diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c index 85156fb53b62..a39afcf03e2c 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c @@ -44,9 +44,8 @@ static void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw); static void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw); static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw); -static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, - ixgbe_link_speed speed, - bool autoneg_wait_to_complete); +static void +ixgbe_set_hard_rate_select_speed(struct ixgbe_hw *, ixgbe_link_speed); static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw, ixgbe_link_speed speed, bool autoneg_wait_to_complete); @@ -109,6 +108,9 @@ static void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw) if (hw->phy.multispeed_fiber) { /* Set up dual speed SFP+ support */ mac->ops.setup_link = &ixgbe_setup_mac_link_multispeed_fiber; + mac->ops.setup_mac_link = ixgbe_setup_mac_link_82599; + mac->ops.set_rate_select_speed = + ixgbe_set_hard_rate_select_speed; } else { if ((mac->ops.get_media_type(hw) == ixgbe_media_type_backplane) && @@ -646,176 +648,32 @@ static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw) } /** - * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed - * @hw: pointer to hardware structure - * @speed: new link speed - * @autoneg_wait_to_complete: true when waiting for completion is needed + * ixgbe_set_hard_rate_select_speed - Set module link speed + * @hw: pointer to hardware structure + * @speed: link speed to set * - * Set the link speed in the AUTOC register and restarts link. - **/ -static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, - ixgbe_link_speed speed, - bool autoneg_wait_to_complete) + * Set module link speed via RS0/RS1 rate select pins. + */ +static void +ixgbe_set_hard_rate_select_speed(struct ixgbe_hw *hw, ixgbe_link_speed speed) { - s32 status = 0; - ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; - ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN; - u32 speedcnt = 0; u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); - u32 i = 0; - bool link_up = false; - bool autoneg = false; - /* Mask off requested but non-supported speeds */ - status = hw->mac.ops.get_link_capabilities(hw, &link_speed, - &autoneg); - if (status != 0) - return status; - - speed &= link_speed; - - /* - * Try each speed one by one, highest priority first. We do this in - * software because 10gb fiber doesn't support speed autonegotiation. - */ - if (speed & IXGBE_LINK_SPEED_10GB_FULL) { - speedcnt++; - highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; - - /* If we already have link at this speed, just jump out */ - status = hw->mac.ops.check_link(hw, &link_speed, &link_up, - false); - if (status != 0) - return status; - - if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up) - goto out; - - /* Set the module link speed */ - switch (hw->phy.media_type) { - case ixgbe_media_type_fiber: - esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5); - IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - IXGBE_WRITE_FLUSH(hw); - break; - case ixgbe_media_type_fiber_qsfp: - /* QSFP module automatically detects MAC link speed */ - break; - default: - hw_dbg(hw, "Unexpected media type.\n"); - break; - } - - /* Allow module to change analog characteristics (1G->10G) */ - msleep(40); - - status = ixgbe_setup_mac_link_82599(hw, - IXGBE_LINK_SPEED_10GB_FULL, - autoneg_wait_to_complete); - if (status != 0) - return status; - - /* Flap the tx laser if it has not already been done */ - if (hw->mac.ops.flap_tx_laser) - hw->mac.ops.flap_tx_laser(hw); - - /* - * Wait for the controller to acquire link. Per IEEE 802.3ap, - * Section 73.10.2, we may have to wait up to 500ms if KR is - * attempted. 82599 uses the same timing for 10g SFI. - */ - for (i = 0; i < 5; i++) { - /* Wait for the link partner to also set speed */ - msleep(100); - - /* If we have link, just jump out */ - status = hw->mac.ops.check_link(hw, &link_speed, - &link_up, false); - if (status != 0) - return status; - - if (link_up) - goto out; - } + switch (speed) { + case IXGBE_LINK_SPEED_10GB_FULL: + esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5); + break; + case IXGBE_LINK_SPEED_1GB_FULL: + esdp_reg &= ~IXGBE_ESDP_SDP5; + esdp_reg |= IXGBE_ESDP_SDP5_DIR; + break; + default: + hw_dbg(hw, "Invalid fixed module speed\n"); + return; } - if (speed & IXGBE_LINK_SPEED_1GB_FULL) { - speedcnt++; - if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) - highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; - - /* If we already have link at this speed, just jump out */ - status = hw->mac.ops.check_link(hw, &link_speed, &link_up, - false); - if (status != 0) - return status; - - if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up) - goto out; - - /* Set the module link speed */ - switch (hw->phy.media_type) { - case ixgbe_media_type_fiber: - esdp_reg &= ~IXGBE_ESDP_SDP5; - esdp_reg |= IXGBE_ESDP_SDP5_DIR; - IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - IXGBE_WRITE_FLUSH(hw); - break; - case ixgbe_media_type_fiber_qsfp: - /* QSFP module automatically detects MAC link speed */ - break; - default: - hw_dbg(hw, "Unexpected media type.\n"); - break; - } - - /* Allow module to change analog characteristics (10G->1G) */ - msleep(40); - - status = ixgbe_setup_mac_link_82599(hw, - IXGBE_LINK_SPEED_1GB_FULL, - autoneg_wait_to_complete); - if (status != 0) - return status; - - /* Flap the tx laser if it has not already been done */ - if (hw->mac.ops.flap_tx_laser) - hw->mac.ops.flap_tx_laser(hw); - - /* Wait for the link partner to also set speed */ - msleep(100); - - /* If we have link, just jump out */ - status = hw->mac.ops.check_link(hw, &link_speed, &link_up, - false); - if (status != 0) - return status; - - if (link_up) - goto out; - } - - /* - * We didn't get link. Configure back to the highest speed we tried, - * (if there was more than one). We call ourselves back with just the - * single highest speed that the user requested. - */ - if (speedcnt > 1) - status = ixgbe_setup_mac_link_multispeed_fiber(hw, - highest_link_speed, - autoneg_wait_to_complete); - -out: - /* Set autoneg_advertised value based on input link speed */ - hw->phy.autoneg_advertised = 0; - - if (speed & IXGBE_LINK_SPEED_10GB_FULL) - hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; - - if (speed & IXGBE_LINK_SPEED_1GB_FULL) - hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; - - return status; + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + IXGBE_WRITE_FLUSH(hw); } /** diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c index 3f56a8080118..2cd0c3a48a8d 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -3920,3 +3920,213 @@ bool ixgbe_mng_present(struct ixgbe_hw *hw) fwsm &= IXGBE_FWSM_MODE_MASK; return fwsm == IXGBE_FWSM_FW_MODE_PT; } + +/** + * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed + * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait_to_complete: true when waiting for completion is needed + * + * Set the link speed in the MAC and/or PHY register and restarts link. + */ +s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg_wait_to_complete) +{ + ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; + ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN; + s32 status = 0; + u32 speedcnt = 0; + u32 i = 0; + bool autoneg, link_up = false; + + /* Mask off requested but non-supported speeds */ + status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg); + if (status) + return status; + + speed &= link_speed; + + /* Try each speed one by one, highest priority first. We do this in + * software because 10Gb fiber doesn't support speed autonegotiation. + */ + if (speed & IXGBE_LINK_SPEED_10GB_FULL) { + speedcnt++; + highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; + + /* If we already have link at this speed, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, &link_up, + false); + if (status) + return status; + + if (link_speed == IXGBE_LINK_SPEED_10GB_FULL && link_up) + goto out; + + /* Set the module link speed */ + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + hw->mac.ops.set_rate_select_speed(hw, + IXGBE_LINK_SPEED_10GB_FULL); + break; + case ixgbe_media_type_fiber_qsfp: + /* QSFP module automatically detects MAC link speed */ + break; + default: + hw_dbg(hw, "Unexpected media type\n"); + break; + } + + /* Allow module to change analog characteristics (1G->10G) */ + msleep(40); + + status = hw->mac.ops.setup_mac_link(hw, + IXGBE_LINK_SPEED_10GB_FULL, + autoneg_wait_to_complete); + if (status) + return status; + + /* Flap the Tx laser if it has not already been done */ + if (hw->mac.ops.flap_tx_laser) + hw->mac.ops.flap_tx_laser(hw); + + /* Wait for the controller to acquire link. Per IEEE 802.3ap, + * Section 73.10.2, we may have to wait up to 500ms if KR is + * attempted. 82599 uses the same timing for 10g SFI. + */ + for (i = 0; i < 5; i++) { + /* Wait for the link partner to also set speed */ + msleep(100); + + /* If we have link, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, + &link_up, false); + if (status) + return status; + + if (link_up) + goto out; + } + } + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) { + speedcnt++; + if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) + highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; + + /* If we already have link at this speed, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, &link_up, + false); + if (status) + return status; + + if (link_speed == IXGBE_LINK_SPEED_1GB_FULL && link_up) + goto out; + + /* Set the module link speed */ + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + hw->mac.ops.set_rate_select_speed(hw, + IXGBE_LINK_SPEED_1GB_FULL); + break; + case ixgbe_media_type_fiber_qsfp: + /* QSFP module automatically detects link speed */ + break; + default: + hw_dbg(hw, "Unexpected media type\n"); + break; + } + + /* Allow module to change analog characteristics (10G->1G) */ + msleep(40); + + status = hw->mac.ops.setup_mac_link(hw, + IXGBE_LINK_SPEED_1GB_FULL, + autoneg_wait_to_complete); + if (status) + return status; + + /* Flap the Tx laser if it has not already been done */ + if (hw->mac.ops.flap_tx_laser) + hw->mac.ops.flap_tx_laser(hw); + + /* Wait for the link partner to also set speed */ + msleep(100); + + /* If we have link, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, &link_up, + false); + if (status) + return status; + + if (link_up) + goto out; + } + + /* We didn't get link. Configure back to the highest speed we tried, + * (if there was more than one). We call ourselves back with just the + * single highest speed that the user requested. + */ + if (speedcnt > 1) + status = ixgbe_setup_mac_link_multispeed_fiber(hw, + highest_link_speed, + autoneg_wait_to_complete); + +out: + /* Set autoneg_advertised value based on input link speed */ + hw->phy.autoneg_advertised = 0; + + if (speed & IXGBE_LINK_SPEED_10GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; + + return status; +} + +/** + * ixgbe_set_soft_rate_select_speed - Set module link speed + * @hw: pointer to hardware structure + * @speed: link speed to set + * + * Set module link speed via the soft rate select. + */ +void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw, + ixgbe_link_speed speed) +{ + s32 status; + u8 rs, eeprom_data; + + switch (speed) { + case IXGBE_LINK_SPEED_10GB_FULL: + /* one bit mask same as setting on */ + rs = IXGBE_SFF_SOFT_RS_SELECT_10G; + break; + case IXGBE_LINK_SPEED_1GB_FULL: + rs = IXGBE_SFF_SOFT_RS_SELECT_1G; + break; + default: + hw_dbg(hw, "Invalid fixed module speed\n"); + return; + } + + /* Set RS0 */ + status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + &eeprom_data); + if (status) { + hw_dbg(hw, "Failed to read Rx Rate Select RS0\n"); + return; + } + + eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; + + status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + eeprom_data); + if (status) { + hw_dbg(hw, "Failed to write Rx Rate Select RS0\n"); + return; + } +} diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h index 2f779f35dc4f..a0044e4a8b90 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h @@ -135,6 +135,11 @@ s32 ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw *hw); s32 ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw *hw); void ixgbe_disable_rx_generic(struct ixgbe_hw *hw); void ixgbe_enable_rx_generic(struct ixgbe_hw *hw); +s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg_wait_to_complete); +void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw, + ixgbe_link_speed speed); #define IXGBE_FAILED_READ_REG 0xffffffffU #define IXGBE_FAILED_READ_CFG_DWORD 0xffffffffU diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h index 0769b40399ea..824a2636aa9a 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h @@ -66,6 +66,9 @@ #define IXGBE_SFF_1GBASET_CAPABLE 0x8 #define IXGBE_SFF_10GBASESR_CAPABLE 0x10 #define IXGBE_SFF_10GBASELR_CAPABLE 0x20 +#define IXGBE_SFF_SOFT_RS_SELECT_MASK 0x8 +#define IXGBE_SFF_SOFT_RS_SELECT_10G 0x8 +#define IXGBE_SFF_SOFT_RS_SELECT_1G 0x0 #define IXGBE_SFF_ADDRESSING_MODE 0x4 #define IXGBE_SFF_QSFP_DA_ACTIVE_CABLE 0x1 #define IXGBE_SFF_QSFP_DA_PASSIVE_CABLE 0x8 diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h index 3be743b4f6ba..deef530348a0 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h @@ -3256,9 +3256,11 @@ struct ixgbe_mac_operations { void (*flap_tx_laser)(struct ixgbe_hw *); void (*stop_link_on_d3)(struct ixgbe_hw *); s32 (*setup_link)(struct ixgbe_hw *, ixgbe_link_speed, bool); + s32 (*setup_mac_link)(struct ixgbe_hw *, ixgbe_link_speed, bool); s32 (*check_link)(struct ixgbe_hw *, ixgbe_link_speed *, bool *, bool); s32 (*get_link_capabilities)(struct ixgbe_hw *, ixgbe_link_speed *, bool *); + void (*set_rate_select_speed)(struct ixgbe_hw *, ixgbe_link_speed); /* Packet Buffer Manipulation */ void (*set_rxpba)(struct ixgbe_hw *, int, u32, int); diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c index 2a1dca6e8d44..c6ae72bc92a0 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c @@ -909,6 +909,20 @@ static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed) return status; } +/** + * ixgbe_setup_mac_link_sfp_x550em - Configure the KR PHY for SFP. + * @hw: pointer to hardware structure + * + * Configures the extern PHY and the integrated KR PHY for SFP support. + */ +static s32 +ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + __always_unused bool autoneg_wait_to_complete) +{ + return ixgbe_setup_ixfi_x550em(hw, &speed); +} + /** * ixgbe_setup_mac_link_t_X550em - Sets the auto advertised link speed * @hw: pointer to hardware structure @@ -1003,6 +1017,10 @@ static void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw) mac->ops.disable_tx_laser = NULL; mac->ops.enable_tx_laser = NULL; mac->ops.flap_tx_laser = NULL; + mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber; + mac->ops.setup_mac_link = ixgbe_setup_mac_link_sfp_x550em; + mac->ops.set_rate_select_speed = + ixgbe_set_soft_rate_select_speed; break; case ixgbe_media_type_copper: mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;