mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-24 05:00:55 +07:00
docs: split up serial-interfaces.rst
It never made sense to keep these documents together; move each into its own file. Drop the section numbering on hsi.txt on its way to its own file. Suggested-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit is contained in:
Jonathan Corbet
parent
70fc1f547a
commit
5e99578685
88
Documentation/driver-api/hsi.rst
Normal file
88
Documentation/driver-api/hsi.rst
Normal file
@ -0,0 +1,88 @@
|
||||
High Speed Synchronous Serial Interface (HSI)
|
||||
=============================================
|
||||
|
||||
Introduction
|
||||
---------------
|
||||
|
||||
High Speed Syncronous Interface (HSI) is a fullduplex, low latency protocol,
|
||||
that is optimized for die-level interconnect between an Application Processor
|
||||
and a Baseband chipset. It has been specified by the MIPI alliance in 2003 and
|
||||
implemented by multiple vendors since then.
|
||||
|
||||
The HSI interface supports full duplex communication over multiple channels
|
||||
(typically 8) and is capable of reaching speeds up to 200 Mbit/s.
|
||||
|
||||
The serial protocol uses two signals, DATA and FLAG as combined data and clock
|
||||
signals and an additional READY signal for flow control. An additional WAKE
|
||||
signal can be used to wakeup the chips from standby modes. The signals are
|
||||
commonly prefixed by AC for signals going from the application die to the
|
||||
cellular die and CA for signals going the other way around.
|
||||
|
||||
::
|
||||
|
||||
+------------+ +---------------+
|
||||
| Cellular | | Application |
|
||||
| Die | | Die |
|
||||
| | - - - - - - CAWAKE - - - - - - >| |
|
||||
| T|------------ CADATA ------------>|R |
|
||||
| X|------------ CAFLAG ------------>|X |
|
||||
| |<----------- ACREADY ------------| |
|
||||
| | | |
|
||||
| | | |
|
||||
| |< - - - - - ACWAKE - - - - - - -| |
|
||||
| R|<----------- ACDATA -------------|T |
|
||||
| X|<----------- ACFLAG -------------|X |
|
||||
| |------------ CAREADY ----------->| |
|
||||
| | | |
|
||||
| | | |
|
||||
+------------+ +---------------+
|
||||
|
||||
HSI Subsystem in Linux
|
||||
-------------------------
|
||||
|
||||
In the Linux kernel the hsi subsystem is supposed to be used for HSI devices.
|
||||
The hsi subsystem contains drivers for hsi controllers including support for
|
||||
multi-port controllers and provides a generic API for using the HSI ports.
|
||||
|
||||
It also contains HSI client drivers, which make use of the generic API to
|
||||
implement a protocol used on the HSI interface. These client drivers can
|
||||
use an arbitrary number of channels.
|
||||
|
||||
hsi-char Device
|
||||
------------------
|
||||
|
||||
Each port automatically registers a generic client driver called hsi_char,
|
||||
which provides a charecter device for userspace representing the HSI port.
|
||||
It can be used to communicate via HSI from userspace. Userspace may
|
||||
configure the hsi_char device using the following ioctl commands:
|
||||
|
||||
HSC_RESET
|
||||
flush the HSI port
|
||||
|
||||
HSC_SET_PM
|
||||
enable or disable the client.
|
||||
|
||||
HSC_SEND_BREAK
|
||||
send break
|
||||
|
||||
HSC_SET_RX
|
||||
set RX configuration
|
||||
|
||||
HSC_GET_RX
|
||||
get RX configuration
|
||||
|
||||
HSC_SET_TX
|
||||
set TX configuration
|
||||
|
||||
HSC_GET_TX
|
||||
get TX configuration
|
||||
|
||||
The kernel HSI API
|
||||
------------------
|
||||
|
||||
.. kernel-doc:: include/linux/hsi/hsi.h
|
||||
:internal:
|
||||
|
||||
.. kernel-doc:: drivers/hsi/hsi_core.c
|
||||
:export:
|
||||
|
||||
46
Documentation/driver-api/i2c.rst
Normal file
46
Documentation/driver-api/i2c.rst
Normal file
@ -0,0 +1,46 @@
|
||||
I\ :sup:`2`\ C and SMBus Subsystem
|
||||
==================================
|
||||
|
||||
I\ :sup:`2`\ C (or without fancy typography, "I2C") is an acronym for
|
||||
the "Inter-IC" bus, a simple bus protocol which is widely used where low
|
||||
data rate communications suffice. Since it's also a licensed trademark,
|
||||
some vendors use another name (such as "Two-Wire Interface", TWI) for
|
||||
the same bus. I2C only needs two signals (SCL for clock, SDA for data),
|
||||
conserving board real estate and minimizing signal quality issues. Most
|
||||
I2C devices use seven bit addresses, and bus speeds of up to 400 kHz;
|
||||
there's a high speed extension (3.4 MHz) that's not yet found wide use.
|
||||
I2C is a multi-master bus; open drain signaling is used to arbitrate
|
||||
between masters, as well as to handshake and to synchronize clocks from
|
||||
slower clients.
|
||||
|
||||
The Linux I2C programming interfaces support only the master side of bus
|
||||
interactions, not the slave side. The programming interface is
|
||||
structured around two kinds of driver, and two kinds of device. An I2C
|
||||
"Adapter Driver" abstracts the controller hardware; it binds to a
|
||||
physical device (perhaps a PCI device or platform_device) and exposes a
|
||||
:c:type:`struct i2c_adapter <i2c_adapter>` representing each
|
||||
I2C bus segment it manages. On each I2C bus segment will be I2C devices
|
||||
represented by a :c:type:`struct i2c_client <i2c_client>`.
|
||||
Those devices will be bound to a :c:type:`struct i2c_driver
|
||||
<i2c_driver>`, which should follow the standard Linux driver
|
||||
model. (At this writing, a legacy model is more widely used.) There are
|
||||
functions to perform various I2C protocol operations; at this writing
|
||||
all such functions are usable only from task context.
|
||||
|
||||
The System Management Bus (SMBus) is a sibling protocol. Most SMBus
|
||||
systems are also I2C conformant. The electrical constraints are tighter
|
||||
for SMBus, and it standardizes particular protocol messages and idioms.
|
||||
Controllers that support I2C can also support most SMBus operations, but
|
||||
SMBus controllers don't support all the protocol options that an I2C
|
||||
controller will. There are functions to perform various SMBus protocol
|
||||
operations, either using I2C primitives or by issuing SMBus commands to
|
||||
i2c_adapter devices which don't support those I2C operations.
|
||||
|
||||
.. kernel-doc:: include/linux/i2c.h
|
||||
:internal:
|
||||
|
||||
.. kernel-doc:: drivers/i2c/i2c-boardinfo.c
|
||||
:functions: i2c_register_board_info
|
||||
|
||||
.. kernel-doc:: drivers/i2c/i2c-core.c
|
||||
:export:
|
||||
@ -20,5 +20,7 @@ available subsections can be seen below.
|
||||
sound
|
||||
frame-buffer
|
||||
input
|
||||
serial-interfaces
|
||||
spi
|
||||
i2c
|
||||
hsi
|
||||
miscellaneous
|
||||
|
||||
@ -1,189 +0,0 @@
|
||||
Serial Peripheral Interface (SPI)
|
||||
=================================
|
||||
|
||||
SPI is the "Serial Peripheral Interface", widely used with embedded
|
||||
systems because it is a simple and efficient interface: basically a
|
||||
multiplexed shift register. Its three signal wires hold a clock (SCK,
|
||||
often in the range of 1-20 MHz), a "Master Out, Slave In" (MOSI) data
|
||||
line, and a "Master In, Slave Out" (MISO) data line. SPI is a full
|
||||
duplex protocol; for each bit shifted out the MOSI line (one per clock)
|
||||
another is shifted in on the MISO line. Those bits are assembled into
|
||||
words of various sizes on the way to and from system memory. An
|
||||
additional chipselect line is usually active-low (nCS); four signals are
|
||||
normally used for each peripheral, plus sometimes an interrupt.
|
||||
|
||||
The SPI bus facilities listed here provide a generalized interface to
|
||||
declare SPI busses and devices, manage them according to the standard
|
||||
Linux driver model, and perform input/output operations. At this time,
|
||||
only "master" side interfaces are supported, where Linux talks to SPI
|
||||
peripherals and does not implement such a peripheral itself. (Interfaces
|
||||
to support implementing SPI slaves would necessarily look different.)
|
||||
|
||||
The programming interface is structured around two kinds of driver, and
|
||||
two kinds of device. A "Controller Driver" abstracts the controller
|
||||
hardware, which may be as simple as a set of GPIO pins or as complex as
|
||||
a pair of FIFOs connected to dual DMA engines on the other side of the
|
||||
SPI shift register (maximizing throughput). Such drivers bridge between
|
||||
whatever bus they sit on (often the platform bus) and SPI, and expose
|
||||
the SPI side of their device as a :c:type:`struct spi_master
|
||||
<spi_master>`. SPI devices are children of that master,
|
||||
represented as a :c:type:`struct spi_device <spi_device>` and
|
||||
manufactured from :c:type:`struct spi_board_info
|
||||
<spi_board_info>` descriptors which are usually provided by
|
||||
board-specific initialization code. A :c:type:`struct spi_driver
|
||||
<spi_driver>` is called a "Protocol Driver", and is bound to a
|
||||
spi_device using normal driver model calls.
|
||||
|
||||
The I/O model is a set of queued messages. Protocol drivers submit one
|
||||
or more :c:type:`struct spi_message <spi_message>` objects,
|
||||
which are processed and completed asynchronously. (There are synchronous
|
||||
wrappers, however.) Messages are built from one or more
|
||||
:c:type:`struct spi_transfer <spi_transfer>` objects, each of
|
||||
which wraps a full duplex SPI transfer. A variety of protocol tweaking
|
||||
options are needed, because different chips adopt very different
|
||||
policies for how they use the bits transferred with SPI.
|
||||
|
||||
.. kernel-doc:: include/linux/spi/spi.h
|
||||
:internal:
|
||||
|
||||
.. kernel-doc:: drivers/spi/spi.c
|
||||
:functions: spi_register_board_info
|
||||
|
||||
.. kernel-doc:: drivers/spi/spi.c
|
||||
:export:
|
||||
|
||||
I\ :sup:`2`\ C and SMBus Subsystem
|
||||
==================================
|
||||
|
||||
I\ :sup:`2`\ C (or without fancy typography, "I2C") is an acronym for
|
||||
the "Inter-IC" bus, a simple bus protocol which is widely used where low
|
||||
data rate communications suffice. Since it's also a licensed trademark,
|
||||
some vendors use another name (such as "Two-Wire Interface", TWI) for
|
||||
the same bus. I2C only needs two signals (SCL for clock, SDA for data),
|
||||
conserving board real estate and minimizing signal quality issues. Most
|
||||
I2C devices use seven bit addresses, and bus speeds of up to 400 kHz;
|
||||
there's a high speed extension (3.4 MHz) that's not yet found wide use.
|
||||
I2C is a multi-master bus; open drain signaling is used to arbitrate
|
||||
between masters, as well as to handshake and to synchronize clocks from
|
||||
slower clients.
|
||||
|
||||
The Linux I2C programming interfaces support only the master side of bus
|
||||
interactions, not the slave side. The programming interface is
|
||||
structured around two kinds of driver, and two kinds of device. An I2C
|
||||
"Adapter Driver" abstracts the controller hardware; it binds to a
|
||||
physical device (perhaps a PCI device or platform_device) and exposes a
|
||||
:c:type:`struct i2c_adapter <i2c_adapter>` representing each
|
||||
I2C bus segment it manages. On each I2C bus segment will be I2C devices
|
||||
represented by a :c:type:`struct i2c_client <i2c_client>`.
|
||||
Those devices will be bound to a :c:type:`struct i2c_driver
|
||||
<i2c_driver>`, which should follow the standard Linux driver
|
||||
model. (At this writing, a legacy model is more widely used.) There are
|
||||
functions to perform various I2C protocol operations; at this writing
|
||||
all such functions are usable only from task context.
|
||||
|
||||
The System Management Bus (SMBus) is a sibling protocol. Most SMBus
|
||||
systems are also I2C conformant. The electrical constraints are tighter
|
||||
for SMBus, and it standardizes particular protocol messages and idioms.
|
||||
Controllers that support I2C can also support most SMBus operations, but
|
||||
SMBus controllers don't support all the protocol options that an I2C
|
||||
controller will. There are functions to perform various SMBus protocol
|
||||
operations, either using I2C primitives or by issuing SMBus commands to
|
||||
i2c_adapter devices which don't support those I2C operations.
|
||||
|
||||
.. kernel-doc:: include/linux/i2c.h
|
||||
:internal:
|
||||
|
||||
.. kernel-doc:: drivers/i2c/i2c-boardinfo.c
|
||||
:functions: i2c_register_board_info
|
||||
|
||||
.. kernel-doc:: drivers/i2c/i2c-core.c
|
||||
:export:
|
||||
|
||||
High Speed Synchronous Serial Interface (HSI)
|
||||
=============================================
|
||||
|
||||
1. Introduction
|
||||
---------------
|
||||
|
||||
High Speed Syncronous Interface (HSI) is a fullduplex, low latency protocol,
|
||||
that is optimized for die-level interconnect between an Application Processor
|
||||
and a Baseband chipset. It has been specified by the MIPI alliance in 2003 and
|
||||
implemented by multiple vendors since then.
|
||||
|
||||
The HSI interface supports full duplex communication over multiple channels
|
||||
(typically 8) and is capable of reaching speeds up to 200 Mbit/s.
|
||||
|
||||
The serial protocol uses two signals, DATA and FLAG as combined data and clock
|
||||
signals and an additional READY signal for flow control. An additional WAKE
|
||||
signal can be used to wakeup the chips from standby modes. The signals are
|
||||
commonly prefixed by AC for signals going from the application die to the
|
||||
cellular die and CA for signals going the other way around.
|
||||
|
||||
::
|
||||
|
||||
+------------+ +---------------+
|
||||
| Cellular | | Application |
|
||||
| Die | | Die |
|
||||
| | - - - - - - CAWAKE - - - - - - >| |
|
||||
| T|------------ CADATA ------------>|R |
|
||||
| X|------------ CAFLAG ------------>|X |
|
||||
| |<----------- ACREADY ------------| |
|
||||
| | | |
|
||||
| | | |
|
||||
| |< - - - - - ACWAKE - - - - - - -| |
|
||||
| R|<----------- ACDATA -------------|T |
|
||||
| X|<----------- ACFLAG -------------|X |
|
||||
| |------------ CAREADY ----------->| |
|
||||
| | | |
|
||||
| | | |
|
||||
+------------+ +---------------+
|
||||
|
||||
2. HSI Subsystem in Linux
|
||||
-------------------------
|
||||
|
||||
In the Linux kernel the hsi subsystem is supposed to be used for HSI devices.
|
||||
The hsi subsystem contains drivers for hsi controllers including support for
|
||||
multi-port controllers and provides a generic API for using the HSI ports.
|
||||
|
||||
It also contains HSI client drivers, which make use of the generic API to
|
||||
implement a protocol used on the HSI interface. These client drivers can
|
||||
use an arbitrary number of channels.
|
||||
|
||||
3. hsi-char Device
|
||||
------------------
|
||||
|
||||
Each port automatically registers a generic client driver called hsi_char,
|
||||
which provides a charecter device for userspace representing the HSI port.
|
||||
It can be used to communicate via HSI from userspace. Userspace may
|
||||
configure the hsi_char device using the following ioctl commands:
|
||||
|
||||
HSC_RESET
|
||||
flush the HSI port
|
||||
|
||||
HSC_SET_PM
|
||||
enable or disable the client.
|
||||
|
||||
HSC_SEND_BREAK
|
||||
send break
|
||||
|
||||
HSC_SET_RX
|
||||
set RX configuration
|
||||
|
||||
HSC_GET_RX
|
||||
get RX configuration
|
||||
|
||||
HSC_SET_TX
|
||||
set TX configuration
|
||||
|
||||
HSC_GET_TX
|
||||
get TX configuration
|
||||
|
||||
The kernel HSI API
|
||||
------------------
|
||||
|
||||
.. kernel-doc:: include/linux/hsi/hsi.h
|
||||
:internal:
|
||||
|
||||
.. kernel-doc:: drivers/hsi/hsi_core.c
|
||||
:export:
|
||||
|
||||
53
Documentation/driver-api/spi.rst
Normal file
53
Documentation/driver-api/spi.rst
Normal file
@ -0,0 +1,53 @@
|
||||
Serial Peripheral Interface (SPI)
|
||||
=================================
|
||||
|
||||
SPI is the "Serial Peripheral Interface", widely used with embedded
|
||||
systems because it is a simple and efficient interface: basically a
|
||||
multiplexed shift register. Its three signal wires hold a clock (SCK,
|
||||
often in the range of 1-20 MHz), a "Master Out, Slave In" (MOSI) data
|
||||
line, and a "Master In, Slave Out" (MISO) data line. SPI is a full
|
||||
duplex protocol; for each bit shifted out the MOSI line (one per clock)
|
||||
another is shifted in on the MISO line. Those bits are assembled into
|
||||
words of various sizes on the way to and from system memory. An
|
||||
additional chipselect line is usually active-low (nCS); four signals are
|
||||
normally used for each peripheral, plus sometimes an interrupt.
|
||||
|
||||
The SPI bus facilities listed here provide a generalized interface to
|
||||
declare SPI busses and devices, manage them according to the standard
|
||||
Linux driver model, and perform input/output operations. At this time,
|
||||
only "master" side interfaces are supported, where Linux talks to SPI
|
||||
peripherals and does not implement such a peripheral itself. (Interfaces
|
||||
to support implementing SPI slaves would necessarily look different.)
|
||||
|
||||
The programming interface is structured around two kinds of driver, and
|
||||
two kinds of device. A "Controller Driver" abstracts the controller
|
||||
hardware, which may be as simple as a set of GPIO pins or as complex as
|
||||
a pair of FIFOs connected to dual DMA engines on the other side of the
|
||||
SPI shift register (maximizing throughput). Such drivers bridge between
|
||||
whatever bus they sit on (often the platform bus) and SPI, and expose
|
||||
the SPI side of their device as a :c:type:`struct spi_master
|
||||
<spi_master>`. SPI devices are children of that master,
|
||||
represented as a :c:type:`struct spi_device <spi_device>` and
|
||||
manufactured from :c:type:`struct spi_board_info
|
||||
<spi_board_info>` descriptors which are usually provided by
|
||||
board-specific initialization code. A :c:type:`struct spi_driver
|
||||
<spi_driver>` is called a "Protocol Driver", and is bound to a
|
||||
spi_device using normal driver model calls.
|
||||
|
||||
The I/O model is a set of queued messages. Protocol drivers submit one
|
||||
or more :c:type:`struct spi_message <spi_message>` objects,
|
||||
which are processed and completed asynchronously. (There are synchronous
|
||||
wrappers, however.) Messages are built from one or more
|
||||
:c:type:`struct spi_transfer <spi_transfer>` objects, each of
|
||||
which wraps a full duplex SPI transfer. A variety of protocol tweaking
|
||||
options are needed, because different chips adopt very different
|
||||
policies for how they use the bits transferred with SPI.
|
||||
|
||||
.. kernel-doc:: include/linux/spi/spi.h
|
||||
:internal:
|
||||
|
||||
.. kernel-doc:: drivers/spi/spi.c
|
||||
:functions: spi_register_board_info
|
||||
|
||||
.. kernel-doc:: drivers/spi/spi.c
|
||||
:export:
|
||||
Loading…
Reference in New Issue
Block a user