diff --git a/Documentation/networking/e100.rst b/Documentation/networking/e100.rst index 9708f5fa76de..f81111eba9c5 100644 --- a/Documentation/networking/e100.rst +++ b/Documentation/networking/e100.rst @@ -47,41 +47,45 @@ Driver Configuration Parameters The default value for each parameter is generally the recommended setting, unless otherwise noted. -Rx Descriptors: Number of receive descriptors. A receive descriptor is a data +Rx Descriptors: + Number of receive descriptors. A receive descriptor is a data structure that describes a receive buffer and its attributes to the network controller. The data in the descriptor is used by the controller to write data from the controller to host memory. In the 3.x.x driver the valid range for this parameter is 64-256. The default value is 256. This parameter can be changed using the command:: - ethtool -G eth? rx n + ethtool -G eth? rx n Where n is the number of desired Rx descriptors. -Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data +Tx Descriptors: + Number of transmit descriptors. A transmit descriptor is a data structure that describes a transmit buffer and its attributes to the network controller. The data in the descriptor is used by the controller to read data from the host memory to the controller. In the 3.x.x driver the valid range for this parameter is 64-256. The default value is 128. This parameter can be changed using the command:: - ethtool -G eth? tx n + ethtool -G eth? tx n Where n is the number of desired Tx descriptors. -Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by +Speed/Duplex: + The driver auto-negotiates the link speed and duplex settings by default. The ethtool utility can be used as follows to force speed/duplex.:: - ethtool -s eth? autoneg off speed {10|100} duplex {full|half} + ethtool -s eth? autoneg off speed {10|100} duplex {full|half} NOTE: setting the speed/duplex to incorrect values will cause the link to fail. -Event Log Message Level: The driver uses the message level flag to log events +Event Log Message Level: + The driver uses the message level flag to log events to syslog. The message level can be set at driver load time. It can also be set using the command:: - ethtool -s eth? msglvl n + ethtool -s eth? msglvl n Additional Configurations @@ -92,7 +96,7 @@ Configuring the Driver on Different Distributions Configuring a network driver to load properly when the system is started is distribution dependent. Typically, the configuration process involves -adding an alias line to /etc/modprobe.d/*.conf as well as editing other +adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other system startup scripts and/or configuration files. Many popular Linux distributions ship with tools to make these changes for you. To learn the proper way to configure a network device for your system, refer to @@ -160,7 +164,10 @@ This results in unbalanced receive traffic. If you have multiple interfaces in a server, either turn on ARP filtering by -(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter +(1) entering:: + + echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter + (this only works if your kernel's version is higher than 2.4.5), or (2) installing the interfaces in separate broadcast domains (either diff --git a/Documentation/networking/e1000.rst b/Documentation/networking/e1000.rst index 144b87eef153..f10dd4086921 100644 --- a/Documentation/networking/e1000.rst +++ b/Documentation/networking/e1000.rst @@ -34,7 +34,8 @@ Command Line Parameters The default value for each parameter is generally the recommended setting, unless otherwise noted. -NOTES: For more information about the AutoNeg, Duplex, and Speed +NOTES: + For more information about the AutoNeg, Duplex, and Speed parameters, see the "Speed and Duplex Configuration" section in this document. @@ -45,22 +46,27 @@ NOTES: For more information about the AutoNeg, Duplex, and Speed AutoNeg ------- + (Supported only on adapters with copper connections) -Valid Range: 0x01-0x0F, 0x20-0x2F -Default Value: 0x2F + +:Valid Range: 0x01-0x0F, 0x20-0x2F +:Default Value: 0x2F This parameter is a bit-mask that specifies the speed and duplex settings advertised by the adapter. When this parameter is used, the Speed and Duplex parameters must not be specified. -NOTE: Refer to the Speed and Duplex section of this readme for more +NOTE: + Refer to the Speed and Duplex section of this readme for more information on the AutoNeg parameter. Duplex ------ + (Supported only on adapters with copper connections) -Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full) -Default Value: 0 + +:Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full) +:Default Value: 0 This defines the direction in which data is allowed to flow. Can be either one or two-directional. If both Duplex and the link partner are @@ -70,18 +76,22 @@ duplex. FlowControl ----------- -Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx) -Default Value: Reads flow control settings from the EEPROM + +:Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx) +:Default Value: Reads flow control settings from the EEPROM This parameter controls the automatic generation(Tx) and response(Rx) to Ethernet PAUSE frames. InterruptThrottleRate --------------------- + (not supported on Intel(R) 82542, 82543 or 82544-based adapters) -Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative, - 4=simplified balancing) -Default Value: 3 + +:Valid Range: + 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative, + 4=simplified balancing) +:Default Value: 3 The driver can limit the amount of interrupts per second that the adapter will generate for incoming packets. It does this by writing a value to the @@ -135,13 +145,15 @@ Setting InterruptThrottleRate to 0 turns off any interrupt moderation and may improve small packet latency, but is generally not suitable for bulk throughput traffic. -NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and +NOTE: + InterruptThrottleRate takes precedence over the TxAbsIntDelay and RxAbsIntDelay parameters. In other words, minimizing the receive and/or transmit absolute delays does not force the controller to generate more interrupts than what the Interrupt Throttle Rate allows. -CAUTION: If you are using the Intel(R) PRO/1000 CT Network Connection +CAUTION: + If you are using the Intel(R) PRO/1000 CT Network Connection (controller 82547), setting InterruptThrottleRate to a value greater than 75,000, may hang (stop transmitting) adapters under certain network conditions. If this occurs a NETDEV @@ -151,7 +163,8 @@ CAUTION: If you are using the Intel(R) PRO/1000 CT Network Connection hang, ensure that InterruptThrottleRate is set no greater than 75,000 and is not set to 0. -NOTE: When e1000 is loaded with default settings and multiple adapters +NOTE: + When e1000 is loaded with default settings and multiple adapters are in use simultaneously, the CPU utilization may increase non- linearly. In order to limit the CPU utilization without impacting the overall throughput, we recommend that you load the driver as @@ -168,9 +181,11 @@ NOTE: When e1000 is loaded with default settings and multiple adapters RxDescriptors ------------- -Valid Range: 48-256 for 82542 and 82543-based adapters - 48-4096 for all other supported adapters -Default Value: 256 + +:Valid Range: + - 48-256 for 82542 and 82543-based adapters + - 48-4096 for all other supported adapters +:Default Value: 256 This value specifies the number of receive buffer descriptors allocated by the driver. Increasing this value allows the driver to buffer more @@ -180,15 +195,17 @@ Each descriptor is 16 bytes. A receive buffer is also allocated for each descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending on the MTU setting. The maximum MTU size is 16110. -NOTE: MTU designates the frame size. It only needs to be set for Jumbo +NOTE: + MTU designates the frame size. It only needs to be set for Jumbo Frames. Depending on the available system resources, the request for a higher number of receive descriptors may be denied. In this case, use a lower number. RxIntDelay ---------- -Valid Range: 0-65535 (0=off) -Default Value: 0 + +:Valid Range: 0-65535 (0=off) +:Default Value: 0 This value delays the generation of receive interrupts in units of 1.024 microseconds. Receive interrupt reduction can improve CPU efficiency if @@ -198,7 +215,8 @@ of TCP traffic. If the system is reporting dropped receives, this value may be set too high, causing the driver to run out of available receive descriptors. -CAUTION: When setting RxIntDelay to a value other than 0, adapters may +CAUTION: + When setting RxIntDelay to a value other than 0, adapters may hang (stop transmitting) under certain network conditions. If this occurs a NETDEV WATCHDOG message is logged in the system event log. In addition, the controller is automatically reset, @@ -207,9 +225,11 @@ CAUTION: When setting RxIntDelay to a value other than 0, adapters may RxAbsIntDelay ------------- + (This parameter is supported only on 82540, 82545 and later adapters.) -Valid Range: 0-65535 (0=off) -Default Value: 128 + +:Valid Range: 0-65535 (0=off) +:Default Value: 128 This value, in units of 1.024 microseconds, limits the delay in which a receive interrupt is generated. Useful only if RxIntDelay is non-zero, @@ -220,9 +240,11 @@ conditions. Speed ----- + (This parameter is supported only on adapters with copper connections.) -Valid Settings: 0, 10, 100, 1000 -Default Value: 0 (auto-negotiate at all supported speeds) + +:Valid Settings: 0, 10, 100, 1000 +:Default Value: 0 (auto-negotiate at all supported speeds) Speed forces the line speed to the specified value in megabits per second (Mbps). If this parameter is not specified or is set to 0 and the link @@ -231,22 +253,26 @@ speed. Duplex should also be set when Speed is set to either 10 or 100. TxDescriptors ------------- -Valid Range: 48-256 for 82542 and 82543-based adapters - 48-4096 for all other supported adapters -Default Value: 256 + +:Valid Range: + - 48-256 for 82542 and 82543-based adapters + - 48-4096 for all other supported adapters +:Default Value: 256 This value is the number of transmit descriptors allocated by the driver. Increasing this value allows the driver to queue more transmits. Each descriptor is 16 bytes. -NOTE: Depending on the available system resources, the request for a +NOTE: + Depending on the available system resources, the request for a higher number of transmit descriptors may be denied. In this case, use a lower number. TxIntDelay ---------- -Valid Range: 0-65535 (0=off) -Default Value: 8 + +:Valid Range: 0-65535 (0=off) +:Default Value: 8 This value delays the generation of transmit interrupts in units of 1.024 microseconds. Transmit interrupt reduction can improve CPU @@ -256,9 +282,11 @@ causing the driver to run out of available transmit descriptors. TxAbsIntDelay ------------- + (This parameter is supported only on 82540, 82545 and later adapters.) -Valid Range: 0-65535 (0=off) -Default Value: 32 + +:Valid Range: 0-65535 (0=off) +:Default Value: 32 This value, in units of 1.024 microseconds, limits the delay in which a transmit interrupt is generated. Useful only if TxIntDelay is non-zero, @@ -269,18 +297,21 @@ network conditions. XsumRX ------ + (This parameter is NOT supported on the 82542-based adapter.) -Valid Range: 0-1 -Default Value: 1 + +:Valid Range: 0-1 +:Default Value: 1 A value of '1' indicates that the driver should enable IP checksum offload for received packets (both UDP and TCP) to the adapter hardware. Copybreak --------- -Valid Range: 0-xxxxxxx (0=off) -Default Value: 256 -Usage: modprobe e1000.ko copybreak=128 + +:Valid Range: 0-xxxxxxx (0=off) +:Default Value: 256 +:Usage: modprobe e1000.ko copybreak=128 Driver copies all packets below or equaling this size to a fresh RX buffer before handing it up the stack. @@ -292,8 +323,9 @@ it is also available during runtime at SmartPowerDownEnable -------------------- -Valid Range: 0-1 -Default Value: 0 (disabled) + +:Valid Range: 0-1 +:Default Value: 0 (disabled) Allows PHY to turn off in lower power states. The user can turn off this parameter in supported chipsets. @@ -309,14 +341,14 @@ fiber interface board only links at 1000 Mbps full-duplex. For copper-based boards, the keywords interact as follows: - The default operation is auto-negotiate. The board advertises all +- The default operation is auto-negotiate. The board advertises all supported speed and duplex combinations, and it links at the highest common speed and duplex mode IF the link partner is set to auto-negotiate. - If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps +- If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps is advertised (The 1000BaseT spec requires auto-negotiation.) - If Speed = 10 or 100, then both Speed and Duplex should be set. Auto- +- If Speed = 10 or 100, then both Speed and Duplex should be set. Auto- negotiation is disabled, and the AutoNeg parameter is ignored. Partner SHOULD also be forced. @@ -328,13 +360,15 @@ process. The parameter may be specified as either a decimal or hexadecimal value as determined by the bitmap below. +============== ====== ====== ======= ======= ====== ====== ======= ====== Bit position 7 6 5 4 3 2 1 0 Decimal Value 128 64 32 16 8 4 2 1 Hex value 80 40 20 10 8 4 2 1 Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10 Duplex Full Full Half Full Half +============== ====== ====== ======= ======= ====== ====== ======= ====== -Some examples of using AutoNeg: +Some examples of using AutoNeg:: modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half) modprobe e1000 AutoNeg=1 (Same as above) @@ -357,56 +391,59 @@ Additional Configurations Jumbo Frames ------------ -Jumbo Frames support is enabled by changing the MTU to a value larger -than the default of 1500. Use the ifconfig command to increase the MTU -size. For example:: + + Jumbo Frames support is enabled by changing the MTU to a value larger than + the default of 1500. Use the ifconfig command to increase the MTU size. + For example:: ifconfig eth mtu 9000 up -This setting is not saved across reboots. It can be made permanent if -you add:: + This setting is not saved across reboots. It can be made permanent if + you add:: MTU=9000 -to the file /etc/sysconfig/network-scripts/ifcfg-eth. This example -applies to the Red Hat distributions; other distributions may store this -setting in a different location. + to the file /etc/sysconfig/network-scripts/ifcfg-eth. This example + applies to the Red Hat distributions; other distributions may store this + setting in a different location. -Notes: Degradation in throughput performance may be observed in some -Jumbo frames environments. If this is observed, increasing the -application's socket buffer size and/or increasing the -/proc/sys/net/ipv4/tcp_*mem entry values may help. See the specific -application manual and /usr/src/linux*/Documentation/ -networking/ip-sysctl.txt for more details. +Notes: + Degradation in throughput performance may be observed in some Jumbo frames + environments. If this is observed, increasing the application's socket buffer + size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help. + See the specific application manual and /usr/src/linux*/Documentation/ + networking/ip-sysctl.txt for more details. -- The maximum MTU setting for Jumbo Frames is 16110. This value - coincides with the maximum Jumbo Frames size of 16128. + - The maximum MTU setting for Jumbo Frames is 16110. This value coincides + with the maximum Jumbo Frames size of 16128. -- Using Jumbo frames at 10 or 100 Mbps is not supported and may result - in poor performance or loss of link. + - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in + poor performance or loss of link. -- Adapters based on the Intel(R) 82542 and 82573V/E controller do not - support Jumbo Frames. These correspond to the following product names: - Intel(R) PRO/1000 Gigabit Server Adapter Intel(R) PRO/1000 PM Network - Connection + - Adapters based on the Intel(R) 82542 and 82573V/E controller do not + support Jumbo Frames. These correspond to the following product names:: + + Intel(R) PRO/1000 Gigabit Server Adapter + Intel(R) PRO/1000 PM Network Connection ethtool ------- -The driver utilizes the ethtool interface for driver configuration and -diagnostics, as well as displaying statistical information. The ethtool -version 1.6 or later is required for this functionality. -The latest release of ethtool can be found from -https://www.kernel.org/pub/software/network/ethtool/ + The driver utilizes the ethtool interface for driver configuration and + diagnostics, as well as displaying statistical information. The ethtool + version 1.6 or later is required for this functionality. + + The latest release of ethtool can be found from + https://www.kernel.org/pub/software/network/ethtool/ Enabling Wake on LAN* (WoL) --------------------------- -WoL is configured through the ethtool* utility. -WoL will be enabled on the system during the next shut down or reboot. -For this driver version, in order to enable WoL, the e1000 driver must be -loaded when shutting down or rebooting the system. + WoL is configured through the ethtool* utility. + WoL will be enabled on the system during the next shut down or reboot. + For this driver version, in order to enable WoL, the e1000 driver must be + loaded when shutting down or rebooting the system. Support ======= diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c index 3f5c350716bb..0bd1294ba517 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -1871,7 +1871,12 @@ s32 ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq, if (enable_addr != 0) rar_high |= IXGBE_RAH_AV; + /* Record lower 32 bits of MAC address and then make + * sure that write is flushed to hardware before writing + * the upper 16 bits and setting the valid bit. + */ IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low); + IXGBE_WRITE_FLUSH(hw); IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); return 0; @@ -1903,8 +1908,13 @@ s32 ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index) rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index)); rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV); - IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0); + /* Clear the address valid bit and upper 16 bits of the address + * before clearing the lower bits. This way we aren't updating + * a live filter. + */ IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high); + IXGBE_WRITE_FLUSH(hw); + IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0); /* clear VMDq pool/queue selection for this RAR */ hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL); diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c index c116f459945d..da4322e4daed 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c @@ -839,7 +839,7 @@ int ixgbe_ipsec_tx(struct ixgbe_ring *tx_ring, } itd->sa_idx = xs->xso.offload_handle - IXGBE_IPSEC_BASE_TX_INDEX; - if (unlikely(itd->sa_idx > IXGBE_IPSEC_MAX_SA_COUNT)) { + if (unlikely(itd->sa_idx >= IXGBE_IPSEC_MAX_SA_COUNT)) { netdev_err(tx_ring->netdev, "%s: bad sa_idx=%d handle=%lu\n", __func__, itd->sa_idx, xs->xso.offload_handle); return 0;