From 37ff1b0df37af1f45d94674c83f65fc5ad4a3c73 Mon Sep 17 00:00:00 2001 From: Marcin Rokicki Date: Mon, 20 Feb 2017 15:38:50 +0100 Subject: [PATCH] ath10k: clean header files from bad block comments Fix output from checkpatch.pl like: Block comments use a trailing */ on a separate line Signed-off-by: Marcin Rokicki Signed-off-by: Kalle Valo --- drivers/net/wireless/ath/ath10k/bmi.h | 3 ++- drivers/net/wireless/ath/ath10k/core.h | 9 ++++--- drivers/net/wireless/ath/ath10k/hif.h | 6 +++-- drivers/net/wireless/ath/ath10k/htt.h | 24 +++++++++++------ drivers/net/wireless/ath/ath10k/hw.h | 3 ++- drivers/net/wireless/ath/ath10k/rx_desc.h | 13 +++++---- drivers/net/wireless/ath/ath10k/targaddrs.h | 19 ++++++------- drivers/net/wireless/ath/ath10k/wmi-ops.h | 3 ++- drivers/net/wireless/ath/ath10k/wmi.h | 30 ++++++++++++++------- 9 files changed, 70 insertions(+), 40 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/bmi.h b/drivers/net/wireless/ath/ath10k/bmi.h index a65f26267fe3..cc45b63ade15 100644 --- a/drivers/net/wireless/ath/ath10k/bmi.h +++ b/drivers/net/wireless/ath/ath10k/bmi.h @@ -176,7 +176,8 @@ union bmi_resp { } rompatch_uninstall; struct { /* 0 = nothing executed - * otherwise = NVRAM segment return value */ + * otherwise = NVRAM segment return value + */ __le32 result; } nvram_process; u8 payload[BMI_MAX_CMDBUF_SIZE]; diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h index d4b9a0ec1bdc..bf091514ecc6 100644 --- a/drivers/net/wireless/ath/ath10k/core.h +++ b/drivers/net/wireless/ath/ath10k/core.h @@ -501,14 +501,16 @@ enum ath10k_state { * stopped in ath10k_core_restart() work holding conf_mutex. The state * RESTARTED means that the device is up and mac80211 has started hw * reconfiguration. Once mac80211 is done with the reconfiguration we - * set the state to STATE_ON in reconfig_complete(). */ + * set the state to STATE_ON in reconfig_complete(). + */ ATH10K_STATE_RESTARTING, ATH10K_STATE_RESTARTED, /* The device has crashed while restarting hw. This state is like ON * but commands are blocked in HTC and -ECOMM response is given. This * prevents completion timeouts and makes the driver more responsive to - * userspace commands. This is also prevents recursive recovery. */ + * userspace commands. This is also prevents recursive recovery. + */ ATH10K_STATE_WEDGED, /* factory tests */ @@ -920,7 +922,8 @@ struct ath10k { struct work_struct restart_work; /* cycle count is reported twice for each visited channel during scan. - * access protected by data_lock */ + * access protected by data_lock + */ u32 survey_last_rx_clear_count; u32 survey_last_cycle_count; struct survey_info survey[ATH10K_NUM_CHANS]; diff --git a/drivers/net/wireless/ath/ath10k/hif.h b/drivers/net/wireless/ath/ath10k/hif.h index b2566b06e1e1..6679dd9cfd12 100644 --- a/drivers/net/wireless/ath/ath10k/hif.h +++ b/drivers/net/wireless/ath/ath10k/hif.h @@ -54,7 +54,8 @@ struct ath10k_hif_ops { int (*start)(struct ath10k *ar); /* Clean up what start() did. This does not revert to BMI phase. If - * desired so, call power_down() and power_up() */ + * desired so, call power_down() and power_up() + */ void (*stop)(struct ath10k *ar); int (*map_service_to_pipe)(struct ath10k *ar, u16 service_id, @@ -82,7 +83,8 @@ struct ath10k_hif_ops { int (*power_up)(struct ath10k *ar); /* Power down the device and free up resources. stop() must be called - * before this if start() was called earlier */ + * before this if start() was called earlier + */ void (*power_down)(struct ath10k *ar); int (*suspend)(struct ath10k *ar); diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h index 90c2f72666b8..6305308422c4 100644 --- a/drivers/net/wireless/ath/ath10k/htt.h +++ b/drivers/net/wireless/ath/ath10k/htt.h @@ -51,7 +51,8 @@ enum htt_h2t_msg_type { /* host-to-target */ HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG = 6, /* This command is used for sending management frames in HTT < 3.0. - * HTT >= 3.0 uses TX_FRM for everything. */ + * HTT >= 3.0 uses TX_FRM for everything. + */ HTT_H2T_MSG_TYPE_MGMT_TX = 7, HTT_H2T_MSG_TYPE_TX_FETCH_RESP = 11, @@ -910,7 +911,8 @@ struct htt_rx_test { /* payload consists of 2 lists: * a) num_ints * sizeof(__le32) - * b) num_chars * sizeof(u8) aligned to 4bytes */ + * b) num_chars * sizeof(u8) aligned to 4bytes + */ u8 payload[0]; } __packed; @@ -1307,7 +1309,8 @@ struct htt_frag_desc_bank_id { } __packed; /* real is 16 but it wouldn't fit in the max htt message size - * so we use a conservatively safe value for now */ + * so we use a conservatively safe value for now + */ #define HTT_FRAG_DESC_BANK_MAX 4 #define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK 0x03 @@ -1684,12 +1687,14 @@ struct ath10k_htt { DECLARE_KFIFO_PTR(txdone_fifo, struct htt_tx_done); /* set if host-fw communication goes haywire - * used to avoid further failures */ + * used to avoid further failures + */ bool rx_confused; atomic_t num_mpdus_ready; /* This is used to group tx/rx completions separately and process them - * in batches to reduce cache stalls */ + * in batches to reduce cache stalls + */ struct sk_buff_head rx_compl_q; struct sk_buff_head rx_in_ord_compl_q; struct sk_buff_head tx_fetch_ind_q; @@ -1725,11 +1730,13 @@ struct ath10k_htt { /* This structure layout is programmed via rx ring setup * so that FW knows how to transfer the rx descriptor to the host. - * Buffers like this are placed on the rx ring. */ + * Buffers like this are placed on the rx ring. + */ struct htt_rx_desc { union { /* This field is filled on the host using the msdu buffer - * from htt_rx_indication */ + * from htt_rx_indication + */ struct fw_rx_desc_base fw_desc; u32 pad; } __packed; @@ -1760,7 +1767,8 @@ struct htt_rx_desc { #define HTT_RX_MSDU_SIZE (HTT_RX_BUF_SIZE - (int)sizeof(struct htt_rx_desc)) /* Refill a bunch of RX buffers for each refill round so that FW/HW can handle - * aggregated traffic more nicely. */ + * aggregated traffic more nicely. + */ #define ATH10K_HTT_MAX_NUM_REFILL 100 /* diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h index d370b573e0f9..8aca62bca348 100644 --- a/drivers/net/wireless/ath/ath10k/hw.h +++ b/drivers/net/wireless/ath/ath10k/hw.h @@ -296,7 +296,8 @@ void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey, * - raw appears in nwifi decap, raw and nwifi appear in ethernet decap * - raw have FCS, nwifi doesn't * - ethernet frames have 802.11 header decapped and parts (base hdr, cipher - * param, llc/snap) are aligned to 4byte boundaries each */ + * param, llc/snap) are aligned to 4byte boundaries each + */ enum ath10k_hw_txrx_mode { ATH10K_HW_TXRX_RAW = 0, diff --git a/drivers/net/wireless/ath/ath10k/rx_desc.h b/drivers/net/wireless/ath/ath10k/rx_desc.h index 034e7a54c5b2..c1022a1cf855 100644 --- a/drivers/net/wireless/ath/ath10k/rx_desc.h +++ b/drivers/net/wireless/ath/ath10k/rx_desc.h @@ -439,19 +439,22 @@ struct rx_mpdu_end { * c) A-MSDU subframe header (14 bytes) if appliable * d) LLC/SNAP (RFC1042, 8 bytes) * - * In case of A-MSDU only first frame in sequence contains (a) and (b). */ + * In case of A-MSDU only first frame in sequence contains (a) and (b). + */ enum rx_msdu_decap_format { RX_MSDU_DECAP_RAW = 0, /* Note: QoS frames are reported as non-QoS. The rx_hdr_status in - * htt_rx_desc contains the original decapped 802.11 header. */ + * htt_rx_desc contains the original decapped 802.11 header. + */ RX_MSDU_DECAP_NATIVE_WIFI = 1, /* Payload contains an ethernet header (struct ethhdr). */ RX_MSDU_DECAP_ETHERNET2_DIX = 2, /* Payload contains two 48-bit addresses and 2-byte length (14 bytes - * total), followed by an RFC1042 header (8 bytes). */ + * total), followed by an RFC1042 header (8 bytes). + */ RX_MSDU_DECAP_8023_SNAP_LLC = 3 }; @@ -867,7 +870,7 @@ struct rx_ppdu_start { * * reserved_9 * Reserved: HW should fill with 0, FW should ignore. -*/ + */ #define RX_PPDU_END_FLAGS_PHY_ERR (1 << 0) #define RX_PPDU_END_FLAGS_RX_LOCATION (1 << 1) @@ -1207,7 +1210,7 @@ struct rx_ppdu_end { * Every time HW sets this bit in memory FW/SW must clear this * bit in memory. FW will initialize all the ppdu_done dword * to 0. -*/ + */ #define FW_RX_DESC_INFO0_DISCARD (1 << 0) #define FW_RX_DESC_INFO0_FORWARD (1 << 1) diff --git a/drivers/net/wireless/ath/ath10k/targaddrs.h b/drivers/net/wireless/ath/ath10k/targaddrs.h index a47cab44d9c8..cbac9e4252d6 100644 --- a/drivers/net/wireless/ath/ath10k/targaddrs.h +++ b/drivers/net/wireless/ath/ath10k/targaddrs.h @@ -268,13 +268,13 @@ struct host_interest { #define HI_OPTION_FW_BRIDGE_SHIFT 0x04 /* -Fw Mode/SubMode Mask -|-----------------------------------------------------------------------------| -| SUB | SUB | SUB | SUB | | | | | -|MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0]| -| (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2) | -|-----------------------------------------------------------------------------| -*/ + * Fw Mode/SubMode Mask + *----------------------------------------------------------------------------- + * SUB | SUB | SUB | SUB | | | | + *MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0] + * (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2) + *----------------------------------------------------------------------------- + */ #define HI_OPTION_FW_MODE_BITS 0x2 #define HI_OPTION_FW_MODE_MASK 0x3 #define HI_OPTION_FW_MODE_SHIFT 0xC @@ -428,8 +428,9 @@ Fw Mode/SubMode Mask #define HI_PWR_SAVE_LPL_ENABLED 0x1 /*b1-b3 reserved*/ /*b4-b5 : dev0 LPL type : 0 - none - 1- Reduce Pwr Search - 2- Reduce Pwr Listen*/ + * 1- Reduce Pwr Search + * 2- Reduce Pwr Listen + */ /*b6-b7 : dev1 LPL type and so on for Max 8 devices*/ #define HI_PWR_SAVE_LPL_DEV0_LSB 4 #define HI_PWR_SAVE_LPL_DEV_MASK 0x3 diff --git a/drivers/net/wireless/ath/ath10k/wmi-ops.h b/drivers/net/wireless/ath/ath10k/wmi-ops.h index c7956e181f80..2fc3f24ff1ca 100644 --- a/drivers/net/wireless/ath/ath10k/wmi-ops.h +++ b/drivers/net/wireless/ath/ath10k/wmi-ops.h @@ -390,7 +390,8 @@ ath10k_wmi_mgmt_tx(struct ath10k *ar, struct sk_buff *msdu) return ret; /* FIXME There's no ACK event for Management Tx. This probably - * shouldn't be called here either. */ + * shouldn't be called here either. + */ info->flags |= IEEE80211_TX_STAT_ACK; ieee80211_tx_status_irqsafe(ar->hw, msdu); diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h index cf385feb5707..1b4865a55595 100644 --- a/drivers/net/wireless/ath/ath10k/wmi.h +++ b/drivers/net/wireless/ath/ath10k/wmi.h @@ -1038,7 +1038,8 @@ enum wmi_cmd_id { WMI_STA_UAPSD_AUTO_TRIG_CMDID, /* STA Keep alive parameter configuration, - Requires WMI_SERVICE_STA_KEEP_ALIVE */ + * Requires WMI_SERVICE_STA_KEEP_ALIVE + */ WMI_STA_KEEPALIVE_CMD, /* misc command group */ @@ -1774,7 +1775,8 @@ static inline const char *ath10k_wmi_phymode_str(enum wmi_phy_mode mode) break; /* no default handler to allow compiler to check that the - * enum is fully handled */ + * enum is fully handled + */ }; return ""; @@ -2974,7 +2976,8 @@ struct wmi_start_scan_arg { /* When set, DFS channels will not be scanned */ #define WMI_SCAN_BYPASS_DFS_CHN 0x40 /* Different FW scan engine may choose to bail out on errors. - * Allow the driver to have influence over that. */ + * Allow the driver to have influence over that. + */ #define WMI_SCAN_CONTINUE_ON_ERROR 0x80 /* WMI_SCAN_CLASS_MASK must be the same value as IEEE80211_SCAN_CLASS_MASK */ @@ -4447,14 +4450,16 @@ enum wmi_vdev_subtype_10_4 { /* values for vdev_start_request flags */ /* * Indicates that AP VDEV uses hidden ssid. only valid for - * AP/GO */ + * AP/GO + */ #define WMI_VDEV_START_HIDDEN_SSID (1 << 0) /* * Indicates if robust management frame/management frame * protection is enabled. For GO/AP vdevs, it indicates that * it may support station/client associations with RMF enabled. * For STA/client vdevs, it indicates that sta will - * associate with AP with RMF enabled. */ + * associate with AP with RMF enabled. + */ #define WMI_VDEV_START_PMF_ENABLED (1 << 1) struct wmi_p2p_noa_descriptor { @@ -4814,7 +4819,8 @@ enum wmi_vdev_param { * An associated STA is considered unresponsive if there is no recent * TX/RX activity and downlink frames are buffered for it. Once a STA * exceeds the maximum unresponsive time, the AP will send a - * WMI_STA_KICKOUT event to the host so the STA can be deleted. */ + * WMI_STA_KICKOUT event to the host so the STA can be deleted. + */ WMI_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS, /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */ @@ -4941,7 +4947,8 @@ enum wmi_10x_vdev_param { * An associated STA is considered unresponsive if there is no recent * TX/RX activity and downlink frames are buffered for it. Once a STA * exceeds the maximum unresponsive time, the AP will send a - * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted. */ + * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted. + */ WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS, /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */ @@ -5605,12 +5612,14 @@ struct wmi_tim_info_arg { struct wmi_p2p_noa_info { /* Bit 0 - Flag to indicate an update in NOA schedule - Bits 7-1 - Reserved */ + * Bits 7-1 - Reserved + */ u8 changed; /* NOA index */ u8 index; /* Bit 0 - Opp PS state of the AP - Bits 1-7 - Ctwindow in TUs */ + * Bits 1-7 - Ctwindow in TUs + */ u8 ctwindow_oppps; /* Number of NOA descriptors */ u8 num_descriptors; @@ -6000,7 +6009,8 @@ struct wmi_main_peer_assoc_complete_cmd { struct wmi_common_peer_assoc_complete_cmd cmd; /* HT Operation Element of the peer. Five bytes packed in 2 - * INT32 array and filled from lsb to msb. */ + * INT32 array and filled from lsb to msb. + */ __le32 peer_ht_info[2]; } __packed;