;		/* RO # of xmited pause frame count */
+	u32	cf;		/* RO # of xmited control frame count */
+	u32	fcs;		/* RO # of xmited FCS error count */
+	u32	ovr;		/* RO # of xmited oversize pkt */
+	u32	drf;		/* RO # of xmited deferral pkt */
+	u32	edf;		/* RO # of xmited Excessive deferral pkt*/
+	u32	scl;		/* RO # of xmited single collision pkt */
+	u32	mcl;		/* RO # of xmited multiple collision pkt*/
+	u32	lcl;		/* RO # of xmited late collision pkt */
+	u32	ecl;		/* RO # of xmited excessive collision pkt*/
+	u32	frg;		/* RO # of xmited fragments pkt*/
+	u32	ncl;		/* RO # of xmited total collision count */
+	u32	jbr;		/* RO # of xmited jabber count*/
+	u32	bytes;		/* RO # of xmited byte count */
+	u32	pok;		/* RO # of xmited good pkt */
+	u32	uc;		/* RO (0x0x4f0)# of xmited unitcast pkt */
+};
+
+struct bcmgenet_mib_counters {
+	struct bcmgenet_rx_counters rx;
+	struct bcmgenet_tx_counters tx;
+	u32	rx_runt_cnt;
+	u32	rx_runt_fcs;
+	u32	rx_runt_fcs_align;
+	u32	rx_runt_bytes;
+	u32	rbuf_ovflow_cnt;
+	u32	rbuf_err_cnt;
+	u32	mdf_err_cnt;
+};
+
+#define UMAC_HD_BKP_CTRL		0x004
+#define	 HD_FC_EN			(1 << 0)
+#define  HD_FC_BKOFF_OK			(1 << 1)
+#define  IPG_CONFIG_RX_SHIFT		2
+#define  IPG_CONFIG_RX_MASK		0x1F
+
+#define UMAC_CMD			0x008
+#define  CMD_TX_EN			(1 << 0)
+#define  CMD_RX_EN			(1 << 1)
+#define  UMAC_SPEED_10			0
+#define  UMAC_SPEED_100			1
+#define  UMAC_SPEED_1000		2
+#define  UMAC_SPEED_2500		3
+#define  CMD_SPEED_SHIFT		2
+#define  CMD_SPEED_MASK			3
+#define  CMD_PROMISC			(1 << 4)
+#define  CMD_PAD_EN			(1 << 5)
+#define  CMD_CRC_FWD			(1 << 6)
+#define  CMD_PAUSE_FWD			(1 << 7)
+#define  CMD_RX_PAUSE_IGNORE		(1 << 8)
+#define  CMD_TX_ADDR_INS		(1 << 9)
+#define  CMD_HD_EN			(1 << 10)
+#define  CMD_SW_RESET			(1 << 13)
+#define  CMD_LCL_LOOP_EN		(1 << 15)
+#define  CMD_AUTO_CONFIG		(1 << 22)
+#define  CMD_CNTL_FRM_EN		(1 << 23)
+#define  CMD_NO_LEN_CHK			(1 << 24)
+#define  CMD_RMT_LOOP_EN		(1 << 25)
+#define  CMD_PRBL_EN			(1 << 27)
+#define  CMD_TX_PAUSE_IGNORE		(1 << 28)
+#define  CMD_TX_RX_EN			(1 << 29)
+#define  CMD_RUNT_FILTER_DIS		(1 << 30)
+
+#define UMAC_MAC0			0x00C
+#define UMAC_MAC1			0x010
+#define UMAC_MAX_FRAME_LEN		0x014
+
+#define UMAC_TX_FLUSH			0x334
+
+#define UMAC_MIB_START			0x400
+
+#define UMAC_MDIO_CMD			0x614
+#define  MDIO_START_BUSY		(1 << 29)
+#define  MDIO_READ_FAIL			(1 << 28)
+#define  MDIO_RD			(2 << 26)
+#define  MDIO_WR			(1 << 26)
+#define  MDIO_PMD_SHIFT			21
+#define  MDIO_PMD_MASK			0x1F
+#define  MDIO_REG_SHIFT			16
+#define  MDIO_REG_MASK			0x1F
+
+#define UMAC_RBUF_OVFL_CNT		0x61C
+
+#define UMAC_MPD_CTRL			0x620
+#define  MPD_EN				(1 << 0)
+#define  MPD_PW_EN			(1 << 27)
+#define  MPD_MSEQ_LEN_SHIFT		16
+#define  MPD_MSEQ_LEN_MASK		0xFF
+
+#define UMAC_MPD_PW_MS			0x624
+#define UMAC_MPD_PW_LS			0x628
+#define UMAC_RBUF_ERR_CNT		0x634
+#define UMAC_MDF_ERR_CNT		0x638
+#define UMAC_MDF_CTRL			0x650
+#define UMAC_MDF_ADDR			0x654
+#define UMAC_MIB_CTRL			0x580
+#define  MIB_RESET_RX			(1 << 0)
+#define  MIB_RESET_RUNT			(1 << 1)
+#define  MIB_RESET_TX			(1 << 2)
+
+#define RBUF_CTRL			0x00
+#define  RBUF_64B_EN			(1 << 0)
+#define  RBUF_ALIGN_2B			(1 << 1)
+#define  RBUF_BAD_DIS			(1 << 2)
+
+#define RBUF_STATUS			0x0C
+#define  RBUF_STATUS_WOL		(1 << 0)
+#define  RBUF_STATUS_MPD_INTR_ACTIVE	(1 << 1)
+#define  RBUF_STATUS_ACPI_INTR_ACTIVE	(1 << 2)
+
+#define RBUF_CHK_CTRL			0x14
+#define  RBUF_RXCHK_EN			(1 << 0)
+#define  RBUF_SKIP_FCS			(1 << 4)
+
+#define RBUF_TBUF_SIZE_CTRL		0xb4
+
+#define RBUF_HFB_CTRL_V1		0x38
+#define  RBUF_HFB_FILTER_EN_SHIFT	16
+#define  RBUF_HFB_FILTER_EN_MASK	0xffff0000
+#define  RBUF_HFB_EN			(1 << 0)
+#define  RBUF_HFB_256B			(1 << 1)
+#define  RBUF_ACPI_EN			(1 << 2)
+
+#define RBUF_HFB_LEN_V1			0x3C
+#define  RBUF_FLTR_LEN_MASK		0xFF
+#define  RBUF_FLTR_LEN_SHIFT		8
+
+#define TBUF_CTRL			0x00
+#define TBUF_BP_MC			0x0C
+
+#define TBUF_CTRL_V1			0x80
+#define TBUF_BP_MC_V1			0xA0
+
+#define HFB_CTRL			0x00
+#define HFB_FLT_ENABLE_V3PLUS		0x04
+#define HFB_FLT_LEN_V2			0x04
+#define HFB_FLT_LEN_V3PLUS		0x1C
+
+/* uniMac intrl2 registers */
+#define INTRL2_CPU_STAT			0x00
+#define INTRL2_CPU_SET			0x04
+#define INTRL2_CPU_CLEAR		0x08
+#define INTRL2_CPU_MASK_STATUS		0x0C
+#define INTRL2_CPU_MASK_SET		0x10
+#define INTRL2_CPU_MASK_CLEAR		0x14
+
+/* INTRL2 instance 0 definitions */
+#define UMAC_IRQ_SCB			(1 << 0)
+#define UMAC_IRQ_EPHY			(1 << 1)
+#define UMAC_IRQ_PHY_DET_R		(1 << 2)
+#define UMAC_IRQ_PHY_DET_F		(1 << 3)
+#define UMAC_IRQ_LINK_UP		(1 << 4)
+#define UMAC_IRQ_LINK_DOWN		(1 << 5)
+#define UMAC_IRQ_UMAC			(1 << 6)
+#define UMAC_IRQ_UMAC_TSV		(1 << 7)
+#define UMAC_IRQ_TBUF_UNDERRUN		(1 << 8)
+#define UMAC_IRQ_RBUF_OVERFLOW		(1 << 9)
+#define UMAC_IRQ_HFB_SM			(1 << 10)
+#define UMAC_IRQ_HFB_MM			(1 << 11)
+#define UMAC_IRQ_MPD_R			(1 << 12)
+#define UMAC_IRQ_RXDMA_MBDONE		(1 << 13)
+#define UMAC_IRQ_RXDMA_PDONE		(1 << 14)
+#define UMAC_IRQ_RXDMA_BDONE		(1 << 15)
+#define UMAC_IRQ_TXDMA_MBDONE		(1 << 16)
+#define UMAC_IRQ_TXDMA_PDONE		(1 << 17)
+#define UMAC_IRQ_TXDMA_BDONE		(1 << 18)
+/* Only valid for GENETv3+ */
+#define UMAC_IRQ_MDIO_DONE		(1 << 23)
+#define UMAC_IRQ_MDIO_ERROR		(1 << 24)
+
+/* Register block offsets */
+#define GENET_SYS_OFF			0x0000
+#define GENET_GR_BRIDGE_OFF		0x0040
+#define GENET_EXT_OFF			0x0080
+#define GENET_INTRL2_0_OFF		0x0200
+#define GENET_INTRL2_1_OFF		0x0240
+#define GENET_RBUF_OFF			0x0300
+#define GENET_UMAC_OFF			0x0800
+
+/* SYS block offsets and register definitions */
+#define SYS_REV_CTRL			0x00
+#define SYS_PORT_CTRL			0x04
+#define  PORT_MODE_INT_EPHY		0
+#define  PORT_MODE_INT_GPHY		1
+#define  PORT_MODE_EXT_EPHY		2
+#define  PORT_MODE_EXT_GPHY		3
+#define  PORT_MODE_EXT_RVMII_25		(4 | BIT(4))
+#define  PORT_MODE_EXT_RVMII_50		4
+#define  LED_ACT_SOURCE_MAC		(1 << 9)
+
+#define SYS_RBUF_FLUSH_CTRL		0x08
+#define SYS_TBUF_FLUSH_CTRL		0x0C
+#define RBUF_FLUSH_CTRL_V1		0x04
+
+/* Ext block register offsets and definitions */
+#define EXT_EXT_PWR_MGMT		0x00
+#define  EXT_PWR_DOWN_BIAS		(1 << 0)
+#define  EXT_PWR_DOWN_DLL		(1 << 1)
+#define  EXT_PWR_DOWN_PHY		(1 << 2)
+#define  EXT_PWR_DN_EN_LD		(1 << 3)
+#define  EXT_ENERGY_DET			(1 << 4)
+#define  EXT_IDDQ_FROM_PHY		(1 << 5)
+#define  EXT_PHY_RESET			(1 << 8)
+#define  EXT_ENERGY_DET_MASK		(1 << 12)
+
+#define EXT_RGMII_OOB_CTRL		0x0C
+#define  RGMII_MODE_EN			(1 << 0)
+#define  RGMII_LINK			(1 << 4)
+#define  OOB_DISABLE			(1 << 5)
+#define  ID_MODE_DIS			(1 << 16)
+
+#define EXT_GPHY_CTRL			0x1C
+#define  EXT_CFG_IDDQ_BIAS		(1 << 0)
+#define  EXT_CFG_PWR_DOWN		(1 << 1)
+#define  EXT_GPHY_RESET			(1 << 5)
+
+/* DMA rings size */
+#define DMA_RING_SIZE			(0x40)
+#define DMA_RINGS_SIZE			(DMA_RING_SIZE * (DESC_INDEX + 1))
+
+/* DMA registers common definitions */
+#define DMA_RW_POINTER_MASK		0x1FF
+#define DMA_P_INDEX_DISCARD_CNT_MASK	0xFFFF
+#define DMA_P_INDEX_DISCARD_CNT_SHIFT	16
+#define DMA_BUFFER_DONE_CNT_MASK	0xFFFF
+#define DMA_BUFFER_DONE_CNT_SHIFT	16
+#define DMA_P_INDEX_MASK		0xFFFF
+#define DMA_C_INDEX_MASK		0xFFFF
+
+/* DMA ring size register */
+#define DMA_RING_SIZE_MASK		0xFFFF
+#define DMA_RING_SIZE_SHIFT		16
+#define DMA_RING_BUFFER_SIZE_MASK	0xFFFF
+
+/* DMA interrupt threshold register */
+#define DMA_INTR_THRESHOLD_MASK		0x00FF
+
+/* DMA XON/XOFF register */
+#define DMA_XON_THREHOLD_MASK		0xFFFF
+#define DMA_XOFF_THRESHOLD_MASK		0xFFFF
+#define DMA_XOFF_THRESHOLD_SHIFT	16
+
+/* DMA flow period register */
+#define DMA_FLOW_PERIOD_MASK		0xFFFF
+#define DMA_MAX_PKT_SIZE_MASK		0xFFFF
+#define DMA_MAX_PKT_SIZE_SHIFT		16
+
+
+/* DMA control register */
+#define DMA_EN				(1 << 0)
+#define DMA_RING_BUF_EN_SHIFT		0x01
+#define DMA_RING_BUF_EN_MASK		0xFFFF
+#define DMA_TSB_SWAP_EN			(1 << 20)
+
+/* DMA status register */
+#define DMA_DISABLED			(1 << 0)
+#define DMA_DESC_RAM_INIT_BUSY		(1 << 1)
+
+/* DMA SCB burst size register */
+#define DMA_SCB_BURST_SIZE_MASK		0x1F
+
+/* DMA activity vector register */
+#define DMA_ACTIVITY_VECTOR_MASK	0x1FFFF
+
+/* DMA backpressure mask register */
+#define DMA_BACKPRESSURE_MASK		0x1FFFF
+#define DMA_PFC_ENABLE			(1 << 31)
+
+/* DMA backpressure status register */
+#define DMA_BACKPRESSURE_STATUS_MASK	0x1FFFF
+
+/* DMA override register */
+#define DMA_LITTLE_ENDIAN_MODE		(1 << 0)
+#define DMA_REGISTER_MODE		(1 << 1)
+
+/* DMA timeout register */
+#define DMA_TIMEOUT_MASK		0xFFFF
+#define DMA_TIMEOUT_VAL			5000	/* micro seconds */
+
+/* TDMA rate limiting control register */
+#define DMA_RATE_LIMIT_EN_MASK		0xFFFF
+
+/* TDMA arbitration control register */
+#define DMA_ARBITER_MODE_MASK		0x03
+#define DMA_RING_BUF_PRIORITY_MASK	0x1F
+#define DMA_RING_BUF_PRIORITY_SHIFT	5
+#define DMA_RATE_ADJ_MASK		0xFF
+
+/* Tx/Rx Dma Descriptor common bits*/
+#define DMA_BUFLENGTH_MASK		0x0fff
+#define DMA_BUFLENGTH_SHIFT		16
+#define DMA_OWN				0x8000
+#define DMA_EOP				0x4000
+#define DMA_SOP				0x2000
+#define DMA_WRAP			0x1000
+/* Tx specific Dma descriptor bits */
+#define DMA_TX_UNDERRUN			0x0200
+#define DMA_TX_APPEND_CRC		0x0040
+#define DMA_TX_OW_CRC			0x0020
+#define DMA_TX_DO_CSUM			0x0010
+#define DMA_TX_QTAG_SHIFT		7
+
+/* Rx Specific Dma descriptor bits */
+#define DMA_RX_CHK_V3PLUS		0x8000
+#define DMA_RX_CHK_V12			0x1000
+#define DMA_RX_BRDCAST			0x0040
+#define DMA_RX_MULT			0x0020
+#define DMA_RX_LG			0x0010
+#define DMA_RX_NO			0x0008
+#define DMA_RX_RXER			0x0004
+#define DMA_RX_CRC_ERROR		0x0002
+#define DMA_RX_OV			0x0001
+#define DMA_RX_FI_MASK			0x001F
+#define DMA_RX_FI_SHIFT			0x0007
+#define DMA_DESC_ALLOC_MASK		0x00FF
+
+#define DMA_ARBITER_RR			0x00
+#define DMA_ARBITER_WRR			0x01
+#define DMA_ARBITER_SP			0x02
+
+struct enet_cb {
+	struct sk_buff      *skb;
+	void __iomem *bd_addr;
+	DEFINE_DMA_UNMAP_ADDR(dma_addr);
+	DEFINE_DMA_UNMAP_LEN(dma_len);
+};
+
+/* power management mode */
+enum bcmgenet_power_mode {
+	GENET_POWER_CABLE_SENSE = 0,
+	GENET_POWER_PASSIVE,
+};
+
+struct bcmgenet_priv;
+
+/* We support both runtime GENET detection and compile-time
+ * to optimize code-paths for a given hardware
+ */
+enum bcmgenet_version {
+	GENET_V1 = 1,
+	GENET_V2,
+	GENET_V3,
+	GENET_V4
+};
+
+#define GENET_IS_V1(p)	((p)->version == GENET_V1)
+#define GENET_IS_V2(p)	((p)->version == GENET_V2)
+#define GENET_IS_V3(p)	((p)->version == GENET_V3)
+#define GENET_IS_V4(p)	((p)->version == GENET_V4)
+
+/* Hardware flags */
+#define GENET_HAS_40BITS	(1 << 0)
+#define GENET_HAS_EXT		(1 << 1)
+#define GENET_HAS_MDIO_INTR	(1 << 2)
+
+/* BCMGENET hardware parameters, keep this structure nicely aligned
+ * since it is going to be used in hot paths
+ */
+struct bcmgenet_hw_params {
+	u8		tx_queues;
+	u8		rx_queues;
+	u8		bds_cnt;
+	u8		bp_in_en_shift;
+	u32		bp_in_mask;
+	u8		hfb_filter_cnt;
+	u8		qtag_mask;
+	u16		tbuf_offset;
+	u32		hfb_offset;
+	u32		hfb_reg_offset;
+	u32		rdma_offset;
+	u32		tdma_offset;
+	u32		words_per_bd;
+	u32		flags;
+};
+
+struct bcmgenet_tx_ring {
+	spinlock_t	lock;		/* ring lock */
+	unsigned int	index;		/* ring index */
+	unsigned int	queue;		/* queue index */
+	struct enet_cb	*cbs;		/* tx ring buffer control block*/
+	unsigned int	size;		/* size of each tx ring */
+	unsigned int	c_index;	/* last consumer index of each ring*/
+	unsigned int	free_bds;	/* # of free bds for each ring */
+	unsigned int	write_ptr;	/* Tx ring write pointer SW copy */
+	unsigned int	prod_index;	/* Tx ring producer index SW copy */
+	unsigned int	cb_ptr;		/* Tx ring initial CB ptr */
+	unsigned int	end_ptr;	/* Tx ring end CB ptr */
+	void (*int_enable)(struct bcmgenet_priv *priv,
+				struct bcmgenet_tx_ring *);
+	void (*int_disable)(struct bcmgenet_priv *priv,
+				struct bcmgenet_tx_ring *);
+};
+
+/* device context */
+struct bcmgenet_priv {
+	void __iomem *base;
+	enum bcmgenet_version version;
+	struct net_device *dev;
+	spinlock_t lock;
+	spinlock_t bh_lock;
+	u32 int0_mask;
+	u32 int1_mask;
+
+	/* NAPI for descriptor based rx */
+	struct napi_struct napi ____cacheline_aligned;
+
+	/* transmit variables */
+	void __iomem *tx_bds;
+	struct enet_cb *tx_cbs;
+	unsigned int num_tx_bds;
+
+	struct bcmgenet_tx_ring tx_rings[DESC_INDEX + 1];
+
+	/* receive variables */
+	void __iomem *rx_bds;
+	void __iomem *rx_bd_assign_ptr;
+	int rx_bd_assign_index;
+	struct enet_cb *rx_cbs;
+	unsigned int num_rx_bds;
+	unsigned int rx_buf_len;
+	unsigned int rx_read_ptr;
+	unsigned int rx_c_index;
+
+	/* other misc variables */
+	struct bcmgenet_hw_params *hw_params;
+
+	/* MDIO bus variables */
+	wait_queue_head_t wq;
+	struct phy_device *phydev;
+	struct device_node *phy_dn;
+	struct mii_bus *mii_bus;
+
+	/* PHY device variables */
+	int old_duplex;
+	int old_link;
+	int old_pause;
+	phy_interface_t phy_interface;
+	int phy_addr;
+	int ext_phy;
+
+	/* Interrupt variables */
+	struct work_struct bcmgenet_irq_work;
+	int irq0;
+	int irq1;
+	unsigned int irq0_stat;
+	unsigned int irq1_stat;
+
+	/* HW descriptors/checksum variables */
+	bool desc_64b_en;
+	bool desc_rxchk_en;
+	bool crc_fwd_en;
+
+	unsigned int dma_rx_chk_bit;
+
+	u32 msg_enable;
+
+	struct clk *clk;
+	struct platform_device *pdev;
+
+	/* WOL */
+	unsigned long wol_enabled;
+	struct clk *clk_wol;
+	u32 wolopts;
+
+	struct bcmgenet_mib_counters mib;
+};
+
+#define GENET_IO_MACRO(name, offset)					\
+static inline u32 bcmgenet_##name##_readl(struct bcmgenet_priv *priv,	\
+					u32 off)			\
+{									\
+	return __raw_readl(priv->base + offset + off);			\
+}									\
+static inline void bcmgenet_##name##_writel(struct bcmgenet_priv *priv,	\
+					u32 val, u32 off)		\
+{									\
+	__raw_writel(val, priv->base + offset + off);			\
+}
+
+GENET_IO_MACRO(ext, GENET_EXT_OFF);
+GENET_IO_MACRO(umac, GENET_UMAC_OFF);
+GENET_IO_MACRO(sys, GENET_SYS_OFF);
+
+/* interrupt l2 registers accessors */
+GENET_IO_MACRO(intrl2_0, GENET_INTRL2_0_OFF);
+GENET_IO_MACRO(intrl2_1, GENET_INTRL2_1_OFF);
+
+/* HFB register accessors  */
+GENET_IO_MACRO(hfb, priv->hw_params->hfb_offset);
+
+/* GENET v2+ HFB control and filter len helpers */
+GENET_IO_MACRO(hfb_reg, priv->hw_params->hfb_reg_offset);
+
+/* RBUF register accessors */
+GENET_IO_MACRO(rbuf, GENET_RBUF_OFF);
+
+/* MDIO routines */
+int bcmgenet_mii_init(struct net_device *dev);
+int bcmgenet_mii_config(struct net_device *dev);
+void bcmgenet_mii_exit(struct net_device *dev);
+void bcmgenet_mii_reset(struct net_device *dev);
+
+#endif /* __BCMGENET_H__ */
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@ -0,0 +1,464 @@
+/*
+ * Broadcom GENET MDIO routines
+ *
+ * Copyright (c) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/wait.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/bitops.h>
+#include <linux/netdevice.h>
+#include <linux/platform_device.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+#include <linux/brcmphy.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+
+#include "bcmgenet.h"
+
+/* read a value from the MII */
+static int bcmgenet_mii_read(struct mii_bus *bus, int phy_id, int location)
+{
+	int ret;
+	struct net_device *dev = bus->priv;
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	u32 reg;
+
+	bcmgenet_umac_writel(priv, (MDIO_RD | (phy_id << MDIO_PMD_SHIFT) |
+			(location << MDIO_REG_SHIFT)), UMAC_MDIO_CMD);
+	/* Start MDIO transaction*/
+	reg = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
+	reg |= MDIO_START_BUSY;
+	bcmgenet_umac_writel(priv, reg, UMAC_MDIO_CMD);
+	wait_event_timeout(priv->wq,
+			!(bcmgenet_umac_readl(priv, UMAC_MDIO_CMD)
+				& MDIO_START_BUSY),
+			HZ / 100);
+	ret = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
+
+	if (ret & MDIO_READ_FAIL)
+		return -EIO;
+
+	return ret & 0xffff;
+}
+
+/* write a value to the MII */
+static int bcmgenet_mii_write(struct mii_bus *bus, int phy_id,
+			int location, u16 val)
+{
+	struct net_device *dev = bus->priv;
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	u32 reg;
+
+	bcmgenet_umac_writel(priv, (MDIO_WR | (phy_id << MDIO_PMD_SHIFT) |
+			(location << MDIO_REG_SHIFT) | (0xffff & val)),
+			UMAC_MDIO_CMD);
+	reg = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
+	reg |= MDIO_START_BUSY;
+	bcmgenet_umac_writel(priv, reg, UMAC_MDIO_CMD);
+	wait_event_timeout(priv->wq,
+			!(bcmgenet_umac_readl(priv, UMAC_MDIO_CMD) &
+				MDIO_START_BUSY),
+			HZ / 100);
+
+	return 0;
+}
+
+/* setup netdev link state when PHY link status change and
+ * update UMAC and RGMII block when link up
+ */
+static void bcmgenet_mii_setup(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	struct phy_device *phydev = priv->phydev;
+	u32 reg, cmd_bits = 0;
+	unsigned int status_changed = 0;
+
+	if (priv->old_link != phydev->link) {
+		status_changed = 1;
+		priv->old_link = phydev->link;
+	}
+
+	if (phydev->link) {
+		/* program UMAC and RGMII block based on established link
+		 * speed, pause, and duplex.
+		 * the speed set in umac->cmd tell RGMII block which clock
+		 * 25MHz(100Mbps)/125MHz(1Gbps) to use for transmit.
+		 * receive clock is provided by PHY.
+		 */
+		reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
+		reg &= ~OOB_DISABLE;
+		reg |= RGMII_LINK;
+		bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+
+		/* speed */
+		if (phydev->speed == SPEED_1000)
+			cmd_bits = UMAC_SPEED_1000;
+		else if (phydev->speed == SPEED_100)
+			cmd_bits = UMAC_SPEED_100;
+		else
+			cmd_bits = UMAC_SPEED_10;
+		cmd_bits <<= CMD_SPEED_SHIFT;
+
+		if (priv->old_duplex != phydev->duplex) {
+			status_changed = 1;
+			priv->old_duplex = phydev->duplex;
+		}
+
+		/* duplex */
+		if (phydev->duplex != DUPLEX_FULL)
+			cmd_bits |= CMD_HD_EN;
+
+		if (priv->old_pause != phydev->pause) {
+			status_changed = 1;
+			priv->old_pause = phydev->pause;
+		}
+
+		/* pause capability */
+		if (!phydev->pause)
+			cmd_bits |= CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE;
+
+		reg = bcmgenet_umac_readl(priv, UMAC_CMD);
+		reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) |
+			       CMD_HD_EN |
+			       CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE);
+		reg |= cmd_bits;
+		bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	}
+
+	if (status_changed)
+		phy_print_status(phydev);
+}
+
+void bcmgenet_mii_reset(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+
+	if (priv->phydev) {
+		phy_init_hw(priv->phydev);
+		phy_start_aneg(priv->phydev);
+	}
+}
+
+static void bcmgenet_ephy_power_up(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	u32 reg = 0;
+
+	/* EXT_GPHY_CTRL is only valid for GENETv4 and onward */
+	if (!GENET_IS_V4(priv))
+		return;
+
+	reg = bcmgenet_ext_readl(priv, EXT_GPHY_CTRL);
+	reg &= ~(EXT_CFG_IDDQ_BIAS | EXT_CFG_PWR_DOWN);
+	reg |= EXT_GPHY_RESET;
+	bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
+	mdelay(2);
+
+	reg &= ~EXT_GPHY_RESET;
+	bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
+	udelay(20);
+}
+
+static void bcmgenet_internal_phy_setup(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	u32 reg;
+
+	/* Power up EPHY */
+	bcmgenet_ephy_power_up(dev);
+	/* enable APD */
+	reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
+	reg |= EXT_PWR_DN_EN_LD;
+	bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
+	bcmgenet_mii_reset(dev);
+}
+
+static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
+{
+	u32 reg;
+
+	/* Speed settings are set in bcmgenet_mii_setup() */
+	reg = bcmgenet_sys_readl(priv, SYS_PORT_CTRL);
+	reg |= LED_ACT_SOURCE_MAC;
+	bcmgenet_sys_writel(priv, reg, SYS_PORT_CTRL);
+}
+
+int bcmgenet_mii_config(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	struct phy_device *phydev = priv->phydev;
+	struct device *kdev = &priv->pdev->dev;
+	const char *phy_name = NULL;
+	u32 id_mode_dis = 0;
+	u32 port_ctrl;
+	u32 reg;
+
+	priv->ext_phy = !phy_is_internal(priv->phydev) &&
+			(priv->phy_interface != PHY_INTERFACE_MODE_MOCA);
+
+	if (phy_is_internal(priv->phydev))
+		priv->phy_interface = PHY_INTERFACE_MODE_NA;
+
+	switch (priv->phy_interface) {
+	case PHY_INTERFACE_MODE_NA:
+	case PHY_INTERFACE_MODE_MOCA:
+		/* Irrespective of the actually configured PHY speed (100 or
+		 * 1000) GENETv4 only has an internal GPHY so we will just end
+		 * up masking the Gigabit features from what we support, not
+		 * switching to the EPHY
+		 */
+		if (GENET_IS_V4(priv))
+			port_ctrl = PORT_MODE_INT_GPHY;
+		else
+			port_ctrl = PORT_MODE_INT_EPHY;
+
+		bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
+
+		if (phy_is_internal(priv->phydev)) {
+			phy_name = "internal PHY";
+			bcmgenet_internal_phy_setup(dev);
+		} else if (priv->phy_interface == PHY_INTERFACE_MODE_MOCA) {
+			phy_name = "MoCA";
+			bcmgenet_moca_phy_setup(priv);
+		}
+		break;
+
+	case PHY_INTERFACE_MODE_MII:
+		phy_name = "external MII";
+		phydev->supported &= PHY_BASIC_FEATURES;
+		bcmgenet_sys_writel(priv,
+				PORT_MODE_EXT_EPHY, SYS_PORT_CTRL);
+		break;
+
+	case PHY_INTERFACE_MODE_REVMII:
+		phy_name = "external RvMII";
+		/* of_mdiobus_register took care of reading the 'max-speed'
+		 * PHY property for us, effectively limiting the PHY supported
+		 * capabilities, use that knowledge to also configure the
+		 * Reverse MII interface correctly.
+		 */
+		if ((priv->phydev->supported & PHY_BASIC_FEATURES) ==
+				PHY_BASIC_FEATURES)
+			port_ctrl = PORT_MODE_EXT_RVMII_25;
+		else
+			port_ctrl = PORT_MODE_EXT_RVMII_50;
+		bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
+		break;
+
+	case PHY_INTERFACE_MODE_RGMII:
+		/* RGMII_NO_ID: TXC transitions at the same time as TXD
+		 *		(requires PCB or receiver-side delay)
+		 * RGMII:	Add 2ns delay on TXC (90 degree shift)
+		 *
+		 * ID is implicitly disabled for 100Mbps (RG)MII operation.
+		 */
+		id_mode_dis = BIT(16);
+		/* fall through */
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (id_mode_dis)
+			phy_name = "external RGMII (no delay)";
+		else
+			phy_name = "external RGMII (TX delay)";
+		reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
+		reg |= RGMII_MODE_EN | id_mode_dis;
+		bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+		bcmgenet_sys_writel(priv,
+				PORT_MODE_EXT_GPHY, SYS_PORT_CTRL);
+		break;
+	default:
+		dev_err(kdev, "unknown phy mode: %d\n", priv->phy_interface);
+		return -EINVAL;
+	}
+
+	dev_info(kdev, "configuring instance for %s\n", phy_name);
+
+	return 0;
+}
+
+static int bcmgenet_mii_probe(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	struct phy_device *phydev;
+	unsigned int phy_flags;
+	int ret;
+
+	if (priv->phydev) {
+		pr_info("PHY already attached\n");
+		return 0;
+	}
+
+	if (priv->phy_dn)
+		phydev = of_phy_connect(dev, priv->phy_dn,
+					bcmgenet_mii_setup, 0,
+					priv->phy_interface);
+	else
+		phydev = of_phy_connect_fixed_link(dev,
+					bcmgenet_mii_setup,
+					priv->phy_interface);
+
+	if (!phydev) {
+		pr_err("could not attach to PHY\n");
+		return -ENODEV;
+	}
+
+	priv->old_link = -1;
+	priv->old_duplex = -1;
+	priv->old_pause = -1;
+	priv->phydev = phydev;
+
+	/* Configure port multiplexer based on what the probed PHY device since
+	 * reading the 'max-speed' property determines the maximum supported
+	 * PHY speed which is needed for bcmgenet_mii_config() to configure
+	 * things appropriately.
+	 */
+	ret = bcmgenet_mii_config(dev);
+	if (ret) {
+		phy_disconnect(priv->phydev);
+		return ret;
+	}
+
+	phy_flags = PHY_BRCM_100MBPS_WAR;
+
+	/* workarounds are only needed for 100Mpbs PHYs, and
+	 * never on GENET V1 hardware
+	 */
+	if ((phydev->supported & PHY_GBIT_FEATURES) || GENET_IS_V1(priv))
+		phy_flags = 0;
+
+	phydev->dev_flags |= phy_flags;
+	phydev->advertising = phydev->supported;
+
+	/* The internal PHY has its link interrupts routed to the
+	 * Ethernet MAC ISRs
+	 */
+	if (phy_is_internal(priv->phydev))
+		priv->mii_bus->irq[phydev->addr] = PHY_IGNORE_INTERRUPT;
+	else
+		priv->mii_bus->irq[phydev->addr] = PHY_POLL;
+
+	pr_info("attached PHY at address %d [%s]\n",
+			phydev->addr, phydev->drv->name);
+
+	return 0;
+}
+
+static int bcmgenet_mii_alloc(struct bcmgenet_priv *priv)
+{
+	struct mii_bus *bus;
+
+	if (priv->mii_bus)
+		return 0;
+
+	priv->mii_bus = mdiobus_alloc();
+	if (!priv->mii_bus) {
+		pr_err("failed to allocate\n");
+		return -ENOMEM;
+	}
+
+	bus = priv->mii_bus;
+	bus->priv = priv->dev;
+	bus->name = "bcmgenet MII bus";
+	bus->parent = &priv->pdev->dev;
+	bus->read = bcmgenet_mii_read;
+	bus->write = bcmgenet_mii_write;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%d",
+			priv->pdev->name, priv->pdev->id);
+
+	bus->irq = kzalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+	if (!bus->irq) {
+		mdiobus_free(priv->mii_bus);
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static int bcmgenet_mii_of_init(struct bcmgenet_priv *priv)
+{
+	struct device_node *dn = priv->pdev->dev.of_node;
+	struct device *kdev = &priv->pdev->dev;
+	struct device_node *mdio_dn;
+	char *compat;
+	int ret;
+
+	compat = kasprintf(GFP_KERNEL, "brcm,genet-mdio-v%d", priv->version);
+	if (!compat)
+		return -ENOMEM;
+
+	mdio_dn = of_find_compatible_node(dn, NULL, compat);
+	kfree(compat);
+	if (!mdio_dn) {
+		dev_err(kdev, "unable to find MDIO bus node\n");
+		return -ENODEV;
+	}
+
+	ret = of_mdiobus_register(priv->mii_bus, mdio_dn);
+	if (ret) {
+		dev_err(kdev, "failed to register MDIO bus\n");
+		return ret;
+	}
+
+	/* Fetch the PHY phandle */
+	priv->phy_dn = of_parse_phandle(dn, "phy-handle", 0);
+
+	/* Get the link mode */
+	priv->phy_interface = of_get_phy_mode(dn);
+
+	return 0;
+}
+
+int bcmgenet_mii_init(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+	int ret;
+
+	ret = bcmgenet_mii_alloc(priv);
+	if (ret)
+		return ret;
+
+	ret = bcmgenet_mii_of_init(priv);
+	if (ret)
+		goto out_free;
+
+	ret = bcmgenet_mii_probe(dev);
+	if (ret)
+		goto out;
+
+	return 0;
+
+out:
+	mdiobus_unregister(priv->mii_bus);
+out_free:
+	kfree(priv->mii_bus->irq);
+	mdiobus_free(priv->mii_bus);
+	return ret;
+}
+
+void bcmgenet_mii_exit(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+
+	mdiobus_unregister(priv->mii_bus);
+	kfree(priv->mii_bus->irq);
+	mdiobus_free(priv->mii_bus);
+}
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@ -71,6 +71,12 @@ config BCM63XX_PHY
 	---help---
 	  Currently supports the 6348 and 6358 PHYs.

+config BCM7XXX_PHY
+	tristate "Drivers for Broadcom 7xxx SOCs internal PHYs"
+	---help---
+	  Currently supports the BCM7366, BCM7439, BCM7445, and
+	  40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
+
 config BCM87XX_PHY
 	tristate "Driver for Broadcom BCM8706 and BCM8727 PHYs"
 	help
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@ -12,6 +12,7 @@ obj-$(CONFIG_SMSC_PHY)		+= smsc.o
 obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
 obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
 obj-$(CONFIG_BCM63XX_PHY)	+= bcm63xx.o
+obj-$(CONFIG_BCM7XXX_PHY)	+= bcm7xxx.o
 obj-$(CONFIG_BCM87XX_PHY)	+= bcm87xx.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
--- a/drivers/net/phy/bcm7xxx.c
+++ b/drivers/net/phy/bcm7xxx.c
@ -0,0 +1,343 @@
+/*
+ * Broadcom BCM7xxx internal transceivers support.
+ *
+ * Copyright (C) 2014, Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/brcmphy.h>
+
+/* Broadcom BCM7xxx internal PHY registers */
+#define MII_BCM7XXX_CHANNEL_WIDTH	0x2000
+
+/* 40nm only register definitions */
+#define MII_BCM7XXX_100TX_AUX_CTL	0x10
+#define MII_BCM7XXX_100TX_FALSE_CAR	0x13
+#define MII_BCM7XXX_100TX_DISC		0x14
+#define MII_BCM7XXX_AUX_MODE		0x1d
+#define  MII_BCM7XX_64CLK_MDIO		BIT(12)
+#define MII_BCM7XXX_CORE_BASE1E		0x1e
+#define MII_BCM7XXX_TEST		0x1f
+#define  MII_BCM7XXX_SHD_MODE_2		BIT(2)
+
+static int bcm7445_config_init(struct phy_device *phydev)
+{
+	int ret;
+	const struct bcm7445_regs {
+		int reg;
+		u16 value;
+	} bcm7445_regs_cfg[] = {
+		/* increases ADC latency by 24ns */
+		{ MII_BCM54XX_EXP_SEL, 0x0038 },
+		{ MII_BCM54XX_EXP_DATA, 0xAB95 },
+		/* increases internal 1V LDO voltage by 5% */
+		{ MII_BCM54XX_EXP_SEL, 0x2038 },
+		{ MII_BCM54XX_EXP_DATA, 0xBB22 },
+		/* reduce RX low pass filter corner frequency */
+		{ MII_BCM54XX_EXP_SEL, 0x6038 },
+		{ MII_BCM54XX_EXP_DATA, 0xFFC5 },
+		/* reduce RX high pass filter corner frequency */
+		{ MII_BCM54XX_EXP_SEL, 0x003a },
+		{ MII_BCM54XX_EXP_DATA, 0x2002 },
+	};
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(bcm7445_regs_cfg); i++) {
+		ret = phy_write(phydev,
+				bcm7445_regs_cfg[i].reg,
+				bcm7445_regs_cfg[i].value);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static void phy_write_exp(struct phy_device *phydev,
+					u16 reg, u16 value)
+{
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER | reg);
+	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
+}
+
+static void phy_write_misc(struct phy_device *phydev,
+					u16 reg, u16 chl, u16 value)
+{
+	int tmp;
+
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
+
+	tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
+	tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);
+
+	tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) | reg;
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp);
+
+	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
+}
+
+static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev)
+{
+	/* write AFE_RXCONFIG_0 */
+	phy_write_misc(phydev, 0x38, 0x0000, 0xeb19);
+
+	/* write AFE_RXCONFIG_1 */
+	phy_write_misc(phydev, 0x38, 0x0001, 0x9a3f);
+
+	/* write AFE_RX_LP_COUNTER */
+	phy_write_misc(phydev, 0x38, 0x0003, 0x7fc7);
+
+	/* write AFE_HPF_TRIM_OTHERS */
+	phy_write_misc(phydev, 0x3A, 0x0000, 0x000b);
+
+	/* write AFTE_TX_CONFIG */
+	phy_write_misc(phydev, 0x39, 0x0000, 0x0800);
+
+	/* Increase VCO range to prevent unlocking problem of PLL at low
+	 * temp
+	 */
+	phy_write_misc(phydev, 0x0032, 0x0001, 0x0048);
+
+	/* Change Ki to 011 */
+	phy_write_misc(phydev, 0x0032, 0x0002, 0x021b);
+
+	/* Disable loading of TVCO buffer to bandgap, set bandgap trim
+	 * to 111
+	 */
+	phy_write_misc(phydev, 0x0033, 0x0000, 0x0e20);
+
+	/* Adjust bias current trim by -3 */
+	phy_write_misc(phydev, 0x000a, 0x0000, 0x690b);
+
+	/* Switch to CORE_BASE1E */
+	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd);
+
+	/* Reset R_CAL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0010);
+
+	/* Disable Reset R_CAL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0000);
+
+	return 0;
+}
+
+static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = bcm7445_config_init(phydev);
+	if (ret)
+		return ret;
+
+	return bcm7xxx_28nm_afe_config_init(phydev);
+}
+
+static int phy_set_clr_bits(struct phy_device *dev, int location,
+					int set_mask, int clr_mask)
+{
+	int v, ret;
+
+	v = phy_read(dev, location);
+	if (v < 0)
+		return v;
+
+	v &= ~clr_mask;
+	v |= set_mask;
+
+	ret = phy_write(dev, location, v);
+	if (ret < 0)
+		return ret;
+
+	return v;
+}
+
+static int bcm7xxx_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Enable 64 clock MDIO */
+	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XX_64CLK_MDIO);
+	phy_read(phydev, MII_BCM7XXX_AUX_MODE);
+
+	/* Workaround only required for 100Mbits/sec */
+	if (!(phydev->dev_flags & PHY_BRCM_100MBPS_WAR))
+		return 0;
+
+	/* set shadow mode 2 */
+	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
+			MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
+	if (ret < 0)
+		return ret;
+
+	/* set iddq_clkbias */
+	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
+	udelay(10);
+
+	/* reset iddq_clkbias */
+	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);
+
+	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);
+
+	/* reset shadow mode 2 */
+	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, MII_BCM7XXX_SHD_MODE_2, 0);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+/* Workaround for putting the PHY in IDDQ mode, required
+ * for all BCM7XXX PHYs
+ */
+static int bcm7xxx_suspend(struct phy_device *phydev)
+{
+	int ret;
+	const struct bcm7xxx_regs {
+		int reg;
+		u16 value;
+	} bcm7xxx_suspend_cfg[] = {
+		{ MII_BCM7XXX_TEST, 0x008b },
+		{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
+		{ MII_BCM7XXX_100TX_DISC, 0x7000 },
+		{ MII_BCM7XXX_TEST, 0x000f },
+		{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
+		{ MII_BCM7XXX_TEST, 0x000b },
+	};
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
+		ret = phy_write(phydev,
+				bcm7xxx_suspend_cfg[i].reg,
+				bcm7xxx_suspend_cfg[i].value);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int bcm7xxx_dummy_config_init(struct phy_device *phydev)
+{
+	return 0;
+}
+
+static struct phy_driver bcm7xxx_driver[] = {
+{
+	.phy_id		= PHY_ID_BCM7366,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7366",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_afe_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_afe_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_ID_BCM7439,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7439",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_afe_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_afe_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_ID_BCM7445,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7445",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.name		= "Broadcom BCM7XXX 28nm",
+	.phy_id		= PHY_ID_BCM7XXX_28,
+	.phy_id_mask	= PHY_BCM_OUI_MASK,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_BCM_OUI_4,
+	.phy_id_mask	= 0xffff0000,
+	.name		= "Broadcom BCM7XXX 40nm",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_BCM_OUI_5,
+	.phy_id_mask	= 0xffffff00,
+	.name		= "Broadcom BCM7XXX 65nm",
+	.features	= PHY_BASIC_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_dummy_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_config_init,
+	.driver		= { .owner = THIS_MODULE },
+} };
+
+static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
+	{ PHY_ID_BCM7366, 0xfffffff0, },
+	{ PHY_ID_BCM7439, 0xfffffff0, },
+	{ PHY_ID_BCM7445, 0xfffffff0, },
+	{ PHY_ID_BCM7XXX_28, 0xfffffc00 },
+	{ PHY_BCM_OUI_4, 0xffff0000 },
+	{ PHY_BCM_OUI_5, 0xffffff00 },
+	{ }
+};
+
+static int __init bcm7xxx_phy_init(void)
+{
+	return phy_drivers_register(bcm7xxx_driver,
+			ARRAY_SIZE(bcm7xxx_driver));
+}
+
+static void __exit bcm7xxx_phy_exit(void)
+{
+	phy_drivers_unregister(bcm7xxx_driver,
+			ARRAY_SIZE(bcm7xxx_driver));
+}
+
+module_init(bcm7xxx_phy_init);
+module_exit(bcm7xxx_phy_exit);
+
+MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);
+
+MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Broadcom Corporation");
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@ -25,58 +25,6 @@
 #define BRCM_PHY_REV(phydev) \
 	((phydev)->drv->phy_id & ~((phydev)->drv->phy_id_mask))

-
-#define MII_BCM54XX_ECR		0x10	/* BCM54xx extended control register */
-#define MII_BCM54XX_ECR_IM	0x1000	/* Interrupt mask */
-#define MII_BCM54XX_ECR_IF	0x0800	/* Interrupt force */
-
-#define MII_BCM54XX_ESR		0x11	/* BCM54xx extended status register */
-#define MII_BCM54XX_ESR_IS	0x1000	/* Interrupt status */
-
-#define MII_BCM54XX_EXP_DATA	0x15	/* Expansion register data */
-#define MII_BCM54XX_EXP_SEL	0x17	/* Expansion register select */
-#define MII_BCM54XX_EXP_SEL_SSD	0x0e00	/* Secondary SerDes select */
-#define MII_BCM54XX_EXP_SEL_ER	0x0f00	/* Expansion register select */
-
-#define MII_BCM54XX_AUX_CTL	0x18	/* Auxiliary control register */
-#define MII_BCM54XX_ISR		0x1a	/* BCM54xx interrupt status register */
-#define MII_BCM54XX_IMR		0x1b	/* BCM54xx interrupt mask register */
-#define MII_BCM54XX_INT_CRCERR	0x0001	/* CRC error */
-#define MII_BCM54XX_INT_LINK	0x0002	/* Link status changed */
-#define MII_BCM54XX_INT_SPEED	0x0004	/* Link speed change */
-#define MII_BCM54XX_INT_DUPLEX	0x0008	/* Duplex mode changed */
-#define MII_BCM54XX_INT_LRS	0x0010	/* Local receiver status changed */
-#define MII_BCM54XX_INT_RRS	0x0020	/* Remote receiver status changed */
-#define MII_BCM54XX_INT_SSERR	0x0040	/* Scrambler synchronization error */
-#define MII_BCM54XX_INT_UHCD	0x0080	/* Unsupported HCD negotiated */
-#define MII_BCM54XX_INT_NHCD	0x0100	/* No HCD */
-#define MII_BCM54XX_INT_NHCDL	0x0200	/* No HCD link */
-#define MII_BCM54XX_INT_ANPR	0x0400	/* Auto-negotiation page received */
-#define MII_BCM54XX_INT_LC	0x0800	/* All counters below 128 */
-#define MII_BCM54XX_INT_HC	0x1000	/* Counter above 32768 */
-#define MII_BCM54XX_INT_MDIX	0x2000	/* MDIX status change */
-#define MII_BCM54XX_INT_PSERR	0x4000	/* Pair swap error */
-
-#define MII_BCM54XX_SHD		0x1c	/* 0x1c shadow registers */
-#define MII_BCM54XX_SHD_WRITE	0x8000
-#define MII_BCM54XX_SHD_VAL(x)	((x & 0x1f) << 10)
-#define MII_BCM54XX_SHD_DATA(x)	((x & 0x3ff) << 0)
-
-/*
- * AUXILIARY CONTROL SHADOW ACCESS REGISTERS.  (PHY REG 0x18)
- */
-#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
-#define MII_BCM54XX_AUXCTL_ACTL_TX_6DB		0x0400
-#define MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA	0x0800
-
-#define MII_BCM54XX_AUXCTL_MISC_WREN	0x8000
-#define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
-#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
-#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
-
-#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
-
-
 /*
 * Broadcom LED source encodings.  These are used in BCM5461, BCM5481,
 * BCM5482, and possibly some others.
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@ -305,7 +305,10 @@ int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd)

 	ethtool_cmd_speed_set(cmd, phydev->speed);
 	cmd->duplex = phydev->duplex;
-	cmd->port = PORT_MII;
+	if (phydev->interface == PHY_INTERFACE_MODE_MOCA)
+		cmd->port = PORT_BNC;
+	else
+		cmd->port = PORT_MII;
 	cmd->phy_address = phydev->addr;
 	cmd->transceiver = phy_is_internal(phydev) ?
 		XCVR_INTERNAL : XCVR_EXTERNAL;
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@ -13,10 +13,17 @@
 #define PHY_ID_BCM5461			0x002060c0
 #define PHY_ID_BCM57780			0x03625d90

+#define PHY_ID_BCM7366			0x600d8490
+#define PHY_ID_BCM7439			0x600d8480
+#define PHY_ID_BCM7445			0x600d8510
+#define PHY_ID_BCM7XXX_28		0x600d8400
+
 #define PHY_BCM_OUI_MASK		0xfffffc00
 #define PHY_BCM_OUI_1			0x00206000
 #define PHY_BCM_OUI_2			0x0143bc00
 #define PHY_BCM_OUI_3			0x03625c00
+#define PHY_BCM_OUI_4			0x600d0000
+#define PHY_BCM_OUI_5			0x03625e00


 #define PHY_BCM_FLAGS_MODE_COPPER	0x00000001
@ -31,6 +38,59 @@
 #define PHY_BRCM_EXT_IBND_TX_ENABLE	0x00002000
 #define PHY_BRCM_CLEAR_RGMII_MODE	0x00004000
 #define PHY_BRCM_DIS_TXCRXC_NOENRGY	0x00008000
+/* Broadcom BCM7xxx specific workarounds */
+#define PHY_BRCM_100MBPS_WAR		0x00010000
 #define PHY_BCM_FLAGS_VALID		0x80000000

+/* Broadcom BCM54XX register definitions, common to most Broadcom PHYs */
+#define MII_BCM54XX_ECR		0x10	/* BCM54xx extended control register */
+#define MII_BCM54XX_ECR_IM	0x1000	/* Interrupt mask */
+#define MII_BCM54XX_ECR_IF	0x0800	/* Interrupt force */
+
+#define MII_BCM54XX_ESR		0x11	/* BCM54xx extended status register */
+#define MII_BCM54XX_ESR_IS	0x1000	/* Interrupt status */
+
+#define MII_BCM54XX_EXP_DATA	0x15	/* Expansion register data */
+#define MII_BCM54XX_EXP_SEL	0x17	/* Expansion register select */
+#define MII_BCM54XX_EXP_SEL_SSD	0x0e00	/* Secondary SerDes select */
+#define MII_BCM54XX_EXP_SEL_ER	0x0f00	/* Expansion register select */
+
+#define MII_BCM54XX_AUX_CTL	0x18	/* Auxiliary control register */
+#define MII_BCM54XX_ISR		0x1a	/* BCM54xx interrupt status register */
+#define MII_BCM54XX_IMR		0x1b	/* BCM54xx interrupt mask register */
+#define MII_BCM54XX_INT_CRCERR	0x0001	/* CRC error */
+#define MII_BCM54XX_INT_LINK	0x0002	/* Link status changed */
+#define MII_BCM54XX_INT_SPEED	0x0004	/* Link speed change */
+#define MII_BCM54XX_INT_DUPLEX	0x0008	/* Duplex mode changed */
+#define MII_BCM54XX_INT_LRS	0x0010	/* Local receiver status changed */
+#define MII_BCM54XX_INT_RRS	0x0020	/* Remote receiver status changed */
+#define MII_BCM54XX_INT_SSERR	0x0040	/* Scrambler synchronization error */
+#define MII_BCM54XX_INT_UHCD	0x0080	/* Unsupported HCD negotiated */
+#define MII_BCM54XX_INT_NHCD	0x0100	/* No HCD */
+#define MII_BCM54XX_INT_NHCDL	0x0200	/* No HCD link */
+#define MII_BCM54XX_INT_ANPR	0x0400	/* Auto-negotiation page received */
+#define MII_BCM54XX_INT_LC	0x0800	/* All counters below 128 */
+#define MII_BCM54XX_INT_HC	0x1000	/* Counter above 32768 */
+#define MII_BCM54XX_INT_MDIX	0x2000	/* MDIX status change */
+#define MII_BCM54XX_INT_PSERR	0x4000	/* Pair swap error */
+
+#define MII_BCM54XX_SHD		0x1c	/* 0x1c shadow registers */
+#define MII_BCM54XX_SHD_WRITE	0x8000
+#define MII_BCM54XX_SHD_VAL(x)	((x & 0x1f) << 10)
+#define MII_BCM54XX_SHD_DATA(x)	((x & 0x3ff) << 0)
+
+/*
+ * AUXILIARY CONTROL SHADOW ACCESS REGISTERS.  (PHY REG 0x18)
+ */
+#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
+#define MII_BCM54XX_AUXCTL_ACTL_TX_6DB		0x0400
+#define MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA	0x0800
+
+#define MII_BCM54XX_AUXCTL_MISC_WREN	0x8000
+#define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
+#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
+#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
+
+#define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL	0x0000
+
 #endif /* _LINUX_BRCMPHY_H */
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@ -74,6 +74,7 @@ typedef enum {
 	PHY_INTERFACE_MODE_RTBI,
 	PHY_INTERFACE_MODE_SMII,
 	PHY_INTERFACE_MODE_XGMII,
+	PHY_INTERFACE_MODE_MOCA,
 	PHY_INTERFACE_MODE_MAX,
 } phy_interface_t;

@ -113,6 +114,8 @@ static inline const char *phy_modes(phy_interface_t interface)
 		return "smii";
 	case PHY_INTERFACE_MODE_XGMII:
 		return "xgmii";
+	case PHY_INTERFACE_MODE_MOCA:
+		return "moca";
 	default:
 		return "unknown";
 	}