diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 157b9b6f8485..1bd34d9a7b9e 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -5491,6 +5491,81 @@ static inline void mlxsw_reg_mtmp_unpack(char *payload, unsigned int *p_temp,
 		mlxsw_reg_mtmp_sensor_name_memcpy_from(payload, sensor_name);
 }
 
+/* MCIA - Management Cable Info Access
+ * -----------------------------------
+ * MCIA register is used to access the SFP+ and QSFP connector's EPROM.
+ */
+
+#define MLXSW_REG_MCIA_ID 0x9014
+#define MLXSW_REG_MCIA_LEN 0x40
+
+MLXSW_REG_DEFINE(mcia, MLXSW_REG_MCIA_ID, MLXSW_REG_MCIA_LEN);
+
+/* reg_mcia_l
+ * Lock bit. Setting this bit will lock the access to the specific
+ * cable. Used for updating a full page in a cable EPROM. Any access
+ * other then subsequence writes will fail while the port is locked.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mcia, l, 0x00, 31, 1);
+
+/* reg_mcia_module
+ * Module number.
+ * Access: Index
+ */
+MLXSW_ITEM32(reg, mcia, module, 0x00, 16, 8);
+
+/* reg_mcia_status
+ * Module status.
+ * Access: RO
+ */
+MLXSW_ITEM32(reg, mcia, status, 0x00, 0, 8);
+
+/* reg_mcia_i2c_device_address
+ * I2C device address.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mcia, i2c_device_address, 0x04, 24, 8);
+
+/* reg_mcia_page_number
+ * Page number.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mcia, page_number, 0x04, 16, 8);
+
+/* reg_mcia_device_address
+ * Device address.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mcia, device_address, 0x04, 0, 16);
+
+/* reg_mcia_size
+ * Number of bytes to read/write (up to 48 bytes).
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mcia, size, 0x08, 0, 16);
+
+#define MLXSW_SP_REG_MCIA_EEPROM_SIZE 48
+
+/* reg_mcia_eeprom
+ * Bytes to read/write.
+ * Access: RW
+ */
+MLXSW_ITEM_BUF(reg, mcia, eeprom, 0x10, MLXSW_SP_REG_MCIA_EEPROM_SIZE);
+
+static inline void mlxsw_reg_mcia_pack(char *payload, u8 module, u8 lock,
+				       u8 page_number, u16 device_addr,
+				       u8 size, u8 i2c_device_addr)
+{
+	MLXSW_REG_ZERO(mcia, payload);
+	mlxsw_reg_mcia_module_set(payload, module);
+	mlxsw_reg_mcia_l_set(payload, lock);
+	mlxsw_reg_mcia_page_number_set(payload, page_number);
+	mlxsw_reg_mcia_device_address_set(payload, device_addr);
+	mlxsw_reg_mcia_size_set(payload, size);
+	mlxsw_reg_mcia_i2c_device_address_set(payload, i2c_device_addr);
+}
+
 /* MPAT - Monitoring Port Analyzer Table
  * -------------------------------------
  * MPAT Register is used to query and configure the Switch PortAnalyzer Table.
@@ -6433,6 +6508,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(mfsl),
 	MLXSW_REG(mtcap),
 	MLXSW_REG(mtmp),
+	MLXSW_REG(mcia),
 	MLXSW_REG(mpat),
 	MLXSW_REG(mpar),
 	MLXSW_REG(mlcr),